[ Upstream commit f7b7d30158cff246667273bd2a62fc93ee0725d2 ]
If the parent clock rate is greater than unsigned long max/2 then
integer overflow happens when calculating the clock rate on 32-bit systems.
As RCG2 uses half integer dividers, the clock rate is first being
multiplied by 2 which will overflow the unsigned long max value.
Hence, replace the common pattern of doing 64-bit multiplication
and then a do_div() call with simpler mult_frac call.
Fixes: bcd61c0f53 ("clk: qcom: Add support for root clock generators (RCGs)")
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230901073640.4973-1-quic_devipriy@quicinc.com
[bjorn: Also drop unnecessary {} around single statements]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb9913b511f10968a02cfa5329a896855dd152a3 ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Fix this by stop calling request_irq() with invalid IRQ #s.
Fixes: dc4dc36056 ("spi: tegra: add spi driver for SLINK controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/tencent_73FCC06A3D1C14EE5175253C6FB46A07B709@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff672b9ffeb3f82135488ac16c5c5eb4b992999b ]
Both ipvlan_process_v4_outbound() and ipvlan_process_v6_outbound()
increment dev->stats.tx_errors in case of errors.
Unfortunately there are two issues :
1) ipvlan_get_stats64() does not propagate dev->stats.tx_errors to user.
2) Increments are not atomic. KCSAN would complain eventually.
Use DEV_STATS_INC() to not miss an update, and change ipvlan_get_stats64()
to copy the value back to user.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Link: https://lore.kernel.org/r/20231026131446.3933175-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b068c714ca9479d2783cc333fff5bc2d4a6d45c ]
Companion of DEV_STATS_INC() & DEV_STATS_ADD().
This is going to be used in the series.
Use it in macsec_get_stats64().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ff672b9ffeb3 ("ipvlan: properly track tx_errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03d6c848bfb406e9ef6d9846d759e97beaeea113 ]
When the ipv6 stack output a GSO packet, if its gso_size is larger than
dst MTU, then all segments would be fragmented. However, it is possible
for a GSO packet to have a trailing segment with smaller actual size
than both gso_size as well as the MTU, which leads to an "atomic
fragment". Atomic fragments are considered harmful in RFC-8021. An
Existing report from APNIC also shows that atomic fragments are more
likely to be dropped even it is equivalent to a no-op [1].
Add an extra check in the GSO slow output path. For each segment from
the original over-sized packet, if it fits with the path MTU, then avoid
generating an atomic fragment.
Link: https://www.potaroo.net/presentations/2022-03-01-ipv6-frag.pdf [1]
Fixes: b210de4f8c ("net: ipv6: Validate GSO SKB before finish IPv6 processing")
Reported-by: David Wragg <dwragg@cloudflare.com>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Link: https://lore.kernel.org/r/90912e3503a242dca0bc36958b11ed03a2696e5e.1698156966.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48cf49d31994ff97b33c4044e618560ec84d35fb ]
snprintf() does not return negative values on error.
To know if the buffer was too small, the returned value needs to be
compared with the length of the passed buffer. If it is greater or
equal, the output has been truncated, so add checks for the truncation
to create_pnp_modalias() and create_of_modalias(). Also make them
return -ENOMEM in that case, as they already do that elsewhere.
Moreover, the remaining size of the buffer used by snprintf() needs to
be updated after the first write to avoid out-of-bounds access as
already done correctly in create_pnp_modalias(), but not in
create_of_modalias(), so change the latter accordingly.
Fixes: 8765c5ba19 ("ACPI / scan: Rework modalias creation when "compatible" is present")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ rjw: Merge two patches into one, combine changelogs, add subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d35381aa73f7e1e8b25f3ed5283287a64d9ddff5 ]
htab_lock_bucket uses the following logic to avoid recursion:
1. preempt_disable();
2. check percpu counter htab->map_locked[hash] for recursion;
2.1. if map_lock[hash] is already taken, return -BUSY;
3. raw_spin_lock_irqsave();
However, if an IRQ hits between 2 and 3, BPF programs attached to the IRQ
logic will not able to access the same hash of the hashtab and get -EBUSY.
This -EBUSY is not really necessary. Fix it by disabling IRQ before
checking map_locked:
1. preempt_disable();
2. local_irq_save();
3. check percpu counter htab->map_locked[hash] for recursion;
3.1. if map_lock[hash] is already taken, return -BUSY;
4. raw_spin_lock().
Similarly, use raw_spin_unlock() and local_irq_restore() in
htab_unlock_bucket().
