[ Upstream commit 735f5ae49e ]
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 805dfc18dd ]
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e62ad74aa5 ]
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b205f58502 ]
Some resource should be released if an error occurs in
'bcm2835_i2c_probe()'.
Add an error handling path and the needed 'clk_disable_unprepare()' and
'clk_rate_exclusive_put()' calls.
While at it, rework the bottom of the function to use this newly added
error handling path and have an explicit and more standard "return 0;" at
the end of the normal path.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[wsa: rebased]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3b2f911ac ]
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 920a9fa27e ]
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 585d42bb57 ]
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfcbb76b0f ]
When unregistering a physical clock which has some virtual clocks,
unregister the virtual clocks with it.
This fixes the following oops, which can be triggered by unloading
a driver providing a PTP clock when it has enabled virtual clocks:
BUG: unable to handle page fault for address: ffffffffc04fc4d8
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ptp_vclock_read+0x31/0xb0
Call Trace:
timecounter_read+0xf/0x50
ptp_vclock_refresh+0x2c/0x50
? ptp_clock_release+0x40/0x40
ptp_aux_kworker+0x17/0x30
kthread_worker_fn+0x9b/0x240
? kthread_should_park+0x30/0x30
kthread+0xe2/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
Fixes: 73f37068d5 ("ptp: support ptp physical/virtual clocks conversion")
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8e2c707c ]
Check sta_rates pointer value in mt7603_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42ce8d3b62 ]
Fix a possible race in mt7615_pm_power_save_work() if rx/tx napi
schedules ps_work and we are currently accessing device register
on a different cpu.
Fixes: db928f1ab9 ("mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 591cdccebd ]
Fix a possible race in mt7921_pm_power_save_work() if rx/tx napi
schedules ps_work and we are currently accessing device register
on a different cpu.
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abdb8bc94b ]
Similar to mt7915_mcu_wtbl_generic_tlv, rely on vif->bss_conf.aid for
aid in sta mode and not on sta->aid.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a56b1b0f14 ]
mac80211 provides aid in vif->bss_conf.aid for sta mode and not in
sta->aid. Fix mt7915_mcu_wtbl_generic_tlv routine using proper value for
aid in sta mode.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74c337ec09 ]
Similar to mt7915 driver, fix tag len error for sta_rec_wtbl, which
causes fw parsing error for the tags placed behind it.
Fixes: d0e274af2f ("mt76: mt76_connac: create mcu library")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0198322379 ]
Trace IMC (In-Memory collection counters) in powerpc is useful for
application level profiling.
For trace_imc, presently task context (task_ctx_nr) is set to
perf_hw_context. But perf_hw_context should only be used for CPU PMU.
See commit 2665784850 ("perf/core: Verify we have a single
perf_hw_context PMU").
So for trace_imc, even though it is per thread PMU, it is preferred to
use sw_context in order to be able to do application level monitoring.
Hence change the task_ctx_nr to use perf_sw_context.
Fixes: 012ae24484 ("powerpc/perf: Trace imc PMU functions")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Update subject & incorporate notes into change log, reflow comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220202041837.65968-1-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ebb747492 ]
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
Fixes: e69eb0824d ("powerpc: dts: t1040rdb: add ports for Seville Ethernet switch")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220121091447.3412907-1-bigunclemax@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba18dad0fb ]
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f322a620be ]
For now, if the XDP prog returns XDP_PASS on XSK, the metadata
will be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match ixgbe_construct_skb().
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f405221a7 ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, ixgbe_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fbdaa1338 ]
To not dereference bi->xdp each time in ixgbe_construct_skb_zc(),
pass bi->xdp as an argument instead of bi. We can also call
xsk_buff_free() outside of the function as well as assign bi->xdp
to NULL, which seems to make it closer to its name.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9e61d365b ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dba29537c ]
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc97f9c6f9 ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 678dfd5280 ]
timestamping checks socket options during initialisation. For the field
bind_phc of the socket option SO_TIMESTAMPING it expects the value -1 if
PHC is not bound. Actually the value of bind_phc is 0 if PHC is not
bound. This results in the following output:
SIOCSHWTSTAMP: tx_type 0 requested, got 0; rx_filter 0 requested, got 0
SO_TIMESTAMP 0
SO_TIMESTAMPNS 0
SO_TIMESTAMPING flags 0, bind phc 0
not expected, flags 0, bind phc -1
This is fixed by setting default value and expected value of bind_phc to
0.
Fixes: 2214d70324 ("selftests/net: timestamping: support binding PHC")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1e0df1c57 ]
Syzbot reported 2 KMSAN bugs in ath9k. All of them are caused by missing
field initialization.
In htc_connect_service() svc_meta_len and pad are not initialized. Based
on code it looks like in current skb there is no service data, so simply
initialize svc_meta_len to 0.
htc_issue_send() does not initialize htc_frame_hdr::control array. Based
on firmware code, it will initialize it by itself, so simply zero whole
array to make KMSAN happy
Fail logs:
BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline]
hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479
htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline]
htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275
...
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258
...
Bytes 4-7 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline]
hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479
htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline]
htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275
...
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258
...
