[ Upstream commit 200dccd07d ]
Lexar NM610 reports bogus eui64 values that appear to be the same across
all drives. Quirk them out so they are not marked as "non globally unique"
duplicates.
Signed-off-by: Shyamin Ayesh <me@shyamin.com>
[patch formatting]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: 74391b3e69 ("nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b961bce50 ]
When ZHITAI TiPro7000 SSDs entered deepest power state(ps4)
it has the same APST sleep problem as Kingston A2000.
by chance the system crashes and displays the same dmesg info:
https://bugzilla.kernel.org/show_bug.cgi?id=195039#c65
As the Archlinux wiki suggest (enlat + exlat) < 25000 is fine
and my testing shows no system crashes ever since.
Therefore disabling the deepest power state will fix the APST sleep issue.
https://wiki.archlinux.org/title/Solid_state_drive/NVMe
This is the APST data from 'nvme id-ctrl /dev/nvme1'
NVME Identify Controller:
vid : 0x1e49
ssvid : 0x1e49
sn : [...]
mn : ZHITAI TiPro7000 1TB
fr : ZTA32F3Y
[...]
ps 0 : mp:3.50W operational enlat:5 exlat:5 rrt:0 rrl:0
rwt:0 rwl:0 idle_power:- active_power:-
ps 1 : mp:3.30W operational enlat:50 exlat:100 rrt:1 rrl:1
rwt:1 rwl:1 idle_power:- active_power:-
ps 2 : mp:2.80W operational enlat:50 exlat:200 rrt:2 rrl:2
rwt:2 rwl:2 idle_power:- active_power:-
ps 3 : mp:0.1500W non-operational enlat:500 exlat:5000 rrt:3 rrl:3
rwt:3 rwl:3 idle_power:- active_power:-
ps 4 : mp:0.0200W non-operational enlat:2000 exlat:60000 rrt:4 rrl:4
rwt:4 rwl:4 idle_power:- active_power:-
Signed-off-by: Ning Wang <ningwang35@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: 74391b3e69 ("nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3765fad508 ]
ADATA XPG GAMMIX S50 drives report bogus eui64 values that appear to
be the same across drives in one system. Quirk them out so they are
not marked as "non globally unique" duplicates.
Signed-off-by: Stefan Reiter <stefan@pimaker.at>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: 74391b3e69 ("nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8160d3b35 ]
In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.
To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.
Fixes: 69c8c0c0ef ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 775d3c514c ]
set_rtc_noop(), get_rtc_noop() are after booting, therefore their __init
annotation is wrong.
A crash was observed on an x86 platform where CMOS RTC is unused and
disabled via device tree. set_rtc_noop() was invoked from ntp:
sync_hw_clock(), although CONFIG_RTC_SYSTOHC=n, however sync_cmos_clock()
doesn't honour that.
Workqueue: events_power_efficient sync_hw_clock
RIP: 0010:set_rtc_noop
Call Trace:
update_persistent_clock64
sync_hw_clock
Fix this by dropping the __init annotation from set/get_rtc_noop().
Fixes: c311ed6183 ("x86/init: Allow DT configured systems to disable RTC at boot time")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/59f7ceb1-446b-1d3d-0bc8-1f0ee94b1e18@nokia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b277fc793d ]
Platform device helper routines won't update the NUMA distance table
while creating a platform device, even if the device is present on a
NUMA node that doesn't have memory or CPU. This is especially true for
pmem devices. If the target node of the pmem device is not online, we
find the nearest online node to the device and associate the pmem device
with that online node. To find the nearest online node, we should have
the numa distance table updated correctly. Update the distance
information during the device probe.
For a papr scm device on NUMA node 3 distance_lookup_table value for
distance_ref_points_depth = 2 before and after fix is below:
Before fix:
node 3 distance depth 0 - 0
node 3 distance depth 1 - 0
node 4 distance depth 0 - 4
node 4 distance depth 1 - 2
node 5 distance depth 0 - 5
node 5 distance depth 1 - 1
After fix
node 3 distance depth 0 - 3
node 3 distance depth 1 - 1
node 4 distance depth 0 - 4
node 4 distance depth 1 - 2
node 5 distance depth 0 - 5
node 5 distance depth 1 - 1
Without the fix, the nearest numa node to the pmem device (NUMA node 3)
will be picked as 4. After the fix, we get the correct numa node which
is 5.
