[ Upstream commit e3d4571955 ]
The SMSM driver detects interrupt edges by tracking the last state
it has seen (and has triggered the interrupt handler for). This works
fine, but only if the interrupt does not change state while masked.
For example, if an interrupt is unmasked while the state is HIGH,
the stored last_value for that interrupt might still be LOW. Then,
when the remote processor triggers smsm_intr() we assume that nothing
has changed, even though the state might have changed from HIGH to LOW.
Attempt to fix this by checking the current remote state before
unmasking an IRQ. Use atomic operations to avoid the interrupt handler
from interfering with the unmask function.
This fixes modem crashes in some edge cases with the BAM-DMUX driver.
Specifically, the BAM-DMUX interrupt handler is not called for the
HIGH -> LOW smsm state transition if the BAM-DMUX driver is loaded
(and therefore unmasks the interrupt) after the modem was already started:
qcom-q6v5-mss 4080000.remoteproc: fatal error received: a2_task.c:3188:
Assert FALSE failed: A2 DL PER deadlock timer expired waiting for Apps ACK
Fixes: c97c4090ff ("soc: qcom: smsm: Add driver for Qualcomm SMSM")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712135703.324748-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e00392a89 ]
PME signaling is only enabled by __pci_enable_wake() if the target
device can signal PME from the given target power state (to avoid
pointless reconfiguration of the device), but if the hierarchy above
the device goes into D3cold, the device itself will end up in D3cold
too, so if it can signal PME from D3cold, it should be enabled to
do so in __pci_enable_wake().
[Note that if the device does not end up in D3cold and it cannot
signal PME from the original target power state, it will not signal
PME, so in that case the behavior does not change.]
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 5bcc2fb4e8 ("PCI PM: Simplify PCI wake-up code")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da9f215068 ]
It is inconsistent to return PCI_D0 from pci_target_state() instead
of the original target state if 'wakeup' is true and the device
cannot signal PME from D0.
This only happens when the device cannot signal PME from the original
target state and any shallower power states (including D0) and that
case is effectively equivalent to the one in which PME singaling is
not supported at all. Since the original target state is returned in
the latter case, make the function do that in the former one too.
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 666ff6f83e ("PCI/PM: Avoid using device_may_wakeup() for runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09ea9719a4 ]
Currently the call to find_format can potentially return a NULL to
fmt and the nullpointer is later dereferenced on the assignment of
pixmp->num_planes = fmt->num_planes. Fix this by adding a NULL pointer
check and returning NULL for the failure case.
Addresses-Coverity: ("Dereference null return")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fa54bc713 ]
If em28xx_ir_init fails, it would decrease the refcount of dev. However,
in the em28xx_ir_fini, when ir is NULL, it goes to ref_put and decrease
the refcount of dev. This will lead to a refcount bug.
Fix this bug by removing the kref_put in the error handling code
of em28xx_ir_init.
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 7 at lib/refcount.c:28 refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Modules linked in:
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.13.0 #3
Workqueue: usb_hub_wq hub_event
RIP: 0010:refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Call Trace:
kref_put.constprop.0+0x60/0x85 include/linux/kref.h:69
em28xx_usb_disconnect.cold+0xd7/0xdc drivers/media/usb/em28xx/em28xx-cards.c:4150
usb_unbind_interface+0xbf/0x3a0 drivers/usb/core/driver.c:458
__device_release_driver drivers/base/dd.c:1201 [inline]
device_release_driver_internal+0x22a/0x230 drivers/base/dd.c:1232
bus_remove_device+0x108/0x160 drivers/base/bus.c:529
device_del+0x1fe/0x510 drivers/base/core.c:3540
usb_disable_device+0xd1/0x1d0 drivers/usb/core/message.c:1419
usb_disconnect+0x109/0x330 drivers/usb/core/hub.c:2221
hub_port_connect drivers/usb/core/hub.c:5151 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5440 [inline]
port_event drivers/usb/core/hub.c:5586 [inline]
hub_event+0xf81/0x1d40 drivers/usb/core/hub.c:5668
process_one_work+0x2c9/0x610 kernel/workqueue.c:2276
process_scheduled_works kernel/workqueue.c:2338 [inline]
worker_thread+0x333/0x5b0 kernel/workqueue.c:2424
kthread+0x188/0x1d0 kernel/kthread.c:319
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: ac56886371 ("media: em28xx: Fix possible memory leak of em28xx struct")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64f67b5240 ]
Some 2-in-1s with a detachable (USB) keyboard(dock) have mute-LEDs in
the speaker- and/or mic-mute keys on the keyboard.
