commit 221c3a09dd upstream.
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb1 ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba8da03fa7 upstream.
Crypto engine (CAAM) on LS1012A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 85b85c5695 ("arm64: dts: ls1012a: add crypto node")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d1e25a8c upstream.
The .callback of the quirk for Sony VPCEH3U1E was unintetionally
removed by the commit 25417185e9 ("ACPI: video: Add DMI quirk
for GIGABYTE GB-BXBT-2807"). Add it back to make sure the quirk
for Sony VPCEH3U1E works as expected.
Fixes: 25417185e9 ("ACPI: video: Add DMI quirk for GIGABYTE GB-BXBT-2807")
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Cc: 5.11+ <stable@vger.kernel.org> # 5.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf10bd4c4a upstream.
To allow performing tag checks on page_alloc addresses obtained via
page_address(), tag-based KASAN modes store tags for page_alloc
allocations in page->flags.
Currently, the default tag value stored in page->flags is 0x00.
Therefore, page_address() returns a 0x00ffff... address for pages that
were not allocated via page_alloc.
This might cause problems. A particular case we encountered is a
conflict with KFENCE. If a KFENCE-allocated slab object is being freed
via kfree(page_address(page) + offset), the address passed to kfree()
will get tagged with 0x00 (as slab pages keep the default per-page
tags). This leads to is_kfence_address() check failing, and a KFENCE
object ending up in normal slab freelist, which causes memory
corruptions.
This patch changes the way KASAN stores tag in page-flags: they are now
stored xor'ed with 0xff. This way, KASAN doesn't need to initialize
per-page flags for every created page, which might be slow.
With this change, page_address() returns natively-tagged (with 0xff)
pointers for pages that didn't have tags set explicitly.
This patch fixes the encountered conflict with KFENCE and prevents more
similar issues that can occur in the future.
Link: https://lkml.kernel.org/r/1a41abb11c51b264511d9e71c303bb16d5cb367b.1615475452.git.andreyknvl@google.com
Fixes: 2813b9c029 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 538d2dd0b9 upstream.
Stop reporting SW_DOCK events because this breaks suspend-on-lid-close.
SW_DOCK should only be reported for docking stations, but all the DSDTs in
my DSDT collection which use the intel-vbtn code, always seem to use this
for 2-in-1s / convertibles and set SW_DOCK=1 when in laptop-mode (in tandem
with setting SW_TABLET_MODE=0).
This causes userspace to think the laptop is docked to a port-replicator
and to disable suspend-on-lid-close, which is undesirable.
Map the dock events to KEY_IGNORE to avoid this broken SW_DOCK reporting.
Note this may theoretically cause us to stop reporting SW_DOCK on some
device where the 0xCA and 0xCB intel-vbtn events are actually used for
reporting docking to a classic docking-station / port-replicator but
I'm not aware of any such devices.
Also the most important thing is that we only report SW_DOCK when it
reliably reports being docked to a classic docking-station without any
false positives, which clearly is not the case here. If there is a
chance of reporting false positives then it is better to not report
SW_DOCK at all.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210321163513.72328-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 804741ac7b upstream.
Since commit 8e850f25b5 ("net: socionext: Stop PHY before resetting
netsec") netsec_netdev_init() power downs phy before resetting the
controller. However, the state is not restored once the reset is
complete. As a result it is not possible to bring up network on a
platform with Broadcom BCM5482 phy.
Fix the issue by restoring phy power state after controller reset is
complete.
Fixes: 8e850f25b5 ("net: socionext: Stop PHY before resetting netsec")
Cc: stable@vger.kernel.org
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ceb1ace4a ]
In https://bugs.gentoo.org/769614 Dmitry noticed that
`ptrace(PTRACE_GET_SYSCALL_INFO)` does not work for syscalls called via
glibc's syscall() wrapper.
ia64 has two ways to call syscalls from userspace: via `break` and via
`eps` instructions.
The difference is in stack layout:
1. `eps` creates simple stack frame: no locals, in{0..7} == out{0..8}
2. `break` uses userspace stack frame: may be locals (glibc provides
one), in{0..7} == out{0..8}.
Both work fine in syscall handling cde itself.
But `ptrace(PTRACE_GET_SYSCALL_INFO)` uses unwind mechanism to
re-extract syscall arguments but it does not account for locals.
The change always skips locals registers. It should not change `eps`
path as kernel's handler already enforces locals=0 and fixes `break`.
Tested on v5.10 on rx3600 machine (ia64 9040 CPU).
Link: https://lkml.kernel.org/r/20210221002554.333076-1-slyfox@gentoo.org
Link: https://bugs.gentoo.org/769614
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ec491447b ]
register_disk() suppress uevents for devices with the GENHD_FL_HIDDEN
but enables uevents at the end again in order to announce disk after
possible partitions are created.
When the device is removed the uevents are still on and user land sees
'remove' messages for devices which were never 'add'ed to the system.
