commit 2bed8a8e70 upstream.
When in RS485 emulation mode, __do_stop_tx_rs485() calls
serial8250_clear_fifos(). This not only clears the FIFOs, but also sets
all bits in their control register (UART_FCR) to 0.
One of the effects of this is the disabling of the FIFOs, which turns
them into single-byte holding registers. The rest of the driver doesn't
know this, which results in the lions share of characters passed into a
write call to be dropped.
(I can supply logic analyzer screenshots if necessary)
This fix replaces the serial8250_clear_fifos() call to
serial8250_clear_and_reinit_fifos() - this prevents the "dropped
characters" issue from manifesting again while retaining the requirement
of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX
flag is disabled.
Signed-off-by: Daniel Jedrychowski <avistel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b11ebedd6 upstream.
Function get_zeroed_page() returns a NULL pointer if there is no enough
memory. In function extcon_sync(), it returns 0 if the call to
get_zeroed_page() fails. The return value 0 indicates success in the
context, which is incosistent with the execution status. This patch
fixes the bug by returning -ENOMEM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188611
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: a580982f08
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 802c03881f upstream.
The sysrq input handler should be attached to the input device which has
a left alt key.
On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler. Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.
I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 570b90fa23 upstream.
Eric Biggers pointed out that the orinoco driver pointed scatterlists
at the stack.
Fix it by switching from ahash to shash. The result should be
simpler, faster, and more correct.
kvalo: cherry picked from commit 1fef293b8a as I
accidentally applied this patch to wireless-drivers-next when I was supposed to
apply this wireless-drivers
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c9d8d0c41 upstream.
If srp_transfer_data fails within ibmvscsis_write_pending, then
the most likely scenario is that the client timed out the op and
removed the TCE mapping. Thus it will loop forever retrying the
op that is pretty much guaranteed to fail forever. A better return
code would be EIO instead of EAGAIN.
Reported-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bgly@us.ibm.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89d8232411 upstream.
If we don't disable the transmitter in atmel_stop_tx, the DMA buffer
continues to send data until it is emptied.
This cause problems with the flow control (CTS is asserted and data are
still sent).
So, disabling the transmitter in atmel_stop_tx is a sane thing to do.
Tested on at91sam9g35-cm(DMA)
Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b389f173aa upstream.
When using RS485 in half duplex, RX should be enabled when TX is
finished, and stopped when TX starts.
Before commit 0058f0871e ("tty/serial: atmel: fix RS485 half
duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA
was used. So, collisions could happened.
But disabling RX in atmel_start_tx() uncovered another bug:
RX was enabled again in the wrong place (in atmel_tx_dma) instead of
being enabled when TX is finished (in atmel_complete_tx_dma), so the
transmission simply stopped.
This bug was not triggered before commit 0058f0871e
("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was
never disabled before.
Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem.
Reported-by: Gil Weber <webergil@gmail.com>
Fixes: 0058f0871e
Tested-by: Gil Weber <webergil@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a14d749fce upstream.
Most users of BLOCK_PC requests allocate the sense buffer on the stack,
so to avoid DMA to the stack copy them to a field in the heap allocated
virtblk_req structure. Without that any attempt at SCSI passthrough I/O,
including the SG_IO ioctl from userspace will crash the kernel. Note that
this includes running tools like hdparm even when the host does not have
SCSI passthrough enabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 836c3ce256 upstream.
The original patch did not done what it was supposed to be doing and even
worst it broke legacy boot (OMAP1).
The lch_map size should be the number of available logical channels in sDMA
and the od->dma_requests should store the number of available DMA request
lines usable in sDMA.
In legacy mode we do not have a way to get the DMA request count, in that
case we use OMAP_SDMA_REQUESTS (127), despite the fact that OMAP1510 have
only 31 DMA request line.
Fixes: 2d1a9a946f ("dmaengine: omap-dma: Dynamically allocate memory for lch_map")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 488debb997 upstream.
When borrowing the pfn_valid() check from mmap_kmem(), somebody managed
to get physical and virtual addresses spectacularly muddled up, such
that we've ended up with checks for one being the other. Whilst this
does indeed prevent out-of-bounds accesses crashing, on most systems
it also prevents the more desirable use-case of working at all ever.
