commit 864d296cf9 upstream.
The function pci_enable_ari() may mistakenly set the downstream port
of a v1 PCIe switch in ARI Forwarding mode. This is a PCIe v2 feature,
and with an SR-IOV device on that switch port believing the switch above
is ARI capable it may attempt to use functions 8-255, translating into
invalid (non-zero) device numbers for that bus. This has been seen
to cause Completion Timeouts and general misbehaviour including hangs
and panics.
Acked-by: Don Dutile <ddutile@redhat.com>
Tested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 81d6743985 upstream.
<linux/kernel.h> is needed for min_t. The old version
happened to work on x86 because <asm/unaligned.h>
indirectly includes <linux/kernel.h>, but it didn't
work on ARM.
<linux/kernel.h> includes <asm/byteorder.h> so it's
not necessary to include it explicitly anymore.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 40ee4dffff upstream.
The "enable" file for the event system can be removed when a module
is unloaded and the event system only has events from that module.
As the event system nr_events count goes to zero, it may be freed
if its ref_count is also set to zero.
Like the "filter" file, the "enable" file may be opened by a task and
referenced later, after a module has been unloaded and the events for
that event system have been removed.
Although the "filter" file referenced the event system structure,
the "enable" file only references a pointer to the event system
name. Since the name is freed when the event system is removed,
it is possible that an access to the "enable" file may reference
a freed pointer.
Update the "enable" file to use the subsystem_open() routine that
the "filter" file uses, to keep a reference to the event system
structure while the "enable" file is opened.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e9dbfae53e upstream.
The event system is freed when its nr_events is set to zero. This happens
when a module created an event system and then later the module is
removed. Modules may share systems, so the system is allocated when
it is created and freed when the modules are unloaded and all the
events under the system are removed (nr_events set to zero).
The problem arises when a task opened the "filter" file for the
system. If the module is unloaded and it removed the last event for
that system, the system structure is freed. If the task that opened
the filter file accesses the "filter" file after the system has
been freed, the system will access an invalid pointer.
By adding a ref_count, and using it to keep track of what
is using the event system, we can free it after all users
are finished with the event system.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 63f21a56f1 upstream.
The existing code it pretty ugly. How about we clean it up even more
like this?
From: Anton Blanchard <anton@samba.org>
We check for timeout expiry in the outer loop, but we also need to
check it in the inner loop or we can lock up forever waiting for a
CPU to hit real mode.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 050438ed5a upstream.
In kexec jump support, jump back address passed to the kexeced
kernel via function calling ABI, that is, the function call
return address is the jump back entry.
Furthermore, jump back entry == 0 should be used to signal that
the jump back or preserve context is not enabled in the original
kernel.
But in the current implementation the stack position used for
function call return address is not cleared context
preservation is disabled. The patch fixes this bug.
Reported-and-tested-by: Yin Kangkai <kangkai.yin@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Link: http://lkml.kernel.org/r/1310607277-25029-1-git-send-email-ying.huang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c48a8fb0d3 upstream.
Copying hp_pins and speaker_pins from line_out_pins may confuse the
parser, and it can lead to duplicated initializations for the same pin
with a wrong DAC assignment. The problem appears in 3.0 kernel code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c81c6b356b upstream.
Commit dd203fa97b (ALSA: virtuoso: remove non-working controls on
Essence ST Deluxe) made it impossible to adjust the volume after the
driver initialized it to muted.
Ensure that those DACs that can be accessed with I2C are initialized
to the same volume that is the reset default of the DAC without I2C.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 5a96a899bb upstream.
DPEncoderService newer than 1.1 can't properly program the DP (display port)
link training. When facing such version use the DIGxEncoderControl method
instead. Fix DP link training on some R7XX.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fec62c368b upstream.
Most smartarrays tolerate it, but a few new ones don't.
Without this change some newer Smart Arrays will lock up
and i/o will grind to a halt.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b5b515445f upstream.
There's a code path in pmcraid that can be reached via device ioctl that
causes all sorts of ugliness, including heap corruption or triggering the
OOM killer due to consecutive allocation of large numbers of pages.
