[ Upstream commit 61ce04601e0d8265ec6d2ffa6df5a7e1bce64854 ]
Pass the correct list head to list_for_each_entry*() when looping through
the packet list.
Without this patch, reading the packet data via sysfs will show the data
incorrectly (because it starts at the wrong packet), and clearing the
packet list will result in a NULL pointer dereference.
Fixes: d19f359fbd ("platform/x86: dell_rbu: don't open code list_for_each_entry*()")
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Link: https://lore.kernel.org/r/20250609184659.7210-3-stuart.w.hayes@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dbd11796f3a8eb95647507befc41995458a4023 ]
The area of memory that contains the metrics table may contain garbage
when the cycle starts. This normally doesn't matter because the cycle
itself will populate it with valid data, however commit 9f5595d5f03fd
("platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep
cycles") started to use it during the check() phase. Depending upon
what garbage is in the table it's possible that the system will wait
2.5 seconds for even the first cycle, which will be visible to a user.
To prevent this from happening explicitly clear the table when logging
is started.
Fixes: 9f5595d5f03fd ("platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep cycles")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250603132412.3555302-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36305857b1ead8f6ca033a913162ebc09bee0b43 ]
This reverts commit 4700a00755.
It breaks target-module@2b300050 ("ti,sysc-omap2") probe on AM62x in a case
when minimally-configured system tries to network-boot:
[ 6.888776] probe of 2b300050.target-module returned 517 after 258 usecs
[ 17.129637] probe of 2b300050.target-module returned 517 after 708 usecs
[ 17.137397] platform 2b300050.target-module: deferred probe pending: (reason unknown)
[ 26.878471] Waiting up to 100 more seconds for network.
There are minimal configurations possible when the deferred device is not
being probed any more (because everything else has been successfully
probed) and deferral lists are not processed any more.
Stable mmc enumeration can be achieved by filling /aliases node properly
(4700a00755 commit's rationale).
After revert:
[ 9.006816] IP-Config: Complete:
[ 9.010058] device=lan0, ...
Tested-by: Andreas Kemnade <andreas@kemnade.info> # GTA04, Panda, BT200
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20250401090643.2776793-1-alexander.sverdlin@siemens.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39bb67edcc582b3b386a9ec983da67fa8a10ec03 ]
The current code around TEE_IOCTL_PARAM_SIZE() is a bit wrong on
32-bit kernels: Multiplying a user-provided 32-bit value with the
size of a structure can wrap around on such platforms.
Fix it by using saturating arithmetic for the size calculation.
This has no security consequences because, in all users of
TEE_IOCTL_PARAM_SIZE(), the subsequent kcalloc() implicitly checks
for wrapping.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Tested-by: Rouven Czerwinski <rouven.czerwinski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cedc1b63394a866bf8663a3e40f4546f1d28c8d8 ]
It looks like attempting to write to the "store_modes" sysfs node will
run afoul of unregistered consoles:
UBSAN: array-index-out-of-bounds in drivers/video/fbdev/core/fbcon.c:122:28
index -1 is out of range for type 'fb_info *[32]'
...
fbcon_info_from_console+0x192/0x1a0 drivers/video/fbdev/core/fbcon.c:122
fbcon_new_modelist+0xbf/0x2d0 drivers/video/fbdev/core/fbcon.c:3048
fb_new_modelist+0x328/0x440 drivers/video/fbdev/core/fbmem.c:673
store_modes+0x1c9/0x3e0 drivers/video/fbdev/core/fbsysfs.c:113
dev_attr_store+0x55/0x80 drivers/base/core.c:2439
static struct fb_info *fbcon_registered_fb[FB_MAX];
...
static signed char con2fb_map[MAX_NR_CONSOLES];
...
static struct fb_info *fbcon_info_from_console(int console)
...
return fbcon_registered_fb[con2fb_map[console]];
If con2fb_map contains a -1 things go wrong here. Instead, return NULL,
as callers of fbcon_info_from_console() are trying to compare against
existing "info" pointers, so error handling should kick in correctly.
Reported-by: syzbot+a7d4444e7b6e743572f7@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/679d0a8f.050a0220.163cdc.000c.GAE@google.com/
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1b01e46a3db5ad44d1e4691ba37c1e0832cd5cf ]
Currently, for 160 MHz bandwidth, center frequency1 and
center frequency2 are not passed correctly to the firmware.
