[ Upstream commit 34d5629d2c ]
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df2b53884a ]
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596bdbcce9 ]
use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a65064abd ]
Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9c52fd17c ]
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58da3b4230 ]
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8e131542b ]
snd_seq_system_client_init() doesn't check the errors returned from
its port creations. Let's do it properly and handle the error paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7417844b63 ]
When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().
After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().
To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.
Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 962341b54b ]
When we have first case to fall through it's not enough to put
single comment there to satisfy compiler. Instead of doing that,
return fall back value directly from default case.
This to avoid following warnings:
drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’:
include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’
dev_warn(ext->dev,
^~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here
case CHT_WC_USBSRC_TYPE_SDP:
^~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 777d8ae56d ]
devm_kcalloc() returns NULL, it never returns error pointers. In the
current code we would return PTR_ERR(NULL) which is success, instead of
returning the -ENOMEM error code.
Fixes: a0a1a1ba30 ("rtc: sysfs: facilitate attribute add to rtc device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 441f61e3aa ]
Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB
I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2
hardware user manuals.
See also commit e9f0089b2d ("arm64: dts: r8a7795: Correct SATA
device size to 2MiB").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33e2641819 ]
get_seconds() and do_gettimeofday() are only used by a few modules now any
more (waiting for the respective patches to get accepted), and they are
among the last holdouts of code that is not y2038 safe in the core kernel.
Move the implementation into the timekeeping32.h header to clean up
the core kernel and isolate the old interfaces further.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13136a47a0 ]
Implement support for the PMC_IMPL_E_33V_PWR register which replaces
PMC_PWR_DET register interface of the SoC generations preceding
Tegra186. Also add the voltage bit offsets to the tegra186_io_pads[]
table and the AO_HV pad.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f128fa41f ]
The "frames" variable is unsigned so the error handling doesn't work
properly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 480f58cdbe ]
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93366b49a3 ]
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09b964afca ]
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1c815f4b2 ]
In case of error, we can dereference uninitialized 'adev'
drivers/soundwire/intel_init.c:154 sdw_intel_acpi_cb()
error: uninitialized symbol 'adev'.
Fix that by not using adev for warn print and make it pr_err.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a306a0e4a5 ]
Deferred messages are async messages used to synchronize
transitions mostly while doing a bank switch on multi links.
On successful transitions these messages are marked complete
and thereby confirming that all the buses performed bank switch
successfully.
So, initialize the completion structure for the same.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58c0f79887 ]
Currently the register offset of the PWM bus gate in Allwinner H6 clock
driver is wrong.
Fix this issue.
Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Rongyi Chen <chenyi@tt-cool.com>
[Icenowy: refactor commit message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd1d395070 ]
When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush
Steps:
In a certain condition, during wifi down below scenario might occur.
ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db878f76b9 ]
DT nodes may have a 'status' property which, if set to anything other
than 'ok' or 'okay', indicates to the OS that the DT node should be
treated as if it was not present. So add that missing logic to the
OP-TEE driver.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1ec080250 ]
After finding a reasonable gain, the function converts the configured
gain to a gain configuration option selector enum max9611_csa_gain.
Make the conversion clearly visible by using an explicit cast. This
also avoids a warning seen with clang:
drivers/iio/adc/max9611.c:292:16: warning: implicit conversion from
enumeration type 'enum max9611_conf_ids' to different enumeration
type 'enum max9611_csa_gain' [-Wenum-conversion]
*csa_gain = gain_selectors[i];
~ ^~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0362f326d8 upstream.
An exiting task might belong to an offline cgroup. In this case an
attempt to grab a cgroup reference from the task can end up with an
infinite loop in hugetlb_cgroup_charge_cgroup(), because neither the
cgroup will become online, neither the task will be migrated to a live
cgroup.
Fix this by switching over to css_tryget(). As css_tryget_online()
can't guarantee that the cgroup won't go offline, in most cases the
check doesn't make sense. In this particular case users of
hugetlb_cgroup_charge_cgroup() are not affected by this change.
A similar problem is described by commit 18fa84a2db ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Link: http://lkml.kernel.org/r/20191106225131.3543616-2-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00d484f354 upstream.
