commit fdf35a6b22 upstream.
I noticed that the VT switch doesn't work any longer with a Dell
laptop with 1366x768 eDP when the machine is connected with a DP
monitor. It behaves as if VT were switched, but the graphics remain
frozen. Actually the keyboard works, so I could switch back to VT7
again.
I tried to track down the problem, and encountered a long story until
we reach to this error:
- The machine is booted with video=1366x768 option (the distro
installer seems to add it as default).
- Recently, drm_helper_probe_single_connector_modes() deals with
cmdline modes, and it tries to create a new mode when no
matching mode is found.
- The drm_mode_create_from_cmdline_mode() creates a mode based on
either CVT of GFT according to the given cmdline mode; in our case,
it's 1366x768.
- Since both CVT and GFT can't express the width 1366 due to
alignment, the resultant mode becomes 1368x768, slightly larger than
the given size.
- Later on, the atomic commit is performed, and in
drm_atomic_check_only(), the size of each plane is checked.
- The size check of 1366x768 fails due to the above, and eventually
the whole VT switch fails.
Back in the history, we've had a manual fix-up of 1368x768 in various
places via c09dedb7a5 ("drm/edid: Add a workaround for 1366x768 HD
panel"), but they have been all in drm_edid.c at probing the modes
from EDID. For addressing the problem above, we need a similar hack
to the mode newly created from cmdline, manually adjusting the width
when the expected size is 1366 while we get 1368 instead.
Fixes: eaf99c749d ("drm: Perform cmdline mode parsing during...")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109145614.29454-1-tiwai@suse.de
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68f458eec7 upstream.
Instead of scheduling the work to handle the initial delayed event, use 1s
delay.
This delay should not be needed, but Optimus/nouveau will fail in a
mysterious way if the delayed event is handled as soon as possible like it
is done in drm_helper_probe_single_connector_modes() in case the poll
was enabled before.
Reverting 339fd36238 would give back the 10 sec (!) delay to handle the
delayed event. Adding 1sec delay to the poll_work is enough to work around
the issue in Optimus setups and gives shorter response on handling the
initial delayed event.
Fixes: 339fd36238 ("drm: drm_probe_helper: Fix output_poll_work scheduling")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[danvet: Add FIXME to the comment to make it stick out more.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109143158.21917-1-peter.ujfalusi@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd7c99142d upstream.
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21f5eda9b8 upstream.
Since ef1b144d ("tools/virtio/ringtest: fix run-on-all.sh to work
without /dev/cpu") run-on-all.sh uses seq 0 $HOST_AFFINITY as the list
of ids of the CPUs to run the command on (assuming ids of online CPUs
are consecutive and start from 0), where $HOST_AFFINITY is the highest
CPU id in the system previously determined using lscpu. This can fail
on systems with offline CPUs.
Instead let's use lscpu to determine the list of online CPUs.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: ef1b144d ("tools/virtio/ringtest: fix run-on-all.sh to work without
/dev/cpu")
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36b29eb30e upstream.
Fix to return a negative error code from the kthread_run() error
handling case instead of 0, as done elsewhere in this function.
Fixes: cdd5de500b ("soc: ti: Add wkup_m3_ipc driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2dd8af00c upstream.
The commit 7c7289a404 ("spi: pxa2xx: Default thresholds to PXA
configuration") while splitting up CE4100 code obviously missed a break
condition in one chunk. Add it here.
Looks like we have no active user of CE4100, though better to fix this later
than never.
Fixes: commit 7c7289a404 ("spi: pxa2xx: Default thresholds to PXA configuration")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c9e6c2b2b upstream.
PL330 DMA engine driver is leaking a runtime reference after any terminated
DMA transactions. This patch fixes this issue by tracking runtime PM state
of the device and making additional call to pm_runtime_put() in terminate_all
callback if needed.
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0026c7bfb upstream.
Clock control indirectly requires access to MFC device, so call it only
if we are sure that the device exists in s5p_mfc_release function.
s5p_mfc_remove() calls s5p_mfc_final_pm(), which releases all PM related
resources, including clocks, so any call to clocks related functions
is not valid after s5p_mfc_final_pm().