Set center frequency1 as the center frequency
of the primary 80 MHz channel segment and center frequency2 as
the center frequency of the 160 MHz channel and pass the values
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Suraj P Kizhakkethil <quic_surapk@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250304095315.3050325-2-quic_surapk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60031d9c3589c7983fd1deb4a4c0bebf0929890e ]
In the current ath12k implementation, the CE addresses
CE_HOST_IE_ADDRESS and CE_HOST_IE_2_ADDRESS are incorrect. These
values were inherited from ath11k, but ath12k does not currently use
them.
However, the Ath12k AHB support relies on these addresses. Therefore,
correct the CE addresses for ath12k.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-2-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8669a27016354dfa8bf3c954255cb9f3583bae ]
To handle the Lenovo unexpected wakeup issue [1], previously we revert
commit 166a490f59ac ("wifi: ath11k: support hibernation"). So currently
WLAN target is put into WoWLAN mode during suspend. This is a temporary
solution as it does not work on machines where WLAN power is cut off.
The thought here is that we do WoWLAN suspend on Lenovo machines while
do non-WoWLAN suspend (which is done in the reverted commit) on other
machines. This requires us to identify Lenovo machines from others.
For that purpose, read board vendor and product name from DMI interface,
match it against all known affected machines. If there is a match, choose
WoWLAN suspend mode, else choose non-WoWLAN mode. Save the mode in ab
for later reference.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-1-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c056ec6dd1654b1420dafbbe2a69718850e6ff2 ]
The cn10k_free_matchall_ipolicer() calls the cn10k_map_unmap_rq_policer()
for each queue in a for loop without checking for any errors.
Check the return value of the cn10k_map_unmap_rq_policer() function during
each loop, and report a warning if the function fails.
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250408032602.2909-1-vulab@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a07e3af4973402fa199a80036c10060b922c92c ]
It is desireable to push the hardware accelerator to also
process non-segmented TCP frames: we pass the skb->len
to the "TOE/TSO" offloader and it will handle them.
Without this quirk the driver becomes unstable and lock
up and and crash.
I do not know exactly why, but it is probably due to the
TOE (TCP offload engine) feature that is coupled with the
segmentation feature - it is not possible to turn one
part off and not the other, either both TOE and TSO are
active, or neither of them.
Not having the TOE part active seems detrimental, as if
that hardware feature is not really supposed to be turned
off.
The datasheet says:
"Based on packet parsing and TCP connection/NAT table
lookup results, the NetEngine puts the packets
belonging to the same TCP connection to the same queue
for the software to process. The NetEngine puts
incoming packets to the buffer or series of buffers
for a jumbo packet. With this hardware acceleration,
IP/TCP header parsing, checksum validation and
connection lookup are offloaded from the software
processing."
After numerous tests with the hardware locking up after
something between minutes and hours depending on load
using iperf3 I have concluded this is necessary to stabilize
the hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250408-gemini-ethernet-tso-always-v1-1-e669f932359c@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db03c20c0850dc8d2bcabfa54b9438f7d666c863 ]
1. After we start atomic write in a database file, before committing
all data, we'd better not set inode w/ vfs dirty status to avoid
redundant updates, instead, we only set inode w/ atomic dirty status.
2. After we commit all data, before committing metadata, we need to
clear atomic dirty status, and set vfs dirty status to allow vfs flush
dirty inode.
Cc: Daeho Jeong <daehojeong@google.com>
Reported-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Reviewed-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4145f00227ee80f21ab274e9cd9c09758e9bcf3d ]
ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come
up ("carrier off"), despite the built-in 100BASE-FX PHY positive link
indication. The internal PHY is configured (using EEPROM) in fixed
100 Mbps full duplex mode.
The primary problem appears to be using carrier_netif_{on,off}() while,
at the same time, delegating carrier management to phylink. Use only the
latter and remove "manual control" in the asix driver.
I don't have any other AX88772 board here, but the problem doesn't seem
specific to a particular board or settings - it's probably
timing-dependent.
Remove unused asix_adjust_link() as well.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/m3plhmdfte.fsf_-_@t19.piap.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a808691df39b52cd9db861b118e88e18b63e2299 ]
In case the rule already exists and another VSI wants to subscribe to it
new VSI list is being created and both VSIs are moved to it.
Currently, the check for already existing VSI with the same rule is done
based on fdw_id.hw_vsi_id, which applies only to LOOKUP_RX flag.