Fixes: 20b6cc34ea ("bpf: Avoid hashtab deadlock with map_locked")
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/7a9576222aa40b1c84ad3a9ba3e64011d1a04d41.camel@linux.ibm.com
Link: https://lore.kernel.org/bpf/20231012055741.3375999-1-song@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 181a42edddf51d5d9697ecdf365d72ebeab5afb0 ]
The handle of new hci_conn is always HCI_CONN_HANDLE_MAX + 1 if
the handle of the first hci_conn entry in hci_dev->conn_hash->list
is not HCI_CONN_HANDLE_MAX + 1. Use ida to manage the allocation of
hci_conn->handle to make it be unique.
Fixes: 9f78191cc9 ("Bluetooth: hci_conn: Always allocate unique handles")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d11d70d1f6b23e7d3fc00396c17b90b876162a4 ]
This enables a broadcast sink to be informed if the PA
it has synced with is associated with an encrypted BIG,
by retrieving the socket QoS and checking the encryption
field.
After PA sync has been successfully established and the
first BIGInfo advertising report is received, a new hcon
is added and notified to the ISO layer. The ISO layer
sets the encryption field of the socket and hcon QoS
according to the encryption parameter of the BIGInfo
advertising report event.
After that, the userspace is woken up, and the QoS of the
new PA sync socket can be read, to inspect the encryption
field and follow up accordingly.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 181a42edddf5 ("Bluetooth: Make handle of hci_conn be unique")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 658939fc68d3241f9a0019e224cd7154438c23f2 ]
If a TX queue has no space for new TX frames, the driver will keep
these frames in the overflow queue, and during reclaim flow it
will retry to send the frames from that queue.
But if the reclaim flow was invoked from TX queue flush, we will also
TX these frames, which is wrong as we don't want to TX anything
after flush.
This might also cause assert 0x125F when removing the queue,
saying that the driver removes a non-empty queue
Fix this by TXing the overflow queue's frames only if we are
not in flush queue flow.
Fixes: a445098058 ("iwlwifi: move reclaim flows to the queue file")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.caf06c8709d9.Ibf664ccb3f952e836f8fa461ea58fc08e5c46e88@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43874283ce6c5bd32ac9d30878b2c96a974357cb ]
When I implemented iwl_mvm_mac_flush_sta() I completely botched it;
it basically always happens after the iwl_mvm_sta_pre_rcu_remove()
call, and that already clears mvm->fw_id_to_mac_id[] entries, so we
cannot rely on those at iwl_mvm_mac_flush_sta() time. This means it
never did anything.
Fix this by just going through the station IDs and now with the new
API for iwl_mvm_flush_sta(), call those.
Fixes: a6cc6ccb1c ("wifi: iwlwifi: mvm: support new flush_sta method")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.0b5878e93118.I1093e60163052e7be64d2b01424097cd6a272979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a86dcb4a908845e6b7ff39b78fb1141b895408f ]
The management frames protection flag is always set when the station
is not yet authorized. However, it was not cleared after association
even if the association did not use MFP. As a result, all public
action frames are not parsed by fw (which will cause FTM to fail,
for example). Update the station MFP flag after the station is
authorized.
Fixes: 4c8d5c8d07 ("wifi: iwlwifi: mvm: tell firmware about per-STA MFP enablement")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926110319.2488cbd01bde.Ic0f08b7d3efcbdce27ec897f84d740fec8d169ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73ed8e03388d16c12fc577e5c700b58a29045a15 ]
cookie_init_timestamp() is supposed to return a 64bit timestamp
suitable for both TSval determination and setting of skb->tstamp.
Unfortunately it uses 32bit fields and overflows after
2^32 * 10^6 nsec (~49 days) of uptime.
Generated TSval are still correct, but skb->tstamp might be set
far away in the past, potentially confusing other layers.
tcp_ns_to_ts() is changed to return a full 64bit value,
ts and ts_now variables are changed to u64 type,
and TSMASK is removed in favor of shifts operations.
While we are at it, change this sequence:
ts >>= TSBITS;
ts--;
ts <<= TSBITS;
ts |= options;
to:
ts -= (1UL << TSBITS);
Fixes: 9a568de481 ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d9ddbacb102621af6d28ff7bf5a0b4ce249d8 ]
tp->rcv_tstamp should be set to tcp_jiffies, not tcp_time_stamp().
