[ Upstream commit bd52cd5e23 ]
The argument of scatterwalk_unmap() is supposed to be the void* that was
returned by the previous scatterwalk_map() call.
The s390 AES-GCM implementation was instead passing the pointer to the
struct scatter_walk.
This doesn't actually break anything because scatterwalk_unmap() only uses
its argument under CONFIG_HIGHMEM and ARCH_HAS_FLUSH_ON_KUNMAP.
Fixes: bf7fa03870 ("s390/crypto: add s390 platform specific aes gcm support.")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20220517143047.3054498-1-jannh@google.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b232b02bf3 ]
In __device_attach function, The lock holding logic is as follows:
...
__device_attach
device_lock(dev) // get lock dev
async_schedule_dev(__device_attach_async_helper, dev); // func
async_schedule_node
async_schedule_node_domain(func)
entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC);
/* when fail or work limit, sync to execute func, but
__device_attach_async_helper will get lock dev as
well, which will lead to A-A deadlock. */
if (!entry || atomic_read(&entry_count) > MAX_WORK) {
func;
else
queue_work_node(node, system_unbound_wq, &entry->work)
device_unlock(dev)
As shown above, when it is allowed to do async probes, because of
out of memory or work limit, async work is not allowed, to do
sync execute instead. it will lead to A-A deadlock because of
__device_attach_async_helper getting lock dev.
To fix the deadlock, move the async_schedule_dev outside device_lock,
as we can see, in async_schedule_node_domain, the parameter of
queue_work_node is system_unbound_wq, so it can accept concurrent
operations. which will also not change the code logic, and will
not lead to deadlock.
Fixes: 765230b5f0 ("driver-core: add asynchronous probing support for drivers")
Signed-off-by: Zhang Wensheng <zhangwensheng5@huawei.com>
Link: https://lore.kernel.org/r/20220518074516.1225580-1-zhangwensheng5@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 660ba678f9 ]
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix this issue by calling kobject_put().
Fixes: 948af1f0bb ("firmware: Basic dmi-sysfs support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220511071421.9769-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1deeda8d28 ]
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d04394 (serial: stm32: fix word length configuration)
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c069d2756c ]
Only CS8 is supported but CSIZE was not sanitized to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Similarly, INPCK, PARMRK, and BRKINT are reported textually unsupported
but were not cleared in termios c_iflag which is the machine-readable
format.
Fixes: 45c054d081 (tty: serial: add driver for the SiFive UART)
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 098333a9c7 ]
Only CS7 and CS8 are supported but CSIZE is not sanitized after
fallthrough from CS5 or CS6 to CS7.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c10b13325c (tty: serial: Add RDA8810PL UART driver)
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af01792709 ]
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
Fixes: 7ecc77011c ("serial: 8250_fintek: Return -EINVAL on invalid configuration")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/035c738-8ea5-8b17-b1d7-84a7b3aeaa51@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589f892ac8 ]
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
CPU0 CPU1
meson_serial_console_write meson_uart_startup
-------------------------- ------------------
spin_lock(port->lock)
val = readl(AML_UART_CONTROL)
uart_console_write()
writel(INT_EN, AML_UART_CONTROL)
writel(val, AML_UART_CONTROL)
spin_unlock(port->lock)
Add port->lock synchronization to meson_uart_startup() to avoid
racing with meson_serial_console_write().
Also add detailed comments to meson_uart_reset() explaining why it
is *not* using port->lock synchronization.
Link: https://lore.kernel.org/lkml/2a82eae7-a256-f70c-fd82-4e510750906e@samsung.com
Fixes: ff7693d079 ("ARM: meson: serial: add MesonX SoC on-chip uart driver")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20220508103547.626355-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 782cd939cb ]
Add device managed action to sync pending queue work, otherwise
the queued work may run after the work is destroyed.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1adff542d6 ]
The panic notifier infrastructure executes registered callbacks when
a panic event happens - such callbacks are executed in atomic context,
with interrupts and preemption disabled in the running CPU and all other
CPUs disabled. That said, mutexes in such context are not a good idea.
This patch replaces a regular mutex with a mutex_trylock safer approach;
given the nature of the mutex used in the driver, it should be pretty
uncommon being unable to acquire such mutex in the panic path, hence
no functional change should be observed (and if it is, that would be
likely a deadlock with the regular mutex).
Fixes: 2227b7c746 ("coresight: add support for CPU debug module")
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20220427224924.592546-10-gpiccoli@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a7ff843d5 ]
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
References:
[1] "SiFive FU740-C000 Manual", v1p3, SiFive, Inc., August 13, 2021,
Section 16.9 "Baud Rate Divisor Register (div)", pp.143-144
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1f1496a923 ("riscv: Fix sifive serial driver")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656280.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a0793ac66 ]
The bug is here:
pmem->vaddr = NULL;
The list iterator 'pmem' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, just gen_pool_free/set NULL/list_del() and return
when found, otherwise list_del HEAD and return;
Fixes: 7ca5ce8965 ("firmware: add Intel Stratix10 service layer driver")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220414035609.2239-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ac11fe03a ]
The bug is here:
if (!buf) {
The list iterator value 'buf' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty (in this case, the
check 'if (!buf) {' will always be false and never exit expectly).
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'buf' as a dedicated pointer to
point to the found element.
Fixes: 2419e55e53 ("misc: fastrpc: add mmap/unmap support")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220327062202.5720-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e3b07ca5c ]
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d088fabace ]
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
Fixes: 2c8c981589 ("staging: usbip: let client choose device configuration")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220412165055.257113-1-dossche.niels@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f398e0aa32 ]
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65a8b28702 ]
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 3593030761 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Fixes: 3593030761 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Gibson <daniel@gibson.sh>
Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9800c81d ]
As the possible failure of the kmalloc(), the not_checked and checked
could be NULL pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, we need to kfree the 'not_checked' and 'checked' to avoid
the memory leak if fails.
And since it is just a test, it may directly return without error
number.
Fixes: ae2e1aad3e ("drivers/misc/lkdtm/bugs.c: add arithmetic overflow and array bounds checks")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220120092936.1874264-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3928cf0833 ]
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
ERROR: modpost: "bcsr_read" [drivers/pcmcia/db1xxx_ss.ko] undefined!
ERROR: modpost: "bcsr_mod" [drivers/pcmcia/db1xxx_ss.ko] undefined!
Fixes: 42a4f17dc3 ("MIPS: Alchemy: remove SOC_AU1X00 in favor of MIPS_ALCHEMY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
