commit b3ae7b67b87fed771fa5bf95389df06b0433603e upstream.
The maximum ring buffer data size is the maximum size of data that can be
recorded on the ring buffer. Events must be smaller than the sub buffer
data size minus any meta data. This size is checked before trying to
allocate from the ring buffer because the allocation assumes that the size
will fit on the sub buffer.
The maximum size was calculated as the size of a sub buffer page (which is
currently PAGE_SIZE minus the sub buffer header) minus the size of the
meta data of an individual event. But it missed the possible adding of a
time stamp for events that are added long enough apart that the event meta
data can't hold the time delta.
When an event is added that is greater than the current BUF_MAX_DATA_SIZE
minus the size of a time stamp, but still less than or equal to
BUF_MAX_DATA_SIZE, the ring buffer would go into an infinite loop, looking
for a page that can hold the event. Luckily, there's a check for this loop
and after 1000 iterations and a warning is emitted and the ring buffer is
disabled. But this should never happen.
This can happen when a large event is added first, or after a long period
where an absolute timestamp is prefixed to the event, increasing its size
by 8 bytes. This passes the check and then goes into the algorithm that
causes the infinite loop.
For events that are the first event on the sub-buffer, it does not need to
add a timestamp, because the sub-buffer itself contains an absolute
timestamp, and adding one is redundant.
The fix is to check if the event is to be the first event on the
sub-buffer, and if it is, then do not add a timestamp.
This also fixes 32 bit adding a timestamp when a read of before_stamp or
write_stamp is interrupted. There's still no need to add that timestamp if
the event is going to be the first event on the sub buffer.
Also, if the buffer has "time_stamp_abs" set, then also check if the
length plus the timestamp is greater than the BUF_MAX_DATA_SIZE.
Link: https://lore.kernel.org/all/20231212104549.58863438@gandalf.local.home/
Link: https://lore.kernel.org/linux-trace-kernel/20231212071837.5fdd6c13@gandalf.local.home
Link: https://lore.kernel.org/linux-trace-kernel/20231212111617.39e02849@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: a4543a2fa9 ("ring-buffer: Get timestamp after event is allocated")
Fixes: 58fbc3c632 ("ring-buffer: Consolidate add_timestamp to remove some branches")
Reported-by: Kent Overstreet <kent.overstreet@linux.dev> # (on IRC)
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b049525855fdd0024881c9b14b8fbec61c3f53d3 upstream.
For the ring buffer iterator (non-consuming read), the event needs to be
copied into the iterator buffer to make sure that a writer does not
overwrite it while the user is reading it. If a write happens during the
copy, the buffer is simply discarded.
But the temp buffer itself was not big enough. The allocation of the
buffer was only BUF_MAX_DATA_SIZE, which is the maximum data size that can
be passed into the ring buffer and saved. But the temp buffer needs to
hold the meta data as well. That would be BUF_PAGE_SIZE and not
BUF_MAX_DATA_SIZE.
Link: https://lore.kernel.org/linux-trace-kernel/20231212072558.61f76493@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 785888c544 ("ring-buffer: Have rb_iter_head_event() handle concurrent writer")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e45e39dc249c970d99d2681f6bcb55736fd725c upstream.
The ring buffer timestamps are synchronized by two timestamp placeholders.
One is the "before_stamp" and the other is the "write_stamp" (sometimes
referred to as the "after stamp" but only in the comments. These two
stamps are key to knowing how to handle nested events coming in with a
lockless system.
When moving across sub-buffers, the before stamp is updated but the write
stamp is not. There's an effort to put back the before stamp to something
that seems logical in case there's nested events. But as the current event
is about to cross sub-buffers, and so will any new nested event that happens,
updating the before stamp is useless, and could even introduce new race
conditions.
The first event on a sub-buffer simply uses the sub-buffer's timestamp
and keeps a "delta" of zero. The "before_stamp" and "write_stamp" are not
used in the algorithm in this case. There's no reason to try to fix the
before_stamp when this happens.
