[ Upstream commit ff48b37802 ]
scsi_rescan_device() takes a scsi device lock before executing a device
handler and device driver rescan methods. Waiting for the completion of
any command issued to the device by these methods will thus be done with
the device lock held. As a result, there is a risk of deadlocking within
the power management code if scsi_rescan_device() is called to handle a
device resume with the associated scsi device not yet resumed.
Avoid such situation by checking that the target scsi device is in the
running state, that is, fully capable of executing commands, before
proceeding with the rescan and bailout returning -EWOULDBLOCK otherwise.
With this error return, the caller can retry rescaning the device after
a delay.
The state check is done with the device lock held and is thus safe
against incoming suspend power management operations.
Fixes: 6aa0365a3c ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Stable-dep-of: 8b4d9469d0 ("ata: libata-scsi: Fix delayed scsi_rescan_device() execution")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99398d2070 ]
If an error occurs when resuming a host adapter before the devices
attached to the adapter are resumed, the adapter low level driver may
remove the scsi host, resulting in a call to sd_remove() for the
disks of the host. This in turn results in a call to sd_shutdown() which
will issue a synchronize cache command and a start stop unit command to
spindown the disk. sd_shutdown() issues the commands only if the device
is not already runtime suspended but does not check the power state for
system-wide suspend/resume. That is, the commands may be issued with the
device in a suspended state, which causes PM resume to hang, forcing a
reset of the machine to recover.
Fix this by tracking the suspended state of a disk by introducing the
suspended boolean field in the scsi_disk structure. This flag is set to
true when the disk is suspended is sd_suspend_common() and resumed with
sd_resume(). When suspended is true, sd_shutdown() is not executed from
sd_remove().
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cc2ffe5c1 ]
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 99398d2070 ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a85890559 ]
During system resume, ata_port_pm_resume() triggers ata EH to
1) Resume the controller
2) Reset and rescan the ports
3) Revalidate devices
This EH execution is started asynchronously from ata_port_pm_resume(),
which means that when sd_resume() is executed, none or only part of the
above processing may have been executed. However, sd_resume() issues a
START STOP UNIT to wake up the drive from sleep mode. This command is
translated to ATA with ata_scsi_start_stop_xlat() and issued to the
device. However, depending on the state of execution of the EH process
and revalidation triggerred by ata_port_pm_resume(), two things may
happen:
1) The START STOP UNIT fails if it is received before the controller has
been reenabled at the beginning of the EH execution. This is visible
with error messages like:
ata10.00: device reported invalid CHS sector 0
sd 9:0:0:0: [sdc] Start/Stop Unit failed: Result: hostbyte=DID_OK driverbyte=DRIVER_OK
sd 9:0:0:0: [sdc] Sense Key : Illegal Request [current]
sd 9:0:0:0: [sdc] Add. Sense: Unaligned write command
sd 9:0:0:0: PM: dpm_run_callback(): scsi_bus_resume+0x0/0x90 returns -5
sd 9:0:0:0: PM: failed to resume async: error -5
2) The START STOP UNIT command is received while the EH process is
on-going, which mean that it is stopped and must wait for its
completion, at which point the command is rather useless as the drive
is already fully spun up already. This case results also in a
significant delay in sd_resume() which is observable by users as
the entire system resume completion is delayed.
Given that ATA devices will be woken up by libata activity on resume,
sd_resume() has no need to issue a START STOP UNIT command, which solves
the above mentioned problems. Do not issue this command by introducing
the new scsi_device flag no_start_on_resume and setting this flag to 1
in ata_scsi_dev_config(). sd_resume() is modified to issue a START STOP
UNIT command only if this flag is not set.
Reported-by: Paul Ausbeck <paula@soe.ucsc.edu>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215880
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Tanner Watkins <dalzot@gmail.com>
Tested-by: Paul Ausbeck <paula@soe.ucsc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Stable-dep-of: 99398d2070 ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f1a98813b ]
On incoming TCP reset, subflow closing could happen before error
propagation. That in turn could cause the socket error being ignored,
and a missing socket state transition, as reported by Daire-Byrne.