Fixes: d695c12 ("[media] media: s5p-mfc fix invalid memory access from
s5p_mfc_release()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eadf081146 upstream.
A bugfix removed the two callers of s5p_cec_runtime_suspend
and s5p_cec_runtime_resume, leading to the return of a harmless
warning that I had previously fixed in commit aee8937089
("[media] s5p_cec: mark suspend/resume as __maybe_unused"):
staging/media/s5p-cec/s5p_cec.c:234:12: error: ‘s5p_cec_runtime_suspend’ defined but not used [-Werror=unused-function]
staging/media/s5p-cec/s5p_cec.c:242:12: error: ‘s5p_cec_runtime_resume’ defined but not used [-Werror=unused-function]
This adds the __maybe_unused annotations to the function that
were not removed and that are now unused when CONFIG_PM
is disabled.
Fixes: 57b978ada0 ("[media] s5p-cec: fix system and runtime PM integration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b2bed8912 upstream.
The devm_ioremap_resource() returns error pointers, never NULL. The
platform_get_resource() returns NULL on error, never error pointers.
The error code needs to be set, as well. The current code returns
PTR_ERR(NULL) which is success.
Fixes: 57b2c0628b ("[media] st-hva: multi-format video encoder V4L2 driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ec03e60ef upstream.
Function ite_set_carrier_params() uses variable use_demodulator after
having initialized it to false in some if branches, but this variable is
never set to true otherwise.
This bug has been found using clang -Wsometimes-uninitialized warning
flag.
Fixes: 620a32bba4 ("[media] rc: New rc-based ite-cir driver for
several ITE CIRs")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df94121f02 upstream.
It's not necessary to free memory allocated with devm_kzalloc
and using kfree leads to a double free.
Fixes: 7aae6e2df1 ("[media] Add GS1662 driver, a video serializer")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff681022c6 upstream.
Moving the pxa_camera driver from soc_camera lots the implied
VIDEO_V4L2 Kconfig dependency, and building the driver without
V4L2 results in a kernel that cannot link:
drivers/media/platform/pxa_camera.o: In function `pxa_camera_remove':
pxa_camera.c:(.text.pxa_camera_remove+0x10): undefined reference to `v4l2_clk_unregister'
pxa_camera.c:(.text.pxa_camera_remove+0x18): undefined reference to `v4l2_device_unregister'
drivers/media/platform/pxa_camera.o: In function `pxa_camera_probe':
pxa_camera.c:(.text.pxa_camera_probe+0x458): undefined reference to `v4l2_of_parse_endpoint'
drivers/media/v4l2-core/videobuf2-core.o: In function `__enqueue_in_driver':
drivers/media/v4l2-core/videobuf2-core.o: In function `vb2_core_streamon':
videobuf2-core.c:(.text.vb2_core_streamon+0x1b4): undefined reference to `v4l_vb2q_enable_media_source'
drivers/media/v4l2-core/videobuf2-v4l2.o: In function `vb2_ioctl_reqbufs':
videobuf2-v4l2.c:(.text.vb2_ioctl_reqbufs+0xc): undefined reference to `video_devdata'
This adds back an explicit dependency.
Fixes: 3050b99850 ("[media] media: platform: pxa_camera: move pxa_camera out of soc_camera")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9205e18b4 upstream.
devm_pinctrl_get() can fail so we should check for that.
Fixes: 0a6824bc10 ('[media] v4l2: blackfin: select proper pinctrl state in ppi_set_params if CONFIG_PINCTRL is enabled')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63447646ac upstream.
Since commit 4dffed5b3a ("rpmsg: Name rpmsg devices based on
channel id"), it is no more possible for a firmware to register twice
a service (on different endpoints). rpmsg_register_device function
is failing when calling device_add for the second time as second
device has the same name as first one already register.
It is because name is based only on service name and so is not more
unique. Previously name was unique thanks to the use of rpmsg_dev_index.
