The variable block_size is being assigned to itself and to
geo->ecc_chunk_size. Clean up the double assignment by removing
the assignment to itself.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Added brcm,brcmnand-v7.3 as possible compatible string to support
brcmnand controller v7.3.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change adds support for brcm NAND v7.3 controller. This controller
uses a newer version of flash_dma engine and change mostly implements
these differences.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Refactored NAND ECC and CMD address configuration code to use helper
functions.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If mtd_oops is in progress, switch to polling during NAND command
completion instead of relying on DMA/interrupts so that the mtd_oops
buffer can be completely written in the assigned NAND partition.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Added a flag to indicate a panic_write so that low level drivers can
use it to take required action where applicable, to ensure oops data
gets written to assigned mtd device.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for Macronix NAND read retry.
Macronix NANDs support specific read operation for data recovery,
which can be enabled with a SET_FEATURE.
Driver checks byte 167 of Vendor Blocks in ONFI parameter page table
to see if this high-reliability function is supported.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NOTICE THAT:
"...we don't know whether we need fallthroughs or breaks here and this
is just a change to avoid having new warnings when switching to
-Wimplicit-fallthrough but this change might be entirely wrong."[1]
See the original thread of discussion here:
https://lore.kernel.org/patchwork/patch/1036251/
So, in preparation to enabling -Wimplicit-fallthrough, this patch silences
the following warnings:
drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ONENAND_IS_DDP(this))
^
drivers/mtd/nand/onenand/onenand_base.c:3284:2: note: here
case ONENAND_DEVICE_DENSITY_2Gb:
^~~~
drivers/mtd/nand/onenand/onenand_base.c:3288:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
this->options |= ONENAND_HAS_UNLOCK_ALL;
drivers/mtd/nand/onenand/onenand_base.c:3290:2: note: here
case ONENAND_DEVICE_DENSITY_1Gb:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Also, notice that this patch doesn't change any functionality. See the
most recent thread of discussion here:
https://lore.kernel.org/patchwork/patch/1077395/
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
[1] https://lore.kernel.org/lkml/20190509085318.34a9d4be@xps13/
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The GigaDevice GD5F1GQ4UFxxG SPI NAND is in current production devices
and, while it has the same logical layout as the E-series devices,
it differs in the SPI interfacing in significant ways.
This support is contingent on previous commits to:
* Add support for two-byte device IDs
* Define macros for page-read ops with three-byte addresses
http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change supports nand-ecc-step-size and nand-ecc-strength fields in
brcmnand DT node to be optional.
see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
If both nand-ecc-strength and nand-ecc-step-size are not specified in
device tree node for NAND, raw NAND layer does detect ECC information by
reading ONFI extended parameter page for parts using ONFI >= 2.1.
In case of non-ONFI NAND parts there could be a nand_id table entry with
ECC information. If there is valid device tree entry for nand-ecc-strength
and nand-ecc-step-size fields it still shall override the detected values.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand-ecc-strength and nand-ecc-step-size can be made optional as
brcmnand driver can support using raw NAND layer detected values.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.
With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.
This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver insists on having the DMA_PREP_INTERRUPT flag set
on all but the first transfer. There's no need to let the user set this
flag, the driver can do it internally whenever it needs it. Drop
handling of this flag from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The gpmi driver aggressively en/disables the clocks between operations
which has significant performance cost. Use runtime PM to get rid of
this bottleneck.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The i.MX23 specific option read code is called right after nand_scan. We
can rely on the NAND core having disabled the chipselect, so there's no
point in restoring the original chip select after NAND operations. Drop
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpmi_ecc_read_page_data uses the page parameter only for a debug printf,
so we can drop the parameter and the debug printf. Moving the oob
delivery from gpmi_ecc_read_page_data to gpmi_ecc_read_page makes the
oob_required parameter unnecessary aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver calls nand_read_page_op without a buffer passed and then
calls chip->legacy.read_buf to read the buffer afterwards which is
the same as passing the buffer nand_read_page_op in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
this->page_buffer_virt and this->payload_virt are always set to the same
value, so drop the former and just use the latter. Same for
this->page_buffer_virt and this->payload_virt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves the whole driver into a single C file. The filename gpmi-lib
implies that it implements library functions, but in fact there are
several cases where functions in gpmi-lib.c call back into functions in
gpmi-nand.c. With this one has to constantly jump between those two
files, so moving it into a single file improves readability, even when
the file gets quite large.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND core has a NAND operation tracing function, but it can only
be used by drivers using the generic option parser from the NAND core.
