[ Upstream commit 84bc4f1dbb ]
We observed the error "cacheline tracking ENOMEM, dma-debug disabled"
during a light system load (copying some files). The reason for this error
is that the dma_active_cacheline radix tree uses GFP_NOWAIT allocation -
so it can't access the emergency memory reserves and it fails as soon as
anybody reaches the watermark.
This patch changes GFP_NOWAIT to GFP_ATOMIC, so that it can access the
emergency memory reserves.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad68598046 ]
DAPM tracks and reports the value presented to the user from DAPM controls
separately to the register value, these may diverge during initialisation
or when an autodisable control is in use.
When writing DAPM controls we currently report that a change has occurred
if either the DAPM value or the value stored in the register has changed,
meaning that if the two are out of sync we may appear to report a spurious
event to userspace. Since we use this folded in value for nothing other
than the value reported to userspace simply drop the folding in of the
register change.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220428161833.3690050-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e999a5da28 ]
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
[1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
Signed-off-by: Thibaut VARÈNE <hacks+kernel@slashdirt.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220417145145.1847-1-hacks+kernel@slashdirt.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3fa2becf2 ]
In function si_parse_power_table(), array adev->pm.dpm.ps and its member
is allocated. If the allocation of each member fails, the array itself
is freed and returned with an error code. However, the array is later
freed again in si_dpm_fini() function which is called when the function
returns an error.
This leads to potential double free of the array adev->pm.dpm.ps, as
well as leak of its array members, since the members are not freed in
the allocation function and the array is not nulled when freed.
In addition adev->pm.dpm.num_ps, which keeps track of the allocated
array member, is not updated until the member allocation is
successfully finished, this could also lead to either use after free,
or uninitialized variable access in si_dpm_fini().
Fix this by postponing the free of the array until si_dpm_fini() and
increment adev->pm.dpm.num_ps everytime the array member is allocated.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2efb6359e ]
While running inside virtual machine, the kernel can bypass cache
flushing. Changing sleep state in a virtual machine doesn't affect the
host system sleep state and cannot lead to data loss.
Before entering sleep states, the ACPI code flushes caches to prevent
data loss using the WBINVD instruction. This mechanism is required on
bare metal.
But, any use WBINVD inside of a guest is worthless. Changing sleep
state in a virtual machine doesn't affect the host system sleep state
and cannot lead to data loss, so most hypervisors simply ignore it.
Despite this, the ACPI code calls WBINVD unconditionally anyway.
It's useless, but also normally harmless.
In TDX guests, though, WBINVD stops being harmless; it triggers a
virtualization exception (#VE). If the ACPI cache-flushing WBINVD
were left in place, TDX guests would need handling to recover from
the exception.
Avoid using WBINVD whenever running under a hypervisor. This both
removes the useless WBINVDs and saves TDX from implementing WBINVD
handling.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-30-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e12968f6d ]
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5321a0fa8 upstream.
The following error message lack the "0x" obviously:
cannot mount because of unsupported optional features (4000)
Add the prefix to make it less confusing. This can happen on older
kernels that try to mount a filesystem with newer features so it makes
sense to backport to older trees.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a2d90ba02 upstream.
The current implementation of PTRACE_KILL is buggy and has been for
many years as it assumes it's target has stopped in ptrace_stop. At a
quick skim it looks like this assumption has existed since ptrace
support was added in linux v1.0.
While PTRACE_KILL has been deprecated we can not remove it as
a quick search with google code search reveals many existing
programs calling it.
When the ptracee is not stopped at ptrace_stop some fields would be
set that are ignored except in ptrace_stop. Making the userspace
visible behavior of PTRACE_KILL a noop in those case.
As the usual rules are not obeyed it is not clear what the
consequences are of calling PTRACE_KILL on a running process.
Presumably userspace does not do this as it achieves nothing.
Replace the implementation of PTRACE_KILL with a simple
send_sig_info(SIGKILL) followed by a return 0. This changes the
observable user space behavior only in that PTRACE_KILL on a process
not stopped in ptrace_stop will also kill it. As that has always
been the intent of the code this seems like a reasonable change.
