[ Upstream commit 2b3957c34b ]
Commit 128bb975dc ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.
Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c27bf3c5b ]
r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.
There is also some error since headers are accounted once, but
error rate is small enough that we do not care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f25a2dfc20 ]
This patch fixes nvme queue cleanup if requesting an IRQ handler for
the queue's vector fails. It does this by resetting the cq_vector to
the uninitialized value of -1 so it is ignored for a controller reset.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
[changelog updates, removed misc whitespace changes]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3bf2a09da9 ]
A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit abd6360591 ]
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a145f64c61 ]
Returning -EINVAL when an ioctl is not implemented is a very
bad idea, as it is hard to distinguish from other error
contitions that an ioctl could lead. Replace it by its
right error code: -ENOTTY.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 657308f73e ]
Similar to the ancient commit a5fe8e7695 ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
Fixes: 73d54c9e74 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88e80c6267 ]
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba68878361 ]
We need to enable PM runtime on omap1 also as otherwise we
will get errors:
omap_timer omap_timer.1: omap_dm_timer_probe: pm_runtime_get_sync failed!
omap_timer: probe of omap_timer.1 failed with error -13
...
We are checking for OMAP_TIMER_NEEDS_RESET flag elsewhere so this is
safe to do.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 410d5e13e7 ]
When we terminate driver I/O (because we need to stop using a certain
channel path) we also need to ensure that a timer (which may have been
set up using ccw_device_start_timeout) is cleared.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 770b55c995 ]
When a timeout occurs for users of ccw_device_start_timeout
we will stop the IO and call the drivers int handler with
the irb pointer set to ERR_PTR(-ETIMEDOUT). Sometimes
however we'd set the irb pointer to ERR_PTR(-EIO) which is
not intended. Just set the correct value in all codepaths.
Reported-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 083b209071 ]
I am using SECCOMP to filter syscalls on a ppc32 platform, and noticed
that the JIT compiler was failing on the BPF even though the
interpreter was working fine.
The issue was that the compiler was missing one of the instructions
used by SECCOMP, so here is a patch to enable JIT for that
instruction.
Fixes: eb84bab0fb ("ppc: Kconfig: Enable BPF JIT on ppc32")
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53b8d89ddb ]
gcc warns about a possible overflow of the kmem_cache string, when adding
four characters to a string of the same length:
drivers/md/raid5.c: In function 'setup_conf':
drivers/md/raid5.c:2207:34: error: '-alt' directive writing 4 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~
drivers/md/raid5.c:2207:2: note: 'sprintf' output between 5 and 36 bytes into a destination of size 32
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If I'm counting correctly, we need 11 characters for the fixed part
of the string and 18 characters for a 64-bit pointer (when no gendisk
is used), so that leaves three characters for conf->level, which should
always be sufficient.
This makes the code use snprintf() with the correct length, to
make the code more robust against changes, and to get the compiler
to shut up.
In commit f4be6b43f1 ("md/raid5: ensure we create a unique name for
kmem_cache when mddev has no gendisk") from 2010, Neil said that
the pointer could be removed "shortly" once devices without gendisk
are disallowed. I have no idea if that happened, but if it did, that
should probably be changed as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17539f2f4f ]
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01a69cab01 ]
In the case of 'recover', an r10bio with R10BIO_WriteError &
R10BIO_IsRecover will be progressed by handle_write_completed().
This function traverses all r10bio->devs[copies].
If devs[m].repl_bio != NULL, it thinks conf->mirrors[dev].replacement
is also not NULL. However, this is not always true.
When there is an rdev of raid10 has replacement, then each r10bio
->devs[m].repl_bio != NULL in conf->r10buf_pool. However, in 'recover',
even if corresponded replacement is NULL, it doesn't clear r10bio
->devs[m].repl_bio, resulting in replacement NULL deference.
This bug was introduced when replacement support for raid10 was
added in Linux 3.3.
As NeilBrown suggested:
Elsewhere the determination of "is this device part of the
resync/recovery" is made by resting bio->bi_end_io.
If this is end_sync_write, then we tried to write here.
If it is NULL, then we didn't try to write.
Fixes: 9ad1aefc8a ("md/raid10: Handle replacement devices during resync.")
Cc: stable (V3.3+)
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 651b9920d7 ]
This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe9c842695 ]
The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.
Fixes: d9b8d8e19b ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cbbf1745d ]
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
Correct all wrong usage:
- clk.rate is unsigned long, not u32,
- clk.flags is u8, not u32, which exposed the successive
clk.rate_offset and clk.src_offset fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3be6d2a08 ]
For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.
Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.
For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.
And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.
Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().
In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db35340c53 ]
When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().
In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.
That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.
To fix it, allocate the property dynamically, and delete static one.