Export the tracing function as a static inline function in rawnand.h
so that drivers implementing exec_op directly do not have to write their
own operation tracing.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One main goal of the function mtk_nfc_update_ecc_stats is to check
whether sectors are all empty. If they are empty, set these sectors's
data buffer and OOB buffer as 0xff.
But now, the sector OOB buffer pointer is wrongly assigned. We always
do memset from sector 0.
To fix this issue, pass start sector number to make OOB buffer pointer
be properly assigned.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, we only check how many CE# pins are set in device tree.
But it should be necessary to check whether CE# pin setting is
duplicated or if CE# pin index exceeds the maximum CE# number that
controller supports.
So, add validity check to avoid these invalid settings.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, we expand RE# low level time by choosing the max value
between RE# pulse width and RE# access time, and sample data at the
rising edge of RE#.
Then, if RE# access time is bigger than RE# pulse width, the real
read cycle time may be more than NAND SPEC required. This makes
read performance be worse than that expected.
This patch improves data sampling timing by calculating RE# low level
time according to RE# pulse width. If RE# access time is bigger than
RE# pulse width, then delay sampling data timing.
The result of contrast test base on MT2712 evaluat board is as follow.
nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
NFI 2x clock rate: 124800000 HZ.
Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s
Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
At present, the flow of calculating AC timing of read/write cycle in SDR
mode is that:
At first, calculate high hold time which is valid for both read and write
cycle using the max value between tREH_min and tWH_min.
Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max
and tRP_min.
But NAND SPEC shows that Controller should also meet write/read cycle time.
That is write cycle time should be more than tWC_min and read cycle should
be more than tRC_min. Obviously, we do not achieve that now.
This patch corrects the low level time calculation to meet minimum
read/write cycle time required. After getting the high hold time, WE# low
level time will be promised to meet tWP_min and tWC_min requirement,
and RE# low level time will be promised to meet tREA_max, tRP_min and
tRC_min requirement.
Fixes: edfee3619c ("mtd: nand: mtk: add ->setup_data_interface() hook")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The way oobregion->offset is derived for large page NAND parts is
wrong, fixes it.
Fixes: ef5eeea6e9 ("mtd: nand: brcm: switch to mtd_ooblayout_ops")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sometimes the exec_op parser does not choose the optimal pattern if
multiple patterns with optional elements are available. Since the stack
automatically splits operations in multiple exec_op calls, a non-optimal
pattern gets broken up into multiple calls. E.g. an OOB read using the
vf610 driver:
nand: executing subop:
nand: ->CMD [0x00]
nand: ->ADDR [5 cyc: 00 08 ea 94 02]
nand: ->CMD [0x30]
nand: ->WAITRDY [max 200000 ms]
nand: DATA_IN [64 B]
nand: executing subop:
nand: CMD [0x00]
nand: ADDR [5 cyc: 00 08 ea 94 02]
nand: CMD [0x30]
nand: WAITRDY [max 200000 ms]
nand: ->DATA_IN [64 B]
However, the vf610 driver has a pattern which can execute the complete
command in a single go...
