At least for 4430, trying to use the single conversion mode eventually
hangs the thermal sensor. This can be quite easily seen with errors:
thermal thermal_zone0: failed to read out thermal zone (-5)
Also, trying to read the temperature shows a stuck value with:
$ while true; do cat /sys/class/thermal/thermal_zone0/temp; done
Where the temperature is not rising at all with the busy loop.
Additionally, the EOCZ (end of conversion) bit is not rising on 4430 in
single conversion mode while it works fine in continuous conversion mode.
It is also possible that the hung temperature sensor can affect the
thermal shutdown alert too.
Let's fix the issue by adding TI_BANDGAP_FEATURE_CONT_MODE_ONLY flag and
use it for 4430.
Note that we also need to add udelay to for the EOCZ (end of conversion)
bit polling as otherwise we have it time out too early on 4430. We'll be
changing the loop to use iopoll in the following clean-up patch.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-3-tony@atomide.com
On dra7, there is no Start of Conversion (SOC) register bit and we have an
empty bgap_soc_mask in the configuration for the thermal driver. Let's not
do pointless reads and writes with the empty mask.
There's also no point waiting for End of Conversion bit (EOCZ) to go high
on dra7. We only care about it going down, and are now mostly timing out
waiting for EOCZ high while it has already gone down.
When we add checking for the timeout errors in a later patch, waiting for
EOCZ high would cause bogus time out errors.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-2-tony@atomide.com
The thermal zone can have cooling devices which are missing power actor
API. This could be due to missing Energy Model for devfreq or cpufreq
cooling device. In this case it is safe to fail the binding rather than
trying to workaround and control the temperature in such thermal zone.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210119114126.19480-1-lukasz.luba@arm.com
We are seeing thermal shutdown on Intel based mobile workstations, the
shutdown happens during the first trip handle in
thermal_zone_device_register():
kernel: thermal thermal_zone15: critical temperature reached (101 C), shutting down
However, we shouldn't do a thermal shutdown here, since
1) We may want to use a dedicated daemon, Intel's thermald in this case,
to handle thermal shutdown.
2) For ACPI based system, _CRT doesn't mean shutdown unless it's inside
ThermalZone namespace. ACPI Spec, 11.4.4 _CRT (Critical Temperature):
"... If this object it present under a device, the device’s driver
evaluates this object to determine the device’s critical cooling
temperature trip point. This value may then be used by the device’s
driver to program an internal device temperature sensor trip point."
So a "critical trip" here merely means we should take a more aggressive
cooling method.
As int340x device isn't present under ACPI ThermalZone, override the
default .critical callback to prevent surprising thermal shutdown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-1-kai.heng.feng@canonical.com
The function thermal_zone_device_reset() is called in the
thermal_zone_device_register() which allocates and initialize the
structure. The passive field is already zero-ed by the allocation, the
function is useless.
Call directly thermal_zone_device_init() instead and
thermal_zone_device_reset().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201222181110.1231977-1-daniel.lezcano@linaro.org
The code was reorganized in 2012 with the commit 0c01ebbfd3.
The main change is a loop on the trip points array and a unconditional
call to the throttle() ops of the governors for each of them even if
the trip temperature is not reached yet.
With this change, the 'forced_passive' is no longer checked in the
thermal_zone_device_update() function but in the step wise governor's
throttle() callback.
As the force_passive does no belong to the trip point array, the
thermal_zone_device_update() can not compare with the specified
passive temperature, thus does not detect the passive limit has been
crossed. Consequently, throttle() is never called and the
'forced_passive' branch is unreached.
In addition, the default processor cooling device is not automatically
bound to the thermal zone if there is not passive trip point, thus the
'forced_passive' can not operate.
If there is an active trip point, then the throttle function will be
called to mitigate at this temperature and the 'forced_passive' will
override the mitigation of the active trip point in this case but with
the default cooling device bound to the thermal zone, so usually a
fan, and that is not a passive cooling effect.
Given the regression exists since more than 8 years, nobody complained
and at the best of my knowledge there is no bug open in
https://bugzilla.kernel.org, it is reasonable to say it is unused.
Remove the 'forced_passive' related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-1-daniel.lezcano@linaro.org
qcom_vadc7_scale_hw_calib_die_temp() uses a table format different from
the rest of volt/temp conversion functions in this file. Also the
conversion functions results in non-monothonic values conversion, which
seems wrong.
Rewrite qcom_vadc7_scale_hw_calib_die_temp() to use
qcom_vadc_map_voltage_temp() directly, like the rest of conversion
functions do.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-10-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull s390 cleanups from Vasily Gorbik:
"Update defconfigs and sort config select list"
* tag 's390-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/Kconfig: sort config S390 select list once again
s390: update defconfigs
Pull power management fixes from Rafael Wysocki:
"These fix a crash in intel_pstate during resume from suspend-to-RAM
that may occur after recent changes and two resource leaks in error
paths in the operating performance points (OPP) framework, add a new
C-states table to intel_idle and update the cpuidle MAINTAINERS entry
to cover the governors too.
Specifics:
- Fix recently introduced crash in the intel_pstate driver that
occurs if scale-invariance is disabled during resume from
suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR
values made by the platform firmware (Rafael Wysocki).
- Fix a memory leak and add a missing clk_put() in error paths in the
OPP framework (Quanyang Wang, Viresh Kumar).