We've encountered a rcu stall in get_mem_cgroup_from_mm():
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 33-....: (21000 ticks this GP) idle=6c6/1/0x4000000000000002 softirq=35441/35441 fqs=5017
(t=21031 jiffies g=324821 q=95837) NMI backtrace for cpu 33
<...>
RIP: 0010:get_mem_cgroup_from_mm+0x2f/0x90
<...>
__memcg_kmem_charge+0x55/0x140
__alloc_pages_nodemask+0x267/0x320
pipe_write+0x1ad/0x400
new_sync_write+0x127/0x1c0
__kernel_write+0x4f/0xf0
dump_emit+0x91/0xc0
writenote+0xa0/0xc0
elf_core_dump+0x11af/0x1430
do_coredump+0xc65/0xee0
get_signal+0x132/0x7c0
do_signal+0x36/0x640
exit_to_usermode_loop+0x61/0xd0
do_syscall_64+0xd4/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The problem is caused by an exiting task which is associated with an
offline memcg. We're iterating over and over in the do {} while
(!css_tryget_online()) loop, but obviously the memcg won't become online
and the exiting task won't be migrated to a live memcg.
Let's fix it by switching from css_tryget_online() to css_tryget().
As css_tryget_online() cannot guarantee that the memcg won't go offline,
the check is usually useless, except some rare cases when for example it
determines if something should be presented to a user.
A similar problem is described by commit 18fa84a2db ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Johannes:
: The bug aside, it doesn't matter whether the cgroup is online for the
: callers. It used to matter when offlining needed to evacuate all charges
: from the memcg, and so needed to prevent new ones from showing up, but we
: don't care now.
Link: http://lkml.kernel.org/r/20191106225131.3543616-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Shakeel Butt <shakeeb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michal Koutn <mkoutny@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a85dfc305a upstream.
Commit d883544515 ("mm: mempolicy: make the behavior consistent when
MPOL_MF_MOVE* and MPOL_MF_STRICT were specified") fixed the return value
of mbind() for a couple of corner cases. But, it altered the errno for
some other cases, for example, mbind() should return -EFAULT when part
or all of the memory range specified by nodemask and maxnode points
outside your accessible address space, or there was an unmapped hole in
the specified memory range specified by addr and len.
Fix this by preserving the errno returned by queue_pages_range(). And,
the pagelist may be not empty even though queue_pages_range() returns
error, put the pages back to LRU since mbind_range() is not called to
really apply the policy so those pages should not be migrated, this is
also the old behavior before the problematic commit.
Link: http://lkml.kernel.org/r/1572454731-3925-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: d883544515 ("mm: mempolicy: make the behavior consistent when MPOL_MF_MOVE* and MPOL_MF_STRICT were specified")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Reported-by: Li Xinhai <lixinhai.lxh@gmail.com>
Reviewed-by: Li Xinhai <lixinhai.lxh@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org> [4.19 and 5.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e7120d79e upstream.
For both PASID-based-Device-TLB Invalidate Descriptor and
Device-TLB Invalidate Descriptor, the Physical Function Source-ID
value is split according to this layout:
PFSID[3:0] is set at offset 12 and PFSID[15:4] is put at offset 52.
Fix the part laid out at offset 52.
Fixes: 0f725561e1 ("iommu/vt-d: Add definitions for PFSID")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: stable@vger.kernel.org # v4.19+
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40a1dcee2d upstream.
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 762c69685f upstream.
We need to get the underlying dentry of parent; sure, absent the races
it is the parent of underlying dentry, but there's nothing to prevent
losing a timeslice to preemtion in the middle of evaluation of
lower_dentry->d_parent->d_inode, having another process move lower_dentry
around and have its (ex)parent not pinned anymore and freed on memory
pressure. Then we regain CPU and try to fetch ->d_inode from memory
that is freed by that point.
dentry->d_parent *is* stable here - it's an argument of ->lookup() and
we are guaranteed that it won't be moved anywhere until we feed it
to d_add/d_splice_alias. So we safely go that way to get to its
underlying dentry.
Cc: stable@vger.kernel.org # since 2009 or so
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e72b9dd6a5 upstream.
lower_dentry can't go from positive to negative (we have it pinned),
but it *can* go from negative to positive. So fetching ->d_inode
into a local variable, doing a blocking allocation, checking that
now ->d_inode is non-NULL and feeding the value we'd fetched
earlier to a function that won't accept NULL is not a good idea.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7574c0db2e upstream.
