commit 7f88a5ac39 upstream.
Commit 17539f2f4f ("usb: musb: fix enumeration after resume") replaced
musb_start() in musb_resume() to not override softconnect bit, but it
doesn't restart the session for host port which was done in musb_start().
The session could be disabled in musb_suspend(), which leads the host
port doesn't stay in host mode.
So let's start the session specifically for host port in musb_resume().
Fixes: 17539f2f4f ("usb: musb: fix enumeration after resume")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200525025049.3400-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18dfb53263 upstream.
The bytes returned by the i2c reading need to be swapped
unconditionally. Otherwise, on be16 platforms, an incorrect value will be
returned.
Taking the slow path via next merge window as its been around a while
and we have a patch set dependent on this which would be held up.
Fixes: 62a1efb9f8 ("iio: add vcnl4000 combined ALS and proximity sensor")
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 986c1748c8 upstream.
usb_wwan_indat_callback() shouldn't resubmit rx urb if the previous urb
status is a fatal error. Or the usb controller would keep processing the
new urbs then run into interrupt storm, and has no chance to recover.
Fixes: 6c1ee66a0b ("USB-Serial: Fix error handling of usb_wwan")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3429444abd upstream.
Add support for Dell Wireless 5816e Download Mode (AKA boot & hold mode /
QDL download mode) to drivers/usb/serial/qcserial.c
This is required to update device firmware.
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dd912f826 ]
Syzkaller again found a path to a kernel crash through bad gso input:
a packet with gso size exceeding len.
These packets are dropped in tcp_gso_segment and udp[46]_ufo_fragment.
But they may affect gso size calculations earlier in the path.
Now that we have thlen as of commit 9274124f02 ("net: stricter
validation of untrusted gso packets"), check gso_size at entry too.
Fixes: bfd5f4a3d6 ("packet: Add GSO/csum offload support.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e0afbdfd1 ]
The accept(2) is an "input" socket interface, so we should use
SO_RCVTIMEO instead of SO_SNDTIMEO to set the timeout.
So this patch replace sock_sndtimeo() with sock_rcvtimeo() to
use the right timeout in the vsock_accept().
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3decabdc71 ]
st21nfca_tm_send_atr_res() misses to call kfree_skb() in an error path.
Add the missed function call to fix it.
Fixes: 1892bf844e ("NFC: st21nfca: Adding P2P support to st21nfca in Initiator & Target mode")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d9a81a2252 ]
syzbot was able to trigger a crash after using an ISDN socket
and fool l2tp.
Fix this by making sure the UDP socket is of the proper family.
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x465/0x540 net/ipv4/udp_tunnel.c:78
Write of size 1 at addr ffff88808ed0c590 by task syz-executor.5/3018
CPU: 0 PID: 3018 Comm: syz-executor.5 Not tainted 5.7.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd3/0x413 mm/kasan/report.c:382
__kasan_report.cold+0x20/0x38 mm/kasan/report.c:511
kasan_report+0x33/0x50 mm/kasan/common.c:625
setup_udp_tunnel_sock+0x465/0x540 net/ipv4/udp_tunnel.c:78
l2tp_tunnel_register+0xb15/0xdd0 net/l2tp/l2tp_core.c:1523
l2tp_nl_cmd_tunnel_create+0x4b2/0xa60 net/l2tp/l2tp_netlink.c:249
genl_family_rcv_msg_doit net/netlink/genetlink.c:673 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:718 [inline]
genl_rcv_msg+0x627/0xdf0 net/netlink/genetlink.c:735
netlink_rcv_skb+0x15a/0x410 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:746
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x537/0x740 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x882/0xe10 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6e6/0x810 net/socket.c:2352
___sys_sendmsg+0x100/0x170 net/socket.c:2406
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2439
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
