[ Upstream commit f4346fb3ed ]
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58e16c752e ]
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97e4827d77 ]
cqspi_set_protocol() only set the data width, but ignored the command
and address width (except for 8-8-8 DTR ops), leading to corruption of
all transfers using 1-X-X or X-X-X ops. Fix by setting the other two
widths as well.
While we're at it, simplify the code a bit by replacing the
CQSPI_INST_TYPE_* constants with ilog2().
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash with 1-4-4
read and write operations.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220331110819.133392-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b423e54ba9 ]
All remaining skbs should be released when myri10ge_xmit fails to
transmit a packet. Fix it within another skb_list_walk_safe.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afb8e24652 ]
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be5802795c ]
Currently there are known potential issues for balloon and hot-add on
ARM64:
* Unballoon requests from Hyper-V should only unballoon ranges
that are guest page size aligned, otherwise guests cannot handle
because it's impossible to partially free a page. This is a
problem when guest page size > 4096 bytes.
* Memory hot-add requests from Hyper-V should provide the NUMA
node id of the added ranges or ARM64 should have a functional
memory_add_physaddr_to_nid(), otherwise the node id is missing
for add_memory().
These issues require discussions on design and implementation. In the
meanwhile, post_status() is working and essential to guest monitoring.
Therefore instead of disabling the entire hv_balloon driver, the
ballooning (when page size > 4096 bytes) and hot-add are disabled
accordingly for now. Once the issues are fixed, they can be re-enable in
these cases.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220325023212.1570049-3-boqun.feng@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1c4f93e3f ]
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2c0b0fbe0 ]
The alternatives code must be `noinstr` such that it does not patch itself,
as the cache invalidation is only performed after all the alternatives have
been applied.
Mark patch_alternative() as `noinstr`. Mark branch_insn_requires_update()
and get_alt_insn() with `__always_inline` since they are both only called
through patch_alternative().
Booting a kernel in QEMU TCG with KCSAN=y and ARM64_USE_LSE_ATOMICS=y caused
a boot hang:
[ 0.241121] CPU: All CPU(s) started at EL2
The alternatives code was patching the atomics in __tsan_read4() from LL/SC
atomics to LSE atomics.
The following fragment is using LL/SC atomics in the .text section:
| <__tsan_unaligned_read4+304>: ldxr x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This LL/SC atomic sequence was to be replaced with LSE atomics. However since
the alternatives code was instrumentable, __tsan_read4() was being called after
only the first instruction was replaced, which led to the following code in memory:
| <__tsan_unaligned_read4+304>: ldadd x5, x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This caused an infinite loop as the `stxr` instruction never completed successfully,
so `w7` was always 0.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20220405104733.11476-1-joey.gouly@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 070a88fd4a ]
This commit corrects the printing of the IPU clock error percentage if
it is between -0.1% to -0.9%. For example, if the pixel clock requested
is 27.2 MHz but only 27.0 MHz can be achieved the deviation is -0.8%.
But the fixed point math had a flaw and calculated error of 0.2%.
Before:
Clocks: IPU 270000000Hz DI 24716667Hz Needed 27200000Hz
IPU clock can give 27000000 with divider 10, error 0.2%
Want 27200000Hz IPU 270000000Hz DI 24716667Hz using IPU, 27000000Hz
After:
Clocks: IPU 270000000Hz DI 24716667Hz Needed 27200000Hz
IPU clock can give 27000000 with divider 10, error -0.8%
Want 27200000Hz IPU 270000000Hz DI 24716667Hz using IPU, 27000000Hz
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220207151411.5009-1-mark.jonas@de.bosch.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5399752299 ]
Samsung' 840 EVO with the latest firmware (EXT0DB6Q) locks up with
the a message: "READ LOG DMA EXT failed, trying PIO" during boot.
Initially this was discovered because it caused a crash
with the sata_dwc_460ex controller on a WD MyBook Live DUO.
The reporter "Tice Rex" which has the unique opportunity that he
has two Samsung 840 EVO SSD! One with the older firmware "EXT0BB0Q"
which booted fine and didn't expose "READ LOG DMA EXT". But the
newer/latest firmware "EXT0DB6Q" caused the headaches.
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3efcedd27 ]
KS8851_MLL selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL,
so make KS8851_MLL also depend on PTP_1588_CLOCK_OPTIONAL since
'select' does not follow any dependency chains.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851_MLL [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && HAS_IOMEM [=y]
ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0xb35): undefined reference to `ptp_clock_index'
ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x2586): undefined reference to `ptp_clock_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bade8e532 ]
The adapter request_limit is hardcoded to be INITIAL_SRP_LIMIT which is
currently an arbitrary value of 800. Increase this value to 1024 which
better matches the characteristics of the typical IBMi Initiator that
supports 32 LUNs and a queue depth of 32.
This change also has the secondary benefit of being a power of two as
required by the kfifo API. Since, Commit ab9bb6318b ("Partially revert
"kfifo: fix kfifo_alloc() and kfifo_init()"") the size of IU pool for each
target has been rounded down to 512 when attempting to kfifo_init() those
pools with the current request_limit size of 800.