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf3986f8c01d355490d0ac6024391b989a9d1e9d ]
When searching for the trip points that need to be set, the nearest
higher trip point's temperature is used for the high trip, while the
nearest lower trip point's temperature minus the hysteresis is used for
the low trip. The issue with this logic is that when the current
temperature is inside a trip point's hysteresis range, both high and low
trips will come from the same trip point. As a consequence instability
can still occur like this:
* the temperature rises slightly and enters the hysteresis range of a
trip point
* polling happens and updates the trip points to the hysteresis range
* the temperature falls slightly, exiting the hysteresis range, crossing
the trip point and triggering an IRQ, the trip points are updated
* repeat
So even though the current hysteresis implementation prevents
instability from happening due to IRQs triggering on the same
temperature value, both ways, it doesn't prevent it from happening due
to an IRQ on one way and polling on the other.
To properly implement a hysteresis behavior, when inside the hysteresis
range, don't update the trip points. This way, the previously set trip
points will stay in effect, which will in a way remember the previous
state (if the temperature signal came from above or below the range) and
therefore have the right trip point already set.
The exception is if there was no previous trip point set, in which case
a previous state doesn't exist, and so it's sensible to allow the
hysteresis range as trip points.
The following logs show the current behavior when running on a real
machine:
[ 202.524658] thermal thermal_zone0: new temperature boundaries: -2147483647 < x < 40000
203.562817: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=36986 temp=37979
[ 203.562845] thermal thermal_zone0: new temperature boundaries: 37000 < x < 40000
204.176059: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=37979 temp=40028
[ 204.176089] thermal thermal_zone0: new temperature boundaries: 37000 < x < 100000
205.226813: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=40028 temp=38652
[ 205.226842] thermal thermal_zone0: new temperature boundaries: 37000 < x < 40000
And with this patch applied:
[ 184.933415] thermal thermal_zone0: new temperature boundaries: -2147483647 < x < 40000
185.981182: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=36986 temp=37872
186.744685: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=37872 temp=40058
[ 186.744716] thermal thermal_zone0: new temperature boundaries: 37000 < x < 100000
187.773284: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=40058 temp=38698
Fixes: 060c034a97 ("thermal: Add support for hardware-tracked trip points")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Co-developed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da1055b673f3baac2249571c9882ce767a0aa746 ]
The linked list failure test 'pop_front_off' and 'pop_back_off'
currently rely on matching exact instruction and register values. The
purpose of the test is to ensure the offset is correctly incremented for
the returned pointers from list pop helpers, which can then be used with
container_of to obtain the real object. Hence, somehow obtaining the
information that the offset is 48 will work for us. Make the test more
robust by relying on verifier error string of bpf_spin_lock and remove
dependence on fragile instruction index or register number, which can be
affected by different clang versions used to build the selftests.
Fixes: 300f19dcdb ("selftests/bpf: Add BPF linked list API tests")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231020144839.2734006-1-memxor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4eee56e14fe001e1cff54f0b438a5e2d0dd7454 ]
Assume that caller's 'to' offset really represents an upper boundary for
the pattern search, so patterns extending past this offset are to be
rejected.
The old behaviour also was kind of inconsistent when it comes to
fragmentation (or otherwise non-linear skbs): If the pattern started in
between 'to' and 'from' offsets but extended to the next fragment, it
was not found if 'to' offset was still within the current fragment.
Test the new behaviour in a kselftest using iptables' string match.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: f72b948dcb ("[NET]: skb_find_text ignores to argument")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29a7e00ffadddd8d68eff311de1bf12ae10687bb ]
When employed within a sleepable program not under RCU protection, the
use of 'bpf_task_under_cgroup()' may trigger a warning in the kernel log,
particularly when CONFIG_PROVE_RCU is enabled:
[ 1259.662357] WARNING: suspicious RCU usage
[ 1259.662358] 6.5.0+ #33 Not tainted
[ 1259.662360] -----------------------------
[ 1259.662361] include/linux/cgroup.h:423 suspicious rcu_dereference_check() usage!
Other info that might help to debug this:
[ 1259.662366] rcu_scheduler_active = 2, debug_locks = 1
[ 1259.662368] 1 lock held by trace/72954:
[ 1259.662369] #0: ffffffffb5e3eda0 (rcu_read_lock_trace){....}-{0:0}, at: __bpf_prog_enter_sleepable+0x0/0xb0
Stack backtrace:
[ 1259.662385] CPU: 50 PID: 72954 Comm: trace Kdump: loaded Not tainted 6.5.0+ #33
[ 1259.662391] Call Trace:
[ 1259.662393] <TASK>
[ 1259.662395] dump_stack_lvl+0x6e/0x90
[ 1259.662401] dump_stack+0x10/0x20
[ 1259.662404] lockdep_rcu_suspicious+0x163/0x1b0
[ 1259.662412] task_css_set.part.0+0x23/0x30
[ 1259.662417] bpf_task_under_cgroup+0xe7/0xf0
[ 1259.662422] bpf_prog_7fffba481a3bcf88_lsm_run+0x5c/0x93
[ 1259.662431] bpf_trampoline_6442505574+0x60/0x1000
[ 1259.662439] bpf_lsm_bpf+0x5/0x20
[ 1259.662443] ? security_bpf+0x32/0x50
[ 1259.662452] __sys_bpf+0xe6/0xdd0
[ 1259.662463] __x64_sys_bpf+0x1a/0x30
[ 1259.662467] do_syscall_64+0x38/0x90
[ 1259.662472] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 1259.662479] RIP: 0033:0x7f487baf8e29
[...]
