Convert MOXA ART SoC bindings to DT schema format using json-schema.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a structure for power parameters including base,
offset, limit and a function to get tx power parameters.
Then, refine flow to get tx power index through the
function.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this macro definition has different values in different chipset,
the current defined macro value is for 8822b. This will cause the
settings of 8822c be incorrect.
Remove RTW_MAX_POWER_INDEX and use max_power_index in struct rtw_chip_info
to make sure the value of different chipset is right.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support more regulatory domains including IC, KCC,
ACMA, CHILE, UKRAINE, and MEXICO. Corresponding tx
power limits for these regulatory domains are added
in tx power limit table. Besides, tx power limits in
some case are also updated to follow RF v20 for better
tx power indexes.
Channel plan mapping table are upgraded to consider
more 2G and 5G channel plans combination cases. It
allow us to identify different situations more accuratly
by channel plan IDs. In addition, mapping table for
country code and channel plan ID and mapping table
for country code and tx power limit are also updated
to follow RF v20. It allow the new enrties in tx power
limit table to be applied correctly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If phy rate is decreased, sub bandwidth may be chosen by RA.
We consider possible power limits and apply the min one;
otherwise, the tx power index may be larger than spec.
And we cross-reference power limits of vht and ht with
20/40M bandwidth in 5G to avoid values are not assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we are loading tx power limit from the power limit table, compare
the world-wide limit with the current limit and choose the lowest power
limit for the world-wide power settings.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx power limit is stored separately by 2G and 5G.
But driver did not get tx power limit from 5G and causes incorrect tx
power. Check if the channel is beyond 2G and get the corresponding tx
power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function names to make them have the same prefix "rtw_phy"
for the tx power setting routines. Only the function names and
corresponding identation are modified.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The type change from (void *) to (struct rtw_dev *) is redundant.
Just pass the right type and compiler can check that for us.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some functions that should be static are unnecessarily exposed, remove
their declaration in header file phy.h.
After resolving their declaration order, they can be declared as static.
So this commit changes nothing except the order and marking them static.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Julian Wiedmann says:
====================
s390/qeth: updates 2019-06-27
please apply another round of qeth updates for net-next.
This completes the conversion of the control path to use dynamically
allocated cmd buffers, along with some fine-tuning for the route
validation fix that recently went into -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cast type currently gets selected in .ndo_start_xmit, and is then
piped through several layers until it's stored into the HW header.
Push the selection down into qeth_l?_fill_header() to (1) reduce the
number of xmit-wide parameters, and (2) merge the two route validation
checks into just one.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As follow-up to commit 0cd6783d3c ("s390/qeth: check dst entry before use"),
consolidate the dst_check() logic into a single helper and add a wrapper
around the cast type selection.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_gro_receive() to pass up all types of packets that a L3 device
may receive.
1) For proper L2 packets received by the IQD sniffer, this is the
obvious thing to do.
2) For af_iucv (which doesn't provide a GRO assist), the GRO code will
transparently fall back to netif_receive_skb(). So there's no need to
special-case this traffic in our code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
De-duplicate the pm callback implementations from the two sub-drivers,
replacing them with core helpers that delegate to the .set_online and
.set_offline callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply some cleanups to qeth_snmp_command() and its callback:
1. when accessing the user data, use the proper struct instead of
hard-coded offsets. Also copy the request data straight into the
allocated cmd, skipping the extra memdup_user() to a tmp buffer.
2. capping the request length is no longer needed, the same check gets
applied at a base level in qeth_alloc_cmd().
3. clean up some duplicated (and misindented) trace statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all cmds are dynamically allocated, the code for static cmd
buffers can go away entirely. Resulting in a nice reduction of
code/data size & complexity, while removing the risk that
qeth_clear_cmd_buffers() releases cmds that are still in-flight.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The base MPC cmds are the last remaining user of the static cmd buffers.
Port them over to use dynamic allocation, and stop backing the write
channel's cmd buffers with pages.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNICC code is somewhat quirky in that it defers the whole cmd setup
to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics
are then passed in via parameter, while others are simply hard-coded.
Split the whole machinery up into the usual format: one helper that
allocates the cmd & fills in the common fields, while all the cmd
originators take care of their sub-cmd type specific work.