RIP: 0033:0x45ca29
Code: 0d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007effe76edc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004fe1c0 RCX: 000000000045ca29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000005
RBP: 000000000078bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 000000000000094e R14: 00000000004d5d00 R15: 00007effe76ee6d4
Allocated by task 3018:
save_stack+0x1b/0x40 mm/kasan/common.c:49
set_track mm/kasan/common.c:57 [inline]
__kasan_kmalloc mm/kasan/common.c:495 [inline]
__kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:468
__do_kmalloc mm/slab.c:3656 [inline]
__kmalloc+0x161/0x7a0 mm/slab.c:3665
kmalloc include/linux/slab.h:560 [inline]
sk_prot_alloc+0x223/0x2f0 net/core/sock.c:1612
sk_alloc+0x36/0x1100 net/core/sock.c:1666
data_sock_create drivers/isdn/mISDN/socket.c:600 [inline]
mISDN_sock_create+0x272/0x400 drivers/isdn/mISDN/socket.c:796
__sock_create+0x3cb/0x730 net/socket.c:1428
sock_create net/socket.c:1479 [inline]
__sys_socket+0xef/0x200 net/socket.c:1521
__do_sys_socket net/socket.c:1530 [inline]
__se_sys_socket net/socket.c:1528 [inline]
__x64_sys_socket+0x6f/0xb0 net/socket.c:1528
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
Freed by task 2484:
save_stack+0x1b/0x40 mm/kasan/common.c:49
set_track mm/kasan/common.c:57 [inline]
kasan_set_free_info mm/kasan/common.c:317 [inline]
__kasan_slab_free+0xf7/0x140 mm/kasan/common.c:456
__cache_free mm/slab.c:3426 [inline]
kfree+0x109/0x2b0 mm/slab.c:3757
kvfree+0x42/0x50 mm/util.c:603
__free_fdtable+0x2d/0x70 fs/file.c:31
put_files_struct fs/file.c:420 [inline]
put_files_struct+0x248/0x2e0 fs/file.c:413
exit_files+0x7e/0xa0 fs/file.c:445
do_exit+0xb04/0x2dd0 kernel/exit.c:791
do_group_exit+0x125/0x340 kernel/exit.c:894
get_signal+0x47b/0x24e0 kernel/signal.c:2739
do_signal+0x81/0x2240 arch/x86/kernel/signal.c:784
exit_to_usermode_loop+0x26c/0x360 arch/x86/entry/common.c:161
prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline]
syscall_return_slowpath arch/x86/entry/common.c:279 [inline]
do_syscall_64+0x6b1/0x7d0 arch/x86/entry/common.c:305
entry_SYSCALL_64_after_hwframe+0x49/0xb3
The buggy address belongs to the object at ffff88808ed0c000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1424 bytes inside of
2048-byte region [ffff88808ed0c000, ffff88808ed0c800)
The buggy address belongs to the page:
page:ffffea00023b4300 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0xfffe0000000200(slab)
raw: 00fffe0000000200 ffffea0002838208 ffffea00015ba288 ffff8880aa000e00
raw: 0000000000000000 ffff88808ed0c000 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808ed0c480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88808ed0c500: 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808ed0c580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88808ed0c600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88808ed0c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 6b9f34239b ("l2tp: fix races in tunnel creation")
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Cc: Guillaume Nault <gnault@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 539d39ad0c ]
Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a96ac8a004 ]
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79dde73cf9 ]
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac8372f3b4 ]
On s390, the layout of normal and large ptes (i.e. pmds/puds) differs.
Therefore, set_huge_pte_at() does a conversion from a normal pte to
the corresponding large pmd/pud. So, when converting an empty pte, this
should result in an empty pmd/pud, which would return true for
pmd/pud_none().
However, after conversion we also mark the pmd/pud as large, and
therefore present. For empty ptes, this will result in an empty pmd/pud
that is also marked as large, and pmd/pud_none() would not return true.
There is currently no issue with this behaviour, as set_huge_pte_at()
does not seem to be called for empty ptes. It would be valid though, so
let's fix this by not marking empty ptes as large in set_huge_pte_at().