Examples of this are the Lenovo Thinkpad10 tablet (with its USB kbd-dock)
and the HP x2 10 series.
The detachable nature of these keyboards means that the keyboard and
thus the mute LEDs may show up after the user (or userspace restoring
old mixer settings) has muted the speaker and/or mic.
Current LED-class devices with a default_trigger of "audio-mute" or
"audio-micmute" initialize the brightness member of led_classdev with
ledtrig_audio_get() before registering the LED.
This makes the software state after attaching the keyboard match the
actual audio mute state, e.g. cat /sys/class/leds/foo/brightness will
show the right value.
But before this commit nothing was actually calling the led_classdev's
brightness_set[_blocking] callback so the value returned by
ledtrig_audio_get() was never actually being sent to the hw, leading
to the mute LEDs staying in their default power-on state, after
attaching the keyboard, even if ledtrig_audio_get() returned a different
state.
This could be fixed by having the individual LED drivers call
brightness_set[_blocking] themselves after registering the LED,
but this really is something which should be done by a led-trigger
activate callback.
Add an activate callback for this, fixing the issue of the
mute LEDs being out of sync after (re)attaching the keyboard.
Cc: Takashi Iwai <tiwai@suse.de>
Fixes: faa2541f5b ("leds: trigger: Introduce audio mute LED trigger")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e1baaaa24 ]
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 8cd7d6daba ("leds: lt3593: Add device tree probing glue")
Cc: Daniel Mack <daniel@zonque.org>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f16a3bb69a ]
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab1 ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca34a13f7 ]
Syzbot reported warning in netlbl_cipsov4_add(). The
problem was in too big doi_def->map.std->lvl.local_size
passed to kcalloc(). Since this value comes from userpace there is
no need to warn if value is not correct.
The same problem may occur with other kcalloc() calls in
this function, so, I've added __GFP_NOWARN flag to all
kcalloc() calls there.
Reported-and-tested-by: syzbot+cdd51ee2e6b0b2e18c0d@syzkaller.appspotmail.com
Fixes: 96cb8e3313 ("[NetLabel]: CIPSOv4 and Unlabeled packet integration")
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d428e6fe ]
In cpuset_hotplug_workfn(), the detection of whether the cpu list
has been changed is done by comparing the effective cpus of the top
cpuset with the cpu_active_mask. However, in the rare case that just
all the CPUs in the subparts_cpus are offlined, the detection fails
and the partition states are not updated correctly. Fix it by forcing
the cpus_updated flag to true in this particular case.
Fixes: 4b842da276 ("cpuset: Make CPU hotplug work with partition")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c43f3865c ]
TIR's rx_hash_field_selector_inner can be enabled only when
tunneled_offload_en = 1. tunneled_offload_en is filled according to the
tunneled_offload_en field in struct mlx5e_params, which is false in the
IPoIB profile. On the other hand, the IPoIB profile passes inner_ttc =
true to mlx5e_create_indirect_tirs, which potentially allows the latter
function to attempt to create inner indirect TIRs without having
tunneled_offload_en set.
This commit prohibits this behavior by passing inner_ttc = false to
mlx5e_create_indirect_tirs. The latter function won't attempt to create
inner indirect TIRs.
As inner indirect TIRs are not created in the IPoIB profile (this commit
blocks it explicitly, and even before they would have failed to be
created), the call to mlx5e_create_inner_ttc_table in
mlx5i_create_flow_steering is a no-op and can be removed.