Change it to vsi_handle. This is software VSI ID, but it can be applied
here, because vsi_map itself is also based on it.
Additionally change return status in case the VSI already exists in the
VSI map to "Already exists". Such case should be handled by the caller.
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae82eaf4aeea060bb736c3e20c0568b67c701d7d ]
The strlcat() with FORTIFY support is triggering a panic because it
thinks the target buffer will overflow although the correct target
buffer size is passed in.
Anyway, instead of memset() with 0 followed by a strlcat(), just use
memcpy() and ensure that the resulting buffer is NULL terminated.
BIOSVersion is only used for the lpfc_printf_log() which expects a
properly terminated string.
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Link: https://lore.kernel.org/r/20250409-fix-lpfc-bios-str-v1-1-05dac9e51e13@kernel.org
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce7aec6b1f74b0a46b901ab8de1f7bd0515f733 ]
With hardware grouping, during reboot, whenever a device is removed, it
powers down itself and all its partner devices in the same group. Now this
is done by all devices and hence there is multiple power down for devices
and hence the following error messages can be seen:
ath12k_pci 0002:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0002:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0003:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0003:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0004:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0004:01:00.0: failed to set mhi state: POWER_OFF(3)
To prevent this, check if the ATH12K_PCI_FLAG_INIT_DONE flag is already
set before powering down. If it is set, it indicates that another partner
device has already performed the power down, and this device can skip this
step.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-3-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ede3f8b4b4b399b0ca41e44959f80d5cf84fc98 ]
At startup, the driver just assumes that all registers have their
default values. But after a soft reset, the chip will just be in the
state it was, and some pins may have been configured as outputs. Any
modification of the output register will cause these pins to be driven
low, which leads to unexpected/unwanted effects. To prevent this from
happening, set the chip's IO configuration register to a known safe
mode (all inputs) before toggling any other bits.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lore.kernel.org/20250314151803.28903-1-mike.looijmans@topic.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09737cb80b8686ffca4ed1805fee745d5c85604d ]
of_get_mac_address() might fetch the MAC address from NVMEM and that
driver might not have been loaded. In that case, -EPROBE_DEFER is
returned. Right now, this will trigger an immediate fallback to
am65_cpsw_am654_get_efuse_macid() possibly resulting in a random MAC
address although the MAC address is stored in the referenced NVMEM.
Fix it by handling the -EPROBE_DEFER return code correctly. This also
means that the creation of the MDIO device has to be moved to a later
stage as -EPROBE_DEFER must not be returned after child devices are
created.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250414084336.4017237-3-mwalle@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20c76dadc783759fd3819d289c72be590660cc8b ]
FDB entries are allocated in an atomic context as they can be added from
the data path when learning is enabled.
After converting the FDB hash table to rhashtable, the insertion rate
will be much higher (*) which will entail a much higher rate of per-CPU
allocations via dst_cache_init().
When adding a large number of entries (e.g., 256k) in a batch, a small
percentage (< 0.02%) of these per-CPU allocations will fail [1]. This
does not happen with the current code since the insertion rate is low
enough to give the per-CPU allocator a chance to asynchronously create
new chunks of per-CPU memory.
Given that:
a. Only a small percentage of these per-CPU allocations fail.
b. The scenario where this happens might not be the most realistic one.
c. The driver can work correctly without dst caches. The dst_cache_*()
APIs first check that the dst cache was properly initialized.
d. The dst caches are not always used (e.g., 'tos inherit').
It seems reasonable to not treat these allocation failures as fatal.
Therefore, do not bail when dst_cache_init() fails and suppress warnings
by specifying '__GFP_NOWARN'.
[1] percpu: allocation failed, size=40 align=8 atomic=1, atomic alloc failed, no space left
(*) 97% reduction in average latency of vxlan_fdb_update() when adding
256k entries in a batch.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250415121143.345227-14-idosch@nvidia.com
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b30ae9adb047dd0a7982975ec3933c529537026 ]
When a bridge port STP state is changed from BLOCKING/DISABLED to
FORWARDING, the port's igmp query timer will NOT re-arm itself if the
bridge has been configured as per-VLAN multicast snooping.
Solve this by choosing the correct multicast context(s) to enable/disable
port multicast based on whether per-VLAN multicast snooping is enabled or
not, i.e. using per-{port, VLAN} context in case of per-VLAN multicast
snooping by re-implementing br_multicast_enable_port() and
br_multicast_disable_port() functions.