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add more arch page table helper
tests").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef01cee2ee ]
In bmac_get_station_address, We're reading two bytes at a time from ROM,
but we do that six times, resulting in 12 bytes of read & writes. This
means we will write off the end of the six-byte destination buffer.
This change fixes the for-loop to only read/write six bytes.
Based on a proposed fix from Finn Thain <fthain@telegraphics.com.au>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7110a26e5 ]
When building with Clang + -Wtautological-compare and
CONFIG_CPUMASK_OFFSTACK unset:
arch/x86/mm/mmio-mod.c:375:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL &&
^~~~~~~~~~~ ~~~~
arch/x86/mm/mmio-mod.c:405:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL || cpumask_weight(downed_cpus) == 0)
^~~~~~~~~~~ ~~~~
2 warnings generated.
Commit
f7e30f01a9 ("cpumask: Add helper cpumask_available()")
added cpumask_available() to fix warnings of this nature. Use that here
so that clang does not warn regardless of CONFIG_CPUMASK_OFFSTACK's
value.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/982
Link: https://lkml.kernel.org/r/20200408205323.44490-1-natechancellor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d4c797749 ]
Use a mutex to protect access to idev->msg_len, idev->buf, etc. which
are modified by both altr_i2c_xfer_msg() and altr_i2c_isr().
This is the minimal fix for easy backporting. A cleanup to remove the
spinlock will be added later.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 770f60586d ]
This patch fixes the following warning and few other instances of
traversal of evm_config_xattrnames list:
[ 32.848432] =============================
[ 32.848707] WARNING: suspicious RCU usage
[ 32.848966] 5.7.0-rc1-00006-ga8d5875ce5f0b #1 Not tainted
[ 32.849308] -----------------------------
[ 32.849567] security/integrity/evm/evm_main.c:231 RCU-list traversed in non-reader section!!
Since entries are only added to the list and never deleted, use
list_for_each_entry_lockless() instead of list_for_each_entry_rcu for
traversing the list. Also, add a relevant comment in evm_secfs.c to
indicate this fact.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org> (RCU viewpoint)
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799587d573 ]
Elide invalid configuration EZNPS + ARCv2, triggered by a
make allyesconfig build.
Granted the root cause is in source code (asm/barrier.h) where we check
for ARCv2 before PLAT_EZNPS, but it is better to avoid such combinations
at onset rather then baking subtle nuances into code.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43900edf67 ]
As of today the ICCM and DCCM size checks are incorrectly using
mismatched units (KiB checked against bytes). The CONFIG_ARC_DCCM_SZ
and CONFIG_ARC_ICCM_SZ are in KiB, but the size calculated in
runtime and stored in cpu->dccm.sz and cpu->iccm.sz is in bytes.
Fix that.
Reported-by: Paul Greco <pmgreco@us.ibm.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4adfe5591 ]
A typical backtrace acquired from ftraced function currently looks like
the following (e.g. for "path_openat"):
arch_stack_walk+0x15c/0x2d8
stack_trace_save+0x50/0x68
stack_trace_call+0x15a/0x3b8
ftrace_graph_caller+0x0/0x1c
0x3e0007e3c98 <- ftraced function caller (should be do_filp_open+0x7c/0xe8)
do_open_execat+0x70/0x1b8
__do_execve_file.isra.0+0x7d8/0x860
__s390x_sys_execve+0x56/0x68
system_call+0xdc/0x2d8
Note random "0x3e0007e3c98" stack value as ftraced function caller. This
value causes either imprecise unwinder result or unwinding failure.
That "0x3e0007e3c98" comes from r14 of ftraced function stack frame, which
it haven't had a chance to initialize since the very first instruction
calls ftrace code ("ftrace_caller"). (ftraced function might never
save r14 as well). Nevertheless according to s390 ABI any function
is called with stack frame allocated for it and r14 contains return
address. "ftrace_caller" itself is called with "brasl %r0,ftrace_caller".
So, to fix this issue simply always save traced function caller onto
ftraced function stack frame.