First, the user can call pmcraid_chr_ioctl(), with a type
PMCRAID_PASSTHROUGH_IOCTL. This calls through to
pmcraid_ioctl_passthrough(). Next, a pmcraid_passthrough_ioctl_buffer
is copied in, and the request_size variable is set to
buffer->ioarcb.data_transfer_length, which is an arbitrary 32-bit
signed value provided by the user. If a negative value is provided
here, bad things can happen. For example,
pmcraid_build_passthrough_ioadls() is called with this request_size,
which immediately calls pmcraid_alloc_sglist() with a negative size.
The resulting math on allocating a scatter list can result in an
overflow in the kzalloc() call (if num_elem is 0, the sglist will be
smaller than expected), or if num_elem is unexpectedly large the
subsequent loop will call alloc_pages() repeatedly, a high number of
pages will be allocated and the OOM killer might be invoked.
It looks like preventing this value from being negative in
pmcraid_ioctl_passthrough() would be sufficient.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit bfe159a512 upstream.
USB surprise removal of sr is triggering an oops in
scsi_dispatch_command(). What seems to be happening is that USB is
hanging on to a queue reference until the last close of the upper
device, so the crash is caused by surprise remove of a mounted CD
followed by attempted unmount.
The problem is that USB doesn't issue its final commands as part of
the SCSI teardown path, but on last close when the block queue is long
gone. The long term fix is probably to make sr do the teardown in the
same way as sd (so remove all the lower bits on ejection, but keep the
upper disk alive until last close of user space). However, the
current oops can be simply fixed by not allowing any commands to be
sent to a dead queue.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2a350cab9d upstream.
Noticed that when the sysfs interface of the SCSI SES
driver was used to request a fault indication the LED
flashed but the buzzer didn't sound. So it was doing
what REQUEST IDENT (locate) should do.
Changelog:
- fix the setting of REQUEST FAULT for the device slot
and array device slot elements in the enclosure control
diagnostic page
- note the potentially defective code that reads the
FAULT SENSED and FAULT REQUESTED bits from the enclosure
status diagnostic page
The attached patch is against git/scsi-misc-2.6
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 79b9677d88 upstream.
Some broken devices indicates that media has changed on every
GET_EVENT_STATUS_NOTIFICATION. This translates into MEDIA_CHANGE
uevent on every open() which lets udev run into a loop.
Verify GET_EVENT result against TUR and if it generates spurious
events for several times in a row, ignore the GET_EVENT events, and
trust only the TUR status.
This is the log of a USB stick with a (broken) fake CDROM drive:
scsi 5:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS
sd 5:0:0:0: Attached scsi generic sg3 type 0
scsi 5:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0
sd 5:0:0:0: [sdb] Attached SCSI removable disk
sr2: scsi3-mmc drive: 48x/48x tray
sr 5:0:0:1: Attached scsi CD-ROM sr2
sr 5:0:0:1: Attached scsi generic sg4 type 5
sr2: GET_EVENT and TUR disagree continuously, suppress GET_EVENT events
sd 5:0:0:0: [sdb] 31777279 512-byte logical blocks: (16.2 GB/15.1 GiB)
sd 5:0:0:0: [sdb] No Caching mode page present
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sd 5:0:0:0: [sdb] No Caching mode page present
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
-tj: Updated to consider only spurious GET_EVENT events among
different types of disagreement and allow using TUR for kernel
event polling after GET_EVENT is ignored.
Reported-By: Markus Rathgeb maggu2810@googlemail.com
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The below patch is for -stable only, upstream has a much larger patch
that contains the below hunk in commit a8b0ca17b8
Vince found that under certain circumstances software event overflows
go wrong and deadlock. Avoid trying to delete a timer from the timer
callback.
Reported-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit abe48b1082 upstream.
Since 2.6.36 (23016bf0d2), Linux prints the existence of "epb" in /proc/cpuinfo,
Since 2.6.38 (d5532ee7b4), the x86_energy_perf_policy(8) utility has
been available in-tree to update MSR_IA32_ENERGY_PERF_BIAS.
However, the typical BIOS fails to initialize the MSR, presumably
because this is handled by high-volume shrink-wrap operating systems...
Linux distros, on the other hand, do not yet invoke x86_energy_perf_policy(8).
As a result, WSM-EP, SNB, and later hardware from Intel will run in its
default hardware power-on state (performance), which assumes that users
care for performance at all costs and not for energy efficiency.