Signed-off-by: Qi Hou <qi.hou@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00c20cdc79 ]
When aacraid init fails with "AAC0: adapter self-test failed.", shutdown
leads to UBSAN warning and then oops:
[154316.118423] ================================================================================
[154316.118508] UBSAN: Undefined behaviour in drivers/scsi/scsi_lib.c:2328:27
[154316.118566] member access within null pointer of type 'struct Scsi_Host'
[154316.118631] CPU: 2 PID: 14530 Comm: reboot Tainted: G W 4.15.0-dirty #89
[154316.118701] Hardware name: Hewlett Packard HP NetServer/HP System Board, BIOS 4.06.46 PW 06/25/2003
[154316.118774] Call Trace:
[154316.118848] dump_stack+0x48/0x65
[154316.118916] ubsan_epilogue+0xe/0x40
[154316.118976] __ubsan_handle_type_mismatch+0xfb/0x180
[154316.119043] scsi_block_requests+0x20/0x30
[154316.119135] aac_shutdown+0x18/0x40 [aacraid]
[154316.119196] pci_device_shutdown+0x33/0x50
[154316.119269] device_shutdown+0x18a/0x390
[...]
[154316.123435] BUG: unable to handle kernel NULL pointer dereference at 000000f4
[154316.123515] IP: scsi_block_requests+0xa/0x30
This is because aac_shutdown() does
struct Scsi_Host *shost = pci_get_drvdata(dev);
scsi_block_requests(shost);
and that assumes shost has been assigned with pci_set_drvdata().
However, pci_set_drvdata(pdev, shost) is done in aac_probe_one() far
after bailing out with error from calling the init function
((*aac_drivers[index].init)(aac)), and when the init function fails, no
error is returned from aac_probe_one() so PCI layer assumes there is
driver attached, and tries to shut it down later.
Fix it by returning error from aac_probe_one() when card-specific init
function fails.
This fixes reboot on my HP NetRAID-4M with dead battery.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 755d739534 ]
We should call dwc2_hsotg_enqueue_setup() after properly
setting lx_state. Because it may cause error-out from
dwc2_hsotg_enqueue_setup() due to wrong value in lx_state.
Issue can be reproduced by loading driver while connected
A-Connector (start in A-HOST mode) then disconnect A-Connector
to switch to B-DEVICE.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20c63f4089 ]
Clang reports the following warning:
drivers/usb/gadget/udc/fsl_udc_core.c:1312:10: warning: address of array
'ep->name' will always evaluate to 'true' [-Wpointer-bool-conversion]
if (ep->name)
~~ ~~~~^~~~
It seems that the authors intention was to check if the ep has been
configured through struct_ep_setup. Check whether struct usb_ep name
pointer has been set instead.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8813a59ed8 ]
If there are multiple functions associated with a configuration, then
the UAC2 interfaces may not start at zero. Set the correct first
interface number in the association descriptor so that the audio
interfaces are enumerated correctly in this case.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c02189e12c ]
A left shift must shift less than the bit width of the left argument.
Avoid triggering undefined behavior if ha->mbx_count == 32.
This patch avoids that UBSAN reports the following complaint:
UBSAN: Undefined behaviour in drivers/scsi/qla2xxx/qla_isr.c:275:14
shift exponent 32 is too large for 32-bit type 'int'
Call Trace:
dump_stack+0x4e/0x6c
ubsan_epilogue+0xd/0x3b
__ubsan_handle_shift_out_of_bounds+0x112/0x14c
qla2x00_mbx_completion+0x1c5/0x25d [qla2xxx]
qla2300_intr_handler+0x1ea/0x3bb [qla2xxx]
qla2x00_mailbox_command+0x77b/0x139a [qla2xxx]
qla2x00_mbx_reg_test+0x83/0x114 [qla2xxx]
qla2x00_chip_diag+0x354/0x45f [qla2xxx]
qla2x00_initialize_adapter+0x2c2/0xa4e [qla2xxx]
qla2x00_probe_one+0x1681/0x392e [qla2xxx]
pci_device_probe+0x10b/0x1f1
driver_probe_device+0x21f/0x3a4
__driver_attach+0xa9/0xe1
bus_for_each_dev+0x6e/0xb5
driver_attach+0x22/0x3c
bus_add_driver+0x1d1/0x2ae
driver_register+0x78/0x130
__pci_register_driver+0x75/0xa8
qla2x00_module_init+0x21b/0x267 [qla2xxx]
do_one_initcall+0x5a/0x1e2
do_init_module+0x9d/0x285
load_module+0x20db/0x38e3
SYSC_finit_module+0xa8/0xbc
SyS_finit_module+0x9/0xb
do_syscall_64+0x77/0x271
entry_SYSCALL64_slow_path+0x25/0x25
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7043e9529 ]
My static checker complains about an out of bounds read:
drivers/message/fusion/mptctl.c:2786 mptctl_hp_targetinfo()
error: buffer overflow 'hd->sel_timeout' 255 <= u32max.