As a bonus, it removes a cmpxchg() when crossing sub-buffers!
Link: https://lore.kernel.org/linux-trace-kernel/20231211114420.36dde01b@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: a389d86f7f ("ring-buffer: Have nested events still record running time stamp")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d06aff1cb13d2a0d52b48e605462518149c98c81 upstream.
The snapshot buffer is to mimic the main buffer so that when a snapshot is
needed, the snapshot and main buffer are swapped. When the snapshot buffer
is allocated, it is set to the minimal size that the ring buffer may be at
and still functional. When it is allocated it becomes the same size as the
main ring buffer, and when the main ring buffer changes in size, it should
do.
Currently, the resize only updates the snapshot buffer if it's used by the
current tracer (ie. the preemptirqsoff tracer). But it needs to be updated
anytime it is allocated.
When changing the size of the main buffer, instead of looking to see if
the current tracer is utilizing the snapshot buffer, just check if it is
allocated to know if it should be updated or not.
Also fix typo in comment just above the code change.
Link: https://lore.kernel.org/linux-trace-kernel/20231210225447.48476a6a@rorschach.local.home
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: ad909e21bb ("tracing: Add internal tracing_snapshot() functions")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17d801758157bec93f26faaf5ff1a8b9a552d67a upstream.
Reading the ring buffer does a swap of a sub-buffer within the ring buffer
with a empty sub-buffer. This allows the reader to have full access to the
content of the sub-buffer that was swapped out without having to worry
about contention with the writer.
The readers call ring_buffer_alloc_read_page() to allocate a page that
will be used to swap with the ring buffer. When the code is finished with
the reader page, it calls ring_buffer_free_read_page(). Instead of freeing
the page, it stores it as a spare. Then next call to
ring_buffer_alloc_read_page() will return this spare instead of calling
into the memory management system to allocate a new page.
Unfortunately, on freeing of the ring buffer, this spare page is not
freed, and causes a memory leak.
Link: https://lore.kernel.org/linux-trace-kernel/20231210221250.7b9cc83c@rorschach.local.home
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 73a757e631 ("ring-buffer: Return reader page back into existing ring buffer")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab4750332dbe535243def5dcebc24ca00c1f98ac upstream.
Add begin/end_use ring callbacks to disallow GFXOFF when
SDMA work is submitted and allow it again afterward.
This should avoid corner cases where GFXOFF is erroneously
entered when SDMA is still active. For now just allow/disallow
GFXOFF in the begin and end helpers until we root cause the
issue. This should not impact power as SDMA usage is pretty
minimal and GFXOSS should not be active when SDMA is active
anyway, this just makes it explicit.
v2: move everything into sdma5.2 code. No reason for this
to be generic at this point.
v3: Add comments in new code
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2220
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> (v1)
Tested-by: Mario Limonciello <mario.limonciello@amd.com> (v1)
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c12296bbecc488623b7d1932080e394d08f3226b upstream.
In __team_options_register, team_options are allocated and appended to
the team's option_list.
If one option instance allocation fails, the "inst_rollback" cleanup
path frees the previously allocated options but doesn't remove them from
the team's option_list.
This leaves dangling pointers that can be dereferenced later by other
parts of the team driver that iterate over options.
This patch fixes the cleanup path to remove the dangling pointers from
the list.
As far as I can tell, this uaf doesn't have much security implications
since it would be fairly hard to exploit (an attacker would need to make
the allocation of that specific small object fail) but it's still nice
to fix.
Cc: stable@vger.kernel.org
Fixes: 80f7c6683f ("team: add support for per-port options")
Signed-off-by: Florent Revest <revest@chromium.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20231206123719.1963153-1-revest@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0696076aad60a2f04c019761921954579e1b0e upstream.
