[ Upstream commit 5105a7ffce ]
smb311_decode_neg_context() doesn't properly check against SMB packet
boundaries prior to accessing individual negotiate context entries. This
is due to the length check omitting the eight byte smb2_neg_context
header, as well as incorrect decrementing of len_of_ctxts.
Fixes: 5100d8a3fe ("SMB311: Improve checking of negotiate security contexts")
Reported-by: Volker Lendecke <vl@samba.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8160d3b35 ]
In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.
To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.
Fixes: 69c8c0c0ef ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 775d3c514c ]
set_rtc_noop(), get_rtc_noop() are after booting, therefore their __init
annotation is wrong.
A crash was observed on an x86 platform where CMOS RTC is unused and
disabled via device tree. set_rtc_noop() was invoked from ntp:
sync_hw_clock(), although CONFIG_RTC_SYSTOHC=n, however sync_cmos_clock()
doesn't honour that.
Workqueue: events_power_efficient sync_hw_clock
RIP: 0010:set_rtc_noop
Call Trace:
update_persistent_clock64
sync_hw_clock
Fix this by dropping the __init annotation from set/get_rtc_noop().
Fixes: c311ed6183 ("x86/init: Allow DT configured systems to disable RTC at boot time")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/59f7ceb1-446b-1d3d-0bc8-1f0ee94b1e18@nokia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b277fc793d ]
Platform device helper routines won't update the NUMA distance table
while creating a platform device, even if the device is present on a
NUMA node that doesn't have memory or CPU. This is especially true for
pmem devices. If the target node of the pmem device is not online, we
find the nearest online node to the device and associate the pmem device
with that online node. To find the nearest online node, we should have
the numa distance table updated correctly. Update the distance
information during the device probe.
For a papr scm device on NUMA node 3 distance_lookup_table value for
distance_ref_points_depth = 2 before and after fix is below:
Before fix:
node 3 distance depth 0 - 0
node 3 distance depth 1 - 0
node 4 distance depth 0 - 4
node 4 distance depth 1 - 2
node 5 distance depth 0 - 5
node 5 distance depth 1 - 1
After fix
node 3 distance depth 0 - 3
node 3 distance depth 1 - 1
node 4 distance depth 0 - 4
node 4 distance depth 1 - 2
node 5 distance depth 0 - 5
node 5 distance depth 1 - 1
Without the fix, the nearest numa node to the pmem device (NUMA node 3)
will be picked as 4. After the fix, we get the correct numa node which
is 5.
Fixes: da1115fdbd ("powerpc/nvdimm: Pick nearby online node if the device node is not online")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230404041433.1781804-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa874cdfec ]
Update I2C timing registers based on latest hardware design.
This fix does not break functionality of chips with older design and
existing users will not be affected.
Fixes: 3616936972 ("i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f773f0a331 ]
During the processing of the bgt, if the sync_erase() return -EBUSY
or some other error code in __erase_worker(),schedule_erase() called
again lead to the down_read(ubi->work_sem) hold twice and may get
block by down_write(ubi->work_sem) in ubi_update_fastmap(),
which cause deadlock.
ubi bgt other task
do_work
down_read(&ubi->work_sem) ubi_update_fastmap
erase_worker # Blocked by down_read
__erase_worker down_write(&ubi->work_sem)
schedule_erase
schedule_ubi_work
down_read(&ubi->work_sem)
Fix this by changing input parameter @nested of the schedule_erase() to
'true' to avoid recursively acquiring the down_read(&ubi->work_sem).
Also, fix the incorrect comment about @nested parameter of the
schedule_erase() because when down_write(ubi->work_sem) is held, the
@nested is also need be true.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217093
Fixes: 2e8f08deab ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e020e1b96 upstream.
Following process will make ubi attaching failed since commit
1b42b1a36f ("ubi: ensure that VID header offset ... size"):
ID="0xec,0xa1,0x00,0x15" # 128M 128KB 2KB
modprobe nandsim id_bytes=$ID
flash_eraseall /dev/mtd0
modprobe ubi mtd="0,2048" # set vid_hdr offset as 2048 (one page)
(dmesg):
ubi0 error: ubi_attach_mtd_dev [ubi]: VID header offset 2048 too large.
UBI error: cannot attach mtd0
UBI error: cannot initialize UBI, error -22
Rework original solution, the key point is making sure
'vid_hdr_shift + UBI_VID_HDR_SIZE < ubi->vid_hdr_alsize',
so we should check vid_hdr_shift rather not vid_hdr_offset.