Cc: stable@vger.kernel.org
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lkml.kernel.org/r/20220505182645.497868-7-ebiederm@xmission.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce3c4ad7f4 upstream.
nfsd4_release_lockowner() holds clp->cl_lock when it calls
check_for_locks(). However, check_for_locks() calls nfsd_file_get()
/ nfsd_file_put() to access the backing inode's flc_posix list, and
nfsd_file_put() can sleep if the inode was recently removed.
Let's instead rely on the stateowner's reference count to gate
whether the release is permitted. This should be a reliable
indication of locks-in-use since file lock operations and
->lm_get_owner take appropriate references, which are released
appropriately when file locks are removed.
Reported-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4caae58406 upstream.
The device-mapper framework provides a mechanism to mark targets as
immutable (and hence fail table reloads that try to change the target
type). Add the DM_TARGET_IMMUTABLE flag to the dm-verity target's
feature flags to prevent switching the verity target with a different
target type.
Fixes: a4ffc15219 ("dm: add verity target")
Cc: stable@vger.kernel.org
Signed-off-by: Sarthak Kukreti <sarthakkukreti@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfe2b0146c upstream.
dm-stats can be used with a very large number of entries (it is only
limited by 1/4 of total system memory), so add rescheduling points to
the loops that iterate over the entries.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 567dd8f345 upstream.
The device mapper dm-crypt target is using scnprintf("%02x", cc->key[i]) to
report the current key to userspace. However, this is not a constant-time
operation and it may leak information about the key via timing, via cache
access patterns or via the branch predictor.
Change dm-crypt's key printing to use "%c" instead of "%02x". Also
introduce hex2asc() that carefully avoids any branching or memory
accesses when converting a number in the range 0 ... 15 to an ascii
character.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 336feb502a upstream.
Fix the following -Wstringop-overflow warnings when building with GCC-11:
drivers/gpu/drm/i915/intel_pm.c:3106:9: warning: ‘intel_read_wm_latency’ accessing 16 bytes in a region of size 10 [-Wstringop-overflow=]
3106 | intel_read_wm_latency(dev_priv, dev_priv->wm.pri_latency);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_pm.c:3106:9: note: referencing argument 2 of type ‘u16 *’ {aka ‘short unsigned int *’}
drivers/gpu/drm/i915/intel_pm.c:2861:13: note: in a call to function ‘intel_read_wm_latency’
2861 | static void intel_read_wm_latency(struct drm_i915_private *dev_priv,
| ^~~~~~~~~~~~~~~~~~~~~
by removing the over-specified array size from the argument declarations.
It seems that this code is actually safe because the size of the
array depends on the hardware generation, and the function checks
for that.
Notice that wm can be an array of 5 elements:
drivers/gpu/drm/i915/intel_pm.c:3109: intel_read_wm_latency(dev_priv, dev_priv->wm.pri_latency);
or an array of 8 elements:
drivers/gpu/drm/i915/intel_pm.c:3131: intel_read_wm_latency(dev_priv, dev_priv->wm.skl_latency);
and the compiler legitimately complains about that.
This helps with the ongoing efforts to globally enable
-Wstringop-overflow.
Link: https://github.com/KSPP/linux/issues/181
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1dc87763f upstream.
A rare BUG_ON triggered in assoc_array_gc:
[3430308.818153] kernel BUG at lib/assoc_array.c:1609!
Which corresponded to the statement currently at line 1593 upstream:
BUG_ON(assoc_array_ptr_is_meta(p));
Using the data from the core dump, I was able to generate a userspace
reproducer[1] and determine the cause of the bug.