It is currently possible for a userspace application to enter an
infinite page fault loop when using HugeTLB pages implemented with
contiguous PTEs when HAFDBS is not available. This happens because:
1. The kernel may sometimes write PTEs that are sw-dirty but hw-clean
(PTE_DIRTY | PTE_RDONLY | PTE_WRITE).
2. If, during a write, the CPU uses a sw-dirty, hw-clean PTE in handling
the memory access on a system without HAFDBS, we will get a page
fault.
3. HugeTLB will check if it needs to update the dirty bits on the PTE.
For contiguous PTEs, it will check to see if the pgprot bits need
updating. In this case, HugeTLB wants to write a sequence of
sw-dirty, hw-dirty PTEs, but it finds that all the PTEs it is about
to overwrite are all pte_dirty() (pte_sw_dirty() => pte_dirty()),
so it thinks no update is necessary.
We can get the kernel to write a sw-dirty, hw-clean PTE with the
following steps (showing the relevant VMA flags and pgprot bits):
i. Create a valid, writable contiguous PTE.
VMA vmflags: VM_SHARED | VM_READ | VM_WRITE
VMA pgprot bits: PTE_RDONLY | PTE_WRITE
PTE pgprot bits: PTE_DIRTY | PTE_WRITE
ii. mprotect the VMA to PROT_NONE.
VMA vmflags: VM_SHARED
VMA pgprot bits: PTE_RDONLY
PTE pgprot bits: PTE_DIRTY | PTE_RDONLY
iii. mprotect the VMA back to PROT_READ | PROT_WRITE.
VMA vmflags: VM_SHARED | VM_READ | VM_WRITE
VMA pgprot bits: PTE_RDONLY | PTE_WRITE
PTE pgprot bits: PTE_DIRTY | PTE_WRITE | PTE_RDONLY
Make it impossible to create a writeable sw-dirty, hw-clean PTE with
pte_modify(). Such a PTE should be impossible to create, and there may
be places that assume that pte_dirty() implies pte_hw_dirty().
Signed-off-by: James Houghton <jthoughton@google.com>
Fixes: 031e6e6b4e ("arm64: hugetlb: Avoid unnecessary clearing in huge_ptep_set_access_flags")
Cc: <stable@vger.kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20231204172646.2541916-3-jthoughton@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dcf5fde6dffb312a4bfb8ef940cea2d1f402e32 upstream.
For files with logical blocks close to EXT_MAX_BLOCKS, the file size
predicted in ext4_mb_normalize_request() may exceed EXT_MAX_BLOCKS.
This can cause some blocks to be preallocated that will not be used.
And after [Fixes], the following issue may be triggered:
=========================================================
kernel BUG at fs/ext4/mballoc.c:4653!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
CPU: 1 PID: 2357 Comm: xfs_io 6.7.0-rc2-00195-g0f5cc96c367f
Hardware name: linux,dummy-virt (DT)
pc : ext4_mb_use_inode_pa+0x148/0x208
lr : ext4_mb_use_inode_pa+0x98/0x208
Call trace:
ext4_mb_use_inode_pa+0x148/0x208
ext4_mb_new_inode_pa+0x240/0x4a8
ext4_mb_use_best_found+0x1d4/0x208
ext4_mb_try_best_found+0xc8/0x110
ext4_mb_regular_allocator+0x11c/0xf48
ext4_mb_new_blocks+0x790/0xaa8
ext4_ext_map_blocks+0x7cc/0xd20
ext4_map_blocks+0x170/0x600
ext4_iomap_begin+0x1c0/0x348
=========================================================
Here is a calculation when adjusting ac_b_ex in ext4_mb_new_inode_pa():
ex.fe_logical = orig_goal_end - EXT4_C2B(sbi, ex.fe_len);
if (ac->ac_o_ex.fe_logical >= ex.fe_logical)
goto adjust_bex;
The problem is that when orig_goal_end is subtracted from ac_b_ex.fe_len
it is still greater than EXT_MAX_BLOCKS, which causes ex.fe_logical to
overflow to a very small value, which ultimately triggers a BUG_ON in
ext4_mb_new_inode_pa() because pa->pa_free < len.
