Changes in 5.15.72
ALSA: hda: Do disconnect jacks at codec unbind
ALSA: hda: Fix hang at HD-audio codec unbinding due to refcount saturation
ALSA: hda: Fix Nvidia dp infoframe
ALSA: hda/realtek: fix speakers and micmute on HP 855 G8
cgroup: reduce dependency on cgroup_mutex
cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
uas: add no-uas quirk for Hiksemi usb_disk
usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS
uas: ignore UAS for Thinkplus chips
usb: typec: ucsi: Remove incorrect warning
thunderbolt: Explicitly reset plug events delay back to USB4 spec value
net: usb: qmi_wwan: Add new usb-id for Dell branded EM7455
Input: snvs_pwrkey - fix SNVS_HPVIDR1 register address
can: c_can: don't cache TX messages for C_CAN cores
clk: ingenic-tcu: Properly enable registers before accessing timers
x86/sgx: Do not fail on incomplete sanitization on premature stop of ksgxd
ARM: dts: integrator: Tag PCI host with device_type
ntfs: fix BUG_ON in ntfs_lookup_inode_by_name()
mm/damon/dbgfs: fix memory leak when using debugfs_lookup()
net: mt7531: only do PLL once after the reset
Revert "firmware: arm_scmi: Add clock management to the SCMI power domain"
drm/i915/gt: Restrict forced preemption to the active context
drm/amdgpu: Add amdgpu suspend-resume code path under SRIOV
vduse: prevent uninitialized memory accesses
libata: add ATA_HORKAGE_NOLPM for Pioneer BDR-207M and BDR-205
mmc: moxart: fix 4-bit bus width and remove 8-bit bus width
mmc: hsq: Fix data stomping during mmc recovery
mm/page_alloc: fix race condition between build_all_zonelists and page allocation
mm: prevent page_frag_alloc() from corrupting the memory
mm: fix dereferencing possible ERR_PTR
mm/migrate_device.c: flush TLB while holding PTL
mm: fix madivse_pageout mishandling on non-LRU page
mm,hwpoison: check mm when killing accessing process
media: dvb_vb2: fix possible out of bound access
media: rkvdec: Disable H.264 error detection
media: v4l2-compat-ioctl32.c: zero buffer passed to v4l2_compat_get_array_args()
swiotlb: max mapping size takes min align mask into account
ARM: dts: am33xx: Fix MMCHS0 dma properties
reset: imx7: Fix the iMX8MP PCIe PHY PERST support
ARM: dts: am5748: keep usb4_tm disabled
soc: sunxi: sram: Actually claim SRAM regions
soc: sunxi: sram: Prevent the driver from being unbound
soc: sunxi_sram: Make use of the helper function devm_platform_ioremap_resource()
soc: sunxi: sram: Fix probe function ordering issues
soc: sunxi: sram: Fix debugfs info for A64 SRAM C
ASoC: imx-card: Fix refcount issue with of_node_put
arm64: dts: qcom: sm8350: fix UFS PHY serdes size
ASoC: tas2770: Reinit regcache on reset
drm/bridge: lt8912b: add vsync hsync
drm/bridge: lt8912b: set hdmi or dvi mode
drm/bridge: lt8912b: fix corrupted image output
Revert "drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time"
Input: melfas_mip4 - fix return value check in mip4_probe()
gpio: mvebu: Fix check for pwm support on non-A8K platforms
usbnet: Fix memory leak in usbnet_disconnect()
net: sched: act_ct: fix possible refcount leak in tcf_ct_init()
cxgb4: fix missing unlock on ETHOFLD desc collect fail path
net/mlxbf_gige: Fix an IS_ERR() vs NULL bug in mlxbf_gige_mdio_probe
nvme: Fix IOC_PR_CLEAR and IOC_PR_RELEASE ioctls for nvme devices
wifi: mac80211: fix regression with non-QoS drivers
net: stmmac: power up/down serdes in stmmac_open/release
net: phy: Don't WARN for PHY_UP state in mdio_bus_phy_resume()
selftests: Fix the if conditions of in test_extra_filter()
vdpa/ifcvf: fix the calculation of queuepair
fs: split off setxattr_copy and do_setxattr function from setxattr
clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks
clk: iproc: Do not rely on node name for correct PLL setup
KVM: x86: Hide IA32_PLATFORM_DCA_CAP[31:0] from the guest
x86/alternative: Fix race in try_get_desc()
drm/i915/gem: Really move i915_gem_context.link under ref protection
Linux 5.15.72
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Ib8569de2af78d5080b026a46196aad5fc816fd42
commit efd608fa74 upstream.
