IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-5-pkshih@realtek.com
When we are going to do RF calibrations, they need BB helpers to control
TX PLCP, power, path and mode. Also, it they need helpers to backup and
restore some registers before and after RF calibrations. Then, use flow of
RF calibrations will be like backup registers, configure calibration,
configure TX parameters, measure calibration result, and finally restore
registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-9-pkshih@realtek.com
We need power on function to enable hardware circuits of MAC/BB/RF, and
then download firmware and load PHY parameters. After more settings, it
starts to work. When it enters idle, use power off function to have the
lowest power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-3-pkshih@realtek.com
This chip_ops is to assist set_channel, because we need setup and restore
hardware before and after set_channel.
Before set_channel, we stop transmitting, reset PPDU status, disable TSSI,
and disable ADC. After set_channel, do opposite things in reverse order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-2-pkshih@realtek.com
The wifi + bluetooth combo chips (RTL8723AU and RTL8723BU) read the
chip vendor from the wrong register because the val32 variable gets
overwritten. Add one more variable to avoid this.
This had no real effect on RTL8723BU. It may have had an effect on
RTL8723AU.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/24af8024-2f07-552b-93d8-38823d8e3cb0@gmail.com
Change active scan behavior to fit 6GHz requirements. There are many
different rules on active scan between 6GHz and 2GHz/5GHz, so if the
SSID is not specified, do fast passive scanning and limit number of
probe requests we send for now until new firmware can support all
rules.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221007045900.10823-1-pkshih@realtek.com
set_channel is main function to configure channel and bandwidth for all
layers, namely MAC, BB and RF. Additionally, MAC layer enables CCK rate
checking to avoid wrong rate from driver. BB layer configures SCO
(Sample Clock Offset) for CCK, TX gain error/offset, and reset baseband
hardware circuit after all configurations done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-7-pkshih@realtek.com
By accident, the previous patch duplicated the initialization
of the wake_tx_queue callback. Fix that by removing the new
initializations.
Fixes: a790cc3a4f ("wifi: mac80211: add wake_tx_queue callback to drivers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All drivers are now using mac80211 internal queues (iTXQs).
Drop mac80211 internal support for the old push path.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start to align the TX handling to only use internal TX queues (iTXQs):
Provide a handler for drivers not having a custom wake_tx_queue
callback and update the documentation.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of 4way handshake offload, transition disable policy
updated by the AP during EAPOL 3/4 is not updated to the upper layer.
This results in mismatch between transition disable policy
between the upper layer and the driver. This patch addresses this
issue by updating transition disable policy as part of port
authorization indication.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unused has_mrr (has multi-rate retry capabilities) member
from struct minstrel_priv (only set once in minstrel_ht_alloc, never
used again).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This should of course be CONFIG_, not CPTCFG_, which is an
artifact from working with backports.
Fixes: 9dd1953846 ("wifi: nl80211/mac80211: clarify link ID in control port TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HE added support for dynamic fragmentation inside aggregation
sessions, but no existing driver ever advertises it. Thus,
remove the code for now, it cannot work as-is in MLO. For it
to properly work in MLO, we'd need to validate that the frag
level is identical across all the link bands/iftypes, which
is a good amount of complex code that's just not worth it as
long as no driver has support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the deflink of the station is on 6 GHz, then it won't have HT.
If at the same time we're using MLO, then vif.bss_conf isn't used,
and thus vif.bss_conf.chandef.chan is NULL, causing the code to
crash.
Fix this by just checking for both HT and HE, and refusing the
aggregation session if both are not present. This might be a bit
wrong since it would accept an aggregation session from a peer
that has HE but no HT on 2.4 or 5 GHz, but such a peer shouldn't
exist in the first place, and it probably supports aggregation if
it has HE support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This won't work right at least with the code as it is, so
at least for now just assume it's never set for MLO. It may
very well never change, almost no drivers support it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the code that sets the DTIM period to always propagate it
into link->conf->dtim_period and not overwrite it, while still
preferring to set it from the beacon data if available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the station has no HT, we deny the aggregation session
but the error message talks about QoS; change it to say HT
instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ensure that the link ID matches in auth/assoc continuation,
otherwise we need to reset all the data.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If association to an AP without a link 0 fails, then we crash in
tracing because it assumes that either ap_mld_addr or link 0 BSS
is valid, since we clear sdata->vif.valid_links and then don't
add the ap_mld_addr to the struct.
Since we clear also sdata->vif.cfg.ap_addr, keep a local copy of
it and assign it earlier, before clearing valid_links, to fix
this.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The subelements obviously start after the common data, including
the common multi-link element structure definition itself. This
bug was possibly just hidden by the higher bits of the control
being set to 0, so the iteration just found one bogus element
and most of the code could continue anyway.
Fixes: 0f48b8b88a ("wifi: ieee80211: add definitions for multi-link element")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We might sometimes need to use RCU and locking in the same code
path, so add the two variants link_conf_dereference_check() and
link_sta_dereference_check().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since this frame is addressed from/to an MLD, it should be
built with the correct AP MLD address (in station mode) to
be encrypted properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If any driver relies entirely on the scan request BSSID,
then that would be wrong for internal scans. Initialize
it to the broadcast address since we don't otherwise use
the field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, we rely only on the AP capability. If the AP supports
TWT responder we will advertise TWT requester even if the driver
or HW doesn't support it. Fix this by checking the HW capability.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should set the parameters here per link, except
unfortunately ap_isolate, but we can't really change
that anymore so it'll remain a quirk in the API in
that you need to change it on one of the valid links
and it'll apply to all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This management frame is intended for the MLD so we
treat it in mac80211 as MLD addressed as well, and
should therefore use the MLD address of the AP for
the BSSID field in the frame, address translation
applies.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We use this to look up the destination station, so it
needs to be the MLD address of the AP for an MLO; use
ap_addr instead of the BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the AP returned a non success status for one of the links,
do not activate the link.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