Check the *virtual* offset correctly for what it is. Furthermore, do
so in the right place - a read or write may span multiple pages, so a
single up-front check is insufficient. High memory accesses already
have a similar validity check just before the copy_to_user() call, so
just make the low memory path fully consistent with that.
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 148a1bc843 ("drivers: char: mem: Check {read,write}_kmem() addresses")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3895dbf898 upstream.
Protecting the mountpoint hashtable with namespace_sem was sufficient
until a call to umount_mnt was added to mntput_no_expire. At which
point it became possible for multiple calls of put_mountpoint on
the same hash chain to happen on the same time.
Kristen Johansen <kjlx@templeofstupid.com> reported:
> This can cause a panic when simultaneous callers of put_mountpoint
> attempt to free the same mountpoint. This occurs because some callers
> hold the mount_hash_lock, while others hold the namespace lock. Some
> even hold both.
>
> In this submitter's case, the panic manifested itself as a GP fault in
> put_mountpoint() when it called hlist_del() and attempted to dereference
> a m_hash.pprev that had been poisioned by another thread.
Al Viro observed that the simple fix is to switch from using the namespace_sem
to the mount_lock to protect the mountpoint hash table.
I have taken Al's suggested patch moved put_mountpoint in pivot_root
(instead of taking mount_lock an additional time), and have replaced
new_mountpoint with get_mountpoint a function that does the hash table
lookup and addition under the mount_lock. The introduction of get_mounptoint
ensures that only the mount_lock is needed to manipulate the mountpoint
hashtable.
d_set_mounted is modified to only set DCACHE_MOUNTED if it is not
already set. This allows get_mountpoint to use the setting of
DCACHE_MOUNTED to ensure adding a struct mountpoint for a dentry
happens exactly once.
Fixes: ce07d891a0 ("mnt: Honor MNT_LOCKED when detaching mounts")
Reported-by: Krister Johansen <kjlx@templeofstupid.com>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit add7c65ca4 upstream.
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
4.10.0-rc2-00024-g4aecec9-dirty #118 Tainted: G W
---------------------------------------------------------
swapper/1/0 just changed the state of lock:
(&(&sighand->siglock)->rlock){-.....}, at: [<ffffffffbd0a1bc6>] __lock_task_sighand+0xb6/0x2c0
but this lock took another, HARDIRQ-unsafe lock in the past:
(ucounts_lock){+.+...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Chain exists of: &(&sighand->siglock)->rlock --> &(&tty->ctrl_lock)->rlock --> ucounts_lock
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(ucounts_lock);
local_irq_disable();
lock(&(&sighand->siglock)->rlock);
lock(&(&tty->ctrl_lock)->rlock);
<Interrupt>
lock(&(&sighand->siglock)->rlock);
*** DEADLOCK ***
This patch removes a dependency between rlock and ucount_lock.
Fixes: f333c700c6 ("pidns: Add a limit on the number of pid namespaces")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8a6a09c1c upstream.
In ca91cx42_slave_get function, the value pointed by vme_base pointer is
set through:
*vme_base = ioread32(bridge->base + CA91CX42_VSI_BS[i]);
So it must be dereferenced to be used in calculation of pci_base:
*pci_base = (dma_addr_t)*vme_base + pci_offset;
This bug was caught thanks to the following gcc warning:
drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’:
drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
*pci_base = (dma_addr_t)vme_base + pci_offset;
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-By: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6741f551a0 upstream.
This commit needs to be reverted because it prevents people from
using the serial console as a secondary console with input being
directed to tty0.
IOW, if you boot with console=ttyS0 console=tty0 then all kernels
prior to this commit will produce output on both ttyS0 and tty0
but input will only be taken from tty0. With this patch the serial
console will always be the primary console instead of tty0,
potentially preventing people from getting into their machines in
emergency situations.
Fixes: d03516df83 ("tty: serial: 8250: add CON_CONSDEV to flags")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e4d59ada4 upstream.
This is a fix for Linux 4.10-rc1.
In C language specification, a bit-field is interpreted as a signed or
unsigned integer type consisting of the specified number of bits.
In GCC manual, the range of a signed bit field of N bits is from
-(2^N) / 2 to ((2^N) / 2) - 1
https://www.gnu.org/software/gnu-c-manual/gnu-c-manual.html#Bit-Fields
Therefore, when defined as 1 bit-field with signed type, variables can
represents -1 and 0.