This makes it much easier to calculate the cmd's precise length, and
reduces code complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new wrapper that allocates DIAG cmds of the right size, and fills
in the common fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the adapter, assist and bridgeport cmd paths to
dynamic allocation. Most of the work is about re-organizing the cmd
headers, calculating the correct cmd length, and filling in the right
value in the sub-cmd's length field.
Since we now also set the correct length for cmds that are not reflected
by a fixed struct (ie SNMP), we can remove the work-around from
qeth_snmp_command().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For code that uses qeth_send_simple_setassparms_prot(), we currently
can't differentiate whether the cmd should contain (1) no parameter, or
(2) a 4-byte parameter with value 0.
At the moment this doesn't cause any trouble. But when using dynamically
allocated cmds, we need to know whether to allocate & transmit an
additional 4 bytes of zeroes.
So instead of the raw parameter value, pass a parameter pointer
(or NULL) to qeth_send_simple_setassparms_prot().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the usage of the write channel's static cmd buffers,
by dynamically allocating all simple IPA cmds (eg. STARTLAN, SETVMAC).
It also converts the OSN path.
Doing so requires some changes to how we calculate the cmd length.
Currently when building IPA cmds, we're quite generous in how much data
we send down to the device (basically the size of the biggest cmd we
know). This is no real concern at the moment, since the static cmd
buffers are backed with zeroed pages. But for dynamic allocations, the
exact length matters. So this patch also adds the needed length
calculations to each cmd path.
Commands that have multiple subtypes (eg. SETADP) of differing length
will be converted with follow-up patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are common steps when releasing an accepted or unaccepted socket.
Move this code into a common routine.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
net: ipv4: fix circular-list infinite loop
Tariq and Ran reported a regression caused by net-next commit
2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list").
This happens when net.ipv4.conf.$dev.promote_secondaries sysctl is
enabled -- we can arrange for ifa->next to point at ifa, so next
process that tries to walk the list loops forever.
Fix this and extend rtnetlink.sh with a small test case for this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This exercises the 'promote_secondaries' code path.
Without previous fix, this triggers infinite loop/soft lockup:
ifconfig process spinning at 100%, never to return.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
secondary address promotion causes infinite loop -- it arranges
for ifa->ifa_next to point back to itself.
Problem is that 'prev_prom' and 'last_prim' might point at the same entry,
so 'last_sec' pointer must be obtained after prev_prom->next update.
Fixes: 2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list")
Reported-by: Ran Rozenstein <ranro@mellanox.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
main_proc_lock and int_lock (in mwifiex_adapter) are the only spinlocks
used in hardirq contexts. The rest are only in task or softirq contexts.
Convert every other lock from *_irq{save,restore}() variants to _bh()
variants.
This is a mechanical transformation of all spinlock usage in mwifiex
using the following:
Step 1:
I ran this nasty sed script:
sed -i -E '/spin_lock_irqsave|spin_unlock_irqrestore/ {
/main_proc_lock|int_lock/! {
s:(spin_(un|)lock)_irq(save|restore):\1_bh: ;
# Join broken lines.
:a /;$/! {
N;
s/\s*\n\s*//;
ba
}
/,.*\);$/ s:,.*\):\):
}
}' drivers/net/wireless/marvell/mwifiex/*
Step 2:
Manually delete the flags / ra_list_flags args from:
mwifiex_send_single_packet()
mwifiex_11n_aggregate_pkt()
mwifiex_send_processed_packet()
which are now unused.
Step 3:
Apply this semantic patch (coccinelle) to remove the unused 'flags'
variables:
// <smpl>
@@
type T;
identifier i;
@@
(
extern T i;
|
- T i;
... when != i
)
// </smpl>
(Usage is something like this:
make coccicheck COCCI=./patch.cocci MODE=patch M=drivers/net/wireless/marvell/mwifiex/
although this skips *.h files for some reasons, so I had to massage
stuff.)
Testing: I've played with a variety of stress tests, including download
stress tests on the same APs which caught regressions with commit
5188d5453b ("mwifiex: restructure rx_reorder_tbl_lock usage"). I've
primarily tested on Marvell 8997 / PCIe, although I've given 8897 / SDIO
a quick spin as well.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_11n_scan_and_dispatch() and
mwifiex_11n_dispatch_pkt_until_start_win() share similar patterns, where
they perform a few different actions on the same table, using the same
lock, but non-atomically. There have been other attempts to clean up
this sort of behavior, but they have had problems (incomplete;
introducing new deadlocks).