Fixes: 46dc933cee ("net/mlx5e: Provide explicit directive if to create inner indirect tirs")
Fixes: 458821c72b ("net/mlx5e: IPoIB, Add inner TTC table to IPoIB flow steering")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ccc373b0 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 087a1d8b4e ("ARM: dts: meson8b: ec100: add the VDDEE regulator")
Fixes: 3e7db1c1b7 ("ARM: dts: meson8b: ec100: improve the description of the regulators")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 876228e9f9 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 524d96083b ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator")
Fixes: 8bdf38be71 ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator")
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed typo in commit s/observer/observe/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44cf630bcb ]
We are seeing "imprecise external abort (0x1406)" errors during boot
(which then cause the whole board to hang) on Meson8 (but not Meson8m2).
These are observed while trying to access the GPU's registers when the
MALI clock is running at it's default setting of 24MHz. The 3.10 vendor
kernel uses 318.75MHz as "default" GPU frequency. Using that makes the
"imprecise external aborts" go away.
Add the assigned-clocks and assigned-clock-rates properties to also bump
the MALI clock to 318.75MHz before accessing any of it's registers.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210711214023.2163565-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 525e2f9fd0 ]
st->bucket stores the current bucket number.
st->offset stores the offset within this bucket that is the sk to be
seq_show(). Thus, st->offset only makes sense within the same
st->bucket.
These two variables are an optimization for the common no-lseek case.
When resuming the seq_file iteration (i.e. seq_start()),
tcp_seek_last_pos() tries to continue from the st->offset
at bucket st->bucket.
However, it is possible that the bucket pointed by st->bucket
has changed and st->offset may end up skipping the whole st->bucket
without finding a sk. In this case, tcp_seek_last_pos() currently
continues to satisfy the offset condition in the next (and incorrect)
bucket. Instead, regardless of the offset value, the first sk of the
next bucket should be returned. Thus, "bucket == st->bucket" check is
added to tcp_seek_last_pos().
The chance of hitting this is small and the issue is a decade old,
so targeting for the next tree.
Fixes: a8b690f98b ("tcp: Fix slowness in read /proc/net/tcp")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210701200541.1033917-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2dce224f46 upstream.
__peernet2id() can be protected by RCU as it only calls idr_for_each(),
which is RCU-safe, and never modifies the nsid table.
rtnl_net_dumpid() can also do lockless lookups. It does two nested
idr_for_each() calls on nsid tables (one direct call and one indirect
call because of rtnl_net_dumpid_one() calling __peernet2id()). The
netnsid tables are never updated. Therefore it is safe to not take the
nsid_lock and run within an RCU-critical section instead.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
[ Upstream commit 9af417610b ]
The bounds check of id is off-by-one and the comparison should
be >= rather >. Currently the WARN_ON_ONCE check does not stop
the out of range indexing of &ldev->ctx.table[id] so also add
a return path if the bounds are out of range.
Addresses-Coverity: ("Illegal address computation").
Fixes: 5609c185f2 ("6lowpan: iphc: add support for stateful compression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59da0b38bc ]
Smatch complains that some of these struct members are not initialized
leading to a stack information disclosure:
net/bluetooth/sco.c:778 sco_conn_defer_accept() warn:
check that 'cp.retrans_effort' doesn't leak information
This seems like a valid warning. I've added a default case to fix
this issue.
Fixes: 2f69a82acf ("Bluetooth: Use voice setting in deferred SCO connection request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44693d74f5 ]
The frame memory control register value is currently determined
before userspace selects the final capture format and never corrected.
Update ctx->frame_mem_ctrl in __coda_start_decoding() to fix decoding
into YUV420 or YVU420 capture buffers.
Reported-by: Andrej Picej <andrej.picej@norik.com>
Fixes: 497e6b8559 ("media: coda: add sequence initialization work")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f5885a775 ]
In go7007_alloc() kzalloc() is used for struct go7007
allocation. It means that there is no need in zeroing
any members, because kzalloc will take care of it.
Removing these reduntant initialization steps increases
execution speed a lot:
Before:
+ 86.802 us | go7007_alloc();
After:
+ 29.595 us | go7007_alloc();
Fixes: 866b8695d6 ("Staging: add the go7007 video driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131ae388b8 ]
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error
message, and then continues to set DVB_USB_STATE_I2C. This affects the
logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap
even if the i2c_add_adapter fails.
