[ Upstream commit bae8495381 ]
Differentiate between hardware not supporting hugepages and user disabling
THP via 'echo never > /sys/kernel/mm/transparent_hugepage/enabled'
For the devdax namespace, the kernel handles the above via the
supported_alignment attribute and failing to initialize the namespace if
the namespace align value is not supported on the platform.
For the fsdax namespace, the kernel will continue to initialize the
namespace. This can result in the kernel creating a huge pte entry even
though the hardware don't support the same.
We do want hugepage support with pmem even if the end-user disabled THP
via sysfs file (/sys/kernel/mm/transparent_hugepage/enabled). Hence
differentiate between hardware/firmware lacking support vs user-controlled
disable of THP and prevent a huge fault if the hardware lacks hugepage
support.
Link: https://lkml.kernel.org/r/20210205023956.417587-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deeaf96356 ]
For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecd6b010d8 ]
Testing mvuart->clk for non-error is not enough as mvuart->clk may contain
valid clk pointer but when clk_prepare_enable(mvuart->clk) failed then
port->uartclk is zero.
When mvuart->clk is not available then port->uartclk is zero too.
Parent clock rate port->uartclk is needed to calculate UART clock divisor
and without it is not possible to change baudrate.
So fix test condition when it is possible to change baudrate.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-3-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed78f56e12 ]
In case performance stats for an nvdimm are not available, reading the
'perf_stats' sysfs file returns an -ENOENT error. A better approach is
to make the 'perf_stats' file entirely invisible to indicate that
performance stats for an nvdimm are unavailable.
So this patch updates 'papr_nd_attribute_group' to add a 'is_visible'
callback implemented as newly introduced 'papr_nd_attribute_visible()'
that returns an appropriate mode in case performance stats aren't
supported in a given nvdimm.
Also the initialization of 'papr_scm_priv.stat_buffer_len' is moved
from papr_scm_nvdimm_init() to papr_scm_probe() so that it value is
available when 'papr_nd_attribute_visible()' is called during nvdimm
initialization.
Even though 'perf_stats' attribute is available since v5.9, there are
no known user-space tools/scripts that are dependent on presence of its
sysfs file. Hence I dont expect any user-space breakage with this
patch.
Fixes: 2d02bf835e ("powerpc/papr_scm: Fetch nvdimm performance stats from PHYP")
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210513092349.285021-1-vaibhav@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f35d2f249e ]
copy-paste contains implicit "copy buffer" state that can contain
arbitrary user data (if the user process executes a copy instruction).
This could be snooped by another process if a context switch hits while
the state is live. So cp_abort is executed on context switch to clear
out possible sensitive data and prevent the leak.
cp_abort is done after the low level _switch(), which means it is never
reached by newly created tasks, so they could snoop on this buffer
between their first and second context switch.
Fix this by doing the cp_abort before calling _switch. Add some
comments which should make the issue harder to miss.
Fixes: 07d2a628bc ("powerpc/64s: Avoid cpabort in context switch when possible")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210622053036.474678-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bab26238bb ]
printk_safe_flush_on_panic() has special lock breaking code for the case
where we panic()ed with the console lock held. It relies on panic IPI
causing other CPUs to mark themselves offline.
Do as most other architectures do.
This effectively reverts commit de6e5d3841 ("powerpc: smp_send_stop do
not offline stopped CPUs"), unfortunately it may result in some false
positive warnings, but the alternative is more situations where we can
crash without getting messages out.
Fixes: de6e5d3841 ("powerpc: smp_send_stop do not offline stopped CPUs")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623041245.865134-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b67e830d38 ]
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 439c7183e5 ]
UARTs on TI SoCs prior to J7200 don't provide independent control over
RX FIFO not empty interrupt (RHR_IT) and RX timeout interrupt.
Starting with J7200 SoC, its possible to disable RHR_IT independent of
RX timeout interrupt using bit 2 of IER2 register. So disable RHR_IT
once RX DMA is started so as to avoid spurious interrupt being raised
when data is in the RX FIFO but is yet to be drained by DMA (a known
errata in older SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201029051930.7097-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07b60713b5 ]
When running event-no-pid test on small machines (e.g. cloud 1-core
instance), other events might not happen:
+ cat trace
+ cnt=0
+ [ 0 -eq 0 ]
+ fail No other events were recorded
[15] event tracing - restricts events based on pid notrace filtering [FAIL]
Schedule a simple sleep task to be sure that some other process events
get recorded.