- Add new C-states table for SnowRidge processors to the intel_idle
driver (Artem Bityutskiy).
- Update the MAINTAINERS entry for cpuidle to make it clear that the
governors are covered by it too (Lukas Bulwahn)"
* tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: add SnowRidge C-state table
cpufreq: intel_pstate: Fix fast-switch fallback path
opp: Call the missing clk_put() on error
opp: fix memory leak in _allocate_opp_table
MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK
Pull SCSI fixes from James Bottomley:
"This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).
The big core two fixes are for power management ("block: Do not accept
any requests while suspended" and "block: Fix a race in the runtime
power management code") which finally sorts out the resume problems
we've occasionally been having.
To make the resume fix, there are seven necessary precursors which
effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
in block is automatically a power management exempt one.
All of the non-PM preempt cases are removed except for the one in the
SCSI Parallel Interface (spi) domain validation which is a genuine
case where we have to run requests at high priority to validate the
bus so this becomes an autopm get/put protected request"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
scsi: cxgb4i: Fix TLS dependency
scsi: ufs: Un-inline ufshcd_vops_device_reset function
scsi: ufs: Re-enable WriteBooster after device reset
scsi: ufs-mediatek: Use correct path to fix compile error
scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
scsi: block: Do not accept any requests while suspended
scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
scsi: block: Introduce BLK_MQ_REQ_PM
scsi: block: Fix a race in the runtime power management code
scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
scsi: ufs-pci: Fix restore from S4 for Intel controllers
scsi: ufs-mediatek: Keep VCC always-on for specific devices
scsi: ufs: Allow regulators being always-on
scsi: ufs: Clear UAC for RPMB after ufshcd resets
...
Pull block fixes from Jens Axboe:
"Two minor block fixes from this last week that should go into 5.11:
- Add missing NOWAIT debugfs definition (Andres)
- Fix kerneldoc warning introduced this merge window (Randy)"
* tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
block: add debugfs stanza for QUEUE_FLAG_NOWAIT
fs: block_dev.c: fix kernel-doc warnings from struct block_device changes
Pull io_uring fixes from Jens Axboe:
"A few fixes that should go into 5.11, all marked for stable as well:
- Fix issue around identity COW'ing and users that share a ring
across processes
- Fix a hang associated with unregistering fixed files (Pavel)
- Move the 'process is exiting' cancelation a bit earlier, so
task_works aren't affected by it (Pavel)"
* tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
kernel/io_uring: cancel io_uring before task works
io_uring: fix io_sqe_files_unregister() hangs
io_uring: add a helper for setting a ref node
io_uring: don't assume mm is constant across submits
Commit 436e980e2e ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).
Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For cancelling io_uring requests it needs either to be able to run
currently enqueued task_works or having it shut down by that moment.
Otherwise io_uring_cancel_files() may be waiting for requests that won't
ever complete.
Go with the first way and do cancellations before setting PF_EXITING and
so before putting the task_work infrastructure into a transition state
where task_work_run() would better not be called.
Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_sqe_files_unregister() uninterruptibly waits for enqueued ref nodes,
however requests keeping them may never complete, e.g. because of some
userspace dependency. Make sure it's interruptible otherwise it would
hang forever.
Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull ceph fixes from Ilya Dryomov:
"A fix for an edge case in MClientRequest encoding and a couple of
trivial fixups for the new msgr2 support"
* tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client:
libceph: add __maybe_unused to DEFINE_MSGR2_FEATURE
libceph: align session_key and con_secret to 16 bytes
libceph: fix auth_signature buffer allocation in secure mode
ceph: reencode gid_list when reconnecting
Add C-state table for the SnowRidge SoC which is found on Intel Jacobsville
platforms.
The following has been changed.
1. C1E latency changed from 10us to 15us. It was measured using the
open source "wult" tool (the "nic" method, 15us is the 99.99th
percentile).
2. C1E power break even changed from 20us to 25us, which may result
in less C1E residency in some workloads.
3. C6 latency changed from 50us to 130us. Measured the same way as C1E.
The C6 C-state is supported only by some SnowRidge revisions, so add a C-state
table commentary about this.
On SnowRidge, C6 support is enumerated via the usual mechanism: "mwait" leaf of
the "cpuid" instruction. The 'intel_idle' driver does check this leaf, so even
though C6 is present in the table, the driver will only use it if the CPU does
support it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When sugov_update_single_perf() falls back to the "frequency"
path due to the missing scale-invariance, it will call
cpufreq_driver_fast_switch() via sugov_fast_switch()
and the driver's ->fast_switch() callback will be invoked,
so it must not be NULL.
However, after commit a365ab6b9d ("cpufreq: intel_pstate: Implement
the ->adjust_perf() callback") intel_pstate sets ->fast_switch() to
NULL when it is going to use intel_cpufreq_adjust_perf(), which is a
mistake, because on x86 the scale-invariance may be turned off
dynamically, so modify it to retain the original ->adjust_perf()
callback pointer.
Fixes: a365ab6b9d ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull operating performance points (OPP) framework fixes for 5.11-rc2
from Viresh Kumar:
"This contains two patches to fix freeing of resources in error paths."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Call the missing clk_put() on error
opp: fix memory leak in _allocate_opp_table