KERNEL[95481.571887] remove /devices/virtual/nvme-fabrics/ctl/nvme5/nvme0c5n1 (block)
Let's suppress the uevents for GENHD_FL_HIDDEN by not enabling the
uevents at all.
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Link: https://lore.kernel.org/r/20210311151917.136091-1-dwagner@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f8be1f53b ]
The NFSv4 protocol doesn't have any notion of reomoving an attribute, so
removexattr(path,"system.nfs4_acl") doesn't make sense.
There's no documented return value. Arguably it could be EOPNOTSUPP but
I'm a little worried an application might take that to mean that we
don't support ACLs or xattrs. How about EINVAL?
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae3afe6308 ]
When a command has been aborted we should return NVME_SC_HOST_ABORTED_CMD
to be consistent with the other transports.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d358938198 ]
NVME_REQ_CANCELLED is translated into -EINTR in nvme_submit_sync_cmd(),
so we should be setting this flags during nvme_cancel_request() to
ensure that the callers to nvme_submit_sync_cmd() will get the correct
error code when the controller is reset.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5b0e0677b ]
Jakub reported that:
static struct net_device *rtl8139_init_board(struct pci_dev *pdev)
{
...
u64_stats_init(&tp->rx_stats.syncp);
u64_stats_init(&tp->tx_stats.syncp);
...
}
results in lockdep getting confused between the RX and TX stats lock.
This is because u64_stats_init() is an inline calling seqcount_init(),
which is a macro using a static variable to generate a lockdep class.
By wrapping that in an inline, we negate the effect of the macro and
fold the static key variable, hence the confusion.
Fix by also making u64_stats_init() a macro for the case where it
matters, leaving the other case an inline for argument validation
etc.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Debugged-by: "Ahmed S. Darwish" <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: "Erhard F." <erhard_f@mailbox.org>
Link: https://lkml.kernel.org/r/YEXicy6+9MksdLZh@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27ac5aada0 ]
The refcount of the "hl_fpriv" structure is not used for the control
device, and thus hl_hpriv_put() is not called when releasing this
device.
This results with no call to put_pid(), so add it explicitly in
hl_device_release_ctrl().
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5e8b80d35 ]
is_no_fault_exception() has two bugs which were discovered via random
opcode testing with stress-ng. Both are caused by improper filtering
of opcodes.
The first bug can be triggered by a floating point store with a no-fault
ASI, for instance "sta %f0, [%g0] #ASI_PNF", opcode C1A01040.
The code first tests op3[5] (0x1000000), which denotes a floating
point instruction, and then tests op3[2] (0x200000), which denotes a
store instruction. But these bits are not mutually exclusive, and the
above mentioned opcode has both bits set. The intent is to filter out
stores, so the test for stores must be done first in order to have
any effect.
The second bug can be triggered by a floating point load with one of
the invalid ASI values 0x8e or 0x8f, which pass this check in
is_no_fault_exception():
if ((asi & 0xf2) == ASI_PNF)
An example instruction is "ldqa [%l7 + %o7] #ASI 0x8f, %f38",
opcode CF95D1EF. Asi values greater than 0x8b (ASI_SNFL) are fatal
in handle_ldf_stq(), and is_no_fault_exception() must not allow these
invalid asi values to make it that far.
In both of these cases, handle_ldf_stq() reacts by calling
sun4v_data_access_exception() or spitfire_data_access_exception(),
which call is_no_fault_exception() and results in an infinite
recursion.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3d100eae4 ]
A customer has reported that their dmesg were being flooded by
CIFS: VFS: \\server Cancelling wait for mid xxx cmd: a
CIFS: VFS: \\server Cancelling wait for mid yyy cmd: b
CIFS: VFS: \\server Cancelling wait for mid zzz cmd: c
because some processes that were performing statfs(2) on the share had
been interrupted due to their automount setup when certain users
logged in and out.
Change it to FYI as they should be mostly informative rather than
error messages.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4416e98594 ]
this one is similar to the phy_data allocation fix in uPD98402, the
driver allocate the idt77105_priv and store to dev_data but later
dereference using dev->dev_data, which will cause null-ptr-dereference.
fix this issue by changing dev_data to phy_data so that PRIV(dev) can
work correctly.
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3153724fc0 ]
dev->dev_data is set in zatm.c, calling zatm_start() will overwrite this
dev->dev_data in uPD98402_start() and a subsequent PRIV(dev)->lock
(i.e dev->phy_data->lock) will result in a null-ptr-dereference.
I believe this is a typo and what it actually want to do is to allocate
phy_data instead of dev_data.
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e26962236 ]
The second IRQ line really is optional, so use
platform_get_irq_optional() to obtain it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62765d3955 ]
When priv->rx_skbuff or priv->tx_skbuff is NULL, no error return code of
uhdlc_init() is assigned.
To fix this bug, ret is assigned with -ENOMEM in these cases.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 143c253f42 ]
When hns_assemble_skb() returns NULL to skb, no error return code of
hns_nic_clear_all_rx_fetch() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad3dbe35c8 ]
CREATE requests return a post_op_fh3, rather than nfs_fh3. The
post_op_fh3 includes an extra word to indicate 'handle_follows'.
