[ Upstream commit 92717c2356 ]
In case the QCA7000 is not available via SPI (e.g. in reset),
the driver will cause a high load. The reason for this is
that the synchronization is never finished and schedule()
is never called. Since the synchronization is not timing
critical, it's safe to drop this from the scheduling condition.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f015b900bc ]
With offloading enabled, esp_xmit() gets invoked very late, from within
validate_xmit_xfrm() which is after validate_xmit_skb() validates and
linearizes the skb if the underlying device does not support fragments.
esp_output_tail() may add a fragment to the skb while adding the auth
tag/ IV. Devices without the proper support will then send skb->data
points to with the correct length so the packet will have garbage at the
end. A pcap sniffer will claim that the proper data has been sent since
it parses the skb properly.
It is not affected with INET_ESP_OFFLOAD disabled.
Linearize the skb after offloading if the sending hardware requires it.
It was tested on v4, v6 has been adopted.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7a2fc1437 ]
There are some MD5 tests which fail when the kernel is in FIPS mode,
since MD5 is not FIPS compliant. Add a check and only run those tests
if FIPS mode is not enabled.
Fixes: f0bee1ebb5 ("fcnal-test: Add TCP MD5 tests")
Fixes: 5cad8bce26 ("fcnal-test: Add TCP MD5 tests for VRF")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb43c60e64 ]
The vrf-xfrm-tests tests use the hmac(md5) and cbc(des3_ede)
algorithms for performing authentication and encryption, respectively.
This causes the tests to fail when fips=1 is set, since these algorithms
are not allowed in FIPS mode. Therefore, switch from hmac(md5) and
cbc(des3_ede) to hmac(sha1) and cbc(aes), which are FIPS compliant.
Fixes: 3f251d7411 ("selftests: Add tests for vrf and xfrms")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 713274f1f2 ]
The following scenario describes a bug in the verifier where it
incorrectly concludes about equivalent scalar IDs which could lead to
verifier bypass in privileged mode:
1. Prepare a 32-bit rogue number.
2. Put the rogue number into the upper half of a 64-bit register, and
roll a random (unknown to the verifier) bit in the lower half. The
rest of the bits should be zero (although variations are possible).
3. Assign an ID to the register by MOVing it to another arbitrary
register.
4. Perform a 32-bit spill of the register, then perform a 32-bit fill to
another register. Due to a bug in the verifier, the ID will be
preserved, although the new register will contain only the lower 32
bits, i.e. all zeros except one random bit.
At this point there are two registers with different values but the same
ID, which means the integrity of the verifier state has been corrupted.
5. Compare the new 32-bit register with 0. In the branch where it's
equal to 0, the verifier will believe that the original 64-bit
register is also 0, because it has the same ID, but its actual value
still contains the rogue number in the upper half.
Some optimizations of the verifier prevent the actual bypass, so
extra care is needed: the comparison must be between two registers,
and both branches must be reachable (this is why one random bit is
needed). Both branches are still suitable for the bypass.
6. Right shift the original register by 32 bits to pop the rogue number.
7. Use the rogue number as an offset with any pointer. The verifier will
believe that the offset is 0, while in reality it's the given number.
The fix is similar to the 32-bit BPF_MOV handling in check_alu_op for
SCALAR_VALUE. If the spill is narrowing the actual register value, don't
keep the ID, make sure it's reset to 0.
Fixes: 354e8f1970 ("bpf: Support <8-byte scalar spill and refill")
Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Andrii Nakryiko <andrii@kernel.org> # Checked veristat delta
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230607123951.558971-2-maxtram95@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecdf985d76 ]
For aligned stack writes using BPF_ST instruction track stored values
in a same way BPF_STX is handled, e.g. make sure that the following
commands produce similar verifier knowledge:
fp[-8] = 42; r1 = 42;
fp[-8] = r1;
This covers two cases:
- non-null values written to stack are stored as spill of fake
registers;
- null values written to stack are stored as STACK_ZERO marks.
Previously both cases above used STACK_MISC marks instead.
