[ Upstream commit 8d61f926d4 ]
syzbot reported a possible deadlock in netlink_set_err() [1]
A similar issue was fixed in commit 1d482e666b ("netlink: disable IRQs
for netlink_lock_table()") in netlink_lock_table()
This patch adds IRQ safety to netlink_set_err() and __netlink_diag_dump()
which were not covered by cited commit.
[1]
WARNING: possible irq lock inversion dependency detected
6.4.0-rc6-syzkaller-00240-g4e9f0ec38852 #0 Not tainted
syz-executor.2/23011 just changed the state of lock:
ffffffff8e1a7a58 (nl_table_lock){.+.?}-{2:2}, at: netlink_set_err+0x2e/0x3a0 net/netlink/af_netlink.c:1612
but this lock was taken by another, SOFTIRQ-safe lock in the past:
(&local->queue_stop_reason_lock){..-.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(nl_table_lock);
local_irq_disable();
lock(&local->queue_stop_reason_lock);
lock(nl_table_lock);
<Interrupt>
lock(&local->queue_stop_reason_lock);
*** DEADLOCK ***
Fixes: 1d482e666b ("netlink: disable IRQs for netlink_lock_table()")
Reported-by: syzbot+a7d200a347f912723e5c@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=a7d200a347f912723e5c
Link: https://lore.kernel.org/netdev/000000000000e38d1605fea5747e@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230621154337.1668594-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fde4c557f ]
The Stuff Bit Count is always coded on 4 bits [1]. Update the Stuff
Bit Count size accordingly.
In addition, the CRC fields of CAN FD Frames contain stuff bits at
fixed positions called fixed stuff bits [2]. The CRC field starts with
a fixed stuff bit and then has another fixed stuff bit after each
fourth bit [2], which allows us to derive this formula:
FSB count = 1 + round_down(len(CRC field)/4)
The length of the CRC field is [1]:
len(CRC field) = len(Stuff Bit Count) + len(CRC)
= 4 + len(CRC)
with len(CRC) either 17 or 21 bits depending of the payload length.
In conclusion, for CRC17:
FSB count = 1 + round_down((4 + 17)/4)
= 6
and for CRC 21:
FSB count = 1 + round_down((4 + 21)/4)
= 7
Add a Fixed Stuff bits (FSB) field with above values and update
CANFD_FRAME_OVERHEAD_SFF and CANFD_FRAME_OVERHEAD_EFF accordingly.
[1] ISO 11898-1:2015 section 10.4.2.6 "CRC field":
The CRC field shall contain the CRC sequence followed by a recessive
CRC delimiter. For FD Frames, the CRC field shall also contain the
stuff count.
Stuff count
If FD Frames, the stuff count shall be at the beginning of the CRC
field. It shall consist of the stuff bit count modulo 8 in a 3-bit
gray code followed by a parity bit [...]
[2] ISO 11898-1:2015 paragraph 10.5 "Frame coding":
In the CRC field of FD Frames, the stuff bits shall be inserted at
fixed positions; they are called fixed stuff bits. There shall be a
fixed stuff bit before the first bit of the stuff count, even if the
last bits of the preceding field are a sequence of five consecutive
bits of identical value, there shall be only the fixed stuff bit,
there shall not be two consecutive stuff bits. A further fixed stuff
bit shall be inserted after each fourth bit of the CRC field [...]
Fixes: 85d99c3e2a ("can: length: can_skb_get_frame_len(): introduce function to get data length of frame in data link layer")
Suggested-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Link: https://lore.kernel.org/all/20230611025728.450837-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5cb79762 ]
When calling bpf_sk_lookup_tcp(), bpf_sk_lookup_udp() or
bpf_skc_lookup_tcp() from tc/xdp ingress, VRF socket bindings aren't
respoected, i.e. unbound sockets are returned, and bound sockets aren't
found.
VRF binding is determined by the sdif argument to sk_lookup(), however
when called from tc the IP SKB control block isn't initialized and thus
inet{,6}_sdif() always returns 0.
Fix by calculating sdif for the tc/xdp flows by observing the device's
l3 enslaved state.
The cg/sk_skb hooking points which are expected to support
inet{,6}_sdif() pass sdif=-1 which makes __bpf_skc_lookup() use the
existing logic.