The snd-soc-hdmi-codec module includes a structure which has signed type
members with bit-fields. Codes of this module assign 0 and 1 to the
members. This seems to result in implementation-dependent behaviours.
As of v4.10-rc1 merge window, outside of sound subsystem, this structure
is referred by below GPU modules.
- tda998x
- sti-drm
- mediatek-drm-hdmi
- msm
As long as I review their codes relevant to the structure, the structure
members are used just for condition statements and printk formats.
My proposal of change is a bit intrusive to the printk formats but this
may be acceptable.
Totally, it's reasonable to use unsigned type for the structure members.
This bug is detected by Sparse, static code analyzer with below warnings.
./include/sound/hdmi-codec.h:39:26: error: dubious one-bit signed bitfield
./include/sound/hdmi-codec.h:40:28: error: dubious one-bit signed bitfield
./include/sound/hdmi-codec.h:41:29: error: dubious one-bit signed bitfield
./include/sound/hdmi-codec.h:42:31: error: dubious one-bit signed bitfield
Fixes: 09184118a8 ("ASoC: hdmi-codec: Add hdmi-codec for external HDMI-encoders")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac0c7cf8be upstream.
Enabling btrfs tracepoints leads to instant crash, as reported. The wq
callbacks could free the memory and the tracepoints started to
dereference the members to get to fs_info.
The proposed fix https://marc.info/?l=linux-btrfs&m=148172436722606&w=2
removed the tracepoints but we could preserve them by passing only the
required data in a safe way.
Fixes: bc074524e1 ("btrfs: prefix fsid to all trace events")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6169d0409 upstream.
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9dc6f65bc upstream.
The logics in pipe_advance() used to release all buffers past the new
position failed in cases when the number of buffers to release was equal
to pipe->buffers. If that happened, none of them had been released,
leaving pipe full. Worse, it was trivial to trigger and we end up with
pipe full of uninitialized pages. IOW, it's an infoleak.
Reported-by: "Alan J. Wylie" <alan@wylie.me.uk>
Tested-by: "Alan J. Wylie" <alan@wylie.me.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30f939feae upstream.
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f724fb303 upstream.
In of_i2c_register_device(), when the check for
device address validity fails we print the info.addr,
which has not been assigned properly.
Fix this by printing the actual invalid address.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: b4e2f6ac12 ("i2c: apply DT flags when probing")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a20047f36e upstream.
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a ("USB: ch341: set tty baud speed according to tty struct")
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d5a9c72d0 upstream.
A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.
Check for short transfers, and make sure to log any transfer errors.
Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).
Fixes: 6ce7610478 ("USB: Driver for CH341 USB-serial adaptor")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2950b7854 upstream.
Make sure to stop the interrupt URB before returning on errors during
open.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce5e292828 upstream.
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after resume")
Fixes: 2bfd1c96a9 ("USB: serial: ch341: remove reset_resume callback")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e2da44691 upstream.
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 146cc8a17a upstream.
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Fixes: abf492e7b3 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b6c1b4c0e upstream.
MUSB driver now has runtime PM support, but the debugfs driver misses
the PM _get/_put() calls, which could cause MUSB register access
failure.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 620f1a632e upstream.
The driver put a constant buffer of all zeros on the stack and
pointed a scatterlist entry at it. This doesn't work with virtual
stacks. Use ZERO_PAGE instead.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3344ed3079 upstream.
The workaround for the AMD Erratum E400 (Local APIC timer stops in C1E
state) is a two step process:
- Selection of the E400 aware idle routine
- Detection whether the platform is affected
The idle routine selection happens for possibly affected CPUs depending on
family/model/stepping information. These range of CPUs is not necessarily
affected as the decision whether to enable the C1E feature is made by the
firmware. Unfortunately there is no way to query this at early boot.
The current implementation polls a MSR in the E400 aware idle routine to
detect whether the CPU is affected. This is inefficient on non affected
CPUs because every idle entry has to do the MSR read.
