[ Upstream commit 93b919da64 ]
symlink body shouldn't be freed without an RCU delay. Switch debugfs to
->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback. Similar to solution for bpf, only here it's even
more obvious that ->evict_inode() can be dropped.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fdcfab5b5 ]
free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ac0c24fe1 ]
Packets without the last descriptor set should be dropped early. If we
receive a frame larger than the DMA buffer, the HW will continue using the
next descriptor. Driver mistakes these as individual frames, and sometimes
a truncated frame (without the LD set) may look like a valid packet.
This fixes a strange issue where the system replies to 4098-byte ping
although the MTU/DMA buffer size is set to 4096, and yet at the same
time it's logging an oversized packet.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b746ce8b3 ]
If we have error bits set, the discard_frame status will get overwritten
by checksum bit checks, which might set the status back to good one.
Fix by checking the COE status only if the frame is good.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07b3975352 ]
Currently, if we drop a packet, we exit from NAPI loop before the budget
is consumed. In some situations this will make the RX processing stall
e.g. when flood pinging the system with oversized packets, as the
errorneous packets are not dropped efficiently.
If we drop a packet, we should just continue to the next one as long as
the budget allows.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 583e636141 ]
We always program the maximum DMA buffer size into the receive descriptor,
although the allocated size may be less. E.g. with the default MTU size
we allocate only 1536 bytes. If somebody sends us a bigger frame, then
memory may get corrupted.
Fix by using exact buffer sizes.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18bebc6dd3 ]
Bond expects ethernet hwaddr for its slave, but it can be longer than 6
bytes - infiniband interface for example.
# cat /sys/devices/<skipped>/net/ib0/address
80:00:02:08:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:be:5d:e1
# cat /sys/devices/<skipped>/net/ib0/bonding_slave/perm_hwaddr
80:00:02:08:fe:80
So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca4a92858 ]
Traditionally, the PF (Physical Function) which resides on vport 0 was
the E-switch manager. Since the ECPF (Embedded CPU Physical Function),
which resides on vport 0xfffe, was introduced as the E-Switch manager,
the assumption that the E-switch manager is on vport 0 is incorrect.
Since the eswitch code already uses the actual vport value, all we
need is to always set other_vport=1.
Signed-off-by: Omri Kahalon <omrik@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 669efc76b3 ]
Currently, the rules for configuring search paths in Kbuild have
changed, this will lead some erros when compiling hns3 with the
following command:
make O=DIR M=drivers/net/ethernet/hisilicon/hns3
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10:
fatal error: hnae3.h: No such file or directory
This patch fix it by adding $(srctree)/ prefix to the serach paths.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bafa1e962 ]
Similar to commit edfc3722cf ("HID: quirks: Fix keyboard + touchpad on
Toshiba Click Mini not working"), the Lenovo Miix 630 has a combo
keyboard/touchpad device with vid:pid of 04F3:0400, which is shared with
Elan touchpads. The combo on the Miix 630 has an ACPI id of QTEC0001,
which is not claimed by the elan_i2c driver, so key on that similar to
what was done for the Toshiba Click Mini.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbee9c9c45 ]
A memory save operation to 8-byte variable in RV32 is divided into
two sw instructions in the put_user macro. The current fixup returns
execution flow to the second sw instead of the one after it.
This patch fixes this fixup code according to the load access part.
Signed-off-by: Alan Kao<alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dabb8338be ]
The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.
Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.
Also move a couple of defines into the appropriate header file instead
of inline in the .c file.
Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <niveditas98@gmail.com>
Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d040e4e8de ]
The device tree compiler yells like this:
Warning (unit_address_vs_reg):
/gpu-opp-table/opp@100000000:
node has a unit name, but no reg property
Let's match the cpu opp node names and use a dash.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca8c3b922e ]
When CONFIG_CFG80211 isn't enabled the compiler correcly warns about
'sinfo.pertid' may be unused. It can also happen for other error
conditions that it not warn about.
net/batman-adv/bat_v_elp.c: In function ‘batadv_v_elp_get_throughput.isra.0’:
include/net/cfg80211.h:6370:13: warning: ‘sinfo.pertid’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
kfree(sinfo->pertid);
~~~~~^~~~~~~~
Rework so that we only release '&sinfo' if cfg80211_get_station returns
zero.
Fixes: 7d652669b6 ("batman-adv: release station info tidstats")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f131a56880 ]
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_global_free is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 7683fdc1e8 ("batman-adv: protect the local and the global trans-tables with rcu")
Reported-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d65b9acca ]
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_local_remove is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: ef72706a05 ("batman-adv: protect tt_local_entry from concurrent delete events")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ba104f468 ]
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_bla_del_claim is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d82d2249 ]
When no alarm has been programmed on RSK-RZA1, an error message is
printed during boot:
rtc rtc0: invalid alarm value: 2019-03-14T255:255:255
sh_rtc_read_alarm_value() returns 0xff when querying a hardware alarm
field that is not enabled. __rtc_read_alarm() validates the received
alarm values, and fills in missing fields when needed.