Address the issues explicitly checking for subflow socket error at
close time. To avoid code duplication, factor-out of __mptcp_error_report()
a new helper implementing the relevant bits.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/429
Fixes: 15cc104533 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ae8e5ad99 ]
mptcp_poll() reads sk->sk_err without socket lock held/owned.
Add READ_ONCE() and WRITE_ONCE() to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5fbeff1ab ("mptcp: move __mptcp_error_report in protocol.c")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27e5ccc2d5 ]
According to RFC 8684 section 3.3:
A connection is not closed unless [...] or an implementation-specific
connection-level send timeout.
Currently the MPTCP protocol does not implement such timeout, and
connection timing-out at the TCP-level never move to close state.
Introduces a catch-up condition at subflow close time to move the
MPTCP socket to close, too.
That additionally allows removing similar existing inside the worker.
Finally, allow some additional timeout for plain ESTABLISHED mptcp
sockets, as the protocol allows creating new subflows even at that
point and making the connection functional again.
This issue is actually present since the beginning, but it is basically
impossible to solve without a long chain of functional pre-requisites
topped by commit bbd49d114d ("mptcp: consolidate transition to
TCP_CLOSE in mptcp_do_fastclose()"). When backporting this current
patch, please also backport this other commit as well.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/430
Fixes: e16163b6e2 ("mptcp: refactor shutdown and close")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6909dc1c1 ]
The msk socket uses to different timeout to track close related
events and retransmissions. The existing helpers do not indicate
clearly which timer they actually touch, making the related code
quite confusing.
Change the existing helpers name to avoid such confusion. No
functional change intended.
This patch is linked to the next one ("mptcp: fix dangling connection
hang-up"). The two patches are supposed to be backported together.
Cc: stable@vger.kernel.org # v5.11+
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 27e5ccc2d5 ("mptcp: fix dangling connection hang-up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e765886249 ]
Tegra audio graph card has many DAI links which connects internal
AHUB modules and external audio codecs. Since these are DPCM links,
hw_params() call in the machine driver happens for each connected
BE link and PLLA is updated every time. This is not really needed
for all links as only I/O link DAIs derive respective clocks from
PLLA_OUT0 and thus from PLLA. Hence add checks to limit the clock
updates to DAIs over I/O links.
This found to be fixing a DMIC clock discrepancy which is suspected
to happen because of back to back quick PLLA and PLLA_OUT0 rate
updates. This was observed on Jetson TX2 platform where DMIC clock
ended up with unexpected value.
Fixes: 202e2f7745 ("ASoC: tegra: Add audio graph based card driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1694098945-32760-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4597648fdd upstream.
This reverts commits 86327e8eb9 ("memcg: drop kmem.limit_in_bytes") and
partially reverts 58056f7750 ("memcg, kmem: further deprecate
kmem.limit_in_bytes") which have incrementally removed support for the
kernel memory accounting hard limit. Unfortunately it has turned out that
there is still userspace depending on the existence of
memory.kmem.limit_in_bytes [1]. The underlying functionality is not
really required but the non-existent file just confuses the userspace
which fails in the result. The patch to fix this on the userspace side
has been submitted but it is hard to predict how it will propagate through
the maze of 3rd party consumers of the software.
Now, reverting alone 86327e8eb9 is not an option because there is
another set of userspace which cannot cope with ENOTSUPP returned when
writing to the file. Therefore we have to go and revisit 58056f7750 as
well. There are two ways to go ahead. Either we give up on the
deprecation and fully revert 58056f7750 as well or we can keep
kmem.limit_in_bytes but make the write a noop and warn about the fact.
This should work for both known breaking workloads which depend on the
existence but do not depend on the hard limit enforcement.
Note to backporters to stable trees. a8c49af3be ("memcg: add per-memcg
total kernel memory stat") introduced in 4.18 has added memcg_account_kmem
so the accounting is not done by obj_cgroup_charge_pages directly for v1
anymore. Prior kernels need to add it explicitly (thanks to Johannes for
pointing this out).