Fixes: 6acc9b432e ("bpf: Add helper to retrieve socket in BPF")
Signed-off-by: Gilad Sever <gilad9366@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/bpf/20230621104211.301902-4-gilad9366@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e98730bc0 ]
Change BPF helper socket lookup functions to use TC specific variants:
bpf_tc_sk_lookup_tcp() / bpf_tc_sk_lookup_udp() / bpf_tc_skc_lookup_tcp()
instead of sharing implementation with the cg / sk_skb hooking points.
This allows introducing a separate logic for the TC flow.
The tc functions are identical to the original code.
Signed-off-by: Gilad Sever <gilad9366@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20230621104211.301902-2-gilad9366@gmail.com
Stable-dep-of: 9a5cb79762 ("bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c467c8f081 ]
This microSD card never clears Flush Cache bit after cache flush has
been started in sd_flush_cache(). This leads e.g. to failure to mount
file system. Add a quirk which disables the SD cache for this specific
card from specific manufacturing date of 11/2019, since on newer dated
cards from 05/2023 the cache flush works correctly.
Fixes: 08ebf903af ("mmc: core: Fixup support for writeback-cache for eMMC and SD")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230620102713.7701-1-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1403b109c9 ]
The common size is part of the length in the data
so don't add it again.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: ce6e1f600b ("wifi: ieee80211: Fix the common size calculation for reconfiguration ML")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39432f8a37 ]
The removed code ran for any BSS that was not included in the MBSSID
element in order to update it. However, instead of using the correct
inheritance rules, it would simply copy the elements from the
transmitting AP. The result is that we would report incorrect elements
in this case.
After some discussions, it seems that there are likely not even APs
actually using this feature. Either way, removing the code decreases
complexity and makes the cfg80211 behaviour more correct.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094949.cfd6d8db1f26.Ia1044902b86cd7d366400a4bfb93691b8f05d68c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd9aa3e7a ]
The cfg80211_gen_new_ie function merges the IEs using inheritance rules.
Rewrite this function to fix issues around inheritance rules. In
particular, vendor elements do not require any special handling, as they
are either all inherited or overridden by the subprofile.
Also, add fragmentation handling as this may be needed in some cases.
This also changes the function to not require making a copy. The new
version could be optimized a bit by explicitly tracking which IEs have
been handled already rather than looking that up again every time.
Note that a small behavioural change is the removal of the SSID special
handling. This should be fine for the MBSSID element, as the SSID must
be included in the subelement.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094949.bc6152e146db.I2b5f3bc45085e1901e5b5192a674436adaf94748@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0e21fa44 ]
This filter already exists for excluding IPv6 SNMP stats. Extend its
definition to also exclude IFLA_VF_INFO stats in RTM_GETLINK.
This patch constitutes a partial fix for a netlink attribute nesting
overflow bug in IFLA_VFINFO_LIST. By excluding the stats when the
requester doesn't need them, the truncation of the VF list is avoided.
While it was technically only the stats added in commit c5a9f6f0ab
("net/core: Add drop counters to VF statistics") breaking the camel's
back, the appreciable size of the stats data should never have been
included without due consideration for the maximum number of VFs
supported by PCI.
Fixes: 3b766cd832 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: c5a9f6f0ab ("net/core: Add drop counters to VF statistics")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Cc: Edwin Peer <espeer@gmail.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20230611105108.122586-1-gal@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75086cc6de ]
On EDMA capable hardware, ath9k_txq_list_has_key() can enter infinite
loop if it is called while all txq_fifos have packets that use different
key that the one we are looking for. Fix it by exiting the loop if all
txq_fifos have been checked already.