Link: https://lore.kernel.org/r/20220322194443.678433-1-tyreld@linux.ibm.com
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df0101197c ]
When recovering from a pci-parity error the driver is failing to re-create
queues, causing recovery to fail. Looking deeper, it was found that the
interrupt vector count allocated on the recovery was fewer than the vectors
originally allocated. This disparity resulted in CPU map entries with stale
information. When the driver tries to re-create the queues, it attempts to
use the stale information which indicates an eq/interrupt vector that was
no longer created.
Fix by clearng the cpup map array before enabling and requesting the IRQs
in the lpfc_sli_reset_slot_s4 routine().
Link: https://lore.kernel.org/r/20220317032737.45308-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6cae15b57 ]
When reading a packet from a host-to-guest ring buffer, there is no
memory barrier between reading the write index (to see if there is
a packet to read) and reading the contents of the packet. The Hyper-V
host uses store-release when updating the write index to ensure that
writes of the packet data are completed first. On the guest side,
the processor can reorder and read the packet data before the write
index, and sometimes get stale packet data. Getting such stale packet
data has been observed in a reproducible case in a VM on ARM64.
Fix this by using virt_load_acquire() to read the write index,
ensuring that reads of the packet data cannot be reordered
before it. Preventing such reordering is logically correct, and
with this change, getting stale data can no longer be reproduced.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/1648394710-33480-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d21732475 ]
PCI pass-thru devices in a Hyper-V VM are represented as a VMBus
device and as a PCI device. The coherence of the VMbus device is
set based on the VMbus node in ACPI, but the PCI device has no
ACPI node and defaults to not hardware coherent. This results
in extra software coherence management overhead on ARM64 when
devices are hardware coherent.
Fix this by setting up the PCI host bus so that normal
PCI mechanisms will propagate the coherence of the VMbus
device to the PCI device. There's no effect on x86/x64 where
devices are always hardware coherent.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1648138492-2191-3-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebbb7bb9e8 ]
As the kmalloc_array() may return null, the 'event_waiters[i].wait' would lead to null-pointer dereference.
Therefore, it is better to check the return value of kmalloc_array() to avoid this confusion.
Signed-off-by: QintaoShen <unSimple1993@163.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7dfbd2e60 ]
Compute-only GPUs have more than 8 VMIDs allocated to KFD. Fix
this by passing correct number of VMIDs to HWS
v2: squash in warning fix (Alex)
Signed-off-by: Tushar Patel <tushar.patel@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b818a5d374 ]
If the GPU is passed through to a guest VM, use the PCI
BAR for CPU FB access rather than the physical address of
carve out. The physical address is not valid in a guest.
v2: Fix HDP handing as suggested by Michel
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7d16d9a07 ]
This is a long time leftover from when I originally added the free space
inode, the point was to catch cases where we weren't honoring the NOCOW
flag. However there exists a race with relocation, if we allocate our
free space inode in a block group that is about to be relocated, we
could trigger the COW path before the relocation has the opportunity to
find the extents and delete the free space cache. In production where
we have auto-relocation enabled we're seeing this WARN_ON_ONCE() around
5k times in a 2 week period, so not super common but enough that it's at
the top of our metrics.
We're properly handling the error here, and with us phasing out v1 space
cache anyway just drop the WARN_ON_ONCE.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05fd9564e9 ]
Since the initial introduction of (posix) fallocate back at the turn of
the century, it has been possible to use this syscall to change the
user-visible contents of files. This can happen by extending the file
size during a preallocation, or through any of the newer modes (punch,
zero range). Because the call can be used to change file contents, we
should treat it like we do any other modification to a file -- update
the mtime, and drop set[ug]id privileges/capabilities.
The VFS function file_modified() does all this for us if pass it a
locked inode, so let's make fallocate drop permissions correctly.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ef3342a93 ]
get_pf_vdev() tries to check if a PF is a VFIO PF by looking at the driver:
if (pci_dev_driver(physfn) != pci_dev_driver(vdev->pdev)) {
However now that we have multiple VF and PF drivers this is no longer
reliable.
This means that security tests realted to vf_token can be skipped by
mixing and matching different VFIO PCI drivers.
Instead of trying to use the driver core to find the PF devices maintain a
linked list of all PF vfio_pci_core_device's that we have called
pci_enable_sriov() on.
When registering a VF just search the list to see if the PF is present and
record the match permanently in the struct. PCI core locking prevents a PF
from passing pci_disable_sriov() while VF drivers are attached so the VFIO
owned PF becomes a static property of the VF.
In common cases where vfio does not own the PF the global list remains
empty and the VF's pointer is statically NULL.
This also fixes a lockdep splat from recursive locking of the
vfio_group::device_lock between vfio_device_get_from_name() and
vfio_device_get_from_dev(). If the VF and PF share the same group this
would deadlock.