[akpm@linux-foundation.org: fix build - remove unused local]
Link: http://lkml.kernel.org/r/20230920081101.GA12096@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net [1]
Link: https://lkml.kernel.org/r/ZRE5VJozPZt9bRPy@dhcp22.suse.cz
Fixes: 86327e8eb9 ("memcg: drop kmem.limit_in_bytes")
Fixes: 58056f7750 ("memcg, kmem: further deprecate kmem.limit_in_bytes")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Tejun heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86327e8eb9 upstream.
kmem.limit_in_bytes (v1 way to limit kernel memory usage) has been
deprecated since 58056f7750 ("memcg, kmem: further deprecate
kmem.limit_in_bytes") merged in 5.16. We haven't heard about any serious
users since then but it seems that the mere presence of the file is
causing more harm thatn good. We (SUSE) have had several bug reports from
customers where Docker based containers started to fail because a write to
kmem.limit_in_bytes has failed.
This was unexpected because runc code only expects ENOENT (kmem disabled)
or EBUSY (tasks already running within cgroup). So a new error code was
unexpected and the whole container startup failed. This has been later
addressed by
52390d6804
so current Docker runtimes do not suffer from the problem anymore. There
are still older version of Docker in use and likely hard to get rid of
completely.
Address this by wiping out the file completely and effectively get back to
pre 4.5 era and CONFIG_MEMCG_KMEM=n configuration.
I would recommend backporting to stable trees which have picked up
58056f7750 ("memcg, kmem: further deprecate kmem.limit_in_bytes").
[mhocko@suse.com: restore _KMEM switch case]
Link: https://lkml.kernel.org/r/ZKe5wxdbvPi5Cwd7@dhcp22.suse.cz
Link: https://lkml.kernel.org/r/20230704115240.14672-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c31515857 upstream.
The elf-fdpic loader hard sets the process personality to either
PER_LINUX_FDPIC for true elf-fdpic binaries or to PER_LINUX for normal ELF
binaries (in this case they would be constant displacement compiled with
-pie for example). The problem with that is that it will lose any other
bits that may be in the ELF header personality (such as the "bug
emulation" bits).
On the ARM architecture the ADDR_LIMIT_32BIT flag is used to signify a
normal 32bit binary - as opposed to a legacy 26bit address binary. This
matters since start_thread() will set the ARM CPSR register as required
based on this flag. If the elf-fdpic loader loses this bit the process
will be mis-configured and crash out pretty quickly.
Modify elf-fdpic loader personality setting so that it preserves the upper
three bytes by using the SET_PERSONALITY macro to set it. This macro in
the generic case sets PER_LINUX and preserves the upper bytes.
Architectures can override this for their specific use case, and ARM does
exactly this.
The problem shows up quite easily running under qemu using the ARM
architecture, but not necessarily on all types of real ARM hardware. If
the underlying ARM processor does not support the legacy 26-bit addressing
mode then everything will work as expected.
Link: https://lkml.kernel.org/r/20230907011808.2985083-1-gerg@kernel.org
Fixes: 1bde925d23 ("fs/binfmt_elf_fdpic.c: provide NOMMU loader for regular ELF binaries")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Ungerer <gerg@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc77721ea4 upstream.
I had the following weird phenomena on a mobile phone: while
the capacity in /sys/class/power_supply/ab8500_fg/capacity
would reflect the actual charge and capacity of the battery,
only 1/3 of the value was shown on the battery status
indicator and warnings for low battery appeared.
It turns out that UPower, the Freedesktop power daemon,
will average all the power supplies of type "battery" in
/sys/class/power_supply/* if there is more than one battery.
For the AB8500, there was "battery" ab8500_fg, ab8500_btemp
and ab8500_chargalg. The latter two don't know anything
about the battery, and should not be considered. They were
however averaged and with the capacity of 0.
Flag ab8500_btemp and ab8500_chargalg with type "unknown"
so they are not averaged as batteries.