Some verifier test cases relied on the old logic to obtain STACK_MISC
marks for some stack values. These test cases are updated in the same
commit to avoid failures during bisect.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20230214232030.1502829-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 713274f1f2 ("bpf: Fix verifier id tracking of scalars on spill")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a287f5b0cf ]
This change adds methods in the XFRM-I input path that ensures that
policies are checked prior to processing of the subsequent decapsulated
packet, after which the relevant policies may no longer be resolvable
(due to changing src/dst/proto/etc).
Notably, raw ESP/AH packets did not perform policy checks inherently,
whereas all other encapsulated packets (UDP, TCP encapsulated) do policy
checks after calling xfrm_input handling in the respective encapsulation
layer.
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Test: Verified with additional Android Kernel Unit tests
Test: Verified against Android CTS
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f8b6df6a9 ]
This change allows inbound traffic through nested IPsec tunnels to
successfully match policies and templates, while retaining the secpath
stack trace as necessary for netfilter policies.
Specifically, this patch marks secpath entries that have already matched
against a relevant policy as having been verified, allowing it to be
treated as optional and skipped after a tunnel decapsulation (during
which the src/dst/proto/etc may have changed, and the correct policy
chain no long be resolvable).
This approach is taken as opposed to the iteration in b0355dbbf1,
where the secpath was cleared, since that breaks subsequent validations
that rely on the existence of the secpath entries (netfilter policies, or
transport-in-tunnel mode, where policies remain resolvable).
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Test: Tested against Android Kernel Unit Tests
Test: Tested against Android CTS
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d082d48737 upstream.
KPTI keeps around two PGDs: one for userspace and another for the
kernel. Among other things, set_pgd() contains infrastructure to
ensure that updates to the kernel PGD are reflected in the user PGD
as well.
One side-effect of this is that set_pgd() expects to be passed whole
pages. Unfortunately, init_trampoline_kaslr() passes in a single entry:
'trampoline_pgd_entry'.
When KPTI is on, set_pgd() will update 'trampoline_pgd_entry' (an
8-Byte globally stored [.bss] variable) and will then proceed to
replicate that value into the non-existent neighboring user page
(located +4k away), leading to the corruption of other global [.bss]
stored variables.
Fix it by directly assigning 'trampoline_pgd_entry' and avoiding
set_pgd().
[ dhansen: tweak subject and changelog ]
Fixes: 0925dda596 ("x86/mm/KASLR: Use only one PUD entry for real mode trampoline")
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/20230614163859.924309-1-lee@kernel.org/g
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782e53d0c1 upstream.
In a syzbot stress test that deliberately causes file system errors on
nilfs2 with a corrupted disk image, it has been reported that
nilfs_clear_dirty_page() called from nilfs_clear_dirty_pages() can cause a
general protection fault.
In nilfs_clear_dirty_pages(), when looking up dirty pages from the page
cache and calling nilfs_clear_dirty_page() for each dirty page/folio
retrieved, the back reference from the argument page to "mapping" may have
been changed to NULL (and possibly others). It is necessary to check this
after locking the page/folio.
So, fix this issue by not calling nilfs_clear_dirty_page() on a page/folio
after locking it in nilfs_clear_dirty_pages() if the back reference
"mapping" from the page/folio is different from the "mapping" that held
the page/folio just before.
Link: https://lkml.kernel.org/r/20230612021456.3682-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+53369d11851d8f26735c@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/000000000000da4f6b05eb9bf593@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 78d0d2063b upstream.
We cannot sanely handle partial retries for recvmsg if we have cmsg
attached. If we don't, then we'd just be overwriting the initial cmsg
header on retries. Alternatively we could increment and handle this
appropriately, but it doesn't seem worth the complication.
Move the MSG_WAITALL check into the non-multishot case while at it,
since MSG_WAITALL is explicitly disabled for multishot anyway.
Link: https://lore.kernel.org/io-uring/0b0d4411-c8fd-4272-770b-e030af6919a0@kernel.dk/
Cc: stable@vger.kernel.org # 5.10+
Reported-by: Stefan Metzmacher <metze@samba.org>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b1dc492087 upstream.
If we have cmsg attached AND we transferred partial data at least, clear
msg_controllen on retry so we don't attempt to send that again.
Cc: stable@vger.kernel.org # 5.10+
Fixes: cac9e4418f ("io_uring/net: save msghdr->msg_control for retries")
Reported-by: Stefan Metzmacher <metze@samba.org>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cac9e4418f upstream.