This patch adds destination and source endpoint numbers device name to
create an unique identifier.
Fixes: 4dffed5b3a ("rpmsg: Name rpmsg devices based on channel id")
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
[bjorn: flipped name and address in device name]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73613b16cb upstream.
This patch fixes the bug of devfreq_add_device(). The devfreq device must
have the default governor. If find_devfreq_governor() returns error,
devfreq_add_device() fail to add the devfreq instance.
Fixes: 1b5c1be2c8 (PM / devfreq: map devfreq drivers to governor using name)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32dd773169 upstream.
This patch fixes the wrong return value. If devfreq driver requires the wrong
and non-available governor, it is fail. So, this patch returns the error
insead of -EPROBE_DEFER.
Fixes: 403e0689d2 (PM / devfreq: exynos: Add support of bus frequency of sub-blocks using passive governor)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffb5845658 upstream.
mpt3sas has a firmware failure where it can only handle one pass through
ATA command at a time. If another comes in, contrary to the SAT
standard, it will hang until the first one completes (causing long
commands like secure erase to timeout). The original fix was to block
the device when an ATA command came in, but this caused a regression
with
commit 669f044170
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Nov 22 16:17:13 2016 -0800
scsi: srp_transport: Move queuecommand() wait code to SCSI core
So fix the original fix of the secure erase timeout by properly
returning SAM_STAT_BUSY like the SAT recommends. The original patch
also had a concurrency problem since scsih_qcmd is lockless at that
point (this is fixed by using atomic bitops to set and test the flag).
[mkp: addressed feedback wrt. test_bit and fixed whitespace]
Fixes: 18f6084a98 (mpt3sas: Fix secure erase premature termination)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff5d99225 upstream.
On architectures like arm64, swiotlb is tied intimately to the core
architecture DMA support. In addition, ZONE_DMA cannot be disabled.
To aid debugging and catch devices not supporting DMA to memory outside
the 32-bit address space, add a kernel command line option
"swiotlb=noforce", which disables the use of bounce buffers.
If specified, trying to map memory that cannot be used with DMA will
fail, and a rate-limited warning will be printed.
Note that io_tlb_nslabs is set to 1, which is the minimal supported
value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 524dabe1c6 upstream.
Commit b67a8b29df introduced logic to skip swiotlb allocation when all memory
is DMA accessible anyway.
While this is a great idea, __dma_alloc still calls swiotlb code unconditionally
to allocate memory when there is no CMA memory available. The swiotlb code is
called to ensure that we at least try get_free_pages().
Without initialization, swiotlb allocation code tries to access io_tlb_list
which is NULL. That results in a stack trace like this:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
[<ffff00000845b908>] swiotlb_tbl_map_single+0xd0/0x2b0
[<ffff00000845be94>] swiotlb_alloc_coherent+0x10c/0x198
[<ffff000008099dc0>] __dma_alloc+0x68/0x1a8
[<ffff000000a1b410>] drm_gem_cma_create+0x98/0x108 [drm]
[<ffff000000abcaac>] drm_fbdev_cma_create_with_funcs+0xbc/0x368 [drm_kms_helper]
[<ffff000000abcd84>] drm_fbdev_cma_create+0x2c/0x40 [drm_kms_helper]
[<ffff000000abc040>] drm_fb_helper_initial_config+0x238/0x410 [drm_kms_helper]
[<ffff000000abce88>] drm_fbdev_cma_init_with_funcs+0x98/0x160 [drm_kms_helper]
[<ffff000000abcf90>] drm_fbdev_cma_init+0x40/0x58 [drm_kms_helper]
[<ffff000000b47980>] vc4_kms_load+0x90/0xf0 [vc4]
[<ffff000000b46a94>] vc4_drm_bind+0xec/0x168 [vc4]
[...]
Thankfully swiotlb code just learned how to not do allocations with the FORCE_NO
option. This patch configures the swiotlb code to use that if we decide not to
initialize the swiotlb framework.