Many cheap devices use Silead touchscreen controllers. Testing has shown
repeatedly that these touchscreen controllers work fine at 400KHz, but for
unknown reasons do not work properly at 100KHz. This has been seen on
both ARM and x86 devices using totally different i2c controllers.
On some devices the ACPI tables list another device at the same I2C-bus
as only being capable of 100KHz, testing has shown that these other
devices work fine at 400KHz (as can be expected of any recent I2C hw).
This commit makes i2c_acpi_find_bus_speed() always return 400KHz if a
Silead touchscreen controller is present, fixing the touchscreen not
working on devices which ACPI tables' wrongly list another device on the
same bus as only being capable of 100KHz.
Specifically this fixes the touchscreen on the Jumper EZpad 6 m4 not
working.
Reported-by: youling 257 <youling257@gmail.com>
Tested-by: youling 257 <youling257@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: rewording warning a little]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d40d95e7e upstream.
Currently, rmi_f11_attention() and rmi_f12_attention() functions update
the attn_data data pointer and size based on the size of the expected
size of the attention data. However, if the actual valid data in the
attn buffer is less then the expected value then the updated data
pointer will point to memory beyond the end of the attn buffer. Using
the calculated valid_bytes instead will prevent this from happening.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-3-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6aabe1ff1 upstream.
This patch fixes an issue seen on HID touchpads which report finger
positions using RMI4 Function 12. The issue manifests itself as
spurious button presses as described in:
https://www.spinics.net/lists/linux-input/msg58618.html
Commit 24d28e4f12 ("Input: synaptics-rmi4 - convert irq distribution
to irq_domain") switched the RMI4 driver to using an irq_domain to handle
RMI4 function interrupts. Functions with more then one interrupt now have
each interrupt mapped to their own IRQ and IRQ handler. The result of
this change is that the F12 IRQ handler was now getting called twice. Once
for the absolute data interrupt and once for the relative data interrupt.
For HID devices, calling rmi_f12_attention() a second time causes the
attn_data data pointer and size to be set incorrectly. When the touchpad
button is pressed, F30 will generate an interrupt and attempt to read the
F30 data from the invalid attn_data data pointer and report incorrect
button events.
This patch disables the F12 relative interrupt which prevents
rmi_f12_attention() from being called twice.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Simon Wood <simon@mungewell.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6c617102c upstream.
During rename exchange we might have successfully log the new name in the
source root's log tree, in which case we leave our log context (allocated
on stack) in the root's list of log contextes. However we might fail to
log the new name in the destination root, in which case we fallback to
a transaction commit later and never sync the log of the source root,
which causes the source root log context to remain in the list of log
contextes. This later causes invalid memory accesses because the context
was allocated on stack and after rename exchange finishes the stack gets
reused and overwritten for other purposes.
The kernel's linked list corruption detector (CONFIG_DEBUG_LIST=y) can
detect this and report something like the following:
[ 691.489929] ------------[ cut here ]------------
[ 691.489947] list_add corruption. prev->next should be next (ffff88819c944530), but was ffff8881c23f7be4. (prev=ffff8881c23f7a38).
[ 691.489967] WARNING: CPU: 2 PID: 28933 at lib/list_debug.c:28 __list_add_valid+0x95/0xe0
(...)
[ 691.489998] CPU: 2 PID: 28933 Comm: fsstress Not tainted 5.4.0-rc6-btrfs-next-62 #1
[ 691.490001] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
[ 691.490003] RIP: 0010:__list_add_valid+0x95/0xe0
(...)