Remove the technology prop from ab8500_btemp as well, all
it does is snoop in on knowledge from another supply.
After this the battery indicator shows the right value.
Cc: Stefan Hansson <newbyte@disroot.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 753a4d531b upstream.
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
- Seagate IronWolf ST12000VN0008
- Seagate IronWolf ST8000NE0004
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d5 ("libata: change drive ready wait after hard reset to 5s")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75e2bd5f1e upstream.
libsas does its own domain based power management of ports. For such
ports, libata should not use a device type defining power management
operations as executing these operations for suspend/resume in addition
to libsas calls to ata_sas_port_suspend() and ata_sas_port_resume() is
not necessary (and likely dangerous to do, even though problems are not
seen currently).
Introduce the new ata_port_sas_type device_type for ports managed by
libsas. This new device type is used in ata_tport_add() and is defined
without power management operations.
Fixes: 2fcbdcb4c8 ("[SCSI] libata: export ata_port suspend/resume infrastructure for sas")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84d76529c6 upstream.
Whenever an ATA adapter driver is removed (e.g. rmmod),
ata_port_detach() is called repeatedly for all the adapter ports to
remove (unload) the devices attached to the port and delete the port
device itself. Removing of devices is done using libata EH with the
ATA_PFLAG_UNLOADING port flag set. This causes libata EH to execute
ata_eh_unload() which disables all devices attached to the port.
ata_port_detach() finishes by calling scsi_remove_host() to remove the
scsi host associated with the port. This function will trigger the
removal of all scsi devices attached to the host and in the case of
disks, calls to sd_shutdown() which will flush the device write cache
and stop the device. However, given that the devices were already
disabled by ata_eh_unload(), the synchronize write cache command and
start stop unit commands fail. E.g. running "rmmod ahci" with first
removing sd_mod results in error messages like:
ata13.00: disable device
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] Stopping disk
sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
Fix this by removing all scsi devices of the ata devices connected to
the port before scheduling libata EH to disable the ATA devices.
Fixes: 720ba12620 ("[PATCH] libata-hp: update unload-unplug")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b8e0af4a7 upstream.
The function ata_port_request_pm() checks the port flag
ATA_PFLAG_PM_PENDING and calls ata_port_wait_eh() if this flag is set to
ensure that power management operations for a port are not scheduled
simultaneously. However, this flag check is done without holding the
port lock.
Fix this by taking the port lock on entry to the function and checking
the flag under this lock. The lock is released and re-taken if
ata_port_wait_eh() needs to be called. The two WARN_ON() macros checking
that the ATA_PFLAG_PM_PENDING flag was cleared are removed as the first
call is racy and the second one done without holding the port lock.
Fixes: 5ef4108291 ("ata: add ata port system PM callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0b65f9b81 upstream.
Alex reported that running ssh over IPv6 does not work with
Thunderbolt/USB4 networking driver. The reason for that is that driver
should call skb_is_gso() before calling skb_is_gso_v6(), and it should
not return false after calculates the checksum successfully. This probably
was a copy paste error from the original driver where it was done properly.
Reported-by: Alex Balcanquall <alex@alexbal.com>
Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58bfe2ccec upstream.
A user reported some issues with smaller file systems that get very
full. While investigating this issue I noticed that df wasn't showing
100% full, despite having 0 chunk space and having < 1MiB of available
metadata space.
This turns out to be an overflow issue, we're doing:
total_available_metadata_space - SZ_4M < global_block_rsv_size
to determine if there's not enough space to make metadata allocations,
which overflows if total_available_metadata_space is < 4M. Fix this by
checking to see if our available space is greater than the 4M threshold.
This makes df properly report 100% usage on the file system.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e0cb399c7 upstream.
It was discovered that the ring buffer polling was incorrectly stating
that read would not block, but that's because polling did not take into
account that reads will block if the "buffer-percent" was set. Instead,
the ring buffer polling would say reads would not block if there was any
data in the ring buffer. This was incorrect behavior from a user space
point of view. This was fixed by commit 42fb0a1e84 by having the polling
code check if the ring buffer had more data than what the user specified
"buffer percent" had.