While 0xff is handled fine for the year, month, and day fields, and
corrected as considered being out-of-range, this is not the case for the
hour, minute, and second fields, where -1 is expected for missing
fields.
Fix this by returning -1 instead, as this value is handled fine for all
fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6752e185c ]
If we encounter a failure during suspend where this RTC was programmed
to wakeup the system from suspend, but that wakeup couldn't be
configured because the system didn't support wakeup interrupts, we'll
run into the following warning:
Unbalanced IRQ 166 wake disable
WARNING: CPU: 7 PID: 3071 at kernel/irq/manage.c:669 irq_set_irq_wake+0x108/0x278
This happens because the suspend process isn't aborted when the RTC
fails to configure the wakeup IRQ. Instead, we continue suspending the
system and then another suspend callback fails the suspend process and
"unwinds" the previously suspended drivers by calling their resume
callbacks. When we get back to resuming this RTC driver, we'll call
disable_irq_wake() on an IRQ that hasn't been configured for wake.
Let's just fail suspend/resume here if we can't configure the system to
wake and the user has chosen to wakeup with this device. This fixes this
warning and makes the code more robust in case there are systems out
there that can't wakeup from suspend on this line but the user has
chosen to do so.
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Evan Green <evgreen@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Cc: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-By: Benson Leung <bleung@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cef0d4948c ]
There is a race condition that could happen if hid_debug_rdesc_show()
is running while hdev is in the process of going away (device removal,
system suspend, etc) which could result in NULL pointer dereference:
BUG: unable to handle kernel paging request at 0000000783316040
CPU: 1 PID: 1512 Comm: getevent Tainted: G U O 4.19.20-quilt-2e5dc0ac-00029-gc455a447dd55 #1
RIP: 0010:hid_dump_device+0x9b/0x160
Call Trace:
hid_debug_rdesc_show+0x72/0x1d0
seq_read+0xe0/0x410
full_proxy_read+0x5f/0x90
__vfs_read+0x3a/0x170
vfs_read+0xa0/0x150
ksys_read+0x58/0xc0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x55/0x110
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Grab driver_input_lock to make sure the input device exists throughout the
whole process of dumping the rdesc.
[jkosina@suse.cz: update changelog a bit]
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: "Zhang, Jun" <jun.zhang@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c44b15e1c ]
create_singlethread_workqueue may fail and return NULL. The fix checks if it is
NULL to avoid NULL pointer dereference. Also, the fix moves the call of
create_singlethread_workqueue earlier to avoid resource-release issues.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 924726888f ]
The rk3328-roc-cc board exhibits tx stability issues with large packets,
as does the rock64 board, which was fixed with this patch
https://patchwork.kernel.org/patch/10178969/
A similar patch was merged for the rk3328-roc-cc here
https://patchwork.kernel.org/patch/10804863/
but it doesn't include the tx/rx_delay tweaks, and I find that they
help with an issue where large transfers would bring the ethernet
link down, causing a link reset regularly.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c2b71462d2 upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c01c348ecd upstream.
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c409ca3be3 upstream.
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c
Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) * usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.
Fixes: c6688ef9f2 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip <malte@leip.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc834e607a upstream.
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB. This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.
In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS. Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop. The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.
This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner. It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed. And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).
Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c114944d7d upstream.
The syzkaller USB fuzzer spotted a slab-out-of-bounds bug in the
ds2490 driver. This bug is caused by improper use of the altsetting
array in the usb_interface structure (the array's entries are not
always stored in numerical order), combined with a naive assumption
that all interfaces probed by the driver will have the expected number
of altsettings.
The bug can be fixed by replacing references to the possibly
non-existent intf->altsetting[alt] entry with the guaranteed-to-exist
intf->cur_altsetting entry.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d65f673b847a1a96cdba@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef61eb43ad upstream.
The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver. The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.
This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone. The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a29c57b76 upstream.
Add two Dell platform for headset mode.
[ Note: this is a further correction / addition of the previous
pin-based quirks for Dell machines; another entry for ALC236 with
the d-mic pin 0x12 and an entry for ALC295 -- tiwai ]
Fixes: b26e36b7ef ("ALSA: hda/realtek - add two more pin configuration sets to quirk table")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72bfcee11c upstream.
Multiple users have reported their Synaptics touchpad has stopped
working between v4.20.1 and v4.20.2 when using SMBus interface.
The culprit for this appeared to be commit c5eb119007 ("PCI / PM: Allow
runtime PM without callback functions") that fixed the runtime PM for
i2c-i801 SMBus adapter. Those Synaptics touchpad are using i2c-i801
for SMBus communication and testing showed they are able to get back
working by preventing the runtime suspend of adapter.
Normally when i2c-i801 SMBus adapter transmits with the client it resumes
before operation and autosuspends after.
However, if client requires SMBus Host Notify protocol, what those
Synaptics touchpads do, then the host adapter must not go to runtime
suspend since then it cannot process incoming SMBus Host Notify commands
the client may send.