The last logical block of an actual write request does not exceed
EXT_MAX_BLOCKS, so in ext4_mb_normalize_request() also avoids normalizing
the last logical block to exceed EXT_MAX_BLOCKS to avoid the above issue.
The test case in [Link] can reproduce the above issue with 64k block size.
Link: https://patchwork.kernel.org/project/fstests/list/?series=804003
Cc: <stable@kernel.org> # 6.4
Fixes: 93cdf49f6e ("ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231127063313.3734294-1-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e199bf52ffda8f98f129728d57244a9cd9ad5623 upstream.
If bus is marked as multi_link, but number of masters in the stream is
not higher than bus->hw_sync_min_links (bus->multi_link && m_rt_count >=
bus->hw_sync_min_links), bank switching should not happen. The first
part of do_bank_switch() code properly takes these conditions into
account, but second part (sdw_ml_sync_bank_switch()) relies purely on
bus->multi_link property. This is not balanced and leads to NULL
pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Call trace:
wait_for_completion_timeout+0x124/0x1f0
do_bank_switch+0x370/0x6f8
sdw_prepare_stream+0x2d0/0x438
qcom_snd_sdw_prepare+0xa0/0x118
sm8450_snd_prepare+0x128/0x148
snd_soc_link_prepare+0x5c/0xe8
__soc_pcm_prepare+0x28/0x1ec
dpcm_be_dai_prepare+0x1e0/0x2c0
dpcm_fe_dai_prepare+0x108/0x28c
snd_pcm_do_prepare+0x44/0x68
snd_pcm_action_single+0x54/0xc0
snd_pcm_action_nonatomic+0xe4/0xec
snd_pcm_prepare+0xc4/0x114
snd_pcm_common_ioctl+0x1154/0x1cc0
snd_pcm_ioctl+0x54/0x74
Fixes: ce6e74d008 ("soundwire: Add support for multi link bank switch")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231124180136.390621-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8892fd71933126ebae3d60aec5918d4dceaae76 upstream.
Our btrfs subvolume snapshot <source> <destination> utility enforces
that <source> is the root of the subvolume, however this isn't enforced
in the kernel. Update the kernel to also enforce this limitation to
avoid problems with other users of this ioctl that don't have the
appropriate checks in place.
Reported-by: Martin Michaelis <code@mgjm.de>
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e2c1e4b34f07d9aa8937fab88359d4a0fce468e upstream.
When lockdep is enabled, the for_each_sibling_event(sibling, event)
macro checks that event->ctx->mutex is held. When creating a new group
leader event, we call perf_event_validate_size() on a partially
initialized event where event->ctx is NULL, and so when
for_each_sibling_event() attempts to check event->ctx->mutex, we get a
splat, as reported by Lucas De Marchi:
WARNING: CPU: 8 PID: 1471 at kernel/events/core.c:1950 __do_sys_perf_event_open+0xf37/0x1080
This only happens for a new event which is its own group_leader, and in
this case there cannot be any sibling events. Thus it's safe to skip the
check for siblings, which avoids having to make invasive and ugly
changes to for_each_sibling_event().
Avoid the splat by bailing out early when the new event is its own
group_leader.
Fixes: 382c27f4ed28f803 ("perf: Fix perf_event_validate_size()")
Closes: https://lore.kernel.org/lkml/20231214000620.3081018-1-lucas.demarchi@intel.com/
Closes: https://lore.kernel.org/lkml/ZXpm6gQ%2Fd59jGsuW@xpf.sh.intel.com/
Reported-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231215112450.3972309-1-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06ae5afce8cc1f7621cc5c7751e449ce20d68af7 ]
In the function asus_kbd_set_report the parameter buf is read-only
as it gets copied in a memory portion suitable for USB transfer,
but the parameter is not marked as const: add the missing const and mark
const immutable buffers passed to that function.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 125b0bb95dd6bec81b806b997a4ccb026eeecf8f ]
We really don't want to do atomic_read() or anything like that, since we
already have the value, not the lock. The whole point of this is that
we've loaded the lock from memory, and we want to check whether the
value we loaded was a locked one or not.