Fixes: ebed9628f5 ("selftests/ftrace: Add test to test new set_event_notrace_pid file")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee78b9360e ]
In 'ktd2692_parse_dt()', if an error occurs after a successful
'regulator_enable()' call, we should call 'regulator_enable()'.
This is the same in 'ktd2692_probe()', if an error occurs after a
successful 'ktd2692_parse_dt()' call.
Instead of adding 'regulator_enable()' in several places, implement a
resource managed solution and simplify the remove function accordingly.
Fixes: b7da8c5c72 ("leds: Add ktd2692 flash LED driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7a0a2feb9 ]
When system enter suspend, the machine driver suspend callback
function will be called, then the cpu driver trigger callback
(SNDRV_PCM_TRIGGER_SUSPEND) be called, it would disable the
interrupt.
But the machine driver suspend and cpu dai driver suspend order
maybe changed, the cpu dai driver's suspend callback is called before
machine driver's suppend callback, then the interrupt is not cleared
successfully in trigger callback.
So need to clear interrupts in cpu dai driver's suspend callback
to avoid such issue.
Fixes: 9cb2b3796e ("ASoC: fsl_spdif: Add pm runtime function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1624365084-7934-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c252b087d ]
When reading binary attributes in progress, buffer->bin_buffer is setup in
configfs_read_bin_file() but never freed.
Fixes: 03607ace80 ("configfs: implement binary attributes")
Signed-off-by: Chung-Chiang Cheng <cccheng@synology.com>
[hch: move the vfree rather than duplicating it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3729e0ec59 ]
POWER9 and POWER10 asynchronous machine checks due to stores have their
cause reported in SRR1 but SRR1[42] is set, which in other cases
indicates DSISR cause.
Check for these cases and clear SRR1[42], so the cause matching uses
the i-side (SRR1) table.
Fixes: 7b9f71f974 ("powerpc/64s: POWER9 machine check handler")
Fixes: 201220bb0e ("powerpc/powernv: Machine check handler for POWER10")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210517140355.2325406-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc11fc2991 ]
The platform device driver name is "max8997-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: b76668ba8a ("Extcon: add MAX8997 extcon driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d25b224f8e ]
When sm5502_init_dev_type() iterates over sm5502_reg_data to
initialize the registers it is limited by ARRAY_SIZE(sm5502_reg_data).
There is no need to add another empty element to sm5502_reg_data.
Having the additional empty element in sm5502_reg_data will just
result in writing 0xff to register 0x00, which does not really
make sense.
Fixes: 914b881f94 ("extcon: sm5502: Add support new SM5502 extcon device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a90bbb478 ]
The current driver uses a value from register TEST_O as the original
value for register TEST_I, though, the value is overwritten by "param",
so there is a bug that the original value isn't no longer used.
The value of TEST_O[7:0] should be masked with "mask", replaced with
"param", and placed in the bitfield TESTI_DAT_MASK as new TEST_I value.
Fixes: c6d9b13241 ("phy: socionext: add PCIe PHY driver support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1623037842-19363-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3e88e336 ]
In sdw_prep_deprep_slave_ports(), after the wait_for_completion()
the DP prepare status register is read. If this indicates that the
port is now prepared, the code should continue with the port setup.
It is irrelevant whether the wait_for_completion() timed out if the
port is now ready.
The previous implementation would always fail if the
wait_for_completion() timed out, even if the port was reporting
successful prepare.
This patch also fixes a minor bug where the return from sdw_read()
was not checked for error - any error code with LSBits clear could
be misinterpreted as a successful port prepare.
Fixes: 79df15b7d3 ("soundwire: Add helpers for ports operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210618144745.30629-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3002f467a0 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 2e5eda4681 ("habanalabs: PCIe Advanced Error Reporting support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2892d8a00d ]
Variable "size" has type "phys_addr_t", which can be either 32-bit or
64-bit on 32-bit systems, while "unsigned long" is always 32-bit on
32-bit systems. Hence the cast in
(unsigned long)size / SZ_1M
may truncate a 64-bit size to 32-bit, as casts have a higher operator
precedence than divisions.