Fix this by keeping I2C/SMBus adapter active in case client requires
Host Notify.
Reported-by: Keijo Vaara <ferdasyn@rocketmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203297
Fixes: c5eb119007 ("PCI / PM: Allow runtime PM without callback functions")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Keijo Vaara <ferdasyn@rocketmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b6604c5a upstream.
A previous change allowed I2C client devices to discover new IRQs upon
reprobe by clearing the IRQ in i2c_device_remove. However, if an IRQ was
assigned in i2c_new_device, that information is lost.
For example, the touchscreen and trackpad devices on a Dell Inspiron laptop
are I2C devices whose IRQs are defined by ACPI extended IRQ types. The
client device structures are initialized during an ACPI walk. After
removing the i2c_hid device, modprobe fails.
This change caches the initial IRQ value in i2c_new_device and then resets
the client device IRQ to the initial value in i2c_device_remove.
Fixes: 6f108dd70d ("i2c: Clear client->irq in i2c_device_remove")
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
[wsa: this is an easy to backport fix for the regression. We will
refactor the code to handle irq assignments better in general.]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f108dd70d upstream.
The IRQ will be mapped in i2c_device_probe only if client->irq is zero and
i2c_device_remove does not clear this. When rebinding an I2C device,
whos IRQ provider has also been rebound this means that an IRQ mapping
will never be created, causing the I2C device to fail to acquire its
IRQ. Fix this issue by clearing client->irq in i2c_device_remove,
forcing i2c_device_probe to lookup the mapping again.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e0cf3cae upstream.
The I2C host driver for SynQuacer fails to populate the of_node and
ACPI companion fields of the struct i2c_adapter it instantiates,
resulting in enumeration of the subordinate I2C bus to fail.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5178791474 upstream.
We need to dereference the directory to get its parent to
be able to rename it, so it's clearly not safe to try to
do this with ERR_PTR() pointers. Skip in this case.
It seems that this is most likely what was causing the
report by syzbot, but I'm not entirely sure as it didn't
come with a reproducer this time.
Cc: stable@vger.kernel.org
Reported-by: syzbot+4ece1a28b8f4730547c9@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b82d6c1f8f upstream.
The commit fc3a2fcaa1 ("mwifiex: use atomic bitops to represent
adapter status variables") had a fairly straightforward bug in it. It
contained this bit of diff:
- if (!adapter->is_suspended) {
+ if (test_bit(MWIFIEX_IS_SUSPENDED, &adapter->work_flags)) {
As you can see the patch missed the "!" when converting to the atomic
bitops. This meant that the resume hasn't done anything at all since
that commit landed and suspend/resume for mwifiex SDIO cards has been
totally broken.
After fixing this mwifiex suspend/resume appears to work again, at
least with the simple testing I've done.
Fixes: fc3a2fcaa1 ("mwifiex: use atomic bitops to represent adapter status variables")
Cc: <stable@vger.kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c9adef978 upstream.
We introduced a bug that prevented this old device from
working. The driver would simply not be able to complete
the INIT flow while spewing this warning:
CSR addresses aren't configured
WARNING: CPU: 0 PID: 819 at drivers/net/wireless/intel/iwlwifi/pcie/drv.c:917
iwl_pci_probe+0x160/0x1e0 [iwlwifi]
Cc: stable@vger.kernel.org # v4.18+
Fixes: a8cbb46f83 ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: c8f1b51e50 ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e80ad37f6 upstream.
ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.
Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Fixes: f279294e9e ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5c812e84f upstream.
The line6 driver uses a lot of USB buffers off of the stack, which is
not allowed on many systems, causing the driver to crash on some of
them. Fix this up by dynamically allocating the buffers with kmalloc()
which allows for proper DMA-able memory.
Reported-by: Christo Gouws <gouws.christo@gmail.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Christo Gouws <gouws.christo@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8764ed55c9 upstream.
KVM's recent bug fix to update %rip after emulating I/O broke userspace
that relied on the previous behavior of incrementing %rip prior to
exiting to userspace. When running a Windows XP guest on AMD hardware,
Qemu may patch "OUT 0x7E" instructions in reaction to the OUT itself.
Because KVM's old behavior was to increment %rip before exiting to
userspace to handle the I/O, Qemu manually adjusted %rip to account for
the OUT instruction.
Arguably this is a userspace bug as KVM requires userspace to re-enter
the kernel to complete instruction emulation before taking any other
actions. That being said, this is a bit of a grey area and breaking
userspace that has worked for many years is bad.
Pre-increment %rip on OUT to port 0x7e before exiting to userspace to
hack around the issue.
Fixes: 45def77ebf ("KVM: x86: update %rip after emulating IO")
Reported-by: Simon Becherer <simon@becherer.de>
Reported-and-tested-by: Iakov Karpov <srid@rkmail.ru>
Reported-by: Gabriele Balducci <balducci@units.it>
Reported-by: Antti Antinoja <reader@fennosys.fi>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
