[ Upstream commit 280e3ebdaf ]
Check that the NFC_ATTR_FIRMWARE_NAME attributes are provided by
the netlink client prior to accessing them.This prevents potential
unhandled NULL pointer dereference exceptions which can be triggered
by malicious user-mode programs, if they omit one or both of these
attributes.
Similar to commit a0323b979f ("nfc: Ensure presence of required attributes in the activate_target handler").
Fixes: 9674da8759 ("NFC: Add firmware upload netlink command")
Signed-off-by: Defang Bo <bodefang@126.com>
Link: https://lore.kernel.org/r/1603107538-4744-1-git-send-email-bodefang@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7a12b5a0f ]
the following command
# tc action add action tunnel_key \
> set src_ip 2001:db8::1 dst_ip 2001:db8::2 id 10 erspan_opts 1:6789:0:0
generates the following splat:
BUG: KASAN: slab-out-of-bounds in tunnel_key_copy_opts+0xcc9/0x1010 [act_tunnel_key]
Write of size 4 at addr ffff88813f5f1cc8 by task tc/873
CPU: 2 PID: 873 Comm: tc Not tainted 5.9.0+ #282
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
Call Trace:
dump_stack+0x99/0xcb
print_address_description.constprop.7+0x1e/0x230
kasan_report.cold.13+0x37/0x7c
tunnel_key_copy_opts+0xcc9/0x1010 [act_tunnel_key]
tunnel_key_init+0x160c/0x1f40 [act_tunnel_key]
tcf_action_init_1+0x5b5/0x850
tcf_action_init+0x15d/0x370
tcf_action_add+0xd9/0x2f0
tc_ctl_action+0x29b/0x3a0
rtnetlink_rcv_msg+0x341/0x8d0
netlink_rcv_skb+0x120/0x380
netlink_unicast+0x439/0x630
netlink_sendmsg+0x719/0xbf0
sock_sendmsg+0xe2/0x110
____sys_sendmsg+0x5ba/0x890
___sys_sendmsg+0xe9/0x160
__sys_sendmsg+0xd3/0x170
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f872a96b338
Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55
RSP: 002b:00007ffffe367518 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 000000005f8f5aed RCX: 00007f872a96b338
RDX: 0000000000000000 RSI: 00007ffffe367580 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000001c
R10: 000000000000000b R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000686760 R14: 0000000000000601 R15: 0000000000000000
Allocated by task 873:
kasan_save_stack+0x19/0x40
__kasan_kmalloc.constprop.7+0xc1/0xd0
__kmalloc+0x151/0x310
metadata_dst_alloc+0x20/0x40
tunnel_key_init+0xfff/0x1f40 [act_tunnel_key]
tcf_action_init_1+0x5b5/0x850
tcf_action_init+0x15d/0x370
tcf_action_add+0xd9/0x2f0
tc_ctl_action+0x29b/0x3a0
rtnetlink_rcv_msg+0x341/0x8d0
netlink_rcv_skb+0x120/0x380
netlink_unicast+0x439/0x630
netlink_sendmsg+0x719/0xbf0
sock_sendmsg+0xe2/0x110
____sys_sendmsg+0x5ba/0x890
___sys_sendmsg+0xe9/0x160
__sys_sendmsg+0xd3/0x170
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at ffff88813f5f1c00
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 200 bytes inside of
256-byte region [ffff88813f5f1c00, ffff88813f5f1d00)
The buggy address belongs to the page:
page:0000000011b48a19 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x13f5f0
head:0000000011b48a19 order:1 compound_mapcount:0
flags: 0x17ffffc0010200(slab|head)
raw: 0017ffffc0010200 0000000000000000 0000000d00000001 ffff888107c43400
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88813f5f1b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88813f5f1c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff88813f5f1c80: 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc
^
ffff88813f5f1d00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88813f5f1d80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
using IPv6 tunnels, act_tunnel_key allocates a fixed amount of memory for
the tunnel metadata, but then it expects additional bytes to store tunnel
specific metadata with tunnel_key_copy_opts().