If the application sets ->msg_control and we have to later retry this
command, or if it got queued with IOSQE_ASYNC to begin with, then we
need to retain the original msg_control value. This is due to the net
stack overwriting this field with an in-kernel pointer, to copy it
in. Hitting that path for the second time will now fail the copy from
user, as it's attempting to copy from a non-user address.
Cc: stable@vger.kernel.org # 5.10+
Link: https://github.com/axboe/liburing/issues/880
Reported-and-tested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54abe19e00 upstream.
When commit 19343b5bdd ("mm/page-writeback: introduce tracepoint for
wait_on_page_writeback()") repurposed the writeback_dirty_page trace event
as a template to create its new wait_on_page_writeback trace event, it
ended up opening a window to NULL pointer dereference crashes due to the
(infrequent) occurrence of a race where an access to a page in the
swap-cache happens concurrently with the moment this page is being written
to disk and the tracepoint is enabled:
BUG: kernel NULL pointer dereference, address: 0000000000000040
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 800000010ec0a067 P4D 800000010ec0a067 PUD 102353067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 1320 Comm: shmem-worker Kdump: loaded Not tainted 6.4.0-rc5+ #13
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20230301gitf80f052277c8-1.fc37 03/01/2023
RIP: 0010:trace_event_raw_event_writeback_folio_template+0x76/0xf0
Code: 4d 85 e4 74 5c 49 8b 3c 24 e8 06 98 ee ff 48 89 c7 e8 9e 8b ee ff ba 20 00 00 00 48 89 ef 48 89 c6 e8 fe d4 1a 00 49 8b 04 24 <48> 8b 40 40 48 89 43 28 49 8b 45 20 48 89 e7 48 89 43 30 e8 a2 4d
RSP: 0000:ffffaad580b6fb60 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff90e38035c01c RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff90e38035c044
RBP: ffff90e38035c024 R08: 0000000000000002 R09: 0000000000000006
R10: ffff90e38035c02e R11: 0000000000000020 R12: ffff90e380bac000
R13: ffffe3a7456d9200 R14: 0000000000001b81 R15: ffffe3a7456d9200
FS: 00007f2e4e8a15c0(0000) GS:ffff90e3fbc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000040 CR3: 00000001150c6003 CR4: 0000000000170ee0
Call Trace:
<TASK>
? __die+0x20/0x70
? page_fault_oops+0x76/0x170
? kernelmode_fixup_or_oops+0x84/0x110
? exc_page_fault+0x65/0x150
? asm_exc_page_fault+0x22/0x30
? trace_event_raw_event_writeback_folio_template+0x76/0xf0
folio_wait_writeback+0x6b/0x80
shmem_swapin_folio+0x24a/0x500
? filemap_get_entry+0xe3/0x140
shmem_get_folio_gfp+0x36e/0x7c0
? find_busiest_group+0x43/0x1a0
shmem_fault+0x76/0x2a0
? __update_load_avg_cfs_rq+0x281/0x2f0
__do_fault+0x33/0x130
do_read_fault+0x118/0x160
do_pte_missing+0x1ed/0x2a0
__handle_mm_fault+0x566/0x630
handle_mm_fault+0x91/0x210
do_user_addr_fault+0x22c/0x740
exc_page_fault+0x65/0x150
asm_exc_page_fault+0x22/0x30
This problem arises from the fact that the repurposed writeback_dirty_page
trace event code was written assuming that every pointer to mapping
(struct address_space) would come from a file-mapped page-cache object,
thus mapping->host would always be populated, and that was a valid case
before commit 19343b5bdd. The swap-cache address space
(swapper_spaces), however, doesn't populate its ->host (struct inode)
pointer, thus leading to the crashes in the corner-case aforementioned.
commit 19343b5bdd ended up breaking the assignment of __entry->name and
__entry->ino for the wait_on_page_writeback tracepoint -- both dependent
on mapping->host carrying a pointer to a valid inode. The assignment of
__entry->name was fixed by commit 68f23b8906 ("memcg: fix a crash in
wb_workfn when a device disappears"), and this commit fixes the remaining
case, for __entry->ino.