There is a better way to detect this before going idle for the first time
which requires to seperate the bug flags:
X86_BUG_AMD_E400 - Selects the E400 aware idle routine and
enables the detection
X86_BUG_AMD_APIC_C1E - Set when the platform is affected by E400
Replace the current X86_BUG_AMD_APIC_C1E usage by the new X86_BUG_AMD_E400
bug bit to select the idle routine which currently does an unconditional
detection poll. X86_BUG_AMD_APIC_C1E is going to be used in later patches
to remove the MSR polling and simplify the handling of this misfeature.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-3-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6a50cddbc upstream.
These changes do not affect current hw - just a cleanup:
Currently, we assume that a system has a single Last Level Cache (LLC)
per node, and that the cpu_llc_id is thus equal to the node_id. This no
longer applies since Fam17h can have multiple last level caches within a
node.
So group the cpu_llc_id assignment by topology feature and family in
order to make the computation of cpu_llc_id on the different families
more clear.
Here is how the LLC ID is being computed on the different families:
The NODEID_MSR feature only applies to Fam10h in which case the LLC is
at the node level.
The TOPOEXT feature is used on families 15h, 16h and 17h. So far we only
see multiple last level caches if L3 caches are available. Otherwise,
the cpu_llc_id will default to be the phys_proc_id.
We have L3 caches only on families 15h and 17h:
- on Fam15h, the LLC is at the node level.
- on Fam17h, the LLC is at the core complex level and can be found by
right shifting the APIC ID. Also, keep the family checks explicit so that
new families will fall back to the default, which will be node_id for
TOPOEXT systems.
Single node systems in families 10h and 15h will have a Node ID of 0
which will be the same as the phys_proc_id, so we don't need to check
for multiple nodes before using the node_id.
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
[ Rewrote the commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161108153054.bs3sajbyevq6a6uu@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14221cc45c upstream.
Problem:
br_nf_pre_routing_finish() calls itself instead of
br_nf_pre_routing_finish_bridge(). Due to this bug reverse path filter drops
packets that go through bridge interface.
User impact:
Local docker containers with bridge network can not communicate with each
other.
Fixes: c5136b15ea ("netfilter: bridge: add and use br_nf_hook_thresh")
Signed-off-by: Artur Molchanov <artur.molchanov@synesis.ru>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a417b8dc1 upstream.
Commit 99579ccec4 "xfs: skip dirty pages in ->releasepage()" started
to skip dirty pages in xfs_vm_releasepage() which also has the effect
that if a dirty page is truncated, it does not get freed by
block_invalidatepage() and is lingering in LRU list waiting for reclaim.
So a simple loop like:
while true; do
dd if=/dev/zero of=file bs=1M count=100
rm file
done
will keep using more and more memory until we hit low watermarks and
start pagecache reclaim which will eventually reclaim also the truncate
pages. Keeping these truncated (and thus never usable) pages in memory
is just a waste of memory, is unnecessarily stressing page cache
reclaim, and reportedly also leads to anonymous mmap(2) returning ENOMEM
prematurely.
So instead of just skipping dirty pages in xfs_vm_releasepage(), return
to old behavior of skipping them only if they have delalloc or unwritten
buffers and fix the spurious warnings by warning only if the page is
clean.
CC: Brian Foster <bfoster@redhat.com>
CC: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Petr Tůma <petr.tuma@d3s.mff.cuni.cz>
Fixes: 99579ccec4
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5018ada69a upstream.
When removing a gpiochip that uses GPIO hogging (e.g. by unloading the
chip's DT overlay), a warning is printed:
gpio gpiochip8: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
This happens because gpiochip_free_hogs() is called after the gdev->chip
pointer is reset to NULL. Hence __gpiod_free() cannot determine the
chip in use, and cannot clear flags nor call the optional chip-specific
.free() callback.
Move the call to gpiochip_free_hogs() up to fix this.
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 753aacfd2e upstream.
A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.
Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.
Fixes: 93a1e86ce1 ("nl80211: Stop scheduled scan if netlink client disappears")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20b1e22d01 upstream.
With the following commit:
4bc9f92e64 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
... efi_bgrt_init() calls into the memblock allocator through
efi_mem_reserve() => efi_arch_mem_reserve() *after* mm_init() has been called.
