[ Upstream commit 022152aaeb ]
When it returns an error from sctp_auth_asoc_init_active_key(), the
active_key is actually not updated. The old sh_key will be freeed
while it's still used as active key in asoc. Then an use-after-free
will be triggered when sending patckets, as found by syzbot:
sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
sctp_set_owner_w net/sctp/socket.c:132 [inline]
sctp_sendmsg_to_asoc+0xbd5/0x1a20 net/sctp/socket.c:1863
sctp_sendmsg+0x1053/0x1d50 net/sctp/socket.c:2025
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
This patch is to fix it by not replacing the sh_key when it returns
errors from sctp_auth_asoc_init_active_key() in sctp_auth_set_key().
For sctp_auth_set_active_key(), old active_key_id will be set back
to asoc->active_key_id when the same thing happens.
Fixes: 58acd10092 ("sctp: update active_key for asoc when old key is being replaced")
Reported-by: syzbot+a236dd8e9622ed8954a3@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2568a7e083 ]
The l1oip_cleanup() traverses the l1oip_ilist and calls
release_card() to cleanup module and stack. However,
release_card() calls del_timer() to delete the timers
such as keep_tl and timeout_tl. If the timer handler is
running, the del_timer() will not stop it and result in
UAF bugs. One of the processes is shown below:
(cleanup routine) | (timer handler)
release_card() | l1oip_timeout()
... |
del_timer() | ...
... |
kfree(hc) //FREE |
| hc->timeout_on = 0 //USE
Fix by calling del_timer_sync() in release_card(), which
makes sure the timer handlers have finished before the
resources, such as l1oip and so on, have been deallocated.
What's more, the hc->workq and hc->socket_thread can kick
those timers right back in. We add a bool flag to show
if card is released. Then, check this flag in hc->workq
and hc->socket_thread.
Fixes: 3712b42d4b ("Add layer1 over IP support")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5574d32904 ]
ieee80211_tx_queue_params.aifs is not supposed to be written directly
to the REG_EDCA_*_PARAM registers. Instead process it like the vendor
drivers do. It's kinda hacky but it works.
This change boosts the download speed and makes it more stable.
Tested with RTL8188FU but all the other supported chips should also
benefit.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/038cc03f-3567-77ba-a7bd-c4930e3b2fad@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 116523c8fa ]
Change that introduced the use of __check_timeout did not account for
link types properly, it always assumes ACL_LINK is used thus causing
hdev->acl_last_tx to be used even in case of LE_LINK and then again
uses ACL_LINK with hci_link_tx_to.
To fix this __check_timeout now takes the link type as parameter and
then procedure to use the right last_tx based on the link type and pass
it to hci_link_tx_to.
Fixes: 1b1d29e514 ("Bluetooth: Make use of __check_timeout on hci_sched_le")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: David Beinder <david@beinder.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86067ccfa1 ]
Linux is not the only entity using the BlueField I2C busses so
support a lock mechanism provided by hardware to avoid issues
when multiple entities are trying to access the same bus.
The lock is acquired whenever written explicitely or the lock
register is read. So make sure it is always released at the end
of a successful or failed transaction.
Fixes: b5b5b32081 (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30ea703a38 ]
Include the header containing the prototype of init_ia32_feat_ctl(),
solving the following warning:
$ make W=1 arch/x86/kernel/cpu/feat_ctl.o
arch/x86/kernel/cpu/feat_ctl.c:112:6: warning: no previous prototype for ‘init_ia32_feat_ctl’ [-Wmissing-prototypes]
112 | void init_ia32_feat_ctl(struct cpuinfo_x86 *c)
This warning appeared after commit
5d5103595e ("x86/cpu: Reinitialize IA32_FEAT_CTL MSR on BSP during wakeup")
had moved the function init_ia32_feat_ctl()'s prototype from
arch/x86/kernel/cpu/cpu.h to arch/x86/include/asm/cpu.h.
Note that, before the commit mentioned above, the header include "cpu.h"
(arch/x86/kernel/cpu/cpu.h) was added by commit
0e79ad863d ("x86/cpu: Fix a -Wmissing-prototypes warning for init_ia32_feat_ctl()")
solely to fix init_ia32_feat_ctl()'s missing prototype. So, the header
include "cpu.h" is no longer necessary.