I encountered some occasional crashes of poke_int3_handler() when
kprobes are set, while accessing desc->vec.
The text poke mechanism claims to have an RCU-like behavior, but it
does not appear that there is any quiescent state to ensure that
nobody holds reference to desc. As a result, the following race
appears to be possible, which can lead to memory corruption.
CPU0 CPU1
---- ----
text_poke_bp_batch()
-> smp_store_release(&bp_desc, &desc)
[ notice that desc is on
the stack ]
poke_int3_handler()
[ int3 might be kprobe's
so sync events are do not
help ]
-> try_get_desc(descp=&bp_desc)
desc = __READ_ONCE(bp_desc)
if (!desc) [false, success]
WRITE_ONCE(bp_desc, NULL);
atomic_dec_and_test(&desc.refs)
[ success, desc space on the stack
is being reused and might have
non-zero value. ]
arch_atomic_inc_not_zero(&desc->refs)
[ might succeed since desc points to
stack memory that was freed and might
be reused. ]
Fix this issue with small backportable patch. Instead of trying to
make RCU-like behavior for bp_desc, just eliminate the unnecessary
level of indirection of bp_desc, and hold the whole descriptor as a
global. Anyhow, there is only a single descriptor at any given
moment.
Fixes: 1f676247f3 ("x86/alternatives: Implement a better poke_int3_handler() completion scheme")
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@kernel.org
Link: https://lkml.kernel.org/r/20220920224743.3089-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aae2e72229 ]
The only thing reported by CPUID.9 is the value of
IA32_PLATFORM_DCA_CAP[31:0] in EAX. This MSR doesn't even exist in the
guest, since CPUID.1:ECX.DCA[bit 18] is clear in the guest.
Clear CPUID.9 in KVM_GET_SUPPORTED_CPUID.
Fixes: 24c82e576b ("KVM: Sanitize cpuid")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220922231854.249383-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b24a132eb ]
After commit 31fd9b79dc ("ARM: dts: BCM5301X: update CRU block
description") a warning from clk-iproc-pll.c was generated due to a
duplicate PLL name as well as the console stopped working. Upon closer
inspection it became clear that iproc_pll_clk_setup() used the Device
Tree node unit name as an unique identifier as well as a parent name to
parent all clocks under the PLL.
BCM5301X was the first platform on which that got noticed because of the
DT node unit name renaming but the same assumptions hold true for any
user of the iproc_pll_clk_setup() function.
The first 'clock-output-names' property is always guaranteed to be
unique as well as providing the actual desired PLL clock name, so we
utilize that to register the PLL and as a parent name of all children
clock.
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20220905161504.1526-1-f.fainelli@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1ff1bfe81 ]
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag
should not be used. For instance, the default parent clock for QSPI is
pll2_bus, which is also the parent clock for quite a few modules, such
as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system
hang due to pll2_bus rate changed.
Fixes: f1541e15e3 ("clk: imx6sx: Switch to clk_hw based API")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20220915150959.3646702-1-han.xu@nxp.com
Tested-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a91794ce8 ]
This splits of the setup part of the function setxattr in its own
dedicated function called setxattr_copy. In addition it also exposes a new
function called do_setxattr for making the setxattr call.
This makes it possible to call these two functions from io_uring in the
processing of an xattr request.
Signed-off-by: Stefan Roesch <shr@fb.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20220323154420.3301504-2-shr@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 06bbaa6dc5 ("[coredump] don't use __kernel_write() on kmap_local_page()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49725ffc15 ]
This commit fixes DMA engine reset timeout issue in suspend/resume
with ADLink I-Pi SMARC Plus board which dmesg shows:
...
[ 54.678271] PM: suspend exit
[ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL)
[ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0
...
[ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma
[ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed
[ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed
...
The issue is related with serdes which impacts clock. There is
serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to
commit b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
for detial. When issue is reproduced, DMA engine clock is not ready
because serdes is not powered up.
To reproduce DMA engine reset timeout issue with hardware which has
serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click
"Power Off/Log Out" -> "Suspend" menu, it disables network interface,
then goes to sleep mode. When it wakes up, it enables network
interface again. Stmmac driver is called in this way:
1. stmmac_release: Stop network interface. In this function, it
disables DMA engine and network interface;
2. stmmac_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into S3 or S0ix state. Some time later, system is
waken up by keyboard or mouse;
4. stmmac_resume: It does nothing because network interface has
been disabled;
5. stmmac_open: It is called to enable network interace again. DMA
engine is initialized in this API, but serdes is not power on so
there will be DMA engine reset timeout issue.
Similarly, serdes powerdown should be added in stmmac_release.