Then, ubi still support (sub)page aligined VID header offset.
Fixes: 1b42b1a36f ("ubi: ensure that VID header offset ... size")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> # v5.10, v4.19
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5cb752b12 upstream.
Beyond reducing code duplication this also avoids scheduling
the mptcp_worker on a closed socket on some edge scenarios.
The addressed issue is actually older than the blamed commit
below, but this fix needs it as a pre-requisite.
Fixes: ba8f48f7a4 ("mptcp: introduce mptcp_schedule_work")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9182a896 upstream.
After a successful cpuset_can_attach() call which increments the
attach_in_progress flag, either cpuset_cancel_attach() or cpuset_attach()
will be called later. In cpuset_attach(), tasks in cpuset_attach_wq,
if present, will be woken up at the end. That is not the case in
cpuset_cancel_attach(). So missed wakeup is possible if the attach
operation is somehow cancelled. Fix that by doing the wakeup in
cpuset_cancel_attach() as well.
Fixes: e44193d39e ("cpuset: let hotplug propagation work wait for task attaching")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 292fd843de upstream.
It was found that commit 7a2127e66a ("cpuset: Call
set_cpus_allowed_ptr() with appropriate mask for task") introduced a bug
that corrupted "cpuset.cpus" of a partition root when it was updated.
It is because the tmp->new_cpus field of the passed tmp parameter
of update_parent_subparts_cpumask() should not be used at all as
it contains important cpumask data that should not be overwritten.
Fix it by using tmp->addmask instead.
Also update update_cpumask() to make sure that trialcs->cpu_allowed
will not be corrupted until it is no longer needed.
Fixes: 7a2127e66a ("cpuset: Call set_cpus_allowed_ptr() with appropriate mask for task")
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcdb1eda53 upstream.
We need to reset forceidle_sum to 0 when reading from root, since the
bstat we accumulate into is stack allocated.
To make this more robust, just replace the existing cputime reset with a
memset of the overall bstat.
Signed-off-by: Josh Don <joshdon@google.com>
Fixes: 1fcf54deb7 ("sched/core: add forced idle accounting for cgroups")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8e22b7a16 upstream.
This reverts commit 3fe97ff3d9 ("scsi: ses: Don't attach if enclosure
has no components") and introduces proper handling of case where there are
no detected secondary components, but primary component (enumerated in
num_enclosures) does exist. That fix was originally proposed by Ding Hui
<dinghui@sangfor.com.cn>.
Completely ignoring devices that have one primary enclosure and no
secondary one results in ses_intf_add() bailing completely
scsi 2:0:0:254: enclosure has no enumerated components
scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such
even on valid configurations with 1 primary and 0 secondary enclosures as
below:
# sg_ses /dev/sg0
3PARdata SES 3321
Supported diagnostic pages:
Supported Diagnostic Pages [sdp] [0x0]
Configuration (SES) [cf] [0x1]
Short Enclosure Status (SES) [ses] [0x8]
# sg_ses -p cf /dev/sg0
3PARdata SES 3321
Configuration diagnostic page:
number of secondary subenclosures: 0
generation code: 0x0
enclosure descriptor list
Subenclosure identifier: 0 [primary]
relative ES process id: 0, number of ES processes: 1
number of type descriptor headers: 1
enclosure logical identifier (hex): 20000002ac02068d
enclosure vendor: 3PARdata product: VV rev: 3321
type descriptor header and text list
Element type: Unspecified, subenclosure id: 0
number of possible elements: 1
The changelog for the original fix follows
=====
We can get a crash when disconnecting the iSCSI session,
the call trace like this:
[ffff00002a00fb70] kfree at ffff00000830e224
[ffff00002a00fba0] ses_intf_remove at ffff000001f200e4
[ffff00002a00fbd0] device_del at ffff0000086b6a98
[ffff00002a00fc50] device_unregister at ffff0000086b6d58
[ffff00002a00fc70] __scsi_remove_device at ffff00000870608c
[ffff00002a00fca0] scsi_remove_device at ffff000008706134
[ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4
[ffff00002a00fd10] scsi_remove_target at ffff0000087064c0
[ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4
[ffff00002a00fdb0] process_one_work at ffff00000810f35c
[ffff00002a00fe00] worker_thread at ffff00000810f648
[ffff00002a00fe70] kthread at ffff000008116e98
In ses_intf_add, components count could be 0, and kcalloc 0 size scomp,
but not saved in edev->component[i].scratch
In this situation, edev->component[0].scratch is an invalid pointer,
when kfree it in ses_intf_remove_enclosure, a crash like above would happen
The call trace also could be other random cases when kfree cannot catch
the invalid pointer
We should not use edev->component[] array when the components count is 0
We also need check index when use edev->component[] array in
ses_enclosure_data_process
=====
Reported-by: Michal Kolar <mich.k@seznam.cz>
Originally-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: stable@vger.kernel.org
Fixes: 3fe97ff3d9 ("scsi: ses: Don't attach if enclosure has no components")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm
Tested-by: Michal Kolar <mich.k@seznam.cz>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 813c2dd786 upstream.
sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.
One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.
# ethtool -m xge0
i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
Cannot get Module EEPROM data: Operation not supported
If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error
# ethtool -m xge0
Cannot get Module EEPROM data: Remote I/O error
Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38518593ec upstream.
During warm reset device->fw_client is set to NULL. If a bus driver is
registered after this NULL setting and before new firmware clients are
enumerated by ISHTP, kernel panic will result in the function
ishtp_cl_bus_match(). This is because of reference to
device->fw_client->props.protocol_name.
ISH firmware after getting successfully loaded, sends a warm reset
notification to remove all clients from the bus and sets
device->fw_client to NULL. Until kernel v5.15, all enabled ISHTP kernel
module drivers were loaded right after any of the first ISHTP device was
registered, regardless of whether it was a matched or an unmatched
device. This resulted in all drivers getting registered much before the
warm reset notification from ISH.
Starting kernel v5.16, this issue got exposed after the change was
introduced to load only bus drivers for the respective matching devices.
In this scenario, cros_ec_ishtp device and cros_ec_ishtp driver are
registered after the warm reset device fw_client NULL setting.
cros_ec_ishtp driver_register() triggers the callback to
ishtp_cl_bus_match() to match ISHTP driver to the device and causes kernel
panic in guid_equal() when dereferencing fw_client NULL pointer to get
protocol_name.
Fixes: f155dfeaa4 ("platform/x86: isthp_eclite: only load for matching devices")
Fixes: facfe0a4fd ("platform/chrome: chros_ec_ishtp: only load for matching devices")
Fixes: 0d0cccc0fd ("HID: intel-ish-hid: hid-client: only load for matching devices")
Fixes: 44e2a58cb8 ("HID: intel-ish-hid: fw-loader: only load for matching devices")
Cc: <stable@vger.kernel.org> # 5.16+
Signed-off-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: Shaunak Saha <shaunak.saha@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7067a4462 upstream.
Confirm that the accessed pneg_ctxt->HashAlgorithms address sits within
the SMB request boundary; deassemble_neg_contexts() only checks that the
eight byte smb2_neg_context header + (client controlled) DataLength are
within the packet boundary, which is insufficient.
Checking for sizeof(struct smb2_preauth_neg_context) is overkill given
that the type currently assumes SMB311_SALT_SIZE bytes of trailing Salt.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c13af03de4 ]
During the development of the maple tree, the strategy of freeing multiple
nodes changed and, in the process, the pivots were reused to store
pointers to dead nodes. To ensure the readers see accurate pivots, the
writers need to mark the nodes as dead and call smp_wmb() to ensure any
readers can identify the node as dead before using the pivot values.
There were two places where the old method of marking the node as dead
without smp_wmb() were being used, which resulted in RCU readers seeing
the wrong pivot value before seeing the node was dead. Fix this race
condition by using mte_set_node_dead() which has the smp_wmb() call to
ensure the race is closed.
Add a WARN_ON() to the ma_free_rcu() call to ensure all nodes being freed
are marked as dead to ensure there are no other call paths besides the two
updated paths.
This is necessary for the RCU mode of the maple tree.
Link: https://lkml.kernel.org/r/20230227173632.3292573-6-surenb@google.com
Fixes: 54a611b605 ("Maple Tree: add new data structure")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c972c1fa ]
The Hyper-V "EnlightenedNptTlb" enlightenment is always enabled when KVM
is running on top of Hyper-V and Hyper-V exposes support for it (which
is always). On AMD CPUs this enlightenment results in ASID invalidations
not flushing TLB entries derived from the NPT. To force the underlying
(L0) hypervisor to rebuild its shadow page tables, an explicit hypercall
is needed.