Link: https://lkml.kernel.org/r/20230606233613.1290819-1-aquini@redhat.com
Fixes: 19343b5bdd ("mm/page-writeback: introduce tracepoint for wait_on_page_writeback()")
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Reviewed-by: Yafang Shao <laoar.shao@gmail.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8e796895e ]
The max_raw_write member of the regmap_spi_avmm_bus structure is defined
as:
.max_raw_write = SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
SPI_AVMM_VAL_SIZE == 4 and MAX_WRITE_CNT == 1 so this results in a
maximum write transfer size of 4 bytes which provides only enough space to
transfer the address of the target register. It provides no space for the
value to be transferred. This bug became an issue (divide-by-zero in
_regmap_raw_write()) after the following was accepted into mainline:
commit 3981514180 ("regmap: Account for register length when chunking")
Change max_raw_write to include space (4 additional bytes) for both the
register address and value:
.max_raw_write = SPI_AVMM_REG_SIZE + SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
Fixes: 7f9fb67358 ("regmap: add Intel SPI Slave to AVMM Bus Bridge support")
Reviewed-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20230620202824.380313-1-russell.h.weight@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e6f9e590b7 upstream.
While SDHCI claims to support 64-bit DMA on MSM8916 it does not seem to
be properly functional. It is not immediately obvious because SDHCI is
usually used with IOMMU bypassed on this SoC, and all physical memory
has 32-bit addresses. But when trying to enable the IOMMU it quickly
fails with an error such as the following:
arm-smmu 1e00000.iommu: Unhandled context fault:
fsr=0x402, iova=0xfffff200, fsynr=0xe0000, cbfrsynra=0x140, cb=3
mmc1: ADMA error: 0x02000000
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00002e02
mmc1: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc1: sdhci: Present: 0x03f80206 | Host ctl: 0x00000019
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007
mmc1: sdhci: Timeout: 0x0000000a | Int stat: 0x00000001
mmc1: sdhci: Int enab: 0x03ff900b | Sig enab: 0x03ff100b
mmc1: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x00008007
mmc1: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000
mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x5b590000
mmc1: sdhci: Resp[2]: 0xe6487f80 | Resp[3]: 0x0a404094
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0x0000000ffffff224
mmc1: sdhci_msm: ----------- VENDOR REGISTER DUMP -----------
mmc1: sdhci_msm: DLL sts: 0x00000000 | DLL cfg: 0x60006400 | DLL cfg2: 0x00000000
mmc1: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl: 0x00000000 | DDR cfg: 0x00000000
mmc1: sdhci_msm: Vndr func: 0x00018a9c | Vndr func2 : 0xf88018a8 Vndr func3: 0x00000000
mmc1: sdhci: ============================================
mmc1: sdhci: fffffffff200: DMA 0x0000ffffffffe100, LEN 0x0008, Attr=0x21
mmc1: sdhci: fffffffff20c: DMA 0x0000000000000000, LEN 0x0000, Attr=0x03
Looking closely it's obvious that only the 32-bit part of the address
(0xfffff200) arrives at the SMMU, the higher 16-bit (0xffff...) get
lost somewhere. This might not be a limitation of the SDHCI itself but
perhaps the bus/interconnect it is connected to, or even the connection
to the SMMU.
Work around this by setting SDHCI_QUIRK2_BROKEN_64_BIT_DMA to avoid
using 64-bit addresses.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230518-msm8916-64bit-v1-1-5694b0f35211@gerhold.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f363f5aa8 upstream.