Fixes: b67a8b29df ("arm64: mm: only initialize swiotlb when necessary")
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Jisheng Zhang <jszhang@marvell.com>
CC: Geert Uytterhoeven <geert+renesas@glider.be>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c8a946bf3 upstream.
The arm64 __page_to_voff() macro takes a parameter called 'page', and
also refers to 'struct page'. Thus, if the value passed in is not
called 'page', we'll refer to the wrong struct name (which might not
exist).
Fixes: 3fa72fe9c6 ("arm64: mm: fix __page_to_voff definition")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Volodymyr Babchuk <Volodymyr_Babchuk@epam.com>
Signed-off-by: Oleksandr Andrushchenko <Oleksandr_Andrushchenko@epam.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d38de6564 upstream.
Verbs providers may perform house-keeping on the Send Queue during
each signaled send completion. It is necessary therefore for a verbs
consumer (like xprtrdma) to occasionally force a signaled send
completion if it runs unsignaled most of the time.
xprtrdma does not require signaled completions for Send or FastReg
Work Requests, but does signal some LocalInv Work Requests. To
ensure that Send Queue house-keeping can run before the Send Queue
is more than half-consumed, xprtrdma forces a signaled completion
on occasion by counting the number of Send Queue Entries it
consumes. It currently does this by counting each ib_post_send as
one Entry.
Commit c9918ff56d ("xprtrdma: Add ro_unmap_sync method for FRWR")
introduced the ability for frwr_op_unmap_sync to post more than one
Work Request with a single post_send. Thus the underlying assumption
of one Send Queue Entry per ib_post_send is no longer true.
Also, FastReg Work Requests are currently never signaled. They
should be signaled once in a while, just as Send is, to keep the
accounting of consumed SQEs accurate.
While we're here, convert the CQCOUNT macros to the currently
preferred kernel coding style, which is inline functions.
Fixes: c9918ff56d ("xprtrdma: Add ro_unmap_sync method for FRWR")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 124f930b8c upstream.
... otherwise the crypto stack will align it for us with a GFP_ATOMIC
allocation and a memcpy() -- see skcipher_walk_first().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2ed42517 upstream.
sparse says:
fs/ceph/inode.c:308:36: warning: incorrect type in argument 1 (different base types)
fs/ceph/inode.c:308:36: expected unsigned int [unsigned] [usertype] a
fs/ceph/inode.c:308:36: got restricted __le32 [usertype] frag
fs/ceph/inode.c:308:46: warning: incorrect type in argument 2 (different base types)
fs/ceph/inode.c:308:46: expected unsigned int [unsigned] [usertype] b
fs/ceph/inode.c:308:46: got restricted __le32 [usertype] frag
We need to convert these values to host-endian before calling the
comparator.
Fixes: a407846ef7 ("ceph: don't assume frag tree splits in mds reply are sorted")
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c341ee328 upstream.
try_get_cap_refs can be used as a condition in a wait_event* calls.