The original KVM implementation of Hyper-V's "EnlightenedNptTlb" on SVM
only added remote TLB flush hooks. This worked out fine for a while, as
sufficient remote TLB flushes where being issued in KVM to mask the
problem. Since v5.17, changes in the TDP code reduced the number of
flushes and the out-of-sync TLB prevents guests from booting
successfully.
Split svm_flush_tlb_current() into separate callbacks for the 3 cases
(guest/all/current), and issue the required Hyper-V hypercall when a
Hyper-V TLB flush is needed. The most important case where the TLB flush
was missing is when loading a new PGD, which is followed by what is now
svm_flush_tlb_current().
Cc: stable@vger.kernel.org # v5.17+
Fixes: 1e0c7d4075 ("KVM: SVM: hyper-v: Remote TLB flush for SVM")
Link: https://lore.kernel.org/lkml/43980946-7bbf-dcef-7e40-af904c456250@linux.microsoft.com/
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20230324145233.4585-1-jpiotrowski@linux.microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ae7c7bc5 ]
Add a union to provide hv_enlightenments side-by-side with the sw_reserved
bytes that Hyper-V's enlightenments overlay. Casting sw_reserved
everywhere is messy, confusing, and unnecessarily unsafe.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: e5c972c1fa ("KVM: SVM: Flush Hyper-V TLB when required")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 381fc63ac0 ]
Move Hyper-V's VMCB "struct hv_enlightenments" to the svm.h header so
that the struct can be referenced in "struct vmcb_control_area".
Alternatively, a dedicated header for SVM+Hyper-V could be added, a la
x86_64/evmcs.h, but it doesn't appear that Hyper-V will end up needing
a wholesale replacement for the VMCB.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: e5c972c1fa ("KVM: SVM: Flush Hyper-V TLB when required")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 033c56474a ]
[Why]
For engines not supporting soft reset, i.e. VCN, there will be a failed
ib test before mode 1 reset during asic reset. The fences in this case
are never signaled and next time when we try to free the sa_bo, kernel
will hang.
[How]
During pre_asic_reset, driver will clear job fences and afterwards the
fences' refcount will be reduced to 1. For drm_sched_jobs it will be
released in job_free_cb, and for non-sched jobs like ib_test, it's meant
to be released in sa_bo_free but only when the fences are signaled. So
we have to force signal the non_sched bad job's fence during
pre_asic_reset or the clear is not complete.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4eb0b49a0a ]
[why]
when gfx do soft reset, mes will also do reset, if mes is not
resumed when do recover from soft reset, mes is unable to respond
in later sequence
[how]
resume mes when do gfx post soft reset
Signed-off-by: Tong Liu01 <Tong.Liu01@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 923bf981eb ]
Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.
Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b58e3d4311 ]
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit def84ab600 ]
Identify CNS 06h (I/O Command Set Specific Identify Controller data
structure) is supported only on i/o controllers.
But nvme_init_non_mdts_limits() currently invokes this on all
controllers. Correct this by ensuring this is sent to I/O
controllers only.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 813cc94c78 ]
Smatch reports:
drivers/hwmon/xgene-hwmon.c:757 xgene_hwmon_probe() warn:
'ctx->pcc_comm_addr' from ioremap() not released on line: 757.
This is because in drivers/hwmon/xgene-hwmon.c:701 xgene_hwmon_probe(),
ioremap and memremap is not released, which may cause a leak.
To fix this, ioremap and memremap is modified to devm_ioremap and
devm_memremap.
Signed-off-by: Tianyi Jing <jingfelix@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230318143851.2191625-1-jingfelix@hust.edu.cn
[groeck: Fixed formatting and subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03aecb1acb ]
Like the Windows Lenovo Yoga Book X91F/L the Android Lenovo Yoga Book
X90F/L has a portrait 1200x1920 screen used in landscape mode,
add a quirk for this.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301095218.28457-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e7a3bf65d ]
The Acer Aspire 3830TG predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ed213dd64 ]
Another Lenovo convertable which reports a landscape resolution of
1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer
has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc9812a309 ]
After issuing all the messages we can disable the TX_EMPTY interrupts
to avoid handling redundant interrupts. For doing a sinlge bus
detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before
~12000 after ~400).
Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32513d40d9 ]
The commit 11e456cae9 ("selftests/bpf: Fix compilation errors: Assign a value to a constant")
fixed the issue cleanly in bpf-next.
This is an alternative fix in bpf tree to avoid merge conflict between bpf and bpf-next.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