[ 1259.662504] </TASK>
This issue can be reproduced by executing a straightforward program, as
demonstrated below:
SEC("lsm.s/bpf")
int BPF_PROG(lsm_run, int cmd, union bpf_attr *attr, unsigned int size)
{
struct cgroup *cgrp = NULL;
struct task_struct *task;
int ret = 0;
if (cmd != BPF_LINK_CREATE)
return 0;
// The cgroup2 should be mounted first
cgrp = bpf_cgroup_from_id(1);
if (!cgrp)
goto out;
task = bpf_get_current_task_btf();
if (bpf_task_under_cgroup(task, cgrp))
ret = -1;
bpf_cgroup_release(cgrp);
out:
return ret;
}
After running the program, if you subsequently execute another BPF program,
you will encounter the warning.
It's worth noting that task_under_cgroup_hierarchy() is also utilized by
bpf_current_task_under_cgroup(). However, bpf_current_task_under_cgroup()
doesn't exhibit this issue because it cannot be used in sleepable BPF
programs.
Fixes: b5ad4cdc46 ("bpf: Add bpf_task_under_cgroup() kfunc")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Cc: Feng Zhou <zhoufeng.zf@bytedance.com>
Cc: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20231007135945.4306-1-laoar.shao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621735f590643e3048ca2060c285b80551660601 ]
In very rare cases (I've seen two reports so far about different
RTL8125 chip versions) it seems the MAC locks up when link goes down
and requires a software reset to get revived.
Realtek doesn't publish hw errata information, therefore the root cause
is unknown. Realtek vendor drivers do a full hw re-initialization on
each link-up event, the slimmed-down variant here was reported to fix
the issue for the reporting user.
It's not fully clear which parts of the NIC are reset as part of the
software reset, therefore I can't rule out side effects.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Reported-by: Martin Kjær Jørgensen <me@lagy.org>
Link: https://lore.kernel.org/netdev/97ec2232-3257-316c-c3e7-a08192ce16a6@gmail.com/T/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/9edde757-9c3b-4730-be3b-0ef3a374ff71@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c99626092efca3061b387043d4a7399bf75fbdd5 ]
The dev->id value comes from ida_alloc() so it's a number between zero
and INT_MAX. If it's too high then these sprintf()s will overflow.
Fixes: 203d3d4aa4 ("the generic thermal sysfs driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f61fe5f081cf40de08d0a4c89659baf23c900f0c ]
According to the definition of virtqueue coalescing spec[1]:
Upon disabling and re-enabling a transmit virtqueue, the device MUST set
the coalescing parameters of the virtqueue to those configured through the
VIRTIO_NET_CTRL_NOTF_COAL_TX_SET command, or, if the driver did not set
any TX coalescing parameters, to 0.
Upon disabling and re-enabling a receive virtqueue, the device MUST set
the coalescing parameters of the virtqueue to those configured through the
VIRTIO_NET_CTRL_NOTF_COAL_RX_SET command, or, if the driver did not set
any RX coalescing parameters, to 0.
We need to add this setting for vq resize (ethtool -G) where vq_reset happens.
[1] https://lists.oasis-open.org/archives/virtio-dev/202303/msg00415.html
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb2b3609162135625bf96acf5118051cd0d082e ]
When the user sets a non-zero coalescing parameter to 0 for a specific
virtqueue, it does not work as expected, so let's fix this.
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Reported-by: Xiaoming Zhao <zxm377917@alibaba-inc.com>
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9420838ab4ffb82850095549e94dcee3f7fe0cb ]
When using .set_coalesce interface to set all queue coalescing
parameters, we need to update both per-queue and global save values.
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134674c1877be5e35e35802517c67a9ecce21153 ]
Since virtio-net allows switching napi_tx for per txq, we have to
get the specific txq's result now.
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30fa41a0f6df4c85790cc6499ddc4a926a113bfa ]
None of the dump callbacks uses netlink_callback::args beyond the first
element, no need to zero the data.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