This patch makes sure that the longest matching pattern is chosen
instead of the first (potentially only partial) match. With this
change the vf610 reads the OOB in a single exec_op call:
nand: executing subop:
nand: ->CMD [0x00]
nand: ->ADDR [5 cyc: 00 08 c0 1d 00]
nand: ->CMD [0x30]
nand: ->WAITRDY [max 200000 ms]
nand: ->DATA_IN [64 B]
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Vladimir Oltean says:
====================
FDB, VLAN and PTP fixes for SJA1105 DSA
This patchset is an assortment of fixes for the net-next version of the
sja1105 DSA driver:
- Avoid a kernel panic when the driver fails to probe or unregisters
- Finish Arnd Bermann's idea of compiling PTP support as part of the
main DSA driver and not separately
- Better handling of initial port-based VLAN as well as VLANs for
dsa_8021q FDB entries
- Fix address learning for the SJA1105 P/Q/R/S family
- Make static FDB entries persistent across switch resets
- Fix reporting of statically-added FDB entries in 'bridge fdb show'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The first generation switches don't tell us through the dynamic config
interface whether the dumped FDB entries are static or not (the LOCKEDS
bit from P/Q/R/S).
However, now that we're keeping a mirror of all 'bridge fdb' commands in
the static config, this is an opportunity to compare a dumped FDB entry
to the driver's private database. After all, what makes an entry static
is that *we* added it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FDB entry means that "frames that match this VID and DMAC must be
forwarded to this port".
In the case of dsa_8021q however, the VID is not a single one (and
neither two, as my previous patch assumed). The VID can be set either by
the CPU port (1 tx_vid), or by any of the other front-panel port (n-1
rx_vid's).
Fixes: 93647594d8 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.
To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 8456721dd4 ("net: dsa: sja1105: Add support for
configuring address ageing time"), we started to reset the switch rather
often (each time the bridge core changes the ageing time on a switch
port).
The unfortunate reality is that SJA1105 doesn't have any {cold, warm,
whatever} reset mode in which it accepts a new configuration stream
without flushing the FDB. Instead, in its world, the FDB *is* an
optional part of the static configuration.
So we play its game, and do what we also do for VLANs: for each 'bridge
fdb' command, we add the FDB entry through the dynamic interface, and we
append the in-kernel static config memory with info that we're going to
use later, when the next reset command is going to be issued.
The result is that 'bridge fdb' commands are now persistent (dynamically
learned entries are lost, but that's ok).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the commit 1da7382134 ("net: dsa: sja1105: Add FDB
operations for P/Q/R/S series") message, I said that:
At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
It looks like the reason why they were not visible in 'bridge fdb' was
that they were never learned - always flooded.
SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field:
Specify the maximum number of MAC address dynamically learned from
the respective port. It is used to limit the number of learned MAC
addresses per port.
It looks like not providing a value in the static config (aka providing
zeroes) is enough for it to not store the learned addresses in the FDB.
For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This
may be revisited if the situation calls for that - for now I'm happy
that learning works.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1da7382134 ("net: dsa: sja1105: Add FDB operations for
P/Q/R/S series"), these bits were set in the static config, but
apparently they did not do anything. The reason is that the packing
accessors for them were part of a patch I forgot to send.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105 there is no concept of 'default values' per se, everything
needs to be driver-supplied through the static configuration tables.
The issue is that the hardware manual says that 'at least the default
untagging VLAN' is mandatory to be provided through the static config.
But VLAN 0 isn't a very good initial pvid - its use is reserved for
priority-tagged frames, and the layers of the stack that care about
those already make sure that this VLAN is installed, as can be seen in
the message below:
8021q: adding VLAN 0 to HW filter on device swp2
So change the pvid provided through the static configuration to 1, which
matches the bridge core's defaults.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Arnd Bergmann pointed out in commit 78fe8a28fb ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.
So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut says:
====================
net: dsa: microchip: Convert to regmap
This patchset converts KSZ9477 switch driver to regmap.
This was tested with extra patches on KSZ8795. This was also tested
on KSZ9477 on Microchip KSZ9477EVB board, which I now have.
====================
Signed-off-by: Marek Vasut <marex@denx.de>
The regmap config tables are rather similar for various generations of
the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating
those tables without duplication. Note that $regalign parameter is not
used right now, but will be used in KSZ87xx series switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