Indeed, KASAN reports a bad read access later on in efi_free_boot_services():
BUG: KASAN: use-after-free in efi_free_boot_services+0xae/0x24c
at addr ffff88022de12740
Read of size 4 by task swapper/0/0
page:ffffea0008b78480 count:0 mapcount:-127
mapping: (null) index:0x1 flags: 0x5fff8000000000()
[...]
Call Trace:
dump_stack+0x68/0x9f
kasan_report_error+0x4c8/0x500
kasan_report+0x58/0x60
__asan_load4+0x61/0x80
efi_free_boot_services+0xae/0x24c
start_kernel+0x527/0x562
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x157/0x17a
start_cpu+0x5/0x14
The instruction at the given address is the first read from the memmap's
memory, i.e. the read of md->type in efi_free_boot_services().
Note that the writes earlier in efi_arch_mem_reserve() don't splat because
they're done through early_memremap()ed addresses.
So, after memblock is gone, allocations should be done through the "normal"
page allocator. Introduce a helper, efi_memmap_alloc() for this. Use
it from efi_arch_mem_reserve(), efi_free_boot_services() and, for the sake
of consistency, from efi_fake_memmap() as well.
Note that for the latter, the memmap allocations cease to be page aligned.
This isn't needed though.
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 4bc9f92e64 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
Link: http://lkml.kernel.org/r/20170105125130.2815-1-nicstange@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0100a3e67a upstream.
Some machines, such as the Lenovo ThinkPad W541 with firmware GNET80WW
(2.28), include memory map entries with phys_addr=0x0 and num_pages=0.
These machines fail to boot after the following commit,
commit 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Fix this by removing such bogus entries from the memory map.
Furthermore, currently the log output for this case (with efi=debug)
looks like:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[0x0000000000000000-0xffffffffffffffff] (0MB)
This is clearly wrong, and also not as informative as it could be. This
patch changes it so that if we find obviously invalid memory map
entries, we print an error and skip those entries. It also detects the
display of the address range calculation overflow, so the new output is:
[ 0.000000] efi: [Firmware Bug]: Invalid EFI memory map entries:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[0x0000000000000000-0x0000000000000000] (invalid)
It also detects memory map sizes that would overflow the physical
address, for example phys_addr=0xfffffffffffff000 and
num_pages=0x0200000000000001, and prints:
[ 0.000000] efi: [Firmware Bug]: Invalid EFI memory map entries:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[phys_addr=0xfffffffffffff000-0x20ffffffffffffffff] (invalid)
It then removes these entries from the memory map.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[ardb: refactor for clarity with no functional changes, avoid PAGE_SHIFT]
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
[Matt: Include bugzilla info in commit log]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191121
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 129a72a0d3 upstream.
Introduces segemented_write_std.
Switches from emulated reads/writes to standard read/writes in fxsave,
fxrstor, sgdt, and sidt. This fixes CVE-2017-2584, a longstanding
kernel memory leak.
Since commit 283c95d0e3 ("KVM: x86: emulate FXSAVE and FXRSTOR",
2016-11-09), which is luckily not yet in any final release, this would
also be an exploitable kernel memory *write*!
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 96051572c8
Fixes: 283c95d0e3
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 283c95d0e3 upstream.
Internal errors were reported on 16 bit fxsave and fxrstor with ipxe.
Old Intels don't have unrestricted_guest, so we have to emulate them.
The patch takes advantage of the hardware implementation.
AMD and Intel differ in saving and restoring other fields in first 32
bytes. A test wrote 0xff to the fxsave area, 0 to upper bits of MCSXR
in the fxsave area, executed fxrstor, rewrote the fxsave area to 0xee,
and executed fxsave:
Intel (Nehalem):
7f 1f 7f 7f ff 00 ff 07 ff ff ff ff ff ff 00 00
ff ff ff ff ff ff 00 00 ff ff 00 00 ff ff 00 00
Intel (Haswell -- deprecated FPU CS and FPU DS):
7f 1f 7f 7f ff 00 ff 07 ff ff ff ff 00 00 00 00
ff ff ff ff 00 00 00 00 ff ff 00 00 ff ff 00 00
AMD (Opteron 2300-series):
7f 1f 7f 7f ff 00 ee ee ee ee ee ee ee ee ee ee
ee ee ee ee ee ee ee ee ff ff 00 00 ff ff 02 00
fxsave/fxrstor will only be emulated on early Intels, so KVM can't do
much to improve the situation.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aabba3c6ab upstream.