Because this loop is called under spin_lock_bh() (see ath_txq_lock) it
causes the following rcu stall:
rcu: INFO: rcu_sched self-detected stall on CPU
ath10k_pci 0000:01:00.0: failed to read temperature -11
rcu: 1-....: (5254 ticks this GP) idle=189/1/0x4000000000000002 softirq=8442983/8442984 fqs=2579
(t=5257 jiffies g=17983297 q=334)
Task dump for CPU 1:
task:hostapd state:R running task stack: 0 pid: 297 ppid: 289 flags:0x0000000a
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x1c/0x24
sched_show_task+0x140/0x170
dump_cpu_task+0x48/0x54
rcu_dump_cpu_stacks+0xf0/0x134
rcu_sched_clock_irq+0x8d8/0x9fc
update_process_times+0xa0/0xec
tick_sched_timer+0x5c/0xd0
__hrtimer_run_queues+0x154/0x320
hrtimer_interrupt+0x120/0x2f0
arch_timer_handler_virt+0x38/0x44
handle_percpu_devid_irq+0x9c/0x1e0
handle_domain_irq+0x64/0x90
gic_handle_irq+0x78/0xb0
call_on_irq_stack+0x28/0x38
do_interrupt_handler+0x54/0x5c
el1_interrupt+0x2c/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x74/0x78
ath9k_txq_has_key+0x1bc/0x250 [ath9k]
ath9k_set_key+0x1cc/0x3dc [ath9k]
drv_set_key+0x78/0x170
ieee80211_key_replace+0x564/0x6cc
ieee80211_key_link+0x174/0x220
ieee80211_add_key+0x11c/0x300
nl80211_new_key+0x12c/0x330
genl_family_rcv_msg_doit+0xbc/0x11c
genl_rcv_msg+0xd8/0x1c4
netlink_rcv_skb+0x40/0x100
genl_rcv+0x3c/0x50
netlink_unicast+0x1ec/0x2c0
netlink_sendmsg+0x198/0x3c0
____sys_sendmsg+0x210/0x250
___sys_sendmsg+0x78/0xc4
__sys_sendmsg+0x4c/0x90
__arm64_sys_sendmsg+0x28/0x30
invoke_syscall.constprop.0+0x60/0x100
do_el0_svc+0x48/0xd0
el0_svc+0x14/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x158/0x15c
This rcu stall is hard to reproduce as is, but changing ATH_TXFIFO_DEPTH
from 8 to 2 makes it reasonably easy to reproduce.
Fixes: ca2848022c ("ath9k: Postpone key cache entry deletion for TXQ frames reference it")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609093744.1985-1-repk@triplefau.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 434587df9f ]
There are no other files referencing this function, apparently
it was left global to avoid an 'unused function' warning when
the only caller is left out. With a 'W=1' build, it causes
a 'missing prototype' warning though:
drivers/memstick/host/r592.c:47:13: error: no previous prototype for 'memstick_debug_get_tpc_name' [-Werror=missing-prototypes]
Annotate the function as 'static __maybe_unused' to avoid both
problems.
Fixes: 9263412501 ("memstick: add driver for Ricoh R5C592 card reader")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516202714.560929-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cba6c4309 ]
Patch series "kexec: enable kexec_crash_size to support two crash kernel
regions".
When crashkernel=X fails to reserve region under 4G, it will fall back to
reserve region above 4G and a region of the default size will also be
reserved under 4G. Unfortunately, /sys/kernel/kexec_crash_size only
supports one crash kernel region now, the user cannot sense the low memory
reserved by reading /sys/kernel/kexec_crash_size. Also, low memory cannot
be freed by writing this file.
For example:
resource_size(crashk_res) = 512M
resource_size(crashk_low_res) = 256M
The result of 'cat /sys/kernel/kexec_crash_size' is 512M, but it should be
768M. When we execute 'echo 0 > /sys/kernel/kexec_crash_size', the size
of crashk_res becomes 0 and resource_size(crashk_low_res) is still 256 MB,
which is incorrect.
Since crashk_res manages the memory with high address and crashk_low_res
manages the memory with low address, crashk_low_res is shrunken only when
all crashk_res is shrunken. And because when there is only one crash
kernel region, crashk_res is always used. Therefore, if all crashk_res is
shrunken and crashk_low_res still exists, swap them.
This patch (of 6):
If the value of parameter 'new_size' is in the semi-open and semi-closed
interval (crashk_res.end - KEXEC_CRASH_MEM_ALIGN + 1, crashk_res.end], the
calculation result of ram_res is:
ram_res->start = crashk_res.end + 1
ram_res->end = crashk_res.end
The operation of insert_resource() fails, and ram_res is not added to
iomem_resource. As a result, the memory of the control block ram_res is
leaked.
In fact, on all architectures, the start address and size of crashk_res
are already aligned by KEXEC_CRASH_MEM_ALIGN. Therefore, we do not need
to round up crashk_res.start again. Instead, we should round up
'new_size' in advance.