The main use of this is the lockref code, which loads both the lock and
the reference count in one atomic operation, and then works on that
combined value. With the atomic_read(), the compiler would pointlessly
spill the value to the stack, in order to then be able to read it back
"atomically".
This is the qspinlock version of commit c6f4a9002252 ("asm-generic:
ticket-lock: Optimize arch_spin_value_unlocked()") which fixed this same
bug for ticket locks.
Cc: Guo Ren <guoren@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Link: https://lore.kernel.org/all/CAHk-=whNRv0v6kQiV5QO6DJhjH4KEL36vWQ6Re8Csrnh4zbRkQ@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ffccb691adb854e7b7f3ee57fbbda12ff70533f ]
Honor MagicBook 13 2023 has a touchpad which do not switch to the multitouch
mode until the input mode feature is written by the host. The touchpad do
report the input mode at touchpad(3), while itself working under mouse mode. As
a workaround, it is possible to call MT_QUIRE_FORCE_GET_FEATURE to force set
feature in mt_set_input_mode for such device.
The touchpad reports as BLTP7853, which cannot retrive any useful manufacture
information on the internel by this string at present. As the serial number of
the laptop is GLO-G52, while DMI info reports the laptop serial number as
GLO-GXXX, this workaround should applied to all models which has the GLO-GXXX.
Signed-off-by: Aoba K <nexp_0x17@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 546edbd26cff7ae990e480a59150e801a06f77b1 ]
Some devices managed by this driver automatically set brightness to 0
before entering a suspended state and reset it back to a default
brightness level after the resume:
this has the effect of having the kernel report wrong brightness
status after a sleep, and on some devices (like the Asus RC71L) that
brightness is the intensity of LEDs directly facing the user.
Fix the above issue by setting back brightness to the level it had
before entering a sleep state.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55092187d9ad7b2f8f5a8645286fa03997d442f ]
These devices disconnect if suspended without remote wakeup. They can operate
with the standard driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5e913c25b6b2b6ae02acef6d9400645ac03dfdf ]
The Glorious Model I mouse has a buggy HID report descriptor for its
keyboard endpoint (used for programmable buttons). For report ID 2, there
is a mismatch between Logical Minimum and Usage Minimum in the array that
reports keycodes.
The offending portion of the descriptor: (from hid-decode)
0x95, 0x05, // Report Count (5) 30
0x75, 0x08, // Report Size (8) 32
0x15, 0x00, // Logical Minimum (0) 34
0x25, 0x65, // Logical Maximum (101) 36
0x05, 0x07, // Usage Page (Keyboard) 38
0x19, 0x01, // Usage Minimum (1) 40
0x29, 0x65, // Usage Maximum (101) 42
0x81, 0x00, // Input (Data,Arr,Abs) 44
This bug shifts all programmed keycodes up by 1. Importantly, this causes
"empty" array indexes of 0x00 to be interpreted as 0x01, ErrorRollOver.
The presence of ErrorRollOver causes the system to ignore all keypresses
from the endpoint and breaks the ability to use the programmable buttons.
Setting byte 41 to 0x00 fixes this, and causes keycodes to be interpreted
correctly.
Also, USB_VENDOR_ID_GLORIOUS is changed to USB_VENDOR_ID_SINOWEALTH,
and a new ID for Laview Technology is added. Glorious seems to be
white-labeling controller boards or mice from these vendors. There isn't a
single canonical vendor ID for Glorious products.
Signed-off-by: Brett Raye <braye@fastmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eba5e0b2422aec3c9e79822029599961fdcab97 ]
In run_cache_set() after c->root returned from bch_btree_node_get(), it
is checked by IS_ERR_OR_NULL(). Indeed it is unncessary to check NULL
because bch_btree_node_get() will not return NULL pointer to caller.