While that is fine for performance benchmarks, the hardware's intended default
operating point is "normal" mode...
Initialize the MSR to the "normal" by default during kernel boot.
x86_energy_perf_policy(8) is available to change the default after boot,
should the user have a different preference.
Signed-off-by: Len Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1107140051020.18606@x980
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit eda3913bb7 upstream.
The perf_event_attr struct has two __u32's at the top and
they need to be swapped individually.
With this change I was able to analyze a perf.data collected in a
32-bit PPC VM on an x86 system. I tested both 32-bit and 64-bit
binaries for the Intel analysis side; both read the PPC perf.data
file correctly.
-v2:
- changed the existing perf_event__attr_swap() to swap only elements
of perf_event_attr and exported it for use in swapping the
attributes in the file header
- updated swap_ops used for processing events
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: acme@ghostprotocols.net
Cc: peterz@infradead.org
Cc: paulus@samba.org
Link: http://lkml.kernel.org/r/1310754849-12474-1-git-send-email-dsahern@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 08a4a43fc4 upstream.
Builds for 32-bit perf binaries on a 64-bit host currently fail
with this error:
[...]
bench/../../../arch/x86/lib/memcpy_64.S: Assembler messages:
bench/../../../arch/x86/lib/memcpy_64.S:29: Error: bad register name `%rdi'
bench/../../../arch/x86/lib/memcpy_64.S:34: Error: invalid instruction suffix for `movs'
bench/../../../arch/x86/lib/memcpy_64.S:50: Error: bad register name `%rdi'
bench/../../../arch/x86/lib/memcpy_64.S:61: Error: bad register name `%rdi'
...
The problem is the detection of the host arch without considering passed in
flags. This change fixes 32-bit builds via:
make EXTRA_CFLAGS=-m32
and 64-bit builds still reference the memcpy_64.S.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1310420304-21452-1-git-send-email-dsahern@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 676b58c274 upstream.
A panic was observed when the device is failed to resume properly,
and there are no running interfaces. ieee80211_reconfig tries
to restart STA timers on unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1288aa4e80 upstream.
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 5911e963d3 upstream.
If expander discovery fails (sas_discover_expander()), remove the
expander from the port device list (sas_ex_discover_expander()),
before freeing it. Else the list is corrupted and, e.g., when we
attempt to send SMP commands to other devices, the kernel oopses.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fd1b6c4a69 upstream.
SCSI scanning of a channel:id:lun triplet in Linux works as follows
(function scsi_scan_target() in drivers/scsi/scsi_scan.c):
- If lun == SCAN_WILD_CARD, send a REPORT LUNS command to the target
and process the result.
- If lun != SCAN_WILD_CARD, send an INQUIRY command to the LUN
corresponding to the specified channel:id:lun triplet to verify
whether the LUN exists.
So a SCSI driver must either take the channel and target id values in
account in its quecommand() function or it should declare that it only
supports one channel and one target id.
Currently the ib_srp driver does neither. As a result scanning the
SCSI bus via e.g. rescan-scsi-bus.sh causes many duplicate SCSI
devices to be created. For each 0:0:L device, several duplicates are
created with the same LUN number and with (C:I) != (0:0). Fix this by
declaring that the ib_srp driver only supports one channel and one
target id.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 93b37905f7 upstream.
Between open(2) of a /dev/fw* and the first FW_CDEV_IOC_GET_INFO
ioctl(2) on it, the kernel already queues FW_CDEV_EVENT_BUS_RESET events
to be read(2) by the client. The get_info ioctl is practically always
issued right away after open, hence this condition only occurs if the
client opens during a bus reset, especially during a rapid series of bus
resets.
The problem with this condition is twofold:
- These bus reset events carry the (as yet undocumented) @closure
value of 0. But it is not the kernel's place to choose closures;
they are privat to the client. E.g., this 0 value forced from the
kernel makes it unsafe for clients to dereference it as a pointer to
a closure object without NULL pointer check.
- It is impossible for clients to determine the relative order of bus
reset events from get_info ioctl(2) versus those from read(2),
except in one way: By comparison of closure values. Again, such a
procedure imposes complexity on clients and reduces freedom in use
of the bus reset closure.