Fix this by returning at the failure of i2c_add_adapter and then move
dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init.
Fixes: 13a79f14ab ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 797c061ad7 ]
If vp702x_usb_in_op fails, the mac address is not initialized.
And vp702x_read_mac_addr does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of vp702x_usb_in_op.
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5453769f7 ]
If dibusb_read_eeprom_byte fails, the mac address is not initialized.
And nova_t_read_mac_address does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of dibusb_read_eeprom_byte.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43b3a989b ]
rpmhpd_aggregate_corner() takes a corner as parameter, but in
rpmhpd_power_off() the code requests the level of the first corner
instead.
In all (known) current cases the first corner has level 0, so this
change should be a nop, but in case that there's a power domain with a
non-zero lowest level this makes sure that rpmhpd_power_off() actually
requests the lowest level - which is the closest to "power off" we can
get.
While touching the code, also skip the unnecessary zero-initialization
of "ret".
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210703005416.2668319-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75f0fc7b48 ]
In bpf_patch_insn_data(), we first use the bpf_patch_insn_single() to
insert new instructions, then use adjust_insn_aux_data() to adjust
insn_aux_data. If the old env->prog have no enough room for new inserted
instructions, we use bpf_prog_realloc to construct new_prog and free the
old env->prog.
There have two errors here. First, if adjust_insn_aux_data() return
ENOMEM, we should free the new_prog. Second, if adjust_insn_aux_data()
return ENOMEM, bpf_patch_insn_data() will return NULL, and env->prog has
been freed in bpf_prog_realloc, but we will use it in bpf_check().
So in this patch, we make the adjust_insn_aux_data() never fails. In
bpf_patch_insn_data(), we first pre-malloc memory for the new
insn_aux_data, then call bpf_patch_insn_single() to insert new
instructions, at last call adjust_insn_aux_data() to adjust
insn_aux_data.
Fixes: 8041902dae ("bpf: adjust insn_aux_data when patching insns")
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210714101815.164322-1-hefengqing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb0145821 ]
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
Fixes: cb496cd472 ("media: cxd2880-spi: Add optional vcc regulator")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea3e1c36e3 ]
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2294a7299f ]
MCDDRCFG is a per-channel register and uses bit{0,1} to indicate
the NVDIMM presence on DIMM slot{0,1}. Current i10nm_edac driver
wrongly uses MCDDRCFG as per-DIMM register and fails to detect
the NVDIMM.
Fix it by reading MCDDRCFG as per-channel register and using its
bit{0,1} to check whether the NVDIMM is populated on DIMM slot{0,1}.
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Fan Du <fan.du@intel.com>
Tested-by: Wen Jin <wen.jin@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210818175701.1611513-2-tony.luck@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26cfc0dbe4 ]
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98e47570ba ]
In commit e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting
and setting the voltage"), all calls to get/set the voltage of the
control regulator were switched to unlocked versions to avoid deadlocks.
However, the call in the probe path is done without regulator locks
held. In this case the locked version should be used.
Switch back to the locked regulator_get_voltage() in the probe path to
avoid any mishaps.
Fixes: e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210825033704.3307263-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea35e0d5df ]
Address a kbuild issue where a developer created an ECDSA key for signing
kernel modules and then builds an older version of the kernel, when bi-
secting the kernel for example, that does not support ECDSA keys.
If openssl is installed, trigger the creation of an RSA module signing
key if it is not an RSA key.
Fixes: cfc411e7ff ("Move certificate handling to its own directory")
Cc: David Howells <dhowells@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 462354d986 ]
Replace vf_mask type with unsigned long to avoid a stack-out-of-bound.
This is to fix the following warning reported by KASAN the first time
adf_msix_isr_ae() gets called.