The problem now is that the polling code did not register itself to the
writer that it wanted to wait for a specific "full" value of the ring
buffer. The result was that the writer would wake the polling waiter
whenever there was a new event. The polling waiter would then wake up, see
that there's not enough data in the ring buffer to notify user space and
then go back to sleep. The next event would wake it up again.
Before the polling fix was added, the code would wake up around 100 times
for a hackbench 30 benchmark. After the "fix", due to the constant waking
of the writer, it would wake up over 11,0000 times! It would never leave
the kernel, so the user space behavior was still "correct", but this
definitely is not the desired effect.
To fix this, have the polling code add what it's waiting for to the
"shortest_full" variable, to tell the writer not to wake it up if the
buffer is not as full as it expects to be.
Note, after this fix, it appears that the waiter is now woken up around 2x
the times it was before (~200). This is a tremendous improvement from the
11,000 times, but I will need to spend some time to see why polling is
more aggressive in its wakeups than the read blocking code.
Link: https://lore.kernel.org/linux-trace-kernel/20230929180113.01c2cae3@rorschach.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Fixes: 42fb0a1e84 ("tracing/ring-buffer: Have polling block on watermark")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Tested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46a9ea6681 upstream.
After the commit in Fixes:, if a module that created a slab cache does not
release all of its allocated objects before destroying the cache (at rmmod
time), we might end up releasing the kmem_cache object without removing it
from the slab_caches list thus corrupting the list as kmem_cache_destroy()
ignores the return value from shutdown_cache(), which in turn never removes
the kmem_cache object from slabs_list in case __kmem_cache_shutdown() fails
to release all of the cache's slabs.
This is easily observable on a kernel built with CONFIG_DEBUG_LIST=y
as after that ill release the system will immediately trip on list_add,
or list_del, assertions similar to the one shown below as soon as another
kmem_cache gets created, or destroyed:
[ 1041.213632] list_del corruption. next->prev should be ffff89f596fb5768, but was 52f1e5016aeee75d. (next=ffff89f595a1b268)
[ 1041.219165] ------------[ cut here ]------------
[ 1041.221517] kernel BUG at lib/list_debug.c:62!
[ 1041.223452] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[ 1041.225408] CPU: 2 PID: 1852 Comm: rmmod Kdump: loaded Tainted: G B W OE 6.5.0 #15
[ 1041.228244] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20230524-3.fc37 05/24/2023
[ 1041.231212] RIP: 0010:__list_del_entry_valid+0xae/0xb0
Another quick way to trigger this issue, in a kernel with CONFIG_SLUB=y,
is to set slub_debug to poison the released objects and then just run
cat /proc/slabinfo after removing the module that leaks slab objects,
in which case the kernel will panic:
[ 50.954843] general protection fault, probably for non-canonical address 0xa56b6b6b6b6b6b8b: 0000 [#1] PREEMPT SMP PTI
[ 50.961545] CPU: 2 PID: 1495 Comm: cat Kdump: loaded Tainted: G B W OE 6.5.0 #15
[ 50.966808] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20230524-3.fc37 05/24/2023
[ 50.972663] RIP: 0010:get_slabinfo+0x42/0xf0
This patch fixes this issue by properly checking shutdown_cache()'s
return value before taking the kmem_cache_release() branch.
Fixes: 0495e337b7 ("mm/slab_common: Deleting kobject in kmem_cache_destroy() without holding slab_mutex/cpu_hotplug_lock")
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a6a464774 upstream.
Specific stress involving frequent CPU-hotplug operations, such as
running rcutorture for example, may trigger the following message:
NOHZ tick-stop error: local softirq work is pending, handler #02!!!"
This happens in the CPU-down hotplug process, after
CPUHP_AP_SMPBOOT_THREADS whose teardown callback parks ksoftirqd, and
before the target CPU shuts down through CPUHP_AP_IDLE_DEAD. In this
fragile intermediate state, softirqs waiting for threaded handling may be
forever ignored and eventually reported by the idle task as in the above
example.