[1]: https://github.com/brenns10/kernel_stuff/tree/master/assoc_array_gc
After running the iterator on the entire branch, an internal tree node
looked like the following:
NODE (nr_leaves_on_branch: 3)
SLOT [0] NODE (2 leaves)
SLOT [1] NODE (1 leaf)
SLOT [2..f] NODE (empty)
In the userspace reproducer, the pr_devel output when compressing this
node was:
-- compress node 0x5607cc089380 --
free=0, leaves=0
[0] retain node 2/1 [nx 0]
[1] fold node 1/1 [nx 0]
[2] fold node 0/1 [nx 2]
[3] fold node 0/2 [nx 2]
[4] fold node 0/3 [nx 2]
[5] fold node 0/4 [nx 2]
[6] fold node 0/5 [nx 2]
[7] fold node 0/6 [nx 2]
[8] fold node 0/7 [nx 2]
[9] fold node 0/8 [nx 2]
[10] fold node 0/9 [nx 2]
[11] fold node 0/10 [nx 2]
[12] fold node 0/11 [nx 2]
[13] fold node 0/12 [nx 2]
[14] fold node 0/13 [nx 2]
[15] fold node 0/14 [nx 2]
after: 3
At slot 0, an internal node with 2 leaves could not be folded into the
node, because there was only one available slot (slot 0). Thus, the
internal node was retained. At slot 1, the node had one leaf, and was
able to be folded in successfully. The remaining nodes had no leaves,
and so were removed. By the end of the compression stage, there were 14
free slots, and only 3 leaf nodes. The tree was ascended and then its
parent node was compressed. When this node was seen, it could not be
folded, due to the internal node it contained.
The invariant for compression in this function is: whenever
nr_leaves_on_branch < ASSOC_ARRAY_FAN_OUT, the node should contain all
leaf nodes. The compression step currently cannot guarantee this, given
the corner case shown above.
To fix this issue, retry compression whenever we have retained a node,
and yet nr_leaves_on_branch < ASSOC_ARRAY_FAN_OUT. This second
compression will then allow the node in slot 1 to be folded in,
satisfying the invariant. Below is the output of the reproducer once the
fix is applied:
-- compress node 0x560e9c562380 --
free=0, leaves=0
[0] retain node 2/1 [nx 0]
[1] fold node 1/1 [nx 0]
[2] fold node 0/1 [nx 2]
[3] fold node 0/2 [nx 2]
[4] fold node 0/3 [nx 2]
[5] fold node 0/4 [nx 2]
[6] fold node 0/5 [nx 2]
[7] fold node 0/6 [nx 2]
[8] fold node 0/7 [nx 2]
[9] fold node 0/8 [nx 2]
[10] fold node 0/9 [nx 2]
[11] fold node 0/10 [nx 2]
[12] fold node 0/11 [nx 2]
[13] fold node 0/12 [nx 2]
[14] fold node 0/13 [nx 2]
[15] fold node 0/14 [nx 2]
internal nodes remain despite enough space, retrying
-- compress node 0x560e9c562380 --
free=14, leaves=1
[0] fold node 2/15 [nx 0]
after: 3
Changes
=======
DH:
- Use false instead of 0.
- Reorder the inserted lines in a couple of places to put retained before
next_slot.
ver #2)
- Fix typo in pr_devel, correct comparison to "<="
Fixes: 3cb989501c ("Add a generic associative array implementation.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: keyrings@vger.kernel.org
Link: https://lore.kernel.org/r/20220511225517.407935-1-stephen.s.brennan@oracle.com/ # v1
Link: https://lore.kernel.org/r/20220512215045.489140-1-stephen.s.brennan@oracle.com/ # v2
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03a35bc856 ]
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015c44d7bf ]
Since the recent introduction supporting the SM3 and SM4 hash algos for IPsec, the kernel
produces invalid pfkey acquire messages, when these encryption modules are disabled. This
happens because the availability of the algos wasn't checked in all necessary functions.
This patch adds these checks.
Signed-off-by: Thomas Bartschies <thomas.bartschies@cvk.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26f9ce5381 ]
Aborting commands that have already been sent to the firmware can
cause BUG in qlt_free_cmd(): BUG_ON(cmd->sg_mapped)
For instance:
- Command passes rdx_to_xfer state, maps sgl, sends to the firmware
- Reset occurs, qla2xxx performs ISP error recovery, aborts the command
- Target stack calls qlt_abort_cmd() and then qlt_free_cmd()
- BUG_ON(cmd->sg_mapped) in qlt_free_cmd() occurs because sgl was not
unmapped
Thus, unmap sgl in qlt_abort_cmd() for commands with the aborted flag set.