We found a refcount UAF bug as follows:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 1 PID: 342 at lib/refcount.c:25 refcount_warn_saturate+0xa0/0x148
Workqueue: events cpuset_hotplug_workfn
Call trace:
refcount_warn_saturate+0xa0/0x148
__refcount_add.constprop.0+0x5c/0x80
css_task_iter_advance_css_set+0xd8/0x210
css_task_iter_advance+0xa8/0x120
css_task_iter_next+0x94/0x158
update_tasks_root_domain+0x58/0x98
rebuild_root_domains+0xa0/0x1b0
rebuild_sched_domains_locked+0x144/0x188
cpuset_hotplug_workfn+0x138/0x5a0
process_one_work+0x1e8/0x448
worker_thread+0x228/0x3e0
kthread+0xe0/0xf0
ret_from_fork+0x10/0x20
then a kernel panic will be triggered as below:
Unable to handle kernel paging request at virtual address 00000000c0000010
Call trace:
cgroup_apply_control_disable+0xa4/0x16c
rebind_subsystems+0x224/0x590
cgroup_destroy_root+0x64/0x2e0
css_free_rwork_fn+0x198/0x2a0
process_one_work+0x1d4/0x4bc
worker_thread+0x158/0x410
kthread+0x108/0x13c
ret_from_fork+0x10/0x18
The race that cause this bug can be shown as below:
(hotplug cpu) | (umount cpuset)
mutex_lock(&cpuset_mutex) | mutex_lock(&cgroup_mutex)
cpuset_hotplug_workfn |
rebuild_root_domains | rebind_subsystems
update_tasks_root_domain | spin_lock_irq(&css_set_lock)
css_task_iter_start | list_move_tail(&cset->e_cset_node[ss->id]
while(css_task_iter_next) | &dcgrp->e_csets[ss->id]);
css_task_iter_end | spin_unlock_irq(&css_set_lock)
mutex_unlock(&cpuset_mutex) | mutex_unlock(&cgroup_mutex)
Inside css_task_iter_start/next/end, css_set_lock is hold and then
released, so when iterating task(left side), the css_set may be moved to
another list(right side), then it->cset_head points to the old list head
and it->cset_pos->next points to the head node of new list, which can't
be used as struct css_set.
To fix this issue, switch from all css_sets to only scgrp's css_sets to
patch in-flight iterators to preserve correct iteration, and then
update it->cset_head as well.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://www.spinics.net/lists/cgroups/msg37935.html
Suggested-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/all/20230526114139.70274-1-xiujianfeng@huaweicloud.com/
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Fixes: 2d8f243a5e ("cgroup: implement cgroup->e_csets[]")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2738d5ab79 upstream.
When the host tries to remove a PCI device, the host first sends a
PCI_EJECT message to the guest, and the guest is supposed to gracefully
remove the PCI device and send a PCI_EJECTION_COMPLETE message to the host;
the host then sends a VMBus message CHANNELMSG_RESCIND_CHANNELOFFER to
the guest (when the guest receives this message, the device is already
unassigned from the guest) and the guest can do some final cleanup work;
if the guest fails to respond to the PCI_EJECT message within one minute,
the host sends the VMBus message CHANNELMSG_RESCIND_CHANNELOFFER and
removes the PCI device forcibly.
In the case of fast device addition/removal, it's possible that the PCI
device driver is still configuring MSI-X interrupts when the guest receives
the PCI_EJECT message; the channel callback calls hv_pci_eject_device(),
which sets hpdev->state to hv_pcichild_ejecting, and schedules a work
hv_eject_device_work(); if the PCI device driver is calling
pci_alloc_irq_vectors() -> ... -> hv_compose_msi_msg(), we can break the
while loop in hv_compose_msi_msg() due to the updated hpdev->state, and
leave data->chip_data with its default value of NULL; later, when the PCI
device driver calls request_irq() -> ... -> hv_irq_unmask(), the guest
crashes in hv_arch_irq_unmask() due to data->chip_data being NULL.
Fix the issue by not testing hpdev->state in the while loop: when the
guest receives PCI_EJECT, the device is still assigned to the guest, and
the guest has one minute to finish the device removal gracefully. We don't
really need to (and we should not) test hpdev->state in the loop.
Fixes: de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-3-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a847234e24 upstream.
This reverts commit d6af2ed29c.
The statement "the hv_pci_bus_exit() call releases structures of all its
child devices" in commit d6af2ed29c is not true: in the path
hv_pci_probe() -> hv_pci_enter_d0() -> hv_pci_bus_exit(hdev, true): the
parameter "keep_devs" is true, so hv_pci_bus_exit() does *not* release the
child "struct hv_pci_dev *hpdev" that is created earlier in
pci_devices_present_work() -> new_pcichild_device().
The commit d6af2ed29c was originally made in July 2020 for RHEL 7.7,
where the old version of hv_pci_bus_exit() was used; when the commit was
rebased and merged into the upstream, people didn't notice that it's
not really necessary. The commit itself doesn't cause any issue, but it
makes hv_pci_probe() more complicated. Revert it to facilitate some
upcoming changes to hv_pci_probe().