Before the patch, the IGMP query does not happen in the last step of the
following test sequence, i.e. no growth for tx counter:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# bridge link set dev swp1 state 0
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge link set dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
After the patch, the IGMP query happens in the last step of the test:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# bridge link set dev swp1 state 0
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge link set dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
3
Signed-off-by: Yong Wang <yongwang@nvidia.com>
Reviewed-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c131043eaf1be2a6cc2d228f92ceb626fbcc0f3 ]
When the vlan STP state is changed, which could be manipulated by
"bridge vlan" commands, similar to port STP state, this also impacts
multicast behaviors such as igmp query. In the scenario of per-VLAN
snooping, there's a need to update the corresponding multicast context
to re-arm the port query timer when vlan state becomes "forwarding" etc.
Update br_vlan_set_state() function to enable vlan multicast context
in such scenario.
Before the patch, the IGMP query does not happen in the last step of the
following test sequence, i.e. no growth for tx counter:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# sleep 1
# bridge vlan set vid 1 dev swp1 state 4
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge vlan set vid 1 dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
After the patch, the IGMP query happens in the last step of the test:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# sleep 1
# bridge vlan set vid 1 dev swp1 state 4
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge vlan set vid 1 dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
3
Signed-off-by: Yong Wang <yongwang@nvidia.com>
Reviewed-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a4a6a22552ca9d723f28a1fe35eab1b9b3d8b33 ]
Currently for MLO, sending out multicast frames on each link is handled by
mac80211 only when IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX flag is not set.
Dynamic VLAN multicast traffic utilizes software encryption.
Due to this, mac80211 should handle transmitting multicast frames on
all links for multicast VLAN traffic.
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Link: https://patch.msgid.link/20250325213125.1509362-4-muna.sinada@oss.qualcomm.com
[remove unnecessary parentheses]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ae6c9c7315d844fbc15afe393f5ba5e5771126 ]
In lpfc_check_sli_ndlp(), the get_job_els_rsp64_did remote_id assignment
does not apply for GEN_REQUEST64 commands as it only has meaning for a
ELS_REQUEST64 command. So, if (iocb->ndlp == ndlp) is false, we could
erroneously return the wrong value. Fix by replacing the fallthrough
statement with a break statement before the remote_id check.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20250425194806.3585-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e64c387c942229c551d0f23de4d9993d3a2acb6 ]
Recently as a side-effect of
commit ac053946f5c4 ("compiler.h: introduce TYPEOF_UNQUAL() macro")
issues were observed in deduplication between modules and kernel BTF
such that a large number of kernel types were not deduplicated so
were found in module BTF (task_struct, bpf_prog etc). The root cause
appeared to be a failure to dedup struct types, specifically those
with members that were pointers with __percpu annotations.
The issue in dedup is at the point that we are deduplicating structures,
we have not yet deduplicated reference types like pointers. If multiple
copies of a pointer point at the same (deduplicated) integer as in this
case, we do not see them as identical. Special handling already exists
to deal with structures and arrays, so add pointer handling here too.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250429161042.2069678-1-alan.maguire@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596a977b34a722c00245801a5774aa79cec4e81d ]
The ddrphy is supplied by the dpll, but due to the limited number of PLLs
on the rk3036, the dpll also is used for other periperhals, like the GPU.
So it happened, when the Lima driver turned off the gpu clock, this in
turn also disabled the dpll and thus the ram.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503202532.992033-4-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf1b684a06170d253b47d6a5287821de976435bd ]
When processing a PREQ the code would always check whether we have a
mesh path locally and reply accordingly. However, when forwarding is
disabled then we should not reply with this information as we will not
forward data packets down that path.
Move the check for dot11MeshForwarding up in the function and skip the
mesh path lookup in that case. In the else block, set forward to false
so that the rest of the function becomes a no-op and the
dot11MeshForwarding check does not need to be duplicated.