Link: https://lkml.kernel.org/r/20230527123439.772-1-thunder.leizhen@huawei.com
Link: https://lkml.kernel.org/r/20230527123439.772-2-thunder.leizhen@huawei.com
Fixes: 6480e5a092 ("kdump: add missing RAM resource in crash_shrink_memory()")
Fixes: 06a7f71124 ("kexec: premit reduction of the reserved memory size")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e8b2c88fc ]
The ice_ptp_extts_work() and ice_ptp_periodic_work() functions are both
scheduled on the same kthread worker, pf.ptp.kworker. The
ice_ptp_periodic_work() function sends to the firmware to interact with the
PHY, and must block to wait for responses.
This can cause delay in responding to the PFINT_OICR_TSYN_EVNT interrupt
cause, ultimately resulting in disruption to processing an input signal of
the frequency is high enough. In our testing, even 100 Hz signals get
disrupted.
Fix this by instead processing the signal inside the miscellaneous
interrupt thread prior to handling Tx timestamps.
Use atomic bits in a new pf->misc_thread bitmap in order to safely
communicate which tasks require processing within the
ice_misc_intr_thread_fn(). This ensures the communication of desired tasks
from the ice_misc_intr() are correctly processed without racing even in the
event that the interrupt triggers again before the thread function exits.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b241e26082 ]
In case WoWlan was never configured during the operation of the system,
the hw->wiphy->wowlan_config will be NULL. rsi_config_wowlan() checks
whether wowlan_config is non-NULL and if it is not, then WARNs about it.
The warning is valid, as during normal operation the rsi_config_wowlan()
should only ever be called with non-NULL wowlan_config. In shutdown this
rsi_config_wowlan() should only ever be called if WoWlan was configured
before by the user.
Add checks for non-NULL wowlan_config into the shutdown hook. While at it,
check whether the wiphy is also non-NULL before accessing wowlan_config .
Drop the single-use wowlan_config variable, just inline it into function
call.
Fixes: 16bbc3eb83 ("rsi: fix null pointer dereference during rsi_shutdown()")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527222833.273741-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75bd32f5ce ]
Currently, on WCN3990, the station disconnect after hardware recovery is
not working as expected. This is because of setting the
IEEE80211_SDATA_DISCONNECT_HW_RESTART flag very early in the hardware
recovery process even before the driver invokes ieee80211_hw_restart().
On the contrary, mac80211 expects this flag to be set after
ieee80211_hw_restart() is invoked for it to trigger station disconnect.
Set the IEEE80211_SDATA_DISCONNECT_HW_RESTART flag in
ath10k_reconfig_complete() instead to fix this.
The other targets are not affected by this change, since the hardware
params flag is not set.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Fixes: 2c3fc50591 ("ath10k: Trigger sta disconnect on hardware restart")
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230518101515.3820-1-quic_youghand@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60548b825b ]
Default samples/pktgen scripts send 60 byte packets as hardware adds
4-bytes FCS checksum, which fulfils minimum Ethernet 64 bytes frame
size.
XDP layer will not necessary have access to the 4-bytes FCS checksum.
This leads to bpf_xdp_load_bytes() failing as it tries to copy 64-bytes
from an XDP packet that only have 60-bytes available.
Fixes: 7722517422 ("samples/bpf: fixup some tools to be able to support xdp multibuffer")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/168545704139.2996228.2516528552939485216.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08880713ce ]
If CONFIG_DEBUG_FS is not set:
regulator: Failed to create debugfs directory
...
regulator-dummy: Failed to create debugfs directory
As per the comments for debugfs_create_dir(), errors returned by this
function should be expected, and ignored:
* If debugfs is not enabled in the kernel, the value -%ENODEV will be
* returned.
*
* NOTE: it's expected that most callers should _ignore_ the errors returned
* by this function. Other debugfs functions handle the fact that the "dentry"
* passed to them could be an error and they don't crash in that case.
* Drivers should generally work fine even if debugfs fails to init anyway.
Adhere to the debugfs spirit, and streamline all operations by:
1. Demoting the importance of the printed error messages to debug
level, like is already done in create_regulator(),
2. Further ignoring any returned errors, as by design, all debugfs
functions are no-ops when passed an error pointer.