This is all fine until it has to call __ceph_do_pending_vmtruncate,
which in turn acquires the i_truncate_mutex. This leads to a situation
in which a task's state is !TASK_RUNNING and at the same time it's
trying to acquire a sleeping primitive. In essence a nested sleeping
primitives are being used. This causes the following warning:
WARNING: CPU: 22 PID: 11064 at kernel/sched/core.c:7631 __might_sleep+0x9f/0xb0()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff8109447d>] prepare_to_wait_event+0x5d/0x110
ipmi_msghandler tcp_scalable ib_qib dca ib_mad ib_core ib_addr ipv6
CPU: 22 PID: 11064 Comm: fs_checker.pl Tainted: G O 4.4.20-clouder2 #6
Hardware name: Supermicro X10DRi/X10DRi, BIOS 1.1a 10/16/2015
0000000000000000 ffff8838b416fa88 ffffffff812f4409 ffff8838b416fad0
ffffffff81a034f2 ffff8838b416fac0 ffffffff81052b46 ffffffff81a0432c
0000000000000061 0000000000000000 0000000000000000 ffff88167bda54a0
Call Trace:
[<ffffffff812f4409>] dump_stack+0x67/0x9e
[<ffffffff81052b46>] warn_slowpath_common+0x86/0xc0
[<ffffffff81052bcc>] warn_slowpath_fmt+0x4c/0x50
[<ffffffff8109447d>] ? prepare_to_wait_event+0x5d/0x110
[<ffffffff8109447d>] ? prepare_to_wait_event+0x5d/0x110
[<ffffffff8107767f>] __might_sleep+0x9f/0xb0
[<ffffffff81612d30>] mutex_lock+0x20/0x40
[<ffffffffa04eea14>] __ceph_do_pending_vmtruncate+0x44/0x1a0 [ceph]
[<ffffffffa04fa692>] try_get_cap_refs+0xa2/0x320 [ceph]
[<ffffffffa04fd6f5>] ceph_get_caps+0x255/0x2b0 [ceph]
[<ffffffff81094370>] ? wait_woken+0xb0/0xb0
[<ffffffffa04f2c11>] ceph_write_iter+0x2b1/0xde0 [ceph]
[<ffffffff81613f22>] ? schedule_timeout+0x202/0x260
[<ffffffff8117f01a>] ? kmem_cache_free+0x1ea/0x200
[<ffffffff811b46ce>] ? iput+0x9e/0x230
[<ffffffff81077632>] ? __might_sleep+0x52/0xb0
[<ffffffff81156147>] ? __might_fault+0x37/0x40
[<ffffffff8119e123>] ? cp_new_stat+0x153/0x170
[<ffffffff81198cfa>] __vfs_write+0xaa/0xe0
[<ffffffff81199369>] vfs_write+0xa9/0x190
[<ffffffff811b6d01>] ? set_close_on_exec+0x31/0x70
[<ffffffff8119a056>] SyS_write+0x46/0xa0
This happens since wait_event_interruptible can interfere with the
mutex locking code, since they both fiddle with the task state.
Fix the issue by using the newly-added nested blocking infrastructure
in 61ada528de ("sched/wait: Provide infrastructure to deal with
nested blocking")
Link: https://lwn.net/Articles/628628/
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90f92c631b upstream.
The following patch was sketched by Russell in response to my
crashes on the PB11MPCore after the patch for software-based
priviledged no access support for ARMv8.1. See this thread:
http://marc.info/?l=linux-arm-kernel&m=144051749807214&w=2
I am unsure what is going on, I suspect everyone involved in
the discussion is. I just want to repost this to get the
discussion restarted, as I still have to apply this patch
with every kernel iteration to get my PB11MPCore Realview
running.
Testing by Neil Armstrong on the Oxnas NAS has revealed that
this bug exist also on that widely deployed hardware, so
we are probably currently regressing all ARM11MPCore systems.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: a5e090acbf ("ARM: software-based priviledged-no-access support")
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0e8faa7a5 upstream.
This function clearly never worked and always returns true,
as pointed out by gcc-7:
arch/arm/mach-ux500/pm.c: In function 'prcmu_is_cpu_in_wfi':
arch/arm/mach-ux500/pm.c:137:212: error: ?:
using integer constants in boolean context, the expression
will always evaluate to 'true' [-Werror=int-in-bool-context]
With the added braces, the condition actually makes sense.
Fixes: 34fe6f107e ("mfd : Check if the other db8500 core is in WFI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ea6af3216 upstream.
This fixes commit ab8dd3aed0 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV") where the Card Detect and Write Protect
pins were improperly configured.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ab5c2b662 upstream.
This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)
The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.
Fixes: b32e700256 ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d37d41a14 upstream.
Commit d1f3156fc8 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: d1f3156fc8 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ab4c6183 upstream.
Commit 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce95077d0c upstream.
Commit 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9faa84cb9 upstream.
Commit 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c565d1a63 upstream.
Commit da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d8d6d3f2f upstream.
Commit f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9536fd30d4 upstream.
Commit 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ed80b3a23 upstream.
Commit 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