So, change the ABI to suppress queuing of bus reset events before the
first FW_CDEV_IOC_GET_INFO ioctl was issued by the client.
Note, this ABI change cannot be version-controlled. The kernel cannot
distinguish old from new clients before the first FW_CDEV_IOC_GET_INFO
ioctl.
We will try to back-merge this change into currently maintained stable/
longterm series, and we only document the new behaviour. The old
behavior is now considered a kernel bug, which it basically is.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
commit d873d79423 upstream.
On Jun 27 Linus Torvalds wrote:
> The correct error code for "I don't understand this ioctl" is ENOTTY.
> The naming may be odd, but you should think of that error value as a
> "unrecognized ioctl number, you're feeding me random numbers that I
> don't understand and I assume for historical reasons that you tried to
> do some tty operation on me".
[...]
> The EINVAL thing goes way back, and is a disaster. It predates Linux
> itself, as far as I can tell. You'll find lots of man-pages that have
> this line in it:
>
> EINVAL Request or argp is not valid.
>
> and it shows up in POSIX etc. And sadly, it generally shows up
> _before_ the line that says
>
> ENOTTY The specified request does not apply to the kind of object
> that the descriptor d references.
>
> so a lot of people get to the EINVAL, and never even notice the ENOTTY.
[...]
> At least glibc (and hopefully other C libraries) use a _string_ that
> makes much more sense: strerror(ENOTTY) is "Inappropriate ioctl for
> device"
So let's correct this in the <linux/firewire-cdev.h> ABI while it is
still young, relative to distributor adoption.
Side note: We return -ENOTTY not only on _IOC_TYPE or _IOC_NR mismatch,
but also on _IOC_SIZE mismatch. An ioctl with an unsupported size of
argument structure can be seen as an unsupported version of that ioctl.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 67ae7cf1ee upstream.
Some drivers (ab)use the ethtool_ops::get_regs operation to expose
only a hardware revision ID. Commit
a77f5db361 ('ethtool: Allocate register
dump buffer with vmalloc()') had the side-effect of breaking these, as
vmalloc() returns a null pointer for size=0 whereas kmalloc() did not.
For backward-compatibility, allow zero-length dumps again.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 94c5b41b32 upstream.
This patch add the missing dma_unmap().
Which solved the critical issue of system freeze on heavy load.
Michal Miroslaw's rejected patch:
[PATCH v2 10/46] net: jme: convert to generic DMA API
Pointed out the issue also, thank you Michal.
But the fix was incorrect. It would unmap needed address
when low memory.
Got lots of feedback from End user and Gentoo Bugzilla.
https://bugs.gentoo.org/show_bug.cgi?id=373109
Thank you all. :)
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f5bc1e755d upstream.
commit fec11dd9a0 caused
a regression when we have already mounted //server/share/a
and want to mount //server/share/a/b.
The problem is that lookup_one_len calls __lookup_hash
with nd pointer as NULL. Then __lookup_hash calls
do_revalidate in the case when dentry exists and we end
up with NULL pointer deference in cifs_d_revalidate:
if (nd->flags & LOOKUP_RCU)
return -ECHILD;
Fix this by checking nd for NULL.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0472ade031 upstream.
Decryping frames on key_miss handling shouldn't be done for Michael
MIC failed frames as h/w would have already decrypted such frames
successfully anyway.
Also leaving CRC and PHY error(where the frame is going to be dropped
anyway), we are left to prcoess Decrypt error for which s/w decrypt is
selected anway and so having key_miss as a separate check doesn't serve
anything. So making key_miss handling mutually exlusive with other RX
status handling makes much more sense.
This patch addresses an issue with STA not reporting MIC failure events
resulting in STA being disconnected immediately.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 98ab5c7755 upstream.