Move the existing exception handling for inline assembly into a macro
and switch its return values to X86EMUL type.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cef84c302f upstream.
KVM's lapic emulation uses static_key_deferred (apic_{hw,sw}_disabled).
These are implemented with delayed_work structs which can still be
pending when the KVM module is unloaded. We've seen this cause kernel
panics when the kvm_intel module is quickly reloaded.
Use the new static_key_deferred_flush() API to flush pending updates on
module unload.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6416e6101 upstream.
Modules that use static_key_deferred need a way to synchronize with
any delayed work that is still pending when the module is unloaded.
Introduce static_key_deferred_flush() which flushes any pending
jump label updates.
Signed-off-by: David Matlack <dmatlack@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f3dbdf47e upstream.
Reported syzkaller:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: irq_bypass_unregister_consumer+0x9d/0xb70 [irqbypass]
PGD 0
Oops: 0002 [#1] SMP
CPU: 1 PID: 125 Comm: kworker/1:1 Not tainted 4.9.0+ #1
Workqueue: kvm-irqfd-cleanup irqfd_shutdown [kvm]
task: ffff9bbe0dfbb900 task.stack: ffffb61802014000
RIP: 0010:irq_bypass_unregister_consumer+0x9d/0xb70 [irqbypass]
Call Trace:
irqfd_shutdown+0x66/0xa0 [kvm]
process_one_work+0x16b/0x480
worker_thread+0x4b/0x500
kthread+0x101/0x140
? process_one_work+0x480/0x480
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x25/0x30
RIP: irq_bypass_unregister_consumer+0x9d/0xb70 [irqbypass] RSP: ffffb61802017e20
CR2: 0000000000000008
The syzkaller folks reported a NULL pointer dereference that due to
unregister an consumer which fails registration before. The syzkaller
creates two VMs w/ an equal eventfd occasionally. So the second VM
fails to register an irqbypass consumer. It will make irqfd as inactive
and queue an workqueue work to shutdown irqfd and unregister the irqbypass
consumer when eventfd is closed. However, the second consumer has been
initialized though it fails registration. So the token(same as the first
VM's) is taken to unregister the consumer through the workqueue, the
consumer of the first VM is found and unregistered, then NULL deref incurred
in the path of deleting consumer from the consumers list.
This patch fixes it by making irq_bypass_register/unregister_consumer()
looks for the consumer entry based on consumer pointer itself instead of
token matching.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33ab91103b upstream.
This is CVE-2017-2583. On Intel this causes a failed vmentry because
SS's type is neither 3 nor 7 (even though the manual says this check is
only done for usable SS, and the dmesg splat says that SS is unusable!).
On AMD it's worse: svm.c is confused and sets CPL to 0 in the vmcb.
The fix fabricates a data segment descriptor when SS is set to a null
selector, so that CPL and SS.DPL are set correctly in the VMCS/vmcb.
Furthermore, only allow setting SS to a NULL selector if SS.RPL < 3;
this in turn ensures CPL < 3 because RPL must be equal to CPL.
Thanks to Andy Lutomirski and Willy Tarreau for help in analyzing
the bug and deciphering the manuals.
Reported-by: Xiaohan Zhang <zhangxiaohan1@huawei.com>
Fixes: 79d5b4c3cd
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5bbc8a6c9 upstream.
return_unused_surplus_pages() decrements the global reservation count,
and frees any unused surplus pages that were backing the reservation.
Commit 7848a4bf51 ("mm/hugetlb.c: add cond_resched_lock() in
return_unused_surplus_pages()") added a call to cond_resched_lock in the
loop freeing the pages.
As a result, the hugetlb_lock could be dropped, and someone else could
use the pages that will be freed in subsequent iterations of the loop.
This could result in inconsistent global hugetlb page state, application
api failures (such as mmap) failures or application crashes.
When dropping the lock in return_unused_surplus_pages, make sure that
the global reservation count (resv_huge_pages) remains sufficiently
large to prevent someone else from claiming pages about to be freed.
Analyzed by Paul Cassella.
Fixes: 7848a4bf51 ("mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()")
Link: http://lkml.kernel.org/r/1483991767-6879-1-git-send-email-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Paul Cassella <cassella@cray.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
