commit 9bf3d20331 upstream.
The block number in the quota tree on disk should be smaller than the
v2_disk_dqinfo.dqi_blocks. If the quota file was corrupted, we may be
allocating an 'allocated' block and that would lead to a loop in a tree,
which will probably trigger oops later. This patch adds a check for the
block number in the quota tree to prevent such potential issue.
Link: https://lore.kernel.org/r/20211008093821.1001186-2-yi.zhang@huawei.com
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Cc: stable@kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 661c399a65 upstream.
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ca6d7fa3 upstream.
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a41ae80bd upstream.
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40fdea0284 upstream.
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 027b57170b upstream.
Since commit edc6afc549 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc549 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dfbc624eb upstream.
Check the current VMCS controls to determine if an MSR write will be
intercepted due to MSR bitmaps being disabled. In the nested VMX case,
KVM will disable MSR bitmaps in vmcs02 if they're disabled in vmcs12 or
if KVM can't map L1's bitmaps for whatever reason.
Note, the bad behavior is relatively benign in the current code base as
KVM sets all bits in vmcs02's MSR bitmap by default, clears bits if and
only if L0 KVM also disables interception of an MSR, and only uses the
buggy helper for MSR_IA32_SPEC_CTRL. Because KVM explicitly tests WRMSR
before disabling interception of MSR_IA32_SPEC_CTRL, the flawed check
will only result in KVM reading MSR_IA32_SPEC_CTRL from hardware when it
isn't strictly necessary.
Tag the fix for stable in case a future fix wants to use
msr_write_intercepted(), in which case a buggy implementation in older
kernels could prove subtly problematic.
Fixes: d28b387fb7 ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223a3b8283 upstream.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b1 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95bf9d646c upstream.
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Maciej Rozycki <macro@orcam.me.uk>
Cc: linux-mips@vger.kernel.org
[1] 35938a00ba ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Cc: stable@vger.kernel.org
Fixes: f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d613f9f72 upstream.
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
Cc: stable@vger.kernel.org
Fixes: 3d749b9e67 ("ptrace: simplify ptrace_stop()->sigkill_pending() path")
Fixes: 1a669c2f16 ("Add arch_ptrace_stop")
Link: https://lkml.kernel.org/r/87pmsyx29t.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b515d09705 upstream.
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ac601882 upstream.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b14ed6e11 upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c76 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f971a85439 upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4eb8223 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a006acb931 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1b9ca365d upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee35868 ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f8765a11 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c78a5e7aa upstream.
In open_ctree() in btrfs_check_rw_degradable() [1], we check each block
group individually if at least the minimum number of devices is available
for that profile. If all the devices are available, then we don't have to
check degradable.
[1]
open_ctree()
::
3559 if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
Also before calling btrfs_check_rw_degradable() in open_ctee() at the
line number shown below [2] we call btrfs_read_chunk_tree() and down to
add_missing_dev() to record number of missing devices.
[2]
open_ctree()
::
3454 ret = btrfs_read_chunk_tree(fs_info);
btrfs_read_chunk_tree()
read_one_chunk() / read_one_dev()
add_missing_dev()
So, check if there is any missing device before btrfs_check_rw_degradable()
in open_ctree().
Also, with this the mount command could save ~16ms.[3] in the most
common case, that is no device is missing.
[3]
1) * 16934.96 us | btrfs_check_rw_degradable [btrfs]();
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10adb1152d upstream.
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d03dbebba upstream.
Reported bug: https://github.com/kdave/btrfs-progs/issues/389
There's a problem with scrub reporting aborted status but returning
error code 0, on a filesystem with missing and readded device.
Roughly these steps:
- mkfs -d raid1 dev1 dev2
- fill with data
- unmount
- make dev1 disappear
- mount -o degraded
- copy more data
- make dev1 appear again
Running scrub afterwards reports that the command was aborted, but the
system log message says the exit code was 0.
It seems that the cause of the error is decrementing
fs_devices->missing_devices but not clearing device->dev_state. Every
time we umount filesystem, it would call close_ctree, And it would
eventually involve btrfs_close_one_device to close the device, but it
only decrements fs_devices->missing_devices but does not clear the
device BTRFS_DEV_STATE_MISSING bit. Worse, this bug will cause Integer
Overflow, because every time umount, fs_devices->missing_devices will
decrease. If fs_devices->missing_devices value hit 0, it would overflow.
With added debugging:
loop1: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 1 transid 21 /dev/loop1 scanned by systemd-udevd (2311)
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 2 transid 17 /dev/loop2 scanned by systemd-udevd (2313)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 0
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 18446744073709551615
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 18446744073709551615
If fs_devices->missing_devices is 0, next time it would be 18446744073709551615
After apply this patch, the fs_devices->missing_devices seems to be
right:
$ truncate -s 10g test1
$ truncate -s 10g test2
$ losetup /dev/loop1 test1
$ losetup /dev/loop2 test2
$ mkfs.btrfs -draid1 -mraid1 /dev/loop1 /dev/loop2 -f
$ losetup -d /dev/loop2
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ dmesg
loop1: detected capacity change from 0 to 20971520
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 1 transid 5 /dev/loop1 scanned by mkfs.btrfs (1863)
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 2 transid 5 /dev/loop2 scanned by mkfs.btrfs (1863)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): checking UUID tree
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Li Zhang <zhanglikernel@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90a881fc35 ]
MTU change is refused whenever the value of new MTU is bigger than
the max packet bytes that fits in NFP Cluster Target Memory (CTM).
However, an eBPF program doesn't always need to access the whole
packet data.
The maximum direct packet access (DPA) offset has always been
caculated by verifier and stored in the max_pkt_offset field of prog
aux data.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9159f10240 ]
The netif_device_detach() conditionally stops all tx queues if the queues
are running. There is no need to call netif_tx_stop_all_queues() again.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