When ath6kl module was resumed while a scan was ongoing, for example during
suspend, the driver would crash in ar6k_cfg80211_scanComplete_event():
[26581.586440] Call Trace:
[26581.586440] [<f99ffeda>] ? ar6k_cfg80211_scanComplete_event+0xaa/0xaa [ath6kl]
[26581.586440] [<f9a0a020>] wmi_iterate_nodes+0xb/0xd [ath6kl]
[26581.586440] [<f99ffe78>] ar6k_cfg80211_scanComplete_event+0x48/0xaa [ath6kl]
[26581.586440] [<f9a038ae>] ar6000_close+0x77/0x7e [ath6kl]
[26581.586440] [<c139c25d>] __dev_close_many+0x87/0xab
[26581.586440] [<c139c30a>] dev_close_many+0x54/0xab
[26581.586440] [<c139c437>] rollback_registered_many+0xa5/0x19e
[26581.586440] [<c139c595>] rollback_registered+0x23/0x2f
[26581.586440] [<c139c5ed>] unregister_netdevice_queue+0x4c/0x69
[26581.586440] [<c139c6b2>] unregister_netdev+0x18/0x1f
[26581.586440] [<f9a00d4c>] ar6000_destroy+0xf8/0x115 [ath6kl]
[26581.586440] [<f9a0c765>] ar6k_cleanup_module+0x20/0x29 [ath6kl]
[26581.586440] [<c1062843>] sys_delete_module+0x181/0x1d9
[26581.586440] [<c105876b>] ? lock_release_holdtime+0x2b/0xcd
[26581.586440] [<c10b55dc>] ? sys_munmap+0x3b/0x42
[26581.586440] [<c14a99dc>] ? restore_all+0xf/0xf
[26581.586440] [<c14aeb6c>] sysenter_do_call+0x12/0x32
[26581.586440] Code: 89 53 6c 75 07 89 d8 e8 c0 ff ff ff 89 f0 e8 2c f2 a9 c7 5b 5e 5d c3 55 89 e5 57 56 53 89 c3 83 ec 08 89 55 f0 8d 78 04 89 4d ec <8b> b0 b8 00 00 00 46 89 b0 b8 00 00 00 89 f8 e8 ae ed a9 c7 8b
Fix the function not to iterate nodes when the scan is aborted. The nodes
are already freed when the module is being unloaded. Patch "ath6kl: Fix a
kernel panic furing suspend/resume" tried to fix this already but it wasn't
enough as a pointer was still used even after the null check. This patch
removes the null check entirely as the wmi structure is not accessed anymore
during module unload.
Also fix a bug where the status was checked as a bitfield with '&' operator.
But it's not a bitfield, just a regular (enum like) value.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b42a7b1bc7 upstream.
Drivers should not request firmware during resume. Fix ath6kl to
cache the firmware instead.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7be4ba24a3 upstream.
Since quite a few drivers are not managing to flag the cache as needing
to be resynced after suspend and it's a reasonable thing to do flag the
cache as needing sync automatically when suspending.
The expectation is that systems will mainly only keep the CODEC powered
when doing audio through the CODEC so we won't actually suspend the
device anyway; drivers which want to can override this behaviour when
they resume.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3012f43eaf upstream.
According to DM365 voice codec data sheet at [1], before starting
recording or playback, ADC/DAC modules should follow a reset and
enable cycle. Writing a 1 to the ADC/DAC bit in the register resets
the module and clearing the bit to 0 will enable the module. But the
driver seems to be doing the reverse of it.
[1] http://focus.ti.com/lit/ug/sprufi9b/sprufi9b.pdf
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 82d1d52103 upstream.
In davinci_vcif_trigger() function, a break() statement was missing
causing the davinci_vcif_stop() function to be called as a fallback
after calling davinci_vcif_start().
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6c7b3ea52e upstream.
While in sleep mode the CS# and other V3020 RTC GPIOs must be driven
high, otherwise V3020 RTC fails to keep the right time in sleep mode.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b830ac1d9a upstream.
Ben reported a lockup related to rtc. The lockup happens due to:
CPU0 CPU1
rtc_irq_set_state() __run_hrtimer()
spin_lock_irqsave(&rtc->irq_task_lock) rtc_handle_legacy_irq();
spin_lock(&rtc->irq_task_lock);
hrtimer_cancel()
while (callback_running);
So the running callback never finishes as it's blocked on
rtc->irq_task_lock.
Use hrtimer_try_to_cancel() instead and drop rtc->irq_task_lock while
waiting for the callback. Fix this for both rtc_irq_set_state() and
rtc_irq_set_freq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Ben Greear <greearb@candelatech.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3c5fec75e1 upstream.
Restoring the missing INDEX register value in musb_restore_context().
Without this suspend resume functionality is broken with offmode
enabled.
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