Fix the arguments of __ipv6_tun_set_dst(), so that 'md_size' contains the
size previously computed by tunnel_key_get_opts_len(), like it's done for
IPv4 tunnels.
Fixes: 0ed5269f9e ("net/sched: add tunnel option support to act_tunnel_key")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/36ebe969f6d13ff59912d6464a4356fe6f103766.1603231100.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fce1e43e2 ]
This driver calls ether_setup to set up the network device.
The ether_setup function would add the IFF_TX_SKB_SHARING flag to the
device. This flag indicates that it is safe to transmit shared skbs to
the device.
However, this is not true. This driver may pad the frame (in eth_tx)
before transmission, so the skb may be modified.
Fixes: 550fd08c2c ("net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared")
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020063420.187497-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01c4ceae0a ]
The hdlc_rcv function is used as hdlc_packet_type.func to process any
skb received in the kernel with skb->protocol == htons(ETH_P_HDLC).
The purpose of this function is to provide second-stage processing for
skbs not assigned a "real" L3 skb->protocol value in the first stage.
This function assumes the device from which the skb is received is an
HDLC device (a device created by this module). It assumes that
netdev_priv(dev) returns a pointer to "struct hdlc_device".
However, it is possible that some driver in the kernel (not necessarily
in our control) submits a received skb with skb->protocol ==
htons(ETH_P_HDLC), from a non-HDLC device. In this case, the skb would
still be received by hdlc_rcv. This will cause problems.
hdlc_rcv should be able to recognize and drop invalid skbs. It should
first make sure "dev" is actually an HDLC device, before starting its
processing. This patch adds this check to hdlc_rcv.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020013152.89259-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fb5f0160a ]
In chtls_sendpage() socket lock is released but not acquired,
fix it by taking lock.
Fixes: 36bedb3f2e ("crypto: chtls - Inline TLS record Tx")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3277cbfba upstream.
When releasing a thread todo list when tearing down
a binder_proc, the following race was possible which
could result in a use-after-free:
1. Thread 1: enter binder_release_work from binder_thread_release
2. Thread 2: binder_update_ref_for_handle() -> binder_dec_node_ilocked()
3. Thread 2: dec nodeA --> 0 (will free node)
4. Thread 1: ACQ inner_proc_lock
5. Thread 2: block on inner_proc_lock
6. Thread 1: dequeue work (BINDER_WORK_NODE, part of nodeA)
7. Thread 1: REL inner_proc_lock
8. Thread 2: ACQ inner_proc_lock
9. Thread 2: todo list cleanup, but work was already dequeued
10. Thread 2: free node
11. Thread 2: REL inner_proc_lock
12. Thread 1: deref w->type (UAF)
The problem was that for a BINDER_WORK_NODE, the binder_work element
must not be accessed after releasing the inner_proc_lock while
processing the todo list elements since another thread might be
handling a deref on the node containing the binder_work element
leading to the node being freed.
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20201009232455.4054810-1-tkjos@google.com
Cc: <stable@vger.kernel.org> # 4.14, 4.19, 5.4, 5.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea1dd3e9d0 ]
At first when sendpage gets called, if there is more data, 'more' in
tls_push_data() gets set which later sets pending_open_record_frags, but
when there is no more data in file left, and last time tls_push_data()
gets called, pending_open_record_frags doesn't get reset. And later when
2 bytes of encrypted alert comes as sendmsg, it first checks for
pending_open_record_frags, and since this is set, it creates a record with
0 data bytes to encrypt, meaning record length is prepend_size + tag_size
only, which causes problem.
We should set/reset pending_open_record_frags based on more bit.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef9da46dde ]
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02a1b175b0 ]
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed42989eab ]
skb_unshare() drops a reference count on the old skb unconditionally,
so in the failure case, we end up freeing the skb twice here.