This patch replaces IS_ERR_OR_NULL() by IS_ERR() for the above reason.
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20231120052503.6122-11-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31f5b956a197d4ec25c8a07cb3a2ab69d0c0b82f ]
This patch adds code comments to bch_btree_node_get() and
__bch_btree_node_alloc() that NULL pointer will not be returned and it
is unnecessary to check NULL pointer by the callers of these routines.
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20231120052503.6122-10-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be93825f0e6428c2d3f03a6e4d447dc48d33d7ff ]
Variable cur_idx is being initialized with a value that is never read,
it is being re-assigned later in a while-loop. Remove the redundant
assignment. Cleans up clang scan build warning:
drivers/md/bcache/writeback.c:916:2: warning: Value stored to 'cur_idx'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20231120052503.6122-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf8fb7e0e5ec54ea0839f0c534f2cdcd79bea9c ]
Arraies bcache->stripe_sectors_dirty and bcache->full_dirty_stripes are
used for dirty data writeback, their sizes are decided by backing device
capacity and stripe size. Larger backing device capacity or smaller
stripe size make these two arraies occupies more dynamic memory space.
Currently bcache->stripe_size is directly inherited from
queue->limits.io_opt of underlying storage device. For normal hard
drives, its limits.io_opt is 0, and bcache sets the corresponding
stripe_size to 1TB (1<<31 sectors), it works fine 10+ years. But for
devices do declare value for queue->limits.io_opt, small stripe_size
(comparing to 1TB) becomes an issue for oversize memory allocations of
bcache->stripe_sectors_dirty and bcache->full_dirty_stripes, while the
capacity of hard drives gets much larger in recent decade.
For example a raid5 array assembled by three 20TB hardrives, the raid
device capacity is 40TB with typical 512KB limits.io_opt. After the math
calculation in bcache code, these two arraies will occupy 400MB dynamic
memory. Even worse Andrea Tomassetti reports that a 4KB limits.io_opt is
declared on a new 2TB hard drive, then these two arraies request 2GB and
512MB dynamic memory from kzalloc(). The result is that bcache device
always fails to initialize on his system.
To avoid the oversize memory allocation, bcache->stripe_size should not
directly inherited by queue->limits.io_opt from the underlying device.
This patch defines BCH_MIN_STRIPE_SZ (4MB) as minimal bcache stripe size
and set bcache device's stripe size against the declared limits.io_opt
value from the underlying storage device,
- If the declared limits.io_opt > BCH_MIN_STRIPE_SZ, bcache device will
set its stripe size directly by this limits.io_opt value.
- If the declared limits.io_opt < BCH_MIN_STRIPE_SZ, bcache device will
set its stripe size by a value multiplying limits.io_opt and euqal or
large than BCH_MIN_STRIPE_SZ.
Then the minimal stripe size of a bcache device will always be >= 4MB.
For a 40TB raid5 device with 512KB limits.io_opt, memory occupied by
bcache->stripe_sectors_dirty and bcache->full_dirty_stripes will be 50MB
in total. For a 2TB hard drive with 4KB limits.io_opt, memory occupied
by these two arraies will be 2.5MB in total.
Such mount of memory allocated for bcache->stripe_sectors_dirty and
bcache->full_dirty_stripes is reasonable for most of storage devices.
Reported-by: Andrea Tomassetti <andrea.tomassetti-opensource@devo.com>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@lists.ewheeler.net>
Link: https://lore.kernel.org/r/20231120052503.6122-2-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27b13e209ddca5979847a1b57890e0372c1edcee ]
Inside blkg_for_each_descendant_pre(), both
css_for_each_descendant_pre() and blkg_lookup() requires RCU read lock,
and either cgroup_assert_mutex_or_rcu_locked() or rcu_read_lock_held()
is called.
Fix the warning by adding rcu read lock.