Bytes 16-17 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Reported-by: syzbot+f83a1df1ed4f67e8d8ad@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115122733.11160-1-paskripkin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec74489a8 ]
Use temp netns instead of hard code name for testing in case the netns
already exists.
Remove the hard code interface index when creating the veth interfaces.
Because when the system loads some virtual interface modules, e.g. tunnels.
the ifindex of 2 will be used and the cmd will fail.
As the netns has not created if checking environment failed. Trap the
clean up function after checking env.
Fixes: 8955c1a329 ("selftests/bpf/xdp_redirect_multi: Limit the tests in netns")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Link: https://lore.kernel.org/r/20220125081717.1260849-2-liuhangbin@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fffa0e345 ]
Convert almost all SEC("xdp_blah") uses to strict SEC("xdp") to comply
with strict libbpf 1.0 logic of exact section name match for XDP program
types. There is only one exception, which is only tested through
iproute2 and defines multiple XDP programs within the same BPF object.
Given iproute2 still works in non-strict libbpf mode and it doesn't have
means to specify XDP programs by its name (not section name/title),
leave that single file alone for now until iproute2 gains lookup by
function/program name.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/bpf/20210928161946.2512801-3-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f3a00c7f5 ]
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb4 ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430e6a0212 ]
clang static analysis reports this represenative problem
amdgpu_smu.c:144:18: warning: The left operand of '*' is a garbage value
return clk_freq * 100;
~~~~~~~~ ^
If there is no get_dpm_ultimate_freq function,
smu_get_dpm_freq_range returns success without setting the
output min,max parameters. So return an -ENOTSUPP error.
Fixes: e5ef784b1e ("drm/amd/powerplay: revise calling chain on retrieving frequency range")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 588a70177d ]
In amdgpu_dm_connector_add_common_modes(), amdgpu_dm_create_common_mode()
is assigned to mode and is passed to drm_mode_probed_add() directly after
that. drm_mode_probed_add() passes &mode->head to list_add_tail(), and
there is a dereference of it in list_add_tail() without recoveries, which
could lead to NULL pointer dereference on failure of
amdgpu_dm_create_common_mode().
Fix this by adding a NULL check of mode.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: e7b07ceef2 ("drm/amd/display: Merge amdgpu_dm_types and amdgpu_dm")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2343bcdb47 ]
In nvkm_acr_hsfw_load_bl(), the return value of kmalloc() is directly
passed to memcpy(), which could lead to undefined behavior on failure
of kmalloc().
Fix this bug by using kmemdup() instead of kmalloc()+memcpy().
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 22dcda45a3 ("drm/nouveau/acr: implement new subdev to replace "secure boot"")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124165856.57022-1-zhou1615@umn.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8fd0271da ]
It's possible the FW is already shutting down while the driver is being
removed and/or when the driver is going through reset. This can cause
unexpected/unnecessary errors to be printed:
eth0: DEV_CMD IONIC_CMD_PORT_RESET (12) error, IONIC_RC_ERROR (29) failed
eth1: DEV_CMD IONIC_CMD_RESET (3) error, IONIC_RC_ERROR (29) failed
Fix this by checking the FW status register before issuing the reset
commands.
Also, since err may not be assigned in ionic_port_reset(), assign it a
default value of 0, and remove an unnecessary log message.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad2939a15 ]
The watchdog expects the lif to fully exist when it goes off,
so lets not start the watchdog until all is ready in case there
is some quirky time dialation that makes probe take multiple
seconds.
Fixes: 089406bc5a ("ionic: add a watchdog timer to monitor heartbeat")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc0bf9de6f ]
Sparse seems to have gotten a little more picky lately and
we need to revisit this bit of code to make sparse happy.
warning: incorrect type in initializer (different address spaces)
expected union ionic_dev_cmd_regs *regs
got union ionic_dev_cmd_regs [noderef] __iomem *dev_cmd_regs
warning: incorrect type in argument 2 (different address spaces)
expected void [noderef] __iomem *
got unsigned int *
warning: incorrect type in argument 1 (different address spaces)
expected void volatile [noderef] __iomem *
got union ionic_dev_cmd *
Fixes: d701ec326a ("ionic: clean up sparse complaints")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4adc33f36d ]
The current code assumes that the RGB444 and YUV444 formats are the
same, but the HDMI 2.0 specification states that:
The three DC_XXbit bits above only indicate support for RGB 4:4:4 at
that pixel size. Support for YCBCR 4:4:4 in Deep Color modes is
indicated with the DC_Y444 bit. If DC_Y444 is set, then YCBCR 4:4:4
is supported for all modes indicated by the DC_XXbit flags.
So if we have YUV444 support and any DC_XXbit flag set but the DC_Y444
flag isn't, we'll assume that we support that deep colour mode for
YUV444 which breaks the specification.
In order to fix this, let's split the edid_hdmi_dc_modes field in struct
drm_display_info into two fields, one for RGB444 and one for YUV444.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-4-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75478b3b39 ]
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-3-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e68f331c8 ]
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
Fixes: 2c22120fbd ("MTD: OneNAND: interrupt based wait support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220104162658.1988142-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