And because the skb is allocated in fclone and cloned by caller
tipc_msg_reassemble(), the consequence is actually freeing the
original skb too, thus triggered the UAF by syzbot.
Fix this by replacing this skb_unshare() with skb_cloned()+skb_copy().
Fixes: ff48b6222e ("tipc: use skb_unshare() instead in tipc_buf_append()")
Reported-and-tested-by: syzbot+e96a7ba46281824cc46a@syzkaller.appspotmail.com
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef12ad4588 ]
The SMCD_DMBE_SIZES should include all valid DMBE buffer sizes, so the
correct value is 6 which means 1MB. With 7 the registration of an ISM
buffer would always fail because of the invalid size requested.
Fix that and set the value to 6.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6617dfd440 ]
Commit 4fc427e051 ("ipv6_route_seq_next should increase position index")
tried to fix the issue where seq_file pos is not increased
if a NULL element is returned with seq_ops->next(). See bug
https://bugzilla.kernel.org/show_bug.cgi?id=206283
The commit effectively does:
- increase pos for all seq_ops->start()
- increase pos for all seq_ops->next()
For ipv6_route, increasing pos for all seq_ops->next() is correct.
But increasing pos for seq_ops->start() is not correct
since pos is used to determine how many items to skip during
seq_ops->start():
iter->skip = *pos;
seq_ops->start() just fetches the *current* pos item.
The item can be skipped only after seq_ops->show() which essentially
is the beginning of seq_ops->next().
For example, I have 7 ipv6 route entries,
root@arch-fb-vm1:~/net-next dd if=/proc/net/ipv6_route bs=4096
00000000000000000000000000000000 40 00000000000000000000000000000000 00 00000000000000000000000000000000 00000400 00000001 00000000 00000001 eth0
fe800000000000000000000000000000 40 00000000000000000000000000000000 00 00000000000000000000000000000000 00000100 00000001 00000000 00000001 eth0
00000000000000000000000000000000 00 00000000000000000000000000000000 00 00000000000000000000000000000000 ffffffff 00000001 00000000 00200200 lo
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000003 00000000 80200001 lo
fe800000000000002050e3fffebd3be8 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000002 00000000 80200001 eth0
ff000000000000000000000000000000 08 00000000000000000000000000000000 00 00000000000000000000000000000000 00000100 00000004 00000000 00000001 eth0
00000000000000000000000000000000 00 00000000000000000000000000000000 00 00000000000000000000000000000000 ffffffff 00000001 00000000 00200200 lo
0+1 records in
0+1 records out
1050 bytes (1.0 kB, 1.0 KiB) copied, 0.00707908 s, 148 kB/s
root@arch-fb-vm1:~/net-next
In the above, I specify buffer size 4096, so all records can be returned
to user space with a single trip to the kernel.
If I use buffer size 128, since each record size is 149, internally
kernel seq_read() will read 149 into its internal buffer and return the data
to user space in two read() syscalls. Then user read() syscall will trigger
next seq_ops->start(). Since the current implementation increased pos even
for seq_ops->start(), it will skip record #2, #4 and #6, assuming the first
record is #1.
root@arch-fb-vm1:~/net-next dd if=/proc/net/ipv6_route bs=128
00000000000000000000000000000000 40 00000000000000000000000000000000 00 00000000000000000000000000000000 00000400 00000001 00000000 00000001 eth0
00000000000000000000000000000000 00 00000000000000000000000000000000 00 00000000000000000000000000000000 ffffffff 00000001 00000000 00200200 lo
fe800000000000002050e3fffebd3be8 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000002 00000000 80200001 eth0
00000000000000000000000000000000 00 00000000000000000000000000000000 00 00000000000000000000000000000000 ffffffff 00000001 00000000 00200200 lo
4+1 records in
4+1 records out
600 bytes copied, 0.00127758 s, 470 kB/s
To fix the problem, create a fake pos pointer so seq_ops->start()
won't actually increase seq_file pos. With this fix, the
above `dd` command with `bs=128` will show correct result.