Network interface might be disabled by cmd "ifconfig eth0 down",
DMA engine, phy and mac have been disabled in ndo_stop callback,
serdes should be powered down as well. It doesn't make sense that
serdes is on while other components have been turned off.
If ethernet interface is in enabled state(netif_running(ndev) is true)
before suspend/resume, the issue couldn't be reproduced because serdes
could be powered up in stmmac_resume.
Because serdes_powerup is added in stmmac_open, it doesn't need to be
called in probe function.
Fixes: b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Jimmy JS Chen <jimmyjs.chen@adlinktech.com>
Tested-by: Looi, Hong Aun <hong.aun.looi@intel.com>
Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d873697ef2 ]
Commit 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
changed ieee80211_tx_control_port() to aways call
__ieee80211_select_queue() without checking local->hw.queues.
__ieee80211_select_queue() returns a queue-id between 0 and 3, which means
that now ieee80211_tx_control_port() may end up setting the queue-mapping
for a skb to a value higher then local->hw.queues if local->hw.queues
is less then 4.
Specifically this is a problem for ralink rt2500-pci cards where
local->hw.queues is 2. There this causes rt2x00queue_get_tx_queue() to
return NULL and the following error to be logged: "ieee80211 phy0:
rt2x00mac_tx: Error - Attempt to send packet over invalid queue 2",
after which association with the AP fails.
Other callers of __ieee80211_select_queue() skip calling it when
local->hw.queues < IEEE80211_NUM_ACS, add the same check to
ieee80211_tx_control_port(). This fixes ralink rt2500-pci and
similar cards when less then 4 tx-queues no longer working.
Fixes: 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
Cc: Markus Theil <markus.theil@tu-ilmenau.de>
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220918192052.443529-1-hdegoede@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c292a337d0 ]
The IOC_PR_CLEAR and IOC_PR_RELEASE ioctls are
non-functional on NVMe devices because the nvme_pr_clear()
and nvme_pr_release() functions set the IEKEY field incorrectly.
The IEKEY field should be set only when the key is zero (i.e,
not specified). The current code does it backwards.
Furthermore, the NVMe spec describes the persistent
reservation "clear" function as an option on the reservation
release command. The current implementation of nvme_pr_clear()
erroneously uses the reservation register command.
Fix these errors. Note that NVMe version 1.3 and later specify
that setting the IEKEY field will return an error of Invalid
Field in Command. The fix will set IEKEY when the key is zero,
which is appropriate as these ioctls consider a zero key to
be "unspecified", and the intention of the spec change is
to require a valid key.
Tested on a version 1.4 PCI NVMe device in an Azure VM.
Fixes: 1673f1f08c ("nvme: move block_device_operations and ns/ctrl freeing to common code")
Fixes: 1d277a637a ("NVMe: Add persistent reservation ops")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c635ebe8d9 ]
The label passed to the QDESC_GET for the ETHOFLD TXQ, RXQ, and FLQ, is the
'out' one, which skips the 'out_unlock' label, and thus doesn't unlock the
'uld_mutex' before returning. Additionally, since commit 5148e5950c
("cxgb4: add EOTID tracking and software context dump"), the access to
these ETHOFLD hardware queues should be protected by the 'mqprio_mutex'
instead.
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Fixes: 5148e5950c ("cxgb4: add EOTID tracking and software context dump")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Link: https://lore.kernel.org/r/20220922175109.764898-1-rafaelmendsr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4335417da2 ]
pwm support incompatible with Armada 80x0/70x0 API is not only in
Armada 370, but also in Armada XP, 38x and 39x. So basically every non-A8K
platform. Fix check for pwm support appropriately.
Fixes: 85b7d8abfe ("gpio: mvebu: add pwm support for Armada 8K/7K")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc62d98bd5 ]
This reverts commit 211f276ed3.
For quite some time, core DRM helpers already ensure that any relevant
connectors/CRTCs/etc. are disabled, as well as their associated
components (e.g., bridges) when suspending the system. Thus,
analogix_dp_bridge_{enable,disable}() already get called, which in turn
call drm_panel_{prepare,unprepare}(). This makes these drm_panel_*()
calls redundant.
Besides redundancy, there are a few problems with this handling:
(1) drm_panel_{prepare,unprepare}() are *not* reference-counted APIs and
are not in general designed to be handled by multiple callers --
although some panel drivers have a coarse 'prepared' flag that mitigates
some damage, at least. So at a minimum this is redundant and confusing,
but in some cases, this could be actively harmful.
(2) The error-handling is a bit non-standard. We ignored errors in
suspend(), but handled errors in resume(). And recently, people noticed
that the clk handling is unbalanced in error paths, and getting *that*
right is not actually trivial, given the current way errors are mostly
ignored.