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfda044533 ]
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1
Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48e626ac85 ]
export_imc_mode_and_cmd() function which creates the debugfs interface
for imc-mode and imc-command, is invoked when each nest pmu units is
registered.
When the first nest pmu unit is registered, export_imc_mode_and_cmd()
creates 'imc' directory under `/debug/powerpc/`. In the subsequent
invocations debugfs_create_dir() function returns, since the directory
already exists.
The recent commit <c33d442328f55> (debugfs: make error message a bit
more verbose), throws a warning if we try to invoke
`debugfs_create_dir()` with an already existing directory name.
Address this warning by making the debugfs directory registration in
the opal_imc_counters_probe() function, i.e invoke
export_imc_mode_and_cmd() function from the probe function.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Tested-by: Nageswara R Sastry <nasastry@in.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191127072035.4283-1-anju@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38152ea37d upstream.
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e72455b898 upstream.
Fix for non-working buttons on knock-off USB dongles for Sony
controllers. These USB dongles are used to connect older Sony DA/DS1/DS2
controllers via USB and are common on Amazon, AliExpress, etc. Without
the patch, the square, X, and circle buttons do not function. These
dongles used to work prior to kernel 4.10 but removing the global DS3
report fixup in commit e19a267b99 ("HID: sony: DS3 comply to Linux gamepad
spec") exposed the problem.
Many people reported the problem on the Ubuntu forums and are working
around the problem by falling back to the 4.9 hid-sony driver.
The problem stems from these dongles incorrectly reporting their button
count as 13 instead of 16. This patch fixes up the report descriptor by
changing the button report count to 16 and removing 3 padding bits.
Cc: stable@vger.kernel.org
Fixes: e19a267b99 ("HID: sony: DS3 comply to Linux gamepad spec")
Signed-off-by: Scott Shumate <scott.shumate@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8ef4b38cb ]
This reverts commit 9a9e97b2f1 ("cgroup: Add memory barriers to plug
cgroup_rstat_updated() race window").
The commit was added in anticipation of memcg rstat conversion which needed
synchronous accounting for the event counters (e.g. oom kill count). However,
the conversion didn't get merged due to percpu memory overhead concern which
couldn't be addressed at the time.
Unfortunately, the patch's addition of smp_mb() to cgroup_rstat_updated()
meant that every scheduling event now had to go through an additional full
barrier and Mel Gorman noticed it as 1% regression in netperf UDP_STREAM test.
There's no need to have this barrier in tree now and even if we need
synchronous accounting in the future, the right thing to do is separating that
out to a separate function so that hot paths which don't care about
synchronous behavior don't have to pay the overhead of the full barrier. Let's
revert.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Link: http://lkml.kernel.org/r/20200409154413.GK3818@techsingularity.net
Cc: v4.18+
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a068aab422 upstream.
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 07699f9a7c ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15c9738589 upstream.
In function qlcnic_83xx_interrupt_test(), function
qlcnic_83xx_diag_alloc_res() is not handled by function
qlcnic_83xx_diag_free_res() after a call of the function
qlcnic_alloc_mbx_args() failed. Fix this issue by adding
a jump target "fail_mbx_args", and jump to this new target
when qlcnic_alloc_mbx_args() failed.
Fixes: b6b4316c8b ("qlcnic: Handle qlcnic_alloc_mbx_args() failure")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8056e8434 upstream.
We have logic to maintain network counters across resets by storing
the counters in bp->net_stats_prev before reset. But not all resets
will clear the counters. Certain resets that don't need to change
the number of rings do not clear the counters. The current logic
accumulates the counters before all resets, causing big jumps in
the counters after some resets, such as ethtool -G.
Fix it by only accumulating the counters during reset if the irq_re_init
parameter is set. The parameter signifies that all rings and interrupts
will be reset and that means that the counters will also be reset.
Reported-by: Vijayendra Suman <vijayendra.suman@oracle.com>
Fixes: b8875ca356 ("bnxt_en: Save ring statistics before reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
