The HDAudio ASoC support relies on the set_tdm_slots() helper to store
the HDaudio stream tag in the tx_mask. This only works because of the
pre-existing order in soc-pcm.c, where the hw_params() is handled for
codec_dais *before* cpu_dais. When the order is reversed, the
stream_tag is used as a mask in the codec fixup functions:
/* fixup params based on TDM slot masks */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
codec_dai->tx_mask)
soc_pcm_codec_params_fixup(&codec_params,
codec_dai->tx_mask);
As a result of this confusion, the codec_params_fixup() ends-up
generating bad channel masks, depending on what stream_tag was
allocated.
We could add a flag to state that the tx_mask is really not a mask,
but it would be quite ugly to persist in overloading concepts.
Instead, this patch suggests a more generic get/set 'stream' API based
on the existing model for SoundWire. We can expand the concept to
store 'stream' opaque information that is specific to different DAI
types. In the case of HDAudio DAIs, we only need to store a stream tag
as an unsigned char pointer. The TDM rx_ and tx_masks should really
only be used to store masks.
Rename get_sdw_stream/set_sdw_stream callbacks and helpers as
get_stream/set_stream. No functionality change beyond the rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch provides both a simplification of the suspend flows and a
better balanced operation during suspend/resume transition, as part of
the transition of Sound Open Firmware (SOF) to dynamic pipelines: the
DSP resources are only enabled when required instead of enabled on
startup.
The exiting code relies on a convoluted way of dealing with suspend
signals. Since there is no .suspend DAI callback, we used the
component .suspend and marked all the component DAI dmas as
'suspended'. The information was used in the .prepare stage to
differentiate resume operations from xrun handling, and only
reinitialize SHIM registers and DMA in the former case.
While this solution has been working reliably for about 2 years, there
is a much better solution consisting in trapping the TRIGGER_SUSPEND
in the .trigger DAI ops. The DMA is still marked in the same way for
the .prepare op to run, but in addition the callbacks sent to DSP
firmware are now balanced.
Normal operation:
hw_params -> intel_params_stream
hw_free -> intel_free_stream
suspend -> intel_free_stream
prepare -> intel_params_stream
This balanced operation was not required with existing SOF firmware
relying on static pipelines instantiated at every boot. With the
on-going transition to dynamic pipelines, it's however a requirement
to keep the use count for the DAI widget balanced across all
transitions.
The component suspend is not removed but instead modified to deal with
a corner case: when a substream is PAUSED, the ALSA core does not
throw the TRIGGER_SUSPEND. This is problematic since the refcount for
all pipelines and widgets is not balanced, leading to issues on
resume. The trigger callback keeps track of the 'paused' state with a
new flag, which is tested during the component suspend called later to
release the remaining DSP resources. These resources will be
re-enabled in the .prepare step.
The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a
problem since the BE dailink is already marked as non-atomic.
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stephan Gerhold <stephan@gerhold.net>:
Some sound card setups might require extra pin switches to allow
turning off certain audio components. simple-card supports this
already using the "pin-switches" and "widgets" device tree property.
This series makes it possible to use the same properties for the Qcom
sound cards.
To implement that, the function that parses the "pin-switches" property
in simple-card-utils.c is first moved into the ASoC core. Then two
simple function calls are added to the common Qcom sound card DT parser.
Finally there is a small patch for the msm8916-wcd-analog codec to make
it possible to model sound card setups used in some MSM8916 smartphones.
(See PATCH 2/4 for an explanation of some real example use cases.)
Using pin switches rather than patching codec drivers with switches was
originally suggested by Mark Brown on a patch for the tfa989x codec:
https://lore.kernel.org/alsa-devel/YXaMVHo9drCIuD3u@sirena.org.uk/
The analog codec has separate output paths for the left headphone channel
(HPH_L) and the right headphone channel (HPH_R). While they are usually
used together for actual headphones output, some devices also have an
analog speaker amplifier connected to one of the headphone channels.
To allow modelling that properly (and to avoid powering on the unneeded
output path), HPH_L and HPH_R should be represented by separate outputs
rather than a shared HEADPHONE output that always activates both paths.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-5-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Some sound card setups might require extra pin switches to allow
turning off certain audio components. There are two real examples for
this in smartphones/tablets based on MSM8916:
1. Analog speaker amplifiers connected to headphone outputs.
The MSM8916 analog codec does not have a separate "Line Out" port
so some devices have an analog speaker amplifier connected to one
of the headphone outputs. A pin switch is necessary to allow
playback on headphones without also activating the speaker.
2. External speaker codec also used as earpiece.
Some smartphones have two front-facing (stereo) speakers that can
be also configured to act as an earpiece during voice calls. A pin
switch is needed to allow disabling the second speaker during
voice calls.
There are existing bindings that allow setting up such pin switches in
simple-card.yaml. Document the same for Qcom sound cards.
One variant of example 1 above is added to the examples in the DT
schema: There is an analog speaker amplifier connected to the HPH_R
(right headphone channel) output. Adding a "Speaker" pin switch and
widget allows turning off the speaker when audio should be only played
via the connected headphones.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211214142049.20422-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core already has several helpers to parse card properties
from the device tree. Move the parsing code for "pin-switches" from
simple-card-utils to a shared snd_soc_of_parse_pin_switches() function
so other drivers can also use it to set up pin switches configured in
the device tree.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
this series will improve how we are tracking the firmware's state to be able to
avoid communication with it when it is not going to answer due to a panic and
we will attempt to force power cycle the DSP to recover at the next runtime
suspend time.
The state handling brings in other improvements on the way the kernel reports
errors and DSP panics to reduce the printed lines for normal users, but at the
same time allowing developers (or for bug reports) to have more precise
information available to track down the issue.
We can now place messages easily in the correct debug level and not bound to the
static ERROR for some of the print chains, causing excess amount or partial
information to be printed, confusing users and machines (CI).
I would have prefered to split this series up, but it was developed together to
achieve a single goal to reduce the noise, but also provide the details we need
to be able to rootcause issues.
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
While at it also drop "r_irq" member from struct bcm_i2s_priv as there
are no users of it.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211221170100.27423-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211221170100.27423-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove non-existent properties from the example of the binding. These
properties were borrower from the old txt binding, but they were never
used in practice and aren't documented in the new binding. They aren't
reported by the binding checker because dtschema needs extra patch that
hasn't been upstreamed yet to make unevaluatedProperties work properly.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211216160229.17049-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
This patch-set tries to use dev_err_probe() helper function
instead of manual dev_err() code.
I hope ASoC will be more clean code by this patch-set.