Fixes: da1115fdbd ("powerpc/nvdimm: Pick nearby online node if the device node is not online")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230404041433.1781804-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f773f0a331 ]
During the processing of the bgt, if the sync_erase() return -EBUSY
or some other error code in __erase_worker(),schedule_erase() called
again lead to the down_read(ubi->work_sem) hold twice and may get
block by down_write(ubi->work_sem) in ubi_update_fastmap(),
which cause deadlock.
ubi bgt other task
do_work
down_read(&ubi->work_sem) ubi_update_fastmap
erase_worker # Blocked by down_read
__erase_worker down_write(&ubi->work_sem)
schedule_erase
schedule_ubi_work
down_read(&ubi->work_sem)
Fix this by changing input parameter @nested of the schedule_erase() to
'true' to avoid recursively acquiring the down_read(&ubi->work_sem).
Also, fix the incorrect comment about @nested parameter of the
schedule_erase() because when down_write(ubi->work_sem) is held, the
@nested is also need be true.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217093
Fixes: 2e8f08deab ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e020e1b96 upstream.
Following process will make ubi attaching failed since commit
1b42b1a36f ("ubi: ensure that VID header offset ... size"):
ID="0xec,0xa1,0x00,0x15" # 128M 128KB 2KB
modprobe nandsim id_bytes=$ID
flash_eraseall /dev/mtd0
modprobe ubi mtd="0,2048" # set vid_hdr offset as 2048 (one page)
(dmesg):
ubi0 error: ubi_attach_mtd_dev [ubi]: VID header offset 2048 too large.
UBI error: cannot attach mtd0
UBI error: cannot initialize UBI, error -22
Rework original solution, the key point is making sure
'vid_hdr_shift + UBI_VID_HDR_SIZE < ubi->vid_hdr_alsize',
so we should check vid_hdr_shift rather not vid_hdr_offset.
Then, ubi still support (sub)page aligined VID header offset.
Fixes: 1b42b1a36f ("ubi: ensure that VID header offset ... size")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> # v5.10, v4.19
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5cb752b12 upstream.
Beyond reducing code duplication this also avoids scheduling
the mptcp_worker on a closed socket on some edge scenarios.
The addressed issue is actually older than the blamed commit
below, but this fix needs it as a pre-requisite.
Fixes: ba8f48f7a4 ("mptcp: introduce mptcp_schedule_work")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9182a896 upstream.
After a successful cpuset_can_attach() call which increments the
attach_in_progress flag, either cpuset_cancel_attach() or cpuset_attach()
will be called later. In cpuset_attach(), tasks in cpuset_attach_wq,
if present, will be woken up at the end. That is not the case in
cpuset_cancel_attach(). So missed wakeup is possible if the attach
operation is somehow cancelled. Fix that by doing the wakeup in
cpuset_cancel_attach() as well.
Fixes: e44193d39e ("cpuset: let hotplug propagation work wait for task attaching")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8e22b7a16 upstream.
This reverts commit 3fe97ff3d9 ("scsi: ses: Don't attach if enclosure
has no components") and introduces proper handling of case where there are
no detected secondary components, but primary component (enumerated in
num_enclosures) does exist. That fix was originally proposed by Ding Hui
<dinghui@sangfor.com.cn>.