Reported-by: Changhui Zhong <czhong@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231117023527.3188627-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fbd5fc2b35a8f559a6b380dfa9bcd964a758186 ]
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccab434e674ca95d483788b1895a70c21b7f016a ]
If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.
The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.
The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ef61a0405742a9f7f6051bc6fd2f017d87d07911 upstream.
This is a partial revert of 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
Fixes: 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS increases")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217680
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1035587
Link: https://lore.kernel.org/r/20231201115028.84351-1-jiaxun.yang@flygoat.com
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5df12742b7e3aae2594a30a9d14d5d6e9e7699f4 upstream.
This reverts commit 40613da52b and the
subsequent fix to it:
cc22522fd5 ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus")
40613da52b fixed a problem where hot-adding a device with large BARs
failed if the bridge windows programmed by firmware were not large enough.
cc22522fd5 ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources()
only for non-root bus") fixed a problem with 40613da52b: an ACPI hot-add
of a device on a PCI root bus (common in the virt world) or firmware
sending ACPI Bus Check to non-existent Root Ports (e.g., on Dell Inspiron
7352/0W6WV0) caused a NULL pointer dereference and suspend/resume hangs.
Unfortunately the combination of 40613da52b and cc22522fd5 caused other
problems:
- Fiona reported that hot-add of SCSI disks in QEMU virtual machine fails
sometimes.
- Dongli reported a similar problem with hot-add of SCSI disks.
- Jonathan reported a console freeze during boot on bare metal due to an
error in radeon GPU initialization.
Revert both patches to avoid adding these problems. This means we will
again see the problems with hot-adding devices with large BARs and the NULL
pointer dereferences and suspend/resume issues that 40613da52b and
cc22522fd5 were intended to fix.
Fixes: 40613da52b ("PCI: acpiphp: Reassign resources on bridge if necessary")
Fixes: cc22522fd5 ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus")
Reported-by: Fiona Ebner <f.ebner@proxmox.com>
Closes: https://lore.kernel.org/r/9eb669c0-d8f2-431d-a700-6da13053ae54@proxmox.com
Reported-by: Dongli Zhang <dongli.zhang@oracle.com>
Closes: https://lore.kernel.org/r/3c4a446a-b167-11b8-f36f-d3c1b49b42e9@oracle.com
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Closes: https://lore.kernel.org/r/ZXpaNCLiDM+Kv38H@marvin.atrad.com.au
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f8ed28d1401320bcb02dda81b3c23ab2dc5a6d8 upstream.
fuse_dax_conn_free() will be called when fuse_fill_super_common() fails
after fuse_dax_conn_alloc(). Then deactivate_locked_super() in
virtio_fs_get_tree() will call virtio_kill_sb() to release the discarded
superblock. This will call fuse_dax_conn_free() again in fuse_conn_put(),
resulting in a possible double free.
Fixes: 1dd539577c ("virtiofs: add a mount option to enable dax")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Cc: <stable@vger.kernel.org> # v5.10
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8fa5d76925991976b3e7076f9d1052515ec1fca upstream.
There are multiple ways to grab references to credentials, and the only
protection we have against overflowing it is the memory required to do
so.
With memory sizes only moving in one direction, let's bump the reference
count to 64-bit and move it outside the realm of feasibly overflowing.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 189ff16722ee36ced4d2a2469d4ab65a8fee4198 ]
Because atalk_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with atalk_recvmsg().
A use-after-free for skb occurs with the following flow.
```
atalk_ioctl() -> skb_peek()
atalk_recvmsg() -> skb_recv_datagram() -> skb_free_datagram()
```
Add sk->sk_receive_queue.lock to atalk_ioctl() to fix this issue.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Link: https://lore.kernel.org/r/20231213041056.GA519680@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 839612d23f ]
I have a board where these two lines are always printed during boot:
imx-dwmac 30bf0000.ethernet: Cannot register the MDIO bus
imx-dwmac 30bf0000.ethernet: stmmac_dvr_probe: MDIO bus (id: 1) registration failed
It's perfectly fine, and the device is successfully (and silently, as
far as the console goes) probed later.