Fixes: 2bf1c45be3 ("regulator: Fix error checking for debugfs_create_dir")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f8bb6e113359ddfab7b59e4d4274bd4c06d6d0a.1685013051.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f04a32b2c5 ]
The sign-file utility (from scripts/) is used in prog_tests/verify_pkcs7_sig.c,
but the utility should not be called as a test. Executing this utility produces
the following error:
selftests: /linux/tools/testing/selftests/bpf: urandom_read
ok 16 selftests: /linux/tools/testing/selftests/bpf: urandom_read
selftests: /linux/tools/testing/selftests/bpf: sign-file
not ok 17 selftests: /linux/tools/testing/selftests/bpf: sign-file # exit=2
Also, urandom_read is mistakenly used as a test. It does not lead to an error,
but should be moved over to TEST_GEN_FILES as well. The empty TEST_CUSTOM_PROGS
can then be removed.
Fixes: fc97590668 ("selftests/bpf: Add test for bpf_verify_pkcs7_signature() kfunc")
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/ZEuWFk3QyML9y5QQ@example.org
Link: https://lore.kernel.org/bpf/88e3ab23029d726a2703adcf6af8356f7a2d3483.1684316821.git.legion@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 108598c39e ]
If it fails to attach fentry, the allocated bpf trampoline image will be
left in the system. That can be verified by checking /proc/kallsyms.
This meamleak can be verified by a simple bpf program as follows:
SEC("fentry/trap_init")
int fentry_run()
{
return 0;
}
It will fail to attach trap_init because this function is freed after
kernel init, and then we can find the trampoline image is left in the
system by checking /proc/kallsyms.
$ tail /proc/kallsyms
ffffffffc0613000 t bpf_trampoline_6442453466_1 [bpf]
ffffffffc06c3000 t bpf_trampoline_6442453466_1 [bpf]
$ bpftool btf dump file /sys/kernel/btf/vmlinux | grep "FUNC 'trap_init'"
[2522] FUNC 'trap_init' type_id=119 linkage=static
$ echo $((6442453466 & 0x7fffffff))
2522
Note that there are two left bpf trampoline images, that is because the
libbpf will fallback to raw tracepoint if -EINVAL is returned.
Fixes: e21aa34178 ("bpf: Fix fexit trampoline.")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Link: https://lore.kernel.org/bpf/20230515130849.57502-2-laoar.shao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47e79cbeea ]
After commit e21aa34178 ("bpf: Fix fexit trampoline."), the selector is only
used to indicate how many times the bpf trampoline image are updated and been
displayed in the trampoline ksym name. After the trampoline is freed, the
selector will start from 0 again. So the selector is a useless value to the
user. We can remove it.
If the user want to check whether the bpf trampoline image has been updated
or not, the user can compare the address. Each time the trampoline image is
updated, the address will change consequently. Jiri also pointed out another
issue that perf is still using the old name "bpf_trampoline_%lu", so this
change can fix the issue in perf.
Fixes: e21aa34178 ("bpf: Fix fexit trampoline.")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Link: https://lore.kernel.org/bpf/ZFvOOlrmHiY9AgXE@krava
Link: https://lore.kernel.org/bpf/20230515130849.57502-3-laoar.shao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04cb8453a9 ]
On aarch64, "bpftool feature" reports an incorrect BPF JIT limit:
$ sudo /sbin/bpftool feature
Scanning system configuration...
bpf() syscall restricted to privileged users
JIT compiler is enabled
JIT compiler hardening is disabled
JIT compiler kallsyms exports are enabled for root
skipping kernel config, can't open file: No such file or directory
Global memory limit for JIT compiler for unprivileged users is -201326592 bytes
This is because /proc/sys/net/core/bpf_jit_limit reports
$ sudo cat /proc/sys/net/core/bpf_jit_limit
68169519595520
...and an int is assumed in read_procfs(). Change read_procfs()
to return a long to avoid negative value reporting.
Fixes: 7a4522bbef ("tools: bpftool: add probes for /proc/ eBPF parameters")
Reported-by: Nicky Veitch <nicky.veitch@oracle.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20230512113134.58996-1-alan.maguire@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9b41daa5 ]
If sock->service_name is NULL, the local variable
service_name_tlv_length will not be assigned by nfc_llcp_build_tlv(),
later leading to using value frmo the stack. Smatch warning:
net/nfc/llcp_commands.c:442 nfc_llcp_send_connect() error: uninitialized symbol 'service_name_tlv_length'.
Fixes: de9e5aeb4f ("NFC: llcp: Fix usage of llcp_add_tlv()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