Fixes: 4fc427e051 ("ipv6_route_seq_next should increase position index")
Cc: Alexei Starovoitov <ast@kernel.org>
Suggested-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0da1ccbbef ]
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64a632da53 ]
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2b8a92733 ]
netcons calls napi_poll with a budget of 0 to transmit packets.
Handle this by:
- skipping RX processing
- do not try to recycle TX packets to the RX cache
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 874fb9e2ca ]
Tobias reported regressions in IPsec tests following the patch
referenced by the Fixes tag below. The root cause is dropping the
reset of the flowi4_oif after the fib_lookup. Apparently it is
needed for xfrm cases, so restore the oif update to ip_route_output_flow
right before the call to xfrm_lookup_route.
Fixes: 2fbc6e89b2 ("ipv4: Update exception handling for multipath routes via same device")
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 413f142cc0 ]
Ingress large send packets are identified by either:
The IBMVETH_RXQ_LRG_PKT flag in the receive buffer
or with a -1 placed in the ip header checksum.
The method used depends on firmware version. Frame
geometry and sufficient header validation is performed by the
hypervisor eliminating the need for further header checks here.
Fixes: 7b5967389f ("ibmveth: set correct gso_size and gso_type")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Reviewed-by: Cristobal Forno <cris.forno@ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45cb6653b0 upstream.
Return -EINVAL for authenc(hmac(sha1),cbc(aes)),
authenc(hmac(sha256),cbc(aes)) and authenc(hmac(sha512),cbc(aes))
if the cipher length is not multiple of the AES block.
This is to prevent an undefined device behaviour.
Fixes: d370cec321 ("crypto: qat - Intel(R) QAT crypto interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dominik Przychodni <dominik.przychodni@intel.com>
[giovanni.cabiddu@intel.com: reworded commit message]
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10a2f0b311 upstream.
The setkey function for GCM/CCM algorithms didn't verify the key
length before copying the key and subtracting the salt length.
This patch delays the copying of the key til after the verification
has been done. It also adds checks on the key length to ensure
that it's at least as long as the salt.
Fixes: 9d12ba86f8 ("crypto: brcm - Add Broadcom SPU driver")
Cc: <stable@vger.kernel.org>
Reported-by: kiyin(尹亮) <kiyin@tencent.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2bb80b8bd upstream.
With suitably crafted reiserfs image and mount command reiserfs will
crash when trying to verify that XATTR_ROOT directory can be looked up
in / as that recurses back to xattr code like:
xattr_lookup+0x24/0x280 fs/reiserfs/xattr.c:395
reiserfs_xattr_get+0x89/0x540 fs/reiserfs/xattr.c:677
reiserfs_get_acl+0x63/0x690 fs/reiserfs/xattr_acl.c:209
get_acl+0x152/0x2e0 fs/posix_acl.c:141
check_acl fs/namei.c:277 [inline]
acl_permission_check fs/namei.c:309 [inline]
generic_permission+0x2ba/0x550 fs/namei.c:353
do_inode_permission fs/namei.c:398 [inline]
inode_permission+0x234/0x4a0 fs/namei.c:463
lookup_one_len+0xa6/0x200 fs/namei.c:2557
reiserfs_lookup_privroot+0x85/0x1e0 fs/reiserfs/xattr.c:972
reiserfs_fill_super+0x2b51/0x3240 fs/reiserfs/super.c:2176
mount_bdev+0x24f/0x360 fs/super.c:1417
Fix the problem by bailing from reiserfs_xattr_get() when xattrs are not
yet initialized.
CC: stable@vger.kernel.org
Reported-by: syzbot+9b33c9b118d77ff59b6f@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cf87e5edd upstream.
There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users. The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.
Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace. Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339ddaa626 upstream.
Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0 (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.
The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.
Fixes: 3ca44c16b0 ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ca44c16b0 upstream.
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Hans-Christian Noren Egtvedt <hegtvedt@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b560a208cd upstream.
This checks if BT_HS is enabled relecting it on MGMT_SETTING_HS instead
of always reporting it as supported.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19425641c upstream.
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5d0e49e8d ]
The commit fe00e50b2d ("ARM: 8858/1: vdso: use $(LD) instead of $(CC)
to link VDSO") removed the passing of CFLAGS, since ld doesn't take
those directly. However, prior, big-endian ARM was relying on gcc to
translate its -mbe8 option into ld's --be8 option. Lacking this, ld
generated be32 code, making the VDSO generate SIGILL when called by
userspace.
This commit passes --be8 if CONFIG_CPU_ENDIAN_BE8 is enabled.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe00e50b2d ]
We use $(LD) to link vmlinux, modules, decompressors, etc.
VDSO is the only exceptional case where $(CC) is used as the linker
driver, but I do not know why we need to do so. VDSO uses a special
linker script, and does not link standard libraries at all.
I changed the Makefile to use $(LD) rather than $(CC). I confirmed
the same vdso.so.raw was still produced.
Users will be able to use their favorite linker (e.g. lld instead of
of bfd) by passing LD= from the command line.
My plan is to rewrite all VDSO Makefiles to use $(LD), then delete
cc-ldoption.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4243219141 ]
In mmc_queue_setup_discard() the mmc driver queue's discard_granularity
might be set as 0 (when card->pref_erase > max_discard) while the mmc
device still declares to support discard operation. This is buggy and
triggered the following kernel warning message,
WARNING: CPU: 0 PID: 135 at __blkdev_issue_discard+0x200/0x294
CPU: 0 PID: 135 Comm: f2fs_discard-17 Not tainted 5.9.0-rc6 #1
Hardware name: Google Kevin (DT)
pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
pc : __blkdev_issue_discard+0x200/0x294
lr : __blkdev_issue_discard+0x54/0x294
sp : ffff800011dd3b10
x29: ffff800011dd3b10 x28: 0000000000000000 x27: ffff800011dd3cc4 x26: ffff800011dd3e18 x25: 000000000004e69b x24: 0000000000000c40 x23: ffff0000f1deaaf0 x22: ffff0000f2849200 x21: 00000000002734d8 x20: 0000000000000008 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000394 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 00000000000008b0 x9 : ffff800011dd3cb0 x8 : 000000000004e69b x7 : 0000000000000000 x6 : ffff0000f1926400 x5 : ffff0000f1940800 x4 : 0000000000000000 x3 : 0000000000000c40 x2 : 0000000000000008 x1 : 00000000002734d8 x0 : 0000000000000000 Call trace:
__blkdev_issue_discard+0x200/0x294
__submit_discard_cmd+0x128/0x374
__issue_discard_cmd_orderly+0x188/0x244
__issue_discard_cmd+0x2e8/0x33c
issue_discard_thread+0xe8/0x2f0
kthread+0x11c/0x120
ret_from_fork+0x10/0x1c
---[ end trace e4c8023d33dfe77a ]---
This patch fixes the issue by setting discard_granularity as SECTOR_SIZE
instead of 0 when (card->pref_erase > max_discard) is true. Now no more
complain from __blkdev_issue_discard() for the improper value of discard
granularity.
This issue is exposed after commit b35fd7422c ("block: check queue's
limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag
is also added for the commit to make sure people won't miss this patch
after applying the change of __blkdev_issue_discard().
Fixes: e056a1b5b6 ("mmc: queue: let host controllers specify maximum discard timeout")
Fixes: b35fd7422c ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()").
Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38b1dc47a3 ]
If someone calls setsockopt() twice to set a server key keyring, the first
keyring is leaked.
Fix it to return an error instead if the server key keyring is already set.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