(3) In the particular way analogix_dp_{suspend,resume}() get used (e.g.,
in rockchip_dp_*(), as a late/early callback), we don't necessarily have
a proper PM relationship between the DP/bridge device and the panel
device. So while the DP bridge gets resumed, the panel's parent device
(e.g., platform_device) may still be suspended, and so any prepare()
calls may fail.
So remove the superfluous, possibly-harmful suspend()/resume() handling
of panel state.
Fixes: 211f276ed3 ("drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time")
Link: https://lore.kernel.org/all/Yv2CPBD3Picg%2FgVe@google.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220822180729.1.I8ac5abe3a4c1c6fd5c061686c6e883c22f69022c@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49fad91a7b ]
Errors from debugfs are intended to be non-fatal, and should not prevent
the driver from probing.
Since debugfs file creation is treated as infallible, move it below the
parts of the probe function that can fail. This prevents an error
elsewhere in the probe function from causing the file to leak. Do the
same for the call to of_platform_populate().
Finally, checkpatch suggests an octal literal for the file permissions.
Fixes: 4af34b572a ("drivers: soc: sunxi: Introduce SoC driver to map SRAMs")
Fixes: 5828729beb ("soc: sunxi: export a regmap for EMAC clock reg on A64")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220815041248.53268-6-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a6d9ecff1 ]
Commit bcbb63b802 ("ARM: dts: dra7: Separate AM57 dtsi files")
disabled usb4_tm for am5748 devices since USB4 IP is not present
in this SoC.
The commit log explained the difference between AM5 and DRA7 families:
AM5 and DRA7 SoC families have different set of modules in them so the
SoC sepecific dtsi files need to be separated.
e.g. Some of the major differences between AM576 and DRA76
DRA76x AM576x
USB3 x
USB4 x
ATL x
VCP x
MLB x
ISS x
PRU-ICSS1 x
PRU-ICSS2 x
Then commit 176f26bcd4 ("ARM: dts: Add support for dra762 abz
package") removed usb4_tm part from am5748.dtsi and introcuded new
ti-sysc errors in dmesg:
ti-sysc 48940000.target-module: clock get error for fck: -2
ti-sysc: probe of 48940000.target-module failed with error -2
Fixes: 176f26bcd4 ("ARM: dts: Add support for dra762 abz package")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Message-Id: <20220823072742.351368-1-romain.naour@smile.fr>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 82806744fd upstream.
swiotlb_find_slots() skips slots according to io tlb aligned mask
calculated from min aligned mask and original physical address
offset. This affects max mapping size. The mapping size can't
achieve the IO_TLB_SEGSIZE * IO_TLB_SIZE when original offset is
non-zero. This will cause system boot up failure in Hyper-V
Isolation VM where swiotlb force is enabled. Scsi layer use return
value of dma_max_mapping_size() to set max segment size and it
finally calls swiotlb_max_mapping_size(). Hyper-V storage driver
sets min align mask to 4k - 1. Scsi layer may pass 256k length of
request buffer with 0~4k offset and Hyper-V storage driver can't
get swiotlb bounce buffer via DMA API. Swiotlb_find_slots() can't
find 256k length bounce buffer with offset. Make swiotlb_max_mapping
_size() take min align mask into account.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rishabh Bhatnagar <risbhat@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a99c44741 upstream.
Quite often, the HW get stuck in error condition if a stream error
was detected. As documented, the HW should stop immediately and self
reset. There is likely a problem or a miss-understanding of the self
reset mechanism, as unless we make a long pause, the next command
will then report an error even if there is no error in it.
Disabling error detection fixes the issue, and let the decoder continue
after an error. This patch is safe for backport into older kernels.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3723869907 upstream.
vb2_core_qbuf and vb2_core_querybuf don't check the range of b->index
controlled by the user.
Fix this by adding range checking code before using them.
Fixes: 57868acc36 ("media: videobuf2: Add new uAPI for DVB streaming I/O")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77677cdbc2 upstream.
The GHES code calls memory_failure_queue() from IRQ context to queue work
into workqueue and schedule it on the current CPU. Then the work is
processed in memory_failure_work_func() by kworker and calls
memory_failure().
When a page is already poisoned, commit a3f5d80ea4 ("mm,hwpoison: send
SIGBUS with error virutal address") make memory_failure() call
kill_accessing_process() that:
- holds mmap locking of current->mm
- does pagetable walk to find the error virtual address
- and sends SIGBUS to the current process with error info.
However, the mm of kworker is not valid, resulting in a null-pointer
dereference. So check mm when killing the accessing process.