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Wei Hu <weh@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-5-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 440b5e3663 upstream.
Since day 1 of the driver, there has been a race between
hv_pci_query_relations() and survey_child_resources(): during fast
device hotplug, hv_pci_query_relations() may error out due to
device-remove and the stack variable 'comp' is no longer valid;
however, pci_devices_present_work() -> survey_child_resources() ->
complete() may be running on another CPU and accessing the no-longer-valid
'comp'. Fix the race by flushing the workqueue before we exit from
hv_pci_query_relations().
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-2-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 320805ab61 upstream.
vmbus_wait_for_unload() may be called in the panic path after other
CPUs are stopped. vmbus_wait_for_unload() currently loops through
online CPUs looking for the UNLOAD response message. But the values of
CONFIG_KEXEC_CORE and crash_kexec_post_notifiers affect the path used
to stop the other CPUs, and in one of the paths the stopped CPUs
are removed from cpu_online_mask. This removal happens in both
x86/x64 and arm64 architectures. In such a case, vmbus_wait_for_unload()
only checks the panic'ing CPU, and misses the UNLOAD response message
except when the panic'ing CPU is CPU 0. vmbus_wait_for_unload()
eventually times out, but only after waiting 100 seconds.
Fix this by looping through *present* CPUs in vmbus_wait_for_unload().
The cpu_present_mask is not modified by stopping the other CPUs in the
panic path, nor should it be.
Also, in a CoCo VM the synic_message_page is not allocated in
hv_synic_alloc(), but is set and cleared in hv_synic_enable_regs()
and hv_synic_disable_regs() such that it is set only when the CPU is
online. If not all present CPUs are online when vmbus_wait_for_unload()
is called, the synic_message_page might be NULL. Add a check for this.
Fixes: cd95aad557 ("Drivers: hv: vmbus: handle various crash scenarios")
Cc: stable@vger.kernel.org
Reported-by: John Starks <jostarks@microsoft.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1684422832-38476-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 679bd7ebdd upstream.
As a result of analysis of a syzbot report, it turned out that in three
cases where nilfs2 allocates block device buffers directly via sb_getblk,
concurrent reads to the device can corrupt the allocated buffers.
Nilfs2 uses sb_getblk for segment summary blocks, that make up a log
header, and the super root block, that is the trailer, and when moving and
writing the second super block after fs resize.
In any of these, since the uptodate flag is not set when storing metadata
to be written in the allocated buffers, the stored metadata will be
overwritten if a device read of the same block occurs concurrently before
the write. This causes metadata corruption and misbehavior in the log
write itself, causing warnings in nilfs_btree_assign() as reported.
Fix these issues by setting an uptodate flag on the buffer head on the
first or before modifying each buffer obtained with sb_getblk, and
clearing the flag on failure.
When setting the uptodate flag, the lock_buffer/unlock_buffer pair is used
to perform necessary exclusive control, and the buffer is filled to ensure
that uninitialized bytes are not mixed into the data read from others. As
for buffers for segment summary blocks, they are filled incrementally, so
if the uptodate flag was unset on their allocation, set the flag and zero
fill the buffer once at that point.
Also, regarding the superblock move routine, the starting point of the
memset call to zerofill the block is incorrectly specified, which can
cause a buffer overflow on file systems with block sizes greater than
4KiB. In addition, if the superblock is moved within a large block, it is
necessary to assume the possibility that the data in the superblock will
be destroyed by zero-filling before copying. So fix these potential
issues as well.
Link: https://lkml.kernel.org/r/20230609035732.20426-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+31837fe952932efc8fb9@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000030000a05e981f475@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47867f0a7e upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the MPTCP MIB counters introduced in commit fc518953bc
("mptcp: add and use MIB counter infrastructure") and more later. The
MPTCP Join selftest heavily relies on these counters.
If a counter is not supported by the kernel, it is not displayed when
using 'nstat -z'. We can then detect that and skip the verification. A
new helper (get_counter()) has been added to do the required checks and
return an error if the counter is not available.
Note that if we expect to have these features available and if
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, the tests
will be marked as failed instead of skipped.