It's true that we probably should have a bounds check here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ecf7ff4994 ]
When a request times out we set the io_req flag BNX2FC_FLAG_IO_COMPL so
that if a subsequent completion comes in on that task ID we will ignore
it. The issue is that in the check for this flag there is a missing
return so we will continue to process a request which may have already
been returned to the ownership of the SCSI layer. This can cause
unpredictable results.
Solution is to add in the missing return.
[mkp: typo plus title shortening]
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11dc13224c ]
When queuing on the qspinlock, the count field for the current CPU's head
node is incremented. This needn't be atomic because locking in e.g. IRQ
context is balanced and so an IRQ will return with node->count as it
found it.
However, the compiler could in theory reorder the initialisation of
node[idx] before the increment of the head node->count, causing an
IRQ to overwrite the initialised node and potentially corrupt the lock
state.
Avoid the potential for this harmful compiler reordering by placing a
barrier() between the increment of the head node->count and the subsequent
node initialisation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518528177-19169-3-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3d91b0ca5 ]
V3: More generic skipping of relo-section (suggested by Daniel)
If clang >= 4.0.1 is missing the option '-target bpf', it will cause
llc/llvm to create two ELF sections for "Exception Frames", with
section names '.eh_frame' and '.rel.eh_frame'.
The BPF ELF loader library libbpf fails when loading files with these
sections. The other in-kernel BPF ELF loader in samples/bpf/bpf_load.c,
handle this gracefully. And iproute2 loader also seems to work with these
"eh" sections.
The issue in libbpf is caused by bpf_object__elf_collect() skipping
some sections, and later when performing relocation it will be
pointing to a skipped section, as these sections cannot be found by
bpf_object__find_prog_by_idx() in bpf_object__collect_reloc().
This is a general issue that also occurs for other sections, like
debug sections which are also skipped and can have relo section.
As suggested by Daniel. To avoid keeping state about all skipped
sections, instead perform a direct qlookup in the ELF object. Lookup
the section that the relo-section points to and check if it contains
executable machine instructions (denoted by the sh_flags
SHF_EXECINSTR). Use this check to also skip irrelevant relo-sections.
Note, for samples/bpf/ the '-target bpf' parameter to clang cannot be used
due to incompatibility with asm embedded headers, that some of the samples
include. This is explained in more details by Yonghong Song in bpf_devel_QA.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f4fc93d47 ]
I attach a back-end device to a cache set, and the cache set is not
registered yet, this back-end device did not attach successfully, and no
error returned:
[root]# echo 87859280-fec6-4bcc-20df7ca8f86b > /sys/block/sde/bcache/attach
[root]#
In sysfs_attach(), the return value "v" is initialized to "size" in
the beginning, and if no cache set exist in bch_cache_sets, the "v" value
would not change any more, and return to sysfs, sysfs regard it as success
since the "size" is a positive number.
This patch fixes this issue by assigning "v" with "-ENOENT" in the
initialization.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73ac105be3 ]
back-end device sdm has already attached a cache_set with ID
f67ebe1f-f8bc-4d73-bfe5-9dc88607f119, then try to attach with
another cache set, and it returns with an error:
[root]# cd /sys/block/sdm/bcache
[root]# echo 5ccd0a63-148e-48b8-afa2-aca9cbd6279f > attach
-bash: echo: write error: Invalid argument
After that, execute a command to modify the label of bcache
device:
[root]# echo data_disk1 > label
Then we reboot the system, when the system power on, the back-end
device can not attach to cache_set, a messages show in the log:
Feb 5 12:05:52 ceph152 kernel: [922385.508498] bcache:
bch_cached_dev_attach() couldn't find uuid for sdm in set
In sysfs_attach(), dc->sb.set_uuid was assigned to the value
which input through sysfs, no matter whether it is success
or not in bch_cached_dev_attach(). For example, If the back-end
device has already attached to an cache set, bch_cached_dev_attach()
would fail, but dc->sb.set_uuid was changed. Then modify the
label of bcache device, it will call bch_write_bdev_super(),
which would write the dc->sb.set_uuid to the super block, so we
record a wrong cache set ID in the super block, after the system
reboot, the cache set couldn't find the uuid of the back-end
device, so the bcache device couldn't exist and use any more.