Without that additional word, create fails when full 64-byte
filehandles are in use.
Add NFS3_post_op_fh_sz, and correct the size calculation for
NFS3_createres_sz.
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb31cb805 ]
Add "arm,vexpress" to cpufreq-dt-platdev blacklist since the actual
scaling is handled by the firmware cpufreq drivers(scpi, scmi and
vexpress-spc).
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88fd98a230 ]
When doing a large read or write workload we only
very gradually increase the number of credits
which can cause problems with parallelizing large i/o
(I/O ramps up more slowly than it should for large
read/write workloads) especially with multichannel
when the number of credits on the secondary channels
starts out low (e.g. less than about 130) or when
recovering after server throttled back the number
of credit.
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8861bab48 ]
When using jumbo packets and overrunning rx queue with napi enabled,
the following sequence is observed in gfar_add_rx_frag:
| lstatus | | skb |
t | lstatus, size, flags | first | len, data_len, *ptr |
---+--------------------------------------+-------+-----------------------+
13 | 18002348, 9032, INTERRUPT LAST | 0 | 9600, 8000, f554c12e |
12 | 10000640, 1600, INTERRUPT | 0 | 8000, 6400, f554c12e |
11 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, f554c12e |
10 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, f554c12e |
09 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, f554c12e |
08 | 14000640, 1600, INTERRUPT FIRST | 0 | 1600, 0, f554c12e |
07 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, f554c12e |
06 | 1c000080, 128, INTERRUPT LAST FIRST | 1 | 0, 0, abf3bd6e |
05 | 18002348, 9032, INTERRUPT LAST | 0 | 8000, 6400, c5a57780 |
04 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, c5a57780 |
03 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, c5a57780 |
02 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, c5a57780 |
01 | 10000640, 1600, INTERRUPT | 0 | 1600, 0, c5a57780 |
00 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, c5a57780 |
So at t=7 a new packets is started but not finished, probably due to rx
overrun - but rx overrun is not indicated in the flags. Instead a new
packets starts at t=8. This results in skb->len to exceed size for the LAST
fragment at t=13 and thus a negative fragment size added to the skb.
This then crashes:
kernel BUG at include/linux/skbuff.h:2277!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c04689f4] skb_pull+0x2c/0x48
LR [c03f62ac] gfar_clean_rx_ring+0x2e4/0x844
Call Trace:
[ec4bfd38] [c06a84c4] _raw_spin_unlock_irqrestore+0x60/0x7c (unreliable)
[ec4bfda8] [c03f6a44] gfar_poll_rx_sq+0x48/0xe4
[ec4bfdc8] [c048d504] __napi_poll+0x54/0x26c
[ec4bfdf8] [c048d908] net_rx_action+0x138/0x2c0
[ec4bfe68] [c06a8f34] __do_softirq+0x3a4/0x4fc
[ec4bfed8] [c0040150] run_ksoftirqd+0x58/0x70
[ec4bfee8] [c0066ecc] smpboot_thread_fn+0x184/0x1cc
[ec4bff08] [c0062718] kthread+0x140/0x144
[ec4bff38] [c0012350] ret_from_kernel_thread+0x14/0x1c
This patch fixes this by checking for computed LAST fragment size, so a
negative sized fragment is never added.
In order to prevent the newer rx frame from getting corrupted, the FIRST
flag is checked to discard the incomplete older frame.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155b23e6e5 ]
RXMAC_BC_FRM_CNT_COUNT added to mp->rx_bcasts twice in a row
in niu_xmac_interrupt(). Remove the second addition.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6650d31f21 ]
When iavf_process_config() fails, no error return code of
iavf_init_get_resources() is assigned.
To fix this bug, err is assigned with the return value of
iavf_process_config(), and then err is checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38c26ff304 ]
When bdx_read_mac() fails, no error return code of bdx_probe()
is assigned.
To fix this bug, err is assigned with -EFAULT as error return code.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b5dc1a94d ]
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eead089311 ]
lkp reported a build error in fsp2.o:
CC arch/powerpc/platforms/44x/fsp2.o
{standard input}:577: Error: unsupported relocation against base
Which comes from:
pr_err("GESR0: 0x%08x\n", mfdcr(base + PLB4OPB_GESR0));
Where our mfdcr() macro is stringifying "base + PLB4OPB_GESR0", and
passing that to the assembler, which obviously doesn't work.
The mfdcr() macro already checks that the argument is constant using
__builtin_constant_p(), and if not calls the out-of-line version of
mfdcr(). But in this case GCC is smart enough to notice that "base +
PLB4OPB_GESR0" will be constant, even though it's not something we can
immediately stringify into a register number.
Segher pointed out that passing the register number to the inline asm
as a constant would be better, and in fact it fixes the build error,
presumably because it gives GCC a chance to resolve the value.
While we're at it, change mtdcr() similarly.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210218123058.748882-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4d7234ae ]
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