Fix this by inverting the order of the cast and division, which should
be safe for memory blocks smaller than 4 PiB. Note that the division is
actually a shift, as SZ_1M is a power-of-two constant, hence there is no
need to use div_u64().
While at it, use "%lu" to format "unsigned long".
Fixes: e8d9d1f548 ("drivers: of: add initialization code for static reserved memory")
Fixes: 3f0c820664 ("drivers: of: add initialization code for dynamic reserved memory")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/4a1117e72d13d26126f57be034c20dac02f1e915.1623835273.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92babc9938 ]
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Fixes: 1c28799257 ("iio: light: isl29501: Add support for the ISL29501 ToF sensor.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-9-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec90b52c07 ]
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a potential
kernel data leak, making for a less minimal fix.
Fixes: 55707294c4 ("iio: light: Add support for vishay vcnl4035")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-8-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78bcae8616 ]
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b4f167ef3 ]
Driver code call 'devm_of_pci_get_host_bridge_resources'
to get resources and properly fill 'bridge->windows' and
'bridge->dma_ranges'. After parsing the ranges and store
as resources, at the end it makes a call to pci function
'pci_add_resource_offset' to set the offset for the
memory resource. To calculate offset, resource start address
subtracts pci address of the range. MT7621 does not need
any offset for the memory resource. Moreover, setting an
offset got into 'WARN_ON' calls from pci devices driver code.
Until now memory range pci_addr was being '0x00000000' and
res->start is '0x60000000' but becase pci controller driver
was manually setting resources and adding them using pci function
'pci_add_resource' where a zero is passed as offset, things
was properly working. Since PCI_IOBASE is defined now for
ralink we don't set nothing manually anymore so we have to
properly fix PCI address for this range to make things work
and the new pci address must be set to '0x60000000'. Doing
in this way the subtract result obtain zero as offset
and pci device driver code properly works.
Fixes: d59578da2b ("staging: mt7621-dts: add dts files")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210614100617.28753-4-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e02a3b9458 ]
There is a leak in rtl8712 driver.
The problem was in non-freed adapter data if
firmware load failed.
This leak can be reproduced with this code:
https://syzkaller.appspot.com/text?tag=ReproC&x=16612f02d00000,
Autoload must fail (to not hit memory leak reported by syzkaller)
There are 2 possible ways how rtl871x_load_fw_cb() and
r871xu_dev_remove() can be called (in case of fw load error).
1st case:
r871xu_dev_remove() then rtl871x_load_fw_cb()
In this case r871xu_dev_remove() will wait for
completion and then will jump to the end, because
rtl871x_load_fw_cb() set intfdata to NULL:
if (pnetdev) {
struct _adapter *padapter = netdev_priv(pnetdev);
/* never exit with a firmware callback pending */
wait_for_completion(&padapter->rtl8712_fw_ready);
pnetdev = usb_get_intfdata(pusb_intf);
usb_set_intfdata(pusb_intf, NULL);
if (!pnetdev)
goto firmware_load_fail;
... clean up code here ...
}
2nd case:
rtl871x_load_fw_cb() then r871xu_dev_remove()
In this case pnetdev (from code snippet above) will
be zero (because rtl871x_load_fw_cb() set it to NULL)
And clean up code won't be executed again.
So, in all cases we need to free adapted data in rtl871x_load_fw_cb(),
because disconnect function cannot take care of it. And there won't be
any race conditions, because complete() call happens after setting
intfdata to NULL.
In previous patch I moved out free_netdev() from r8712_free_drv_sw()
and that's why now it's possible to free adapter data and then call
complete.
Fixes: 8c213fa591 ("staging: r8712u: Use asynchronous firmware loading")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/81e68fe0194499cc2e7692d35bc4dcf167827d8f.1623620630.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce793c0ab ]
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Found during an audit of all callers of iio_push_to_buffers_with_timestamp()
Fixes: 8fe78d5261 ("iio: vcnl4000: Add buffer support for VCNL4010/20.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-7-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