We can improve these functions' atomicity by queueing up our RX packets
in a list, to dispatch at the end of the function. This avoids problems
of another operation modifying the table in between our dispatch and
rotation operations.
This was inspired by investigations around this:
http://lkml.kernel.org/linux-wireless/20181130175957.167031-1-briannorris@chromium.org
Subject: [4.20 PATCH] Revert "mwifiex: restructure rx_reorder_tbl_lock usage"
While the original (now-reverted) patch had good intentions in
restructuring some of the locking patterns in this driver, it missed an
important detail: we cannot defer to softirq contexts while already in
an atomic context. We can help avoid this sort of problem by separating
the two steps of:
(1) iterating / clearing the mwifiex reordering table
(2) dispatching received packets to upper layers
This makes it much harder to make lock recursion mistakes, as these
two steps no longer need to hold the same locks.
Testing: I've played with a variety of stress tests, including download
stress tests on the same APs which caught regressions with commit
5188d5453b ("mwifiex: restructure rx_reorder_tbl_lock usage"). I've
primarily tested on Marvell 8997 / PCIe, although I've given 8897 / SDIO
a quick spin as well.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part
Fixes: f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip.
For chained irqchips this is a pretty straight-forward
conversion.
Take this opportunity to add a local dev pointer and
use devm_gpiochip_add() so we can get rid of the remove()
callback altogether.
Cc: linux-mips@linux-mips.org
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When parsing an ethtool_rx_flow_spec, users can specify an ethernet flow
which could contain matches based on the ethernet header, such as the
MAC address, the VLAN tag or the ethertype.
ETHER_FLOW uses the src and dst ethernet addresses, along with the
ethertype as keys. Matches based on the vlan tag are also possible, but
they are specified using the special FLOW_EXT flag.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Pablo Neira Ayuso <pablo@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ceph_mdsc_build_path is handed a positive dentry, it will return a
zero-length path string with the base set to that dentry. This is not
what we want. Always include at least one path component in the string.
ceph_mdsc_build_path has behaved this way for a long time but it didn't
matter until recent d_name handling rework.
Fixes: 964fff7491 ("ceph: use ceph_mdsc_build_path instead of clone_dentry_name")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The function tegra_gpio_debuginit() just calls debugfs_create_file()
and given that there is already a stub function implemented for
debugfs_create_file() when CONFIG_DEBUG_FS is not enabled, there is
no need for the function tegra_gpio_debuginit() and so remove it.
Finally, use a space and not a tab between the #ifdef and
CONFIG_DEBUG_FS.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a couple of spelling mistakes in dm_error messages and
a comment. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In XGMI configuration, more than one asic can be reset at same time,
kfd is able to handle this and no need to trigger the warning
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Returning -EAGAIN prevents ttm_bo_mem_space from trying alternate
placements and can lead to live-locks in amdgpu_cs, retrying
indefinitely and never succeeding.
Fixes: d367bd2a5e ("drm/ttm: fix busy memory to fail other user v10")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the trylock on the hmm->mirrors_sem fails the function will return
without decrementing the notifiers that were previously incremented. Since
the caller will not call invalidate_range_end() on EAGAIN this will result
in notifiers becoming permanently incremented and deadlock.
If the sync_cpu_device_pagetables() required blocking the function will
not return EAGAIN even though the device continues to touch the
pages. This is a violation of the mmu notifier contract.
Switch, and rename, the ranges_lock to a spin lock so we can reliably
obtain it without blocking during error unwind.
The error unwind is necessary since the notifiers count must be held
incremented across the call to sync_cpu_device_pagetables() as we cannot
allow the range to become marked valid by a parallel
invalidate_start/end() pair while doing sync_cpu_device_pagetables().
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Philip Yang <Philip.Yang@amd.com>
Lets add the MODULE_TABLE and platform id_table entries so that
the SPE driver can attach to the ACPI platform device created by
the core pmu code.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
ACPI 6.3 adds additional fields to the MADT GICC
structure to describe SPE PPI's. We pick these out
of the cached reference to the madt_gicc structure
similarly to the core PMU code. We then create a platform
device referring to the IRQ and let the user/module loader
decide whether to load the SPE driver.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