[ 691.490007] RSP: 0018:ffff8881f0b3faf8 EFLAGS: 00010282
[ 691.490010] RAX: 0000000000000000 RBX: ffff88819c944530 RCX: 0000000000000000
[ 691.490011] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffffa2c497e0
[ 691.490013] RBP: ffff8881f0b3fe68 R08: ffffed103eaa4115 R09: ffffed103eaa4114
[ 691.490015] R10: ffff88819c944000 R11: ffffed103eaa4115 R12: 7fffffffffffffff
[ 691.490016] R13: ffff8881b4035610 R14: ffff8881e7b84728 R15: 1ffff1103e167f7b
[ 691.490019] FS: 00007f4b25ea2e80(0000) GS:ffff8881f5500000(0000) knlGS:0000000000000000
[ 691.490021] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 691.490022] CR2: 00007fffbb2d4eec CR3: 00000001f2a4a004 CR4: 00000000003606e0
[ 691.490025] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 691.490027] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 691.490029] Call Trace:
[ 691.490058] btrfs_log_inode_parent+0x667/0x2730 [btrfs]
[ 691.490083] ? join_transaction+0x24a/0xce0 [btrfs]
[ 691.490107] ? btrfs_end_log_trans+0x80/0x80 [btrfs]
[ 691.490111] ? dget_parent+0xb8/0x460
[ 691.490116] ? lock_downgrade+0x6b0/0x6b0
[ 691.490121] ? rwlock_bug.part.0+0x90/0x90
[ 691.490127] ? do_raw_spin_unlock+0x142/0x220
[ 691.490151] btrfs_log_dentry_safe+0x65/0x90 [btrfs]
[ 691.490172] btrfs_sync_file+0x9f1/0xc00 [btrfs]
[ 691.490195] ? btrfs_file_write_iter+0x1800/0x1800 [btrfs]
[ 691.490198] ? rcu_read_lock_any_held.part.11+0x20/0x20
[ 691.490204] ? __do_sys_newstat+0x88/0xd0
[ 691.490207] ? cp_new_stat+0x5d0/0x5d0
[ 691.490218] ? do_fsync+0x38/0x60
[ 691.490220] do_fsync+0x38/0x60
[ 691.490224] __x64_sys_fdatasync+0x32/0x40
[ 691.490228] do_syscall_64+0x9f/0x540
[ 691.490233] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 691.490235] RIP: 0033:0x7f4b253ad5f0
(...)
[ 691.490239] RSP: 002b:00007fffbb2d6078 EFLAGS: 00000246 ORIG_RAX: 000000000000004b
[ 691.490242] RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f4b253ad5f0
[ 691.490244] RDX: 00007fffbb2d5fe0 RSI: 00007fffbb2d5fe0 RDI: 0000000000000003
[ 691.490245] RBP: 000000000000000d R08: 0000000000000001 R09: 00007fffbb2d608c
[ 691.490247] R10: 00000000000002e8 R11: 0000000000000246 R12: 00000000000001f4
[ 691.490248] R13: 0000000051eb851f R14: 00007fffbb2d6120 R15: 00005635a498bda0
This started happening recently when running some test cases from fstests
like btrfs/004 for example, because support for rename exchange was added
last week to fsstress from fstests.
So fix this by deleting the log context for the source root from the list
if we have logged the new name in the source root.
Reported-by: Su Yue <Damenly_Su@gmx.com>
Fixes: d4682ba03e ("Btrfs: sync log after logging new name")
CC: stable@vger.kernel.org # 4.19+
Tested-by: Su Yue <Damenly_Su@gmx.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 976a68f06b upstream.
The recently introduced unit descriptor validation had some bug for
processing and extension units, it counts a bControlSize byte twice so
it expected a bigger size than it should have been. This seems
resulting in a probe error on a few devices.
Fix the calculation for proper checks of PU and EU.
Fixes: 57f8770620 ("ALSA: usb-audio: More validations of descriptor units")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191114165613.7422-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc9dbfa970 upstream.
The commit 60849562a5 ("ALSA: usb-audio: Fix possible NULL
dereference at create_yamaha_midi_quirk()") added NULL checks in
create_yamaha_midi_quirk(), but there was an overlook. The code
allows one of either injd or outjd is NULL, but the second if check
made returning -ENODEV if any of them is NULL. Fix it in a proper
form.
Fixes: 60849562a5 ("ALSA: usb-audio: Fix possible NULL dereference at create_yamaha_midi_quirk()")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191113111259.24123-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 528699317d upstream.
While output urb's snd_complete_urb() is executing, calling
prepare_outbound_urb() may cause endpoint stopped before
prepare_outbound_urb() returns and result in next urb submitted
to stopped endpoint. usb-audio driver cannot re-use it afterwards as
the urb is still hold by usb stack.
This change checks EP_FLAG_RUNNING flag after prepare_outbound_urb() again
to let snd_complete_urb() know the endpoint already stopped and does not
submit next urb. Below kind of error will be fixed:
[ 213.153103] usb 1-2: timeout: still 1 active urbs on EP #1
[ 213.164121] usb 1-2: cannot submit urb 0, error -16: unknown error
Signed-off-by: Henry Lin <henryl@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191113021420.13377-1-henryl@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