[ bp: Massage commit message. ]
Fixes: 5d5103595e ("x86/cpu: Reinitialize IA32_FEAT_CTL MSR on BSP during wakeup")
Signed-off-by: Luciano Leão <lucianorsleao@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Link: https://lore.kernel.org/r/20220922200053.1357470-1-lucianorsleao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 712f210a45 ]
In preparation for reducing the use of ksize(), record the actual
allocation size for later memcpy(). This avoids copying extra
(uninitialized!) bytes into the patch buffer when the requested
allocation size isn't exactly the size of a kmalloc bucket.
Additionally, fix potential future issues where runtime bounds checking
will notice that the buffer was allocated to a smaller value than
returned by ksize().
Fixes: 757885e94a ("x86, microcode, amd: Early microcode patch loading support for AMD")
Suggested-by: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/lkml/CA+DvKQ+bp7Y7gmaVhacjv9uF6Ar-o4tet872h4Q8RPYPJjcJQA@mail.gmail.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b5ee3357 ]
The number of spatial streams used when acting as a beamformee in VHT
mode are reported by the firmware as 7 (8 sts - 1) both in IPQ6018 and
IPQ8074 which respectively have 2 and 4 sts each. So the firmware should
report 1 (2 - 1) and 3 (4 - 1).
Fix this by checking that the number of VHT beamformee sts reported by
the firmware is not greater than the number of receiving antennas - 1.
The fix is based on the same approach used in this same function for
sanitizing the number of sounding dimensions reported by the firmware.
Without this change, acting as a beamformee in VHT mode is not working
properly.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220616173947.21901-1-jesus.manzano@galgus.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3124d320c2 ]
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1],
for rcu_sync_enter() is called without rcu_sync_init() due to
hci_uart_tty_open() ignoring percpu_init_rwsem() failure.
While we are at it, fix that hci_uart_register_device() ignores
percpu_init_rwsem() failure and hci_uart_unregister_device() does not
call percpu_free_rwsem().
Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f [1]
Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 67d2f8781b ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.")
Fixes: d73e172816 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83c10cc362 ]
The documentation for find_vpid() clearly states:
"Must be called with the tasklist_lock or rcu_read_lock() held."
Presently we do neither for find_vpid() instance in bpf_task_fd_query().
Add proper rcu_read_lock/unlock() to fix the issue.
Fixes: 41bdc4b40e ("bpf: introduce bpf subcommand BPF_TASK_FD_QUERY")
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20220912133855.1218900-1-lee@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e963a19c64 ]
Found by comparing with the vendor driver. Currently this affects
only the RTL8192EU, which is the only gen2 chip with 2 TX paths
supported by this driver. It's unclear what kind of effect the
mistake had in practice, since I don't have any RTL8192EU devices
to test it.
Fixes: e1547c535e ("rtl8xxxu: First stab at adding IQK calibration for 8723bu parts")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/30a59f3a-cfa9-8379-7af0-78a8f4c77cfd@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a37a32583e ]
When trying to finish resolving a struct member, btf_struct_resolve
saves the member type id in a u16 temporary variable. This truncates
the 32 bit type id value if it exceeds UINT16_MAX.
As a result, structs that have members with type ids > UINT16_MAX and
which need resolution will fail with a message like this:
[67414] STRUCT ff_device size=120 vlen=12
effect_owners type_id=67434 bits_offset=960 Member exceeds struct_size
Fix this by changing the type of last_member_type_id to u32.
Fixes: a0791f0df7 ("bpf: fix BTF limits")
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Lorenz Bauer <oss@lmb.io>
Link: https://lore.kernel.org/r/20220910110120.339242-1-oss@lmb.io
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36acf80fc0 ]
Since [1], controller's busy flag isn't set anymore when the
__spi_transfer_message_noqueue() is used instead of the
__spi_pump_transfer_message() logic for spi_sync transfers.
Since the pow2 clock ops were limited to only be available when a
transfer is ongoing (between prepare_transfer_hardware and
unprepare_transfer_hardware callbacks), the only way to track this
down is to check for the controller cur_msg.