This explains an effect observed in the Freifunk community where mesh
forwarding is disabled. In that case a mesh with three STAs and only bad
links in between them, individual STAs would occionally have indirect
mpath entries. This should not have happened.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Reviewed-by: Rouven Czerwinski <rouven@czerwinskis.de>
Link: https://patch.msgid.link/20250430191042.3287004-1-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ecf56f4b66011b583644bf9a62188d05dfcd78c ]
The MSE102x doesn't provide any interrupt register, so the only way
to handle the level interrupt is to fetch the whole packet from
the MSE102x internal buffer via SPI. So in cases the interrupt
handler fails to do this, it should return IRQ_NONE. This allows
the core to disable the interrupt in case the issue persists
and prevent an interrupt storm.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20250509120435.43646-6-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c0829788a6e6e165846b9bedd0b908ef16260b6 ]
The statistics are incremented with raw_cpu_inc() assuming it always
happens with bottom half disabled. Without per-CPU locking in
local_bh_disable() on PREEMPT_RT this is no longer true.
Use this_cpu_inc() on PREEMPT_RT for the increment to not worry about
preemption.
Cc: David Ahern <dsahern@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20250512092736.229935-4-bigeasy@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed16618c380c32c68c06186d0ccbb0d5e0586e59 ]
TL;DR: SGX page reclaim touches the page to copy its contents to
secondary storage. SGX instructions do not gracefully handle machine
checks. Despite this, the existing SGX code will try to reclaim pages
that it _knows_ are poisoned. Avoid even trying to reclaim poisoned pages.
The longer story:
Pages used by an enclave only get epc_page->poison set in
arch_memory_failure() but they currently stay on sgx_active_page_list until
sgx_encl_release(), with the SGX_EPC_PAGE_RECLAIMER_TRACKED flag untouched.
epc_page->poison is not checked in the reclaimer logic meaning that, if other
conditions are met, an attempt will be made to reclaim an EPC page that was
poisoned. This is bad because 1. we don't want that page to end up added
to another enclave and 2. it is likely to cause one core to shut down
and the kernel to panic.
Specifically, reclaiming uses microcode operations including "EWB" which
accesses the EPC page contents to encrypt and write them out to non-SGX
memory. Those operations cannot handle MCEs in their accesses other than
by putting the executing core into a special shutdown state (affecting
both threads with HT.) The kernel will subsequently panic on the
remaining cores seeing the core didn't enter MCE handler(s) in time.
Call sgx_unmark_page_reclaimable() to remove the affected EPC page from
sgx_active_page_list on memory error to stop it being considered for
reclaiming.
Testing epc_page->poison in sgx_reclaim_pages() would also work but I assume
it's better to add code in the less likely paths.
The affected EPC page is not added to &node->sgx_poison_page_list until
later in sgx_encl_release()->sgx_free_epc_page() when it is EREMOVEd.
Membership on other lists doesn't change to avoid changing any of the
lists' semantics except for sgx_active_page_list. There's a "TBD" comment
in arch_memory_failure() about pre-emptive actions, the goal here is not
to address everything that it may imply.
This also doesn't completely close the time window when a memory error
notification will be fatal (for a not previously poisoned EPC page) --
the MCE can happen after sgx_reclaim_pages() has selected its candidates
or even *inside* a microcode operation (actually easy to trigger due to
the amount of time spent in them.)
The spinlock in sgx_unmark_page_reclaimable() is safe because
memory_failure() runs in process context and no spinlocks are held,
explicitly noted in a mm/memory-failure.c comment.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: balrogg@gmail.com
Cc: linux-sgx@vger.kernel.org
Link: https://lore.kernel.org/r/20250508230429.456271-1-andrew.zaborowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd171461b90a2d2cf230943df60d580174633718 ]
tcp_rcv_state_process() must tweak tp->advmss for TS enabled flows
before the call to tcp_init_transfer() / tcp_init_buffer_space().
Otherwise tp->rcvq_space.space is off by 120 bytes
(TCP_INIT_CWND * TCPOLEN_TSTAMP_ALIGNED).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Link: https://patch.msgid.link/20250513193919.1089692-7-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b879dcb1aeeca278eacaac0b1e2425b1c7599f9f ]
tcp_rcv_rtt_update() goal is to maintain an estimation of the RTT
in tp->rcv_rtt_est.rtt_us, used by tcp_rcv_space_adjust()
When TCP TS are enabled, tcp_rcv_rtt_update() is using
EWMA to smooth the samples.
Change this to immediately latch the incoming value if it
is lower than tp->rcv_rtt_est.rtt_us, so that tcp_rcv_space_adjust()
does not overshoot tp->rcvq_space.space and sk->sk_rcvbuf.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250513193919.1089692-8-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