[ 692.091987] BUG: KASAN: stack-out-of-bounds in find_first_bit+0x28/0x50
[ 692.092017] Read of size 8 at addr ffff88afdf789e60 by task swapper/32/0
[ 692.092076] Call Trace:
[ 692.092089] <IRQ>
[ 692.092101] dump_stack+0x9c/0xcf
[ 692.092132] print_address_description.constprop.0+0x18/0x130
[ 692.092164] ? find_first_bit+0x28/0x50
[ 692.092185] kasan_report.cold+0x7f/0x111
[ 692.092213] ? static_obj+0x10/0x80
[ 692.092234] ? find_first_bit+0x28/0x50
[ 692.092262] find_first_bit+0x28/0x50
[ 692.092288] adf_msix_isr_ae+0x16e/0x230 [intel_qat]
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a811633f ]
Syzbot hit WARNING in internal_create_group(). The problem was in
too big disk->first_minor.
disk->first_minor is initialized by value, which comes from userspace
and there wasn't any sanity checks about value correctness. It can cause
duplicate creation of sysfs files/links, because disk->first_minor will
be passed to MKDEV() which causes truncation to byte. Since maximum
minor value is 0xff, let's check if first_minor is correct minor number.
NOTE: the root case of the reported warning was in wrong error handling
in register_disk(), but we can avoid passing knowingly wrong values to
sysfs API, because sysfs error messages can confuse users. For example:
user passed 1048576 as index, but sysfs complains about duplicate
creation of /dev/block/43:0. It's not obvious how 1048576 becomes 0.
Log and reproducer for above example can be found on syzkaller bug
report page.
Link: https://syzkaller.appspot.com/bug?id=03c2ae9146416edf811958d5fd7acfab75b143d1
Fixes: b0d9111a2d ("nbd: use an idr to keep track of nbd devices")
Reported-by: syzbot+9937dc42271cd87d4b98@syzkaller.appspotmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be83c3b6e7 ]
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55 ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6f756726e ]
We should set the additional space to 0 in mpi_resize().
So use kcalloc() instead of kmalloc_array().
In lib/mpi/ec.c:
/****************
* Resize the array of A to NLIMBS. the additional space is cleared
* (set to 0) [done by m_realloc()]
*/
int mpi_resize(MPI a, unsigned nlimbs)
Like the comment of kernel's mpi_resize() said, the additional space
need to be set to 0, but when a->d is not NULL, it does not set.
The kernel's mpi lib is from libgcrypt, the mpi resize in libgcrypt
is _gcry_mpi_resize() which set the additional space to 0.
This bug may cause mpi api which use mpi_resize() get wrong result
under the condition of using the additional space without initiation.
If this condition is not met, the bug would not be triggered.
Currently in kernel, rsa, sm2 and dh use mpi lib, and they works well,
so the bug is not triggered in these cases.
add_points_edwards() use the additional space directly, so it will
get a wrong result.
Fixes: cdec9cb516 ("crypto: GnuPG based MPI lib - source files (part 1)")
Signed-off-by: Hongbo Li <herberthbli@tencent.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c1de1de ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-pic32, this is probably not currently an issue but is still good to
fix though.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081727.19491-2-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca4984a7dd ]
The UCLAMP_FLAG_IDLE flag is set on a runqueue when dequeueing the last
uclamp active task (that is, when buckets.tasks reaches 0 for all
buckets) to maintain the last uclamp.max and prevent blocked util from
suddenly becoming visible.
However, there is an asymmetry in how the flag is set and cleared which
can lead to having the flag set whilst there are active tasks on the rq.
Specifically, the flag is cleared in the uclamp_rq_inc() path, which is
called at enqueue time, but set in uclamp_rq_dec_id() which is called
both when dequeueing a task _and_ in the update_uclamp_active() path. As
a result, when both uclamp_rq_{dec,ind}_id() are called from
update_uclamp_active(), the flag ends up being set but not cleared,
hence leaving the runqueue in a broken state.
Fix this by clearing the flag in update_uclamp_active() as well.
Fixes: e496187da7 ("sched/uclamp: Enforce last task's UCLAMP_MAX")
Reported-by: Rick Yiu <rickyiu@google.com>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Qais Yousef <qais.yousef@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lore.kernel.org/r/20210805102154.590709-2-qperret@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9372a82892 ]
Currently allocation and registration of s390dbf debug areas are tied
together. As a result, a debug area cannot be unregistered and
re-registered while any process has an associated debugfs file open.
Fix this by splitting alloc/release from register/unregister.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