[1] ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Fixes: 09992025da ("spi: meson-spicc: add local pow2 clock ops to preserve rate between messages")
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20220908121803.919943-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd3f106677 ]
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10888140f0 ]
Enlarging the size of 'struct btmtk_hci_wmt_cmd' makes it no longer
fit on the kernel stack, as seen from this compiler warning:
drivers/bluetooth/btusb.c:3365:12: error: stack frame size of 1036 bytes in function 'btusb_mtk_hci_wmt_sync' [-Werror,-Wframe-larger-than=]
Change the function to dynamically allocate the buffer instead.
As there are other sleeping functions called from the same location,
using GFP_KERNEL should be fine here, and the runtime overhead should
not matter as this is rarely called.
Unfortunately, I could not figure out why the message size is
increased in the previous patch. Using dynamic allocation means
any size is possible now, but there is still a range check that
limits the total size (including the five-byte header) to 255
bytes, so whatever was intended there is now undone.
Fixes: 48c13301e6 ("Bluetooth: btusb: Fine-tune mt7663 mechanism.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stable-dep-of: fd3f106677 ("Bluetooth: btusb: mediatek: fix WMT failure during runtime suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b75f133fe ]
From 'IEEE Std 802.11-2020 section 11.8.8.4.1':
The mesh channel switch may be triggered by the need to avoid
interference to a detected radar signal, or to reassign mesh STA
channels to ensure the MBSS connectivity.
A 20/40 MHz MBSS may be changed to a 20 MHz MBSS and a 20 MHz
MBSS may be changed to a 20/40 MHz MBSS.
Since the standard allows the change of bandwidth during
the channel switch in mesh, remove the bandwidth check present in
ieee80211_set_csa_beacon.
Fixes: c6da674aff ("{nl,cfg,mac}80211: enable the triggering of CSA frame in mesh")
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Link: https://lore.kernel.org/r/1658903549-21218-1-git-send-email-quic_haric@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32f7eed0c7 ]
The mutex might still be in use until the devm cleanup callback
devm_led_classdev_flash_release() is called. This only happens some time
after lm3601x_remove() completed.
Fixes: e63a744871 ("leds: lm3601x: Convert class registration to device managed")
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f020d9570a ]
When peer delete failed in a disconnect operation, use-after-free
detected by KFENCE in below log. It is because for each vdev_id and
address, it has only one struct ath10k_peer, it is allocated in
ath10k_peer_map_event(). When connected to an AP, it has more than
one HTT_T2H_MSG_TYPE_PEER_MAP reported from firmware, then the
array peer_map of struct ath10k will be set muti-elements to the
same ath10k_peer in ath10k_peer_map_event(). When peer delete failed
in ath10k_sta_state(), the ath10k_peer will be free for the 1st peer
id in array peer_map of struct ath10k, and then use-after-free happened
for the 2nd peer id because they map to the same ath10k_peer.
And clean up all peers in array peer_map for the ath10k_peer, then
user-after-free disappeared
peer map event log:
[ 306.911021] wlan0: authenticate with b0:2a:43:e6:75:0e
[ 306.957187] ath10k_pci 0000:01:00.0: mac vdev 0 peer create b0:2a:43:e6:75:0e (new sta) sta 1 / 32 peer 1 / 33
[ 306.957395] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 306.957404] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 306.986924] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 166
peer unmap event log:
[ 435.715691] wlan0: deauthenticating from b0:2a:43:e6:75:0e by local choice (Reason: 3=DEAUTH_LEAVING)
[ 435.716802] ath10k_pci 0000:01:00.0: mac vdev 0 peer delete b0:2a:43:e6:75:0e sta ffff990e0e9c2b50 (sta gone)
[ 435.717177] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 435.717186] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 435.717193] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 166
use-after-free log:
[21705.888627] wlan0: deauthenticating from d0:76:8f:82:be:75 by local choice (Reason: 3=DEAUTH_LEAVING)
[21713.799910] ath10k_pci 0000:01:00.0: failed to delete peer d0:76:8f:82:be:75 for vdev 0: -110
[21713.799925] ath10k_pci 0000:01:00.0: found sta peer d0:76:8f:82:be:75 (ptr 0000000000000000 id 102) entry on vdev 0 after it was supposedly removed
[21713.799968] ==================================================================
[21713.799991] BUG: KFENCE: use-after-free read in ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.799991]
[21713.799997] Use-after-free read at 0x00000000abe1c75e (in kfence-#69):
[21713.800010] ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.800041] drv_sta_state+0x115/0x677 [mac80211]
[21713.800059] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800076] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800093] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800110] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800137] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800153] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800161] genl_rcv_msg+0x38e/0x3be
[21713.800166] netlink_rcv_skb+0x89/0xf7
[21713.800171] genl_rcv+0x28/0x36
[21713.800176] netlink_unicast+0x179/0x24b
[21713.800181] netlink_sendmsg+0x3a0/0x40e
[21713.800187] sock_sendmsg+0x72/0x76
[21713.800192] ____sys_sendmsg+0x16d/0x1e3
[21713.800196] ___sys_sendmsg+0x95/0xd1
[21713.800200] __sys_sendmsg+0x85/0xbf
[21713.800205] do_syscall_64+0x43/0x55
[21713.800210] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[21713.800213]
[21713.800219] kfence-#69: 0x000000009149b0d5-0x000000004c0697fb, size=1064, cache=kmalloc-2k
[21713.800219]
[21713.800224] allocated by task 13 on cpu 0 at 21705.501373s:
[21713.800241] ath10k_peer_map_event+0x7e/0x154 [ath10k_core]
[21713.800254] ath10k_htt_t2h_msg_handler+0x586/0x1039 [ath10k_core]
[21713.800265] ath10k_htt_htc_t2h_msg_handler+0x12/0x28 [ath10k_core]
[21713.800277] ath10k_htc_rx_completion_handler+0x14c/0x1b5 [ath10k_core]
[21713.800283] ath10k_pci_process_rx_cb+0x195/0x1df [ath10k_pci]
[21713.800294] ath10k_ce_per_engine_service+0x55/0x74 [ath10k_core]
[21713.800305] ath10k_ce_per_engine_service_any+0x76/0x84 [ath10k_core]
[21713.800310] ath10k_pci_napi_poll+0x49/0x144 [ath10k_pci]
[21713.800316] net_rx_action+0xdc/0x361
[21713.800320] __do_softirq+0x163/0x29a
[21713.800325] asm_call_irq_on_stack+0x12/0x20
[21713.800331] do_softirq_own_stack+0x3c/0x48
[21713.800337] __irq_exit_rcu+0x9b/0x9d
[21713.800342] common_interrupt+0xc9/0x14d
[21713.800346] asm_common_interrupt+0x1e/0x40
[21713.800351] ksoftirqd_should_run+0x5/0x16
[21713.800357] smpboot_thread_fn+0x148/0x211
[21713.800362] kthread+0x150/0x15f
[21713.800367] ret_from_fork+0x22/0x30
[21713.800370]
[21713.800374] freed by task 708 on cpu 1 at 21713.799953s:
[21713.800498] ath10k_sta_state+0x2c6/0xb8a [ath10k_core]
[21713.800515] drv_sta_state+0x115/0x677 [mac80211]
[21713.800532] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800548] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800565] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800581] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800598] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800614] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800619] genl_rcv_msg+0x38e/0x3be
[21713.800623] netlink_rcv_skb+0x89/0xf7
[21713.800628] genl_rcv+0x28/0x36
[21713.800632] netlink_unicast+0x179/0x24b
[21713.800637] netlink_sendmsg+0x3a0/0x40e
[21713.800642] sock_sendmsg+0x72/0x76
[21713.800646] ____sys_sendmsg+0x16d/0x1e3
[21713.800651] ___sys_sendmsg+0x95/0xd1
[21713.800655] __sys_sendmsg+0x85/0xbf
[21713.800659] do_syscall_64+0x43/0x55
[21713.800663] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Fixes: d0eeafad11 ("ath10k: Clean up peer when sta goes away.")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220801141930.16794-1-quic_wgong@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd1ef88049 ]
If this memdup_user() call fails, the memory allocated in a previous call
a few lines above should be freed. Otherwise it leaks.