Fixes: ff53edf6d6 ("vfio/pci: Split the pci_driver code out of vfio_pci_core.c")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/0-v3-876570980634+f2e8-vfio_vf_token_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce40426fdc ]
Mixing sched_clock() and ktime_get_ns() usage will give bad results.
Switch hst_select_path() from using sched_clock() to ktime_get_ns().
Also rename path_service_time()'s 'sched_now' variable to 'now'.
Fixes: 2613eab119 ("dm mpath: add Historical Service Time Path Selector")
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64c4a37ac0 ]
Smatch printed a warning:
arch/x86/crypto/poly1305_glue.c:198 poly1305_update_arch() error:
__memcpy() 'dctx->buf' too small (16 vs u32max)
It's caused because Smatch marks 'link_len' as untrusted since it comes
from sscanf(). Add a check to ensure that 'link_len' is not larger than
the size of the 'link_str' buffer.
Fixes: c69c1b6eae ("cifs: implement CIFSParseMFSymlink()")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d25045245 ]
AST2600 MAC register 0x58 is writable only when the MAC clock is
enabled. Usually, the MAC clock is enabled by the bootloader so
register 0x58 is set normally when the bootloader is involved. To make
ast2600 ftgmac100 work without the bootloader, postpone the register
write until the clock is ready.
Fixes: 137d23cea1 ("net: ftgmac100: Fix Aspeed ast2600 TX hang issue")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16b859872 ]
The MACVLAN receive handler clones skbs to all matching source MACVLAN
interfaces, before it passes the packet along to match on destination
based MACVLANs.
When using the MACVLAN nodst mode, passing the packet to destination based
MACVLANs is omitted and the handler returns with RX_HANDLER_CONSUMED.
However, the passed skb is not freed, leaking for any packet processed
with the nodst option.
Properly free the skb when consuming packets to fix that leak.
Fixes: 427f0c8c19 ("macvlan: Add nodst option to macvlan type source")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f034fc50d3 ]
Fix incorrect debug message:
Attempting to add event pmu 'intel_pt' with '' that may result in
non-fatal errors
which always appears with perf record -vv and intel_pt e.g.
perf record -vv -e intel_pt//u uname
The message is incorrect because there will never be non-fatal errors.
Suppress the message if the PMU is 'selectable' i.e. meant to be
selected directly as an event.
Fixes: 4ac22b484d ("perf parse-events: Make add PMU verbose output clearer")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lore.kernel.org/lkml/20220411061758.2458417-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24d0c9f0e7 ]
In the previous fix, we increased the max buffer bytes from 1MB to 4MB
so that we can use bigger buffers for the modern HiFi devices with
higher rates, more channels and wider formats. OTOH, extending this
has a concern that too big buffer is allowed for the lower rates, less
channels and narrower formats; when an application tries to allocate
as big buffer as possible, it'll lead to unexpectedly too huge size.
Also, we had a problem about the inconsistent max buffer and period
bytes for the implicit feedback mode when both streams have different
channels. This was fixed by the (relatively complex) patch to reduce
the max buffer and period bytes accordingly.
This is an alternative fix for those, a patch to kill two birds with
one stone (*): instead of increasing the max buffer bytes blindly and
applying the reduction per channels, we simply use the hw constraints
for the buffer and period "time". Meanwhile the max buffer and period
bytes are set unlimited instead.
Since the inconsistency of buffer (and period) bytes comes from the
difference of the channels in the tied streams, as long as we care
only about the buffer (and period) time, it doesn't matter; the buffer
time is same for different channels, although we still allow higher
buffer size. Similarly, this will allow more buffer bytes for HiFi
devices while it also keeps the reasonable size for the legacy
devices, too.
As of this patch, the max period and buffer time are set to 1 and 2
seconds, which should be large enough for all possible use cases.
(*) No animals were harmed in the making of this patch.
Fixes: 98c27add5d ("ALSA: usb-audio: Cap upper limits of buffer/period bytes for implicit fb")
Fixes: fee2ec8cce ("ALSA: usb-audio: Increase max buffer size")
Link: https://lore.kernel.org/r/20220412130740.18933-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce64763c63 ]
The selftest "mqueue/mq_perf_tests.c" use CPU_ALLOC to allocate
CPU set. This cpu set is used further in pthread_attr_setaffinity_np
and by pthread_create in the code. But in current code, allocated
cpu set is not freed.
Fix this issue by adding CPU_FREE in the "shutdown" function which
is called in most of the error/exit path for the cleanup. There are
few error paths which exit without using shutdown. Add a common goto
error path with CPU_FREE for these cases.
Fixes: 7820b0715b ("tools/selftests: add mq_perf_tests")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fb2719087 ]
The card destructor of nm256 driver does merely stopping the running
timer, and it's superfluous for the probe error handling. Moreover,
calling this via the previous devres change would lead to another
problem due to the reverse call order.
This patch moves the setup of the private_free callback after the card
registration, so that it can be used only after fully set up.
Fixes: aa92050f10 ("ALSA: mtpav: Allocate resources with device-managed APIs")
Link: https://lore.kernel.org/r/20220412102636.16000-39-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