Use dev_err_probe() instead, which will demote these messages to debug
level (thus removing the alarming messages from the console) when the
error is -EPROBE_DEFER, and also has the advantage of including the
error code if/when it happens to be something other than -EPROBE_DEFER.
While here, add the missing \n to one of the format strings.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20220602074840.1143360-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: e23c0d21ce92 ("net: stmmac: Handle disabled MDIO busses from devicetree")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829649443e78d85db0cff0c37cadb28fbb1a5f6f ]
There are some wrong return values check in sign-file when call OpenSSL
API. The ERR() check cond is wrong because of the program only check the
return value is < 0 which ignored the return val is 0. For example:
1. CMS_final() return 1 for success or 0 for failure.
2. i2d_CMS_bio_stream() returns 1 for success or 0 for failure.
3. i2d_TYPEbio() return 1 for success and 0 for failure.
4. BIO_free() return 1 for success and 0 for failure.
Link: https://www.openssl.org/docs/manmaster/man3/
Fixes: e5a2e3c847 ("scripts/sign-file.c: Add support for signing with a raw signature")
Signed-off-by: Yusong Gao <a869920004@gmail.com>
Reviewed-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20231213024405.624692-1-a869920004@gmail.com/ # v5
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e87d3a1370ce9f04770d789bcf7cce44865d2e8d ]
Generic code will use mdio. If it is not initialized before use,
the kernel will Oops.
Fixes: 30bba69d7d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ab138ca0a340e6d6e7a6a9bd5004bd8f83127ca ]
When sending TX packets, the meta descriptor can be all zeroes
as no meta information is required (as in XDP).
This patch removes the validity check, as when
`disable_meta_caching` is enabled, such TX packets will be
dropped otherwise.
Fixes: 0e3a3f6dac ("net: ena: support new LLQ acceleration mode")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20231211062801.27891-5-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 505b1a88d311ff6f8c44a34f94e3be21745cce6f ]
Current xdp code drops packets larger than ENA_XDP_MAX_MTU.
This is an incorrect condition since the problem is not the
size of the packet, rather the number of buffers it contains.
This commit:
1. Identifies and drops XDP multi-buffer packets at the
beginning of the function.
2. Increases the xdp drop statistic when this drop occurs.
3. Adds a one-time print that such drops are happening to
give better indication to the user.
Fixes: 838c93dc54 ("net: ena: implement XDP drop support")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20231211062801.27891-3-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41db6f99b5489a0d2ef26afe816ef0c6118d1d47 ]
The ena_setup_and_create_all_xdp_queues() function freed all the
resources upon failure, after creating only xdp_num_queues queues,
instead of freeing just the created ones.
In this patch, the only resources that are freed, are the ones
allocated right before the failure occurs.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shahar Itzko <itzko@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20231211062801.27891-2-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b65d52ac9c085c0c52dee012a210d4e2f352611b ]
qed_ilt_shadow_alloc() will call qed_ilt_shadow_free() to
free p_hwfn->p_cxt_mngr->ilt_shadow on error. However,
qed_cxt_tables_alloc() accesses the freed pointer on failure
of qed_ilt_shadow_alloc() through calling qed_cxt_mngr_free(),
which may lead to use-after-free. Fix this issue by setting
p_mngr->ilt_shadow to NULL in qed_ilt_shadow_free().
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20231210045255.21383-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 810c38a369a0a0ce625b5c12169abce1dd9ccd53 ]
Because rose_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with rose_accept().
A use-after-free for skb occurs with the following flow.
```
rose_ioctl() -> skb_peek()
rose_accept() -> skb_dequeue() -> kfree_skb()
```
Add sk->sk_receive_queue.lock to rose_ioctl() to fix this issue.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Link: https://lore.kernel.org/r/20231209100538.GA407321@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