[akpm@linux-foundation.org: remove unrelated whitespace alteration]
Link: https://lkml.kernel.org/r/20220914064935.7851-1-xueshuai@linux.alibaba.com
Fixes: a3f5d80ea4 ("mm,hwpoison: send SIGBUS with error virutal address")
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Bixuan Cui <cuibixuan@linux.alibaba.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac22531bb upstream.
A number of drivers call page_frag_alloc() with a fragment's size >
PAGE_SIZE.
In low memory conditions, __page_frag_cache_refill() may fail the order
3 cache allocation and fall back to order 0; In this case, the cache
will be smaller than the fragment, causing memory corruptions.
Prevent this from happening by checking if the newly allocated cache is
large enough for the fragment; if not, the allocation will fail and
page_frag_alloc() will return NULL.
Link: https://lkml.kernel.org/r/20220715125013.247085-1-mlombard@redhat.com
Fixes: b63ae8ca09 ("mm/net: Rename and move page fragment handling from net/ to mm/")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Cc: Chen Lin <chen45464546@163.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d36424b3b upstream.
Patrick Daly reported the following problem;
NODE_DATA(nid)->node_zonelists[ZONELIST_FALLBACK] - before offline operation
[0] - ZONE_MOVABLE
[1] - ZONE_NORMAL
[2] - NULL
For a GFP_KERNEL allocation, alloc_pages_slowpath() will save the
offset of ZONE_NORMAL in ac->preferred_zoneref. If a concurrent
memory_offline operation removes the last page from ZONE_MOVABLE,
build_all_zonelists() & build_zonerefs_node() will update
node_zonelists as shown below. Only populated zones are added.
NODE_DATA(nid)->node_zonelists[ZONELIST_FALLBACK] - after offline operation
[0] - ZONE_NORMAL
[1] - NULL
[2] - NULL
The race is simple -- page allocation could be in progress when a memory
hot-remove operation triggers a zonelist rebuild that removes zones. The
allocation request will still have a valid ac->preferred_zoneref that is
now pointing to NULL and triggers an OOM kill.
This problem probably always existed but may be slightly easier to trigger
due to 6aa303defb ("mm, vmscan: only allocate and reclaim from zones
with pages managed by the buddy allocator") which distinguishes between
zones that are completely unpopulated versus zones that have valid pages
not managed by the buddy allocator (e.g. reserved, memblock, ballooning
etc). Memory hotplug had multiple stages with timing considerations
around managed/present page updates, the zonelist rebuild and the zone
span updates. As David Hildenbrand puts it
memory offlining adjusts managed+present pages of the zone
essentially in one go. If after the adjustments, the zone is no
longer populated (present==0), we rebuild the zone lists.
Once that's done, we try shrinking the zone (start+spanned
pages) -- which results in zone_start_pfn == 0 if there are no
more pages. That happens *after* rebuilding the zonelists via
remove_pfn_range_from_zone().
The only requirement to fix the race is that a page allocation request
identifies when a zonelist rebuild has happened since the allocation
request started and no page has yet been allocated. Use a seqlock_t to
track zonelist updates with a lockless read-side of the zonelist and
protecting the rebuild and update of the counter with a spinlock.
[akpm@linux-foundation.org: make zonelist_update_seq static]
Link: https://lkml.kernel.org/r/20220824110900.vh674ltxmzb3proq@techsingularity.net
Fixes: 6aa303defb ("mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Patrick Daly <quic_pdaly@quicinc.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org> [4.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7afa79a3b upstream.
The block device uses multiple queues to access emmc. There will be up to 3
requests in the hsq of the host. The current code will check whether there
is a request doing recovery before entering the queue, but it will not check
whether there is a request when the lock is issued. The request is in recovery
mode. If there is a request in recovery, then a read and write request is
initiated at this time, and the conflict between the request and the recovery
request will cause the data to be trampled.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Fixes: 511ce378e1 ("mmc: Add MMC host software queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220916090506.10662-1-wenchao.chen666@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea08aec7e7 upstream.
Commit 1527f69204 ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).
The board_ahci_low_power configuration enables support for low power
modes.
This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.
Therefore, when commit 1527f69204 ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.
The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.
Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.
Fixes: 1527f69204 ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b7329cf5a upstream.
- Under SRIOV, we need to send REQ_GPU_FINI to the hypervisor
during the suspend time. Furthermore, we cannot request a
mode 1 reset under SRIOV as VF. Therefore, we will skip it
as it is called in suspend_noirq() function.
- In the resume code path, we need to send REQ_GPU_INIT to the
hypervisor and also resume PSP IP block under SRIOV.
Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