Completely ignoring devices that have one primary enclosure and no
secondary one results in ses_intf_add() bailing completely
scsi 2:0:0:254: enclosure has no enumerated components
scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such
even on valid configurations with 1 primary and 0 secondary enclosures as
below:
# sg_ses /dev/sg0
3PARdata SES 3321
Supported diagnostic pages:
Supported Diagnostic Pages [sdp] [0x0]
Configuration (SES) [cf] [0x1]
Short Enclosure Status (SES) [ses] [0x8]
# sg_ses -p cf /dev/sg0
3PARdata SES 3321
Configuration diagnostic page:
number of secondary subenclosures: 0
generation code: 0x0
enclosure descriptor list
Subenclosure identifier: 0 [primary]
relative ES process id: 0, number of ES processes: 1
number of type descriptor headers: 1
enclosure logical identifier (hex): 20000002ac02068d
enclosure vendor: 3PARdata product: VV rev: 3321
type descriptor header and text list
Element type: Unspecified, subenclosure id: 0
number of possible elements: 1
The changelog for the original fix follows
=====
We can get a crash when disconnecting the iSCSI session,
the call trace like this:
[ffff00002a00fb70] kfree at ffff00000830e224
[ffff00002a00fba0] ses_intf_remove at ffff000001f200e4
[ffff00002a00fbd0] device_del at ffff0000086b6a98
[ffff00002a00fc50] device_unregister at ffff0000086b6d58
[ffff00002a00fc70] __scsi_remove_device at ffff00000870608c
[ffff00002a00fca0] scsi_remove_device at ffff000008706134
[ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4
[ffff00002a00fd10] scsi_remove_target at ffff0000087064c0
[ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4
[ffff00002a00fdb0] process_one_work at ffff00000810f35c
[ffff00002a00fe00] worker_thread at ffff00000810f648
[ffff00002a00fe70] kthread at ffff000008116e98
In ses_intf_add, components count could be 0, and kcalloc 0 size scomp,
but not saved in edev->component[i].scratch
In this situation, edev->component[0].scratch is an invalid pointer,
when kfree it in ses_intf_remove_enclosure, a crash like above would happen
The call trace also could be other random cases when kfree cannot catch
the invalid pointer
We should not use edev->component[] array when the components count is 0
We also need check index when use edev->component[] array in
ses_enclosure_data_process
=====
Reported-by: Michal Kolar <mich.k@seznam.cz>
Originally-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: stable@vger.kernel.org
Fixes: 3fe97ff3d9 ("scsi: ses: Don't attach if enclosure has no components")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm
Tested-by: Michal Kolar <mich.k@seznam.cz>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 813c2dd786 upstream.
sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.
One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.
# ethtool -m xge0
i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
Cannot get Module EEPROM data: Operation not supported
If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error
# ethtool -m xge0
Cannot get Module EEPROM data: Remote I/O error
Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00f4bc5184 ]
Signal 16 and higher represent the device's Index lines. The
priv->preset_enable array holds the device configuration for these Index
lines. The preset_enable configuration is active low on the device, so
invert the conditional check in quad8_action_read() to properly handle
the logical state of preset_enable.
Fixes: f1d8a071d4 ("counter: 104-quad-8: Add Generic Counter interface support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230316203426.224745-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaec1a0f76 ]
This is a reimplementation of the Generic Counter driver interface.
There are no modifications to the Counter subsystem userspace interface,
so existing userspace applications should continue to run seamlessly.
The purpose of this patch is to internalize the sysfs interface code
among the various counter drivers into a shared module. Counter drivers
pass and take data natively (i.e. u8, u64, etc.) and the shared counter
module handles the translation between the sysfs interface and the
device drivers. This guarantees a standard userspace interface for all
counter drivers, and helps generalize the Generic Counter driver ABI in
order to support the Generic Counter chrdev interface (introduced in a
subsequent patch) without significant changes to the existing counter
drivers.
Note, Counter device registration is the same as before: drivers
populate a struct counter_device with components and callbacks, then
pass the structure to the devm_counter_register function. However,
what's different now is how the Counter subsystem code handles this
registration internally.
Whereas before callbacks would interact directly with sysfs data, this
interaction is now abstracted and instead callbacks interact with native
C data types. The counter_comp structure forms the basis for Counter
extensions.
The counter-sysfs.c file contains the code to parse through the
counter_device structure and register the requested components and
extensions. Attributes are created and populated based on type, with
respective translation functions to handle the mapping between sysfs and
the counter driver callbacks.
The translation performed for each attribute is straightforward: the
attribute type and data is parsed from the counter_attribute structure,
the respective counter driver read/write callback is called, and sysfs
I/O is handled before or after the driver read/write function is called.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> # for stm32
Link: https://lore.kernel.org/r/c68b4a1ffb195c1a2f65e8dd5ad7b7c14e79c6ef.1630031207.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 00f4bc5184 ("counter: 104-quad-8: Fix Synapse action reported for Index signals")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b58e3d4311 ]
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03aecb1acb ]
Like the Windows Lenovo Yoga Book X91F/L the Android Lenovo Yoga Book
X90F/L has a portrait 1200x1920 screen used in landscape mode,
add a quirk for this.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301095218.28457-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ed213dd64 ]
Another Lenovo convertable which reports a landscape resolution of
1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer
has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc9812a309 ]
After issuing all the messages we can disable the TX_EMPTY interrupts
to avoid handling redundant interrupts. For doing a sinlge bus
detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before
~12000 after ~400).
Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14c76b2e75 ]
This doesn't need to be printed every second as an error:
...
<3>[17438.628385] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17439.634176] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17440.640298] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
...
Reduce priority from ERROR to DEBUG.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceac10c83b ]
__copy_to_user_memcpy() and __clear_user_memset() had been calling
memcpy() and memset() respectively, leading to false-positive KASAN
reports when starting userspace:
[ 10.707901] Run /init as init process
[ 10.731892] process '/bin/busybox' started with executable stack
[ 10.745234] ==================================================================
[ 10.745796] BUG: KASAN: user-memory-access in __clear_user_memset+0x258/0x3ac
[ 10.747260] Write of size 2687 at addr 000de581 by task init/1
Use __memcpy() and __memset() instead to allow userspace access, which
is of course the intent of these functions.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 872aec4b5f ]
btf_dump APIs emit unnecessary tabs when emitting struct/union
definition that fits on the single line. Before this patch we'd get:
struct blah {<tab>};
This patch fixes this and makes sure that we get more natural:
struct blah {};
Fixes: 44a726c3f2 ("bpftool: Print newline before '}' for struct with padding only fields")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221212211505.558851-2-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0646dc31ca ]
Commit 1effe8ca4e ("skbuff: fix coalescing for page_pool fragment
recycling") allowed coalescing to proceed with non page pool page and page
pool page when @from is cloned, i.e.
to->pp_recycle --> false
from->pp_recycle --> true
skb_cloned(from) --> true
However, it actually requires skb_cloned(@from) to hold true until
coalescing finishes in this situation. If the other cloned SKB is
released while the merging is in process, from_shinfo->nr_frags will be
set to 0 toward the end of the function, causing the increment of frag
page _refcount to be unexpectedly skipped resulting in inconsistent
reference counts. Later when SKB(@to) is released, it frees the page
directly even though the page pool page is still in use, leading to
use-after-free or double-free errors. So it should be prohibited.
The double-free error message below prompted us to investigate:
BUG: Bad page state in process swapper/1 pfn:0e0d1
page:00000000c6548b28 refcount:-1 mapcount:0 mapping:0000000000000000
index:0x2 pfn:0xe0d1
flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
raw: 000fffffc0000000 0000000000000000 ffffffff00000101 0000000000000000
raw: 0000000000000002 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 6.2.0+
Call Trace:
<IRQ>
dump_stack_lvl+0x32/0x50
bad_page+0x69/0xf0
free_pcp_prepare+0x260/0x2f0
free_unref_page+0x20/0x1c0
skb_release_data+0x10b/0x1a0
napi_consume_skb+0x56/0x150
net_rx_action+0xf0/0x350
? __napi_schedule+0x79/0x90
__do_softirq+0xc8/0x2b1
__irq_exit_rcu+0xb9/0xf0
common_interrupt+0x82/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0xb/0x20
Fixes: 53e0961da1 ("page_pool: add frag page recycling support in page pool")
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230413090353.14448-1-liangchen.linux@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c5950fc6f ]
lena wang reported an issue caused by udpv6_sendmsg()
mangling msg->msg_name and msg->msg_namelen, which
are later read from ____sys_sendmsg() :
/*
* If this is sendmmsg() and sending to current destination address was
* successful, remember it.
*/
if (used_address && err >= 0) {
used_address->name_len = msg_sys->msg_namelen;
if (msg_sys->msg_name)
memcpy(&used_address->name, msg_sys->msg_name,
used_address->name_len);
}
udpv6_sendmsg() wants to pretend the remote address family
is AF_INET in order to call udp_sendmsg().
A fix would be to modify the address in-place, instead
of using a local variable, but this could have other side effects.
Instead, restore initial values before we return from udpv6_sendmsg().
Fixes: c71d8ebe7a ("net: Fix security_socket_sendmsg() bypass problem.")
Reported-by: lena wang <lena.wang@mediatek.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230412130308.1202254-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32832a2caf ]
Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.
This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip.
Fixes: 0fc2ea922c ("sctp: implement validate_ftsn for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/2a71bffcd80b4f2c61fac6d344bb2f11c8fd74f7.1681155810.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7573099e10 ]
Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7e2cf4feba ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