However some vectors are known to be safe as long as the corresponding
subsystems have teardown callbacks handling the migration of their
events. The above error message reports pending timers softirq although
this vector can be considered as hotplug safe because the
CPUHP_TIMERS_PREPARE teardown callback performs the necessary migration
of timers after the death of the CPU. Hrtimers also have a similar
hotplug handling.
Therefore this error message, as far as (hr-)timers are concerned, can
be considered spurious and the relevant softirq vectors can be marked as
hotplug safe.
Fixes: 0345691b24 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230912104406.312185-6-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08713cb006 upstream.
Jakub Kicinski says:
We've got some new kdoc warnings here:
net/netfilter/nft_set_pipapo.c:1557: warning: Function parameter or member '_set' not described in 'pipapo_gc'
net/netfilter/nft_set_pipapo.c:1557: warning: Excess function parameter 'set' description in 'pipapo_gc'
include/net/netfilter/nf_tables.h:577: warning: Function parameter or member 'dead' not described in 'nft_set'
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Fixes: f6c383b8c3 ("netfilter: nf_tables: adapt set backend to use GC transaction API")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20230810104638.746e46f1@kernel.org/
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc09027786 upstream.
During RCU-boost testing with the TREE03 rcutorture config, I found that
after a few hours, the machine locks up.
On tracing, I found that there is a live lock happening between 2 CPUs.
One CPU has an RT task running, while another CPU is being offlined
which also has an RT task running. During this offlining, all threads
are migrated. The migration thread is repeatedly scheduled to migrate
actively running tasks on the CPU being offlined. This results in a live
lock because select_fallback_rq() keeps picking the CPU that an RT task
is already running on only to get pushed back to the CPU being offlined.
It is anyway pointless to pick CPUs for pushing tasks to if they are
being offlined only to get migrated away to somewhere else. This could
also add unwanted latency to this task.
Fix these issues by not selecting CPUs in RT if they are not 'active'
for scheduling, using the cpu_active_mask. Other parts in core.c already
use cpu_active_mask to prevent tasks from being put on CPUs going
offline.
With this fix I ran the tests for days and could not reproduce the
hang. Without the patch, I hit it in a few hours.
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230923011409.3522762-1-joel@joelfernandes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cff9b2332a upstream.
Initial booting is setting the task flag to idle (PF_IDLE) by the call
path sched_init() -> init_idle(). Having the task idle and calling
call_rcu() in kernel/rcu/tiny.c means that TIF_NEED_RESCHED will be
set. Subsequent calls to any cond_resched() will enable IRQs,
potentially earlier than the IRQ setup has completed. Recent changes
have caused just this scenario and IRQs have been enabled early.
This causes a warning later in start_kernel() as interrupts are enabled
before they are fully set up.
Fix this issue by setting the PF_IDLE flag later in the boot sequence.
Although the boot task was marked as idle since (at least) d80e4fda576d,
I am not sure that it is wrong to do so. The forced context-switch on
idle task was introduced in the tiny_rcu update, so I'm going to claim
this fixes 5f6130fa52.
Fixes: 5f6130fa52 ("tiny_rcu: Directly force QS when call_rcu_[bh|sched]() on idle_task")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mm/CAMuHMdWpvpWoDa=Ox-do92czYRvkok6_x6pYUH+ZouMcJbXy+Q@mail.gmail.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ef6009235 upstream.
For REPORT SUPPORTED OPERATION CODES command, the service action field is
defined as bits 0-4 in the second byte in the CDB. Bits 5-7 in the second
byte are reserved.
Only look at the service action field in the second byte when determining
if the MAINTENANCE IN opcode is a REPORT SUPPORTED OPERATION CODES command.
This matches how we only look at the service action field in the second
byte when determining if the SERVICE ACTION IN(16) opcode is a READ
CAPACITY(16) command (reserved bits 5-7 in the second byte are ignored).
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb99ef1786 upstream.
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