This new helper also makes sure we get the exact counter we want to
avoid issues we had in the past, e.g. with MPTcpExtRmAddr and
MPTcpExtRmAddrDrop sharing the same prefix. While at it, we uniform the
way we fetch a MIB counter.
Note for the backports: we rarely change these modified blocks so if
there is are conflicts, it is very likely because a counter is not used
in the older kernels and we don't need that chunk.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: b08fbf2410 ("selftests: add test-cases for MPTCP MP_JOIN")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2177d0b08e upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the checks of the default limits returned by the MPTCP
in-kernel path-manager. The default values have been modified by commit
72bcbc46a5 ("mptcp: increase default max additional subflows to 2").
Instead of comparing with hardcoded values, we can get the default one
and compare with them.
Note that if we expect to have the latest version, we continue to check
the hardcoded values to avoid unexpected behaviour changes.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: eedbc68532 ("selftests: add PM netlink functional tests")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1a6a38ab8 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
A new function is now available to easily detect if a feature is
missing by looking at the kernel version. That's clearly not ideal and
this kind of check should be avoided as soon as possible. But sometimes,
there are no external sign that a "feature" is available or not:
internal behaviours can change without modifying the uAPI and these
selftests are verifying the internal behaviours. Sometimes, the only
(easy) way to verify if the feature is present is to run the test but
then the validation cannot determine if there is a failure with the
feature or if the feature is missing. Then it looks better to check the
kernel version instead of having tests that can never fail. In any case,
we need a solution not to have a whole selftest being marked as failed
just because one sub-test has failed.
Note that this env var car be set to 1 not to do such check and run the
linked sub-test: SELFTESTS_MPTCP_LIB_NO_KVERSION_CHECK.
This new helper is going to be used in the following commits. In order
to ease the backport of such future patches, it would be good if this
patch is backported up to the introduction of MPTCP selftests, hence the
Fixes tag below: this type of check was supposed to be done from the
beginning.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 673004821a upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
New functions are now available to easily detect if a certain feature is
missing by looking at kallsyms.
These new helpers are going to be used in the following commits. In
order to ease the backport of such future patches, it would be good if
this patch is backported up to the introduction of MPTCP selftests,
hence the Fixes tag below: this type of check was supposed to be done
from the beginning.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13bb06f8dd upstream.
The tick period is aligned very early while the first clock_event_device is
registered. At that point the system runs in periodic mode and switches
later to one-shot mode if possible.
The next wake-up event is programmed based on the aligned value
(tick_next_period) but the delta value, that is used to program the
clock_event_device, is computed based on ktime_get().
With the subtracted offset, the device fires earlier than the exact time
frame. With a large enough offset the system programs the timer for the
next wake-up and the remaining time left is too small to make any boot
progress. The system hangs.
Move the alignment later to the setup of tick_sched timer. At this point
the system switches to oneshot mode and a high resolution clocksource is
available. At this point it is safe to align tick_next_period because
ktime_get() will now return accurate (not jiffies based) time.
[bigeasy: Patch description + testing].
Fixes: e9523a0d81 ("tick/common: Align tick period with the HZ tick.")
Reported-by: Mathias Krause <minipli@grsecurity.net>
Reported-by: "Bhatnagar, Rishabh" <risbhat@amazon.com>
Suggested-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Mathias Krause <minipli@grsecurity.net>
Acked-by: SeongJae Park <sj@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/5a56290d-806e-b9a5-f37c-f21958b5a8c0@grsecurity.net
Link: https://lore.kernel.org/12c6f9a3-d087-b824-0d05-0d18c9bc1bf3@amazon.com
Link: https://lore.kernel.org/r/20230615091830.RxMV2xf_@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e18eb8783e upstream.
Currently the tracing_reset_all_online_cpus() requires the
trace_types_lock held. But only one caller of this function actually has
that lock held before calling it, and the other just takes the lock so
that it can call it. More users of this function is needed where the lock
is not held.
Add a tracing_reset_all_online_cpus_unlocked() function for the one use
case that calls it without being held, and also add a lockdep_assert to
make sure it is held when called.
Then have tracing_reset_all_online_cpus() take the lock internally, such
that callers do not need to worry about taking it.
Link: https://lkml.kernel.org/r/20221123192741.658273220@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