Fixes: 6ee95d1c89 ("nfsd: add support for upcall version 2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14ca1a4690 ]
MT_MEMORY_RO is introduced by commit 598f0a99fa ("ARM: 9210/1:
Mark the FDT_FIXED sections as shareable"), which is a readonly
memory type for FDT area, but there are some different between
ARM_LPAE and non-ARM_LPAE, we need to setup PMD_SECT_AP2 and
L_PMD_SECT_RDONLY for MT_MEMORY_RO when ARM_LAPE enabled.
non-ARM_LPAE 0xff800000-0xffa00000 2M PGD KERNEL ro NX SHD
ARM_LPAE 0xff800000-0xffc00000 4M PMD RW NX SHD
ARM_LPAE+fix 0xff800000-0xffc00000 4M PMD ro NX SHD
Fixes: 598f0a99fa ("ARM: 9210/1: Mark the FDT_FIXED sections as shareable")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ccd19b3ff ]
After ARM supports p4d page tables, the pg_level for note_page()
in walk_pmd() should be 4, not 3, fix it.
Fixes: 84e6ffb2c4 ("arm: add support for folded p4d page tables")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11bec9cba4 ]
In error case in bridge_platform_create after calling
platform_device_add()/platform_device_add_data()/
platform_device_add_resources(), release the failed
'pdev' or it will be leak, call platform_device_put()
to fix this problem.
Besides, 'pdev' is divided into 'pdev_wd' and 'pdev_bd',
use platform_device_unregister() to release sgi_w1
resources when xtalk-bridge registration fails.
Fixes: 5dc76a96e9 ("MIPS: PCI: use information from 1-wire PROM for IOC3 detection")
Signed-off-by: Lin Yujun <linyujun809@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33d7085682 ]
platform_device_add_data() duplicates the memory it is passed. So we can
free some memory to save a few bytes that would remain unused otherwise.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Stable-dep-of: 11bec9cba4 ("MIPS: SGI-IP27: Fix platform-device leak in bridge_platform_create()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abec3d015f ]
Since userfaultfd doesn't implement a write operation, it is more
appropriate to open it read-only.
When userfaultfds are opened read-write like it is now, and such fd is
passed from one process to another, SELinux will check both read and
write permissions for the target process, even though it can't actually
do any write operation on the fd later.
Inspired by the following bug report, which has hit the SELinux scenario
described above:
https://bugzilla.redhat.com/show_bug.cgi?id=1974559
Reported-by: Robert O'Callahan <roc@ocallahan.org>
Fixes: 86039bd3b4 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f09bd695af upstream.
Coverity spotted that we were not initalizing Stbz1 and Stbz2 to
zero in create_sd_buf.
Addresses-Coverity: 1513848 ("Uninitialized scalar variable")
Cc: <stable@vger.kernel.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba9249396 upstream.
As it turns out: while Nvidia does actually have interlacing knobs on their
GPU still pretty much no current GPUs since Volta actually support it.
Trying interlacing on these GPUs will result in NVDisplay being quite
unhappy like so:
nouveau 0000:1f:00.0: disp: chid 0 stat 00004802 reason 4 [INVALID_ARG] mthd 2008 data 00000001 code 00080000
nouveau 0000:1f:00.0: disp: chid 0 stat 10005080 reason 5 [INVALID_STATE] mthd 0200 data 00000001 code 00000001
So let's fix this by following the same behavior Nvidia's driver does and
disable interlacing entirely.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220816180436.156310-1-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d517cdeb90 upstream.
In the greybus audio_helper code, the debugfs file for the dapm has the
potential to be removed and memory will be leaked. There is also the
very real potential for this code to remove ALL debugfs entries from the
system, and it seems like this is what will really happen if this code
ever runs. This all is very wrong as the greybus audio driver did not
create this debugfs file, the sound core did and controls the lifespan
of it.
So remove all of the debugfs logic from the audio_helper code as there's
no way it could be correct. If this really is needed, it can come back
with a fixup for the incorrect usage of the debugfs_lookup() call which
is what caused this to be noticed at all.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220902143715.320500-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eba9799b5a upstream.
Deliberately truncate the exception error code when shoving it into the
VMCS (VM-Entry field for vmcs01 and vmcs02, VM-Exit field for vmcs12).
Intel CPUs are incapable of handling 32-bit error codes and will never
generate an error code with bits 31:16, but userspace can provide an
arbitrary error code via KVM_SET_VCPU_EVENTS. Failure to drop the bits
on exception injection results in failed VM-Entry, as VMX disallows
setting bits 31:16. Setting the bits on VM-Exit would at best confuse
L1, and at worse induce a nested VM-Entry failure, e.g. if L1 decided to
reinject the exception back into L2.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20220830231614.3580124-3-seanjc@google.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