In this patch, we don't assigned cache set ID to dc->sb.set_uuid
in sysfs_attach() directly, but input it into bch_cached_dev_attach(),
and assigned dc->sb.set_uuid to the cache set ID after the back-end
device attached to the cache set successful.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 682811b3ce ]
After long time running of random small IO writing,
I reboot the machine, and after the machine power on,
I found bcache got stuck, the stack is:
[root@ceph153 ~]# cat /proc/2510/task/*/stack
[<ffffffffa06b2455>] closure_sync+0x25/0x90 [bcache]
[<ffffffffa06b6be8>] bch_journal+0x118/0x2b0 [bcache]
[<ffffffffa06b6dc7>] bch_journal_meta+0x47/0x70 [bcache]
[<ffffffffa06be8f7>] bch_prio_write+0x237/0x340 [bcache]
[<ffffffffa06a8018>] bch_allocator_thread+0x3c8/0x3d0 [bcache]
[<ffffffff810a631f>] kthread+0xcf/0xe0
[<ffffffff8164c318>] ret_from_fork+0x58/0x90
[<ffffffffffffffff>] 0xffffffffffffffff
[root@ceph153 ~]# cat /proc/2038/task/*/stack
[<ffffffffa06b1abd>] __bch_btree_map_nodes+0x12d/0x150 [bcache]
[<ffffffffa06b1bd1>] bch_btree_insert+0xf1/0x170 [bcache]
[<ffffffffa06b637f>] bch_journal_replay+0x13f/0x230 [bcache]
[<ffffffffa06c75fe>] run_cache_set+0x79a/0x7c2 [bcache]
[<ffffffffa06c0cf8>] register_bcache+0xd48/0x1310 [bcache]
[<ffffffff812f702f>] kobj_attr_store+0xf/0x20
[<ffffffff8125b216>] sysfs_write_file+0xc6/0x140
[<ffffffff811dfbfd>] vfs_write+0xbd/0x1e0
[<ffffffff811e069f>] SyS_write+0x7f/0xe0
[<ffffffff8164c3c9>] system_call_fastpath+0x16/0x1
The stack shows the register thread and allocator thread
were getting stuck when registering cache device.
I reboot the machine several times, the issue always
exsit in this machine.
I debug the code, and found the call trace as bellow:
register_bcache()
==>run_cache_set()
==>bch_journal_replay()
==>bch_btree_insert()
==>__bch_btree_map_nodes()
==>btree_insert_fn()
==>btree_split() //node need split
==>btree_check_reserve()
In btree_check_reserve(), It will check if there is enough buckets
of RESERVE_BTREE type, since allocator thread did not work yet, so
no buckets of RESERVE_BTREE type allocated, so the register thread
waits on c->btree_cache_wait, and goes to sleep.
Then the allocator thread initialized, the call trace is bellow:
bch_allocator_thread()
==>bch_prio_write()
==>bch_journal_meta()
==>bch_journal()
==>journal_wait_for_write()
In journal_wait_for_write(), It will check if journal is full by
journal_full(), but the long time random small IO writing
causes the exhaustion of journal buckets(journal.blocks_free=0),
In order to release the journal buckets,
the allocator calls btree_flush_write() to flush keys to
btree nodes, and waits on c->journal.wait until btree nodes writing
over or there has already some journal buckets space, then the
allocator thread goes to sleep. but in btree_flush_write(), since
bch_journal_replay() is not finished, so no btree nodes have journal
(condition "if (btree_current_write(b)->journal)" never satisfied),
so we got no btree node to flush, no journal bucket released,
and allocator sleep all the times.
Through the above analysis, we can see that:
1) Register thread wait for allocator thread to allocate buckets of
RESERVE_BTREE type;
2) Alloctor thread wait for register thread to replay journal, so it
can flush btree nodes and get journal bucket.
then they are all got stuck by waiting for each other.
Hua Rui provided a patch for me, by allocating some buckets of
RESERVE_BTREE type in advance, so the register thread can get bucket
when btree node splitting and no need to waiting for the allocator
thread. I tested it, it has effect, and register thread run a step
forward, but finally are still got stuck, the reason is only 8 bucket
of RESERVE_BTREE type were allocated, and in bch_journal_replay(),
after 2 btree nodes splitting, only 4 bucket of RESERVE_BTREE type left,
then btree_check_reserve() is not satisfied anymore, so it goes to sleep
again, and in the same time, alloctor thread did not flush enough btree
nodes to release a journal bucket, so they all got stuck again.
So we need to allocate more buckets of RESERVE_BTREE type in advance,
but how much is enough? By experience and test, I think it should be
as much as journal buckets. Then I modify the code as this patch,
and test in the machine, and it works.
This patch modified base on Hua Rui’s patch, and allocate more buckets
of RESERVE_BTREE type in advance to avoid register thread and allocate
thread going to wait for each other.
[patch v2] ca->sb.njournal_buckets would be 0 in the first time after
cache creation, and no journal exists, so just 8 btree buckets is OK.
Signed-off-by: Hua Rui <huarui.dev@gmail.com>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