Link: https://lore.kernel.org/r/AS8PR10MB4952D545F84B6B1DFD39EC1E9DEE9@AS8PR10MB4952.EURPRD10.PROD.OUTLOOK.COM
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Gleb Chesnokov <Chesnokov.G@raidix.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8ac1c4784 ]
The compilation on s390 results in this error:
# make DEBUG=y bench/numa.o
...
bench/numa.c: In function ‘__bench_numa’:
bench/numa.c:1749:81: error: ‘%d’ directive output may be truncated
writing between 1 and 11 bytes into a region of size between
10 and 20 [-Werror=format-truncation=]
1749 | snprintf(tname, sizeof(tname), "process%d:thread%d", p, t);
^~
...
bench/numa.c:1749:64: note: directive argument in the range
[-2147483647, 2147483646]
...
#
The maximum length of the %d replacement is 11 characters because of the
negative sign. Therefore extend the array by two more characters.
Output after:
# make DEBUG=y bench/numa.o > /dev/null 2>&1; ll bench/numa.o
-rw-r--r-- 1 root root 418320 May 19 09:11 bench/numa.o
#
Fixes: 3aff8ba0a4 ("perf bench numa: Avoid possible truncation when using snprintf()")
Suggested-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20220520081158.2990006-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942d2ad5d2 ]
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfb301997 ]
In Thumb2, 'b . + 4' produces a branch instruction that uses a narrow
encoding, and so it does not jump to the following instruction as
expected. So use W(b) instead.
Fixes: 6c7cb60bff ("ARM: fix Thumb2 regression with Spectre BHB")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc14aa94c ]
The Spectre-BHB mitigations were inadvertently left disabled for
Cortex-A15, due to the fact that cpu_v7_bugs_init() is not called in
that case. So fix that.
Fixes: b9baf5c8c5 ("ARM: Spectre-BHB workaround")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dc2a5a8f6 ]
If skb_clone() returns null pointer, pfkey_broadcast() will
return error.
Therefore, it should be better to check the return value of
pfkey_broadcast() and return error if fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23dd458135 ]
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
(interrupt context 1)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_skb_alloc(..., GFP_KERNEL) //may sleep
(interrupt context 2)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_send_data
nci_queue_tx_data_frags
nci_skb_alloc(..., GFP_KERNEL) //may sleep
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: ed06aeefda ("nfc: st-nci: Rename st21nfcb to st-nci")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5361448e45 ]
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
This has been spotted by smatch.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf410cb74 ]
In vmxnet3_rq_create(), when dma_alloc_coherent() fails,
vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then
vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all()
-> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls
vmxnet3_force_close() -> dev_close() in error handling code. And the driver
calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all()
-> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(),
rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing
a NULL pointer dereference.
To fix this possible bug, an if statement is added to check whether
rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so.
The error log in our fault-injection testing is shown as follows:
[ 65.220135] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 65.222633] RIP: 0010:vmxnet3_rq_cleanup_all+0x396/0x4e0 [vmxnet3]
...
[ 65.227977] Call Trace:
...
[ 65.228262] vmxnet3_quiesce_dev+0x80f/0x8a0 [vmxnet3]
[ 65.228580] vmxnet3_close+0x2c4/0x3f0 [vmxnet3]
[ 65.228866] __dev_close_many+0x288/0x350
[ 65.229607] dev_close_many+0xa4/0x480
[ 65.231124] dev_close+0x138/0x230
[ 65.231933] vmxnet3_force_close+0x1f0/0x240 [vmxnet3]
[ 65.232248] vmxnet3_change_mtu+0x75d/0x920 [vmxnet3]
...
Fixes: d1a890fa37 ("net: VMware virtual Ethernet NIC driver: vmxnet3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Zixuan Fu <r33s3n6@gmail.com>
Link: https://lore.kernel.org/r/20220514050711.2636709-1-r33s3n6@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3ac6487e58 upstream.
Norbert reported that it's possible to race sys_perf_event_open() such
that the looser ends up in another context from the group leader,
triggering many WARNs.
The move_group case checks for races against itself, but the
!move_group case doesn't, seemingly relying on the previous
group_leader->ctx == ctx check. However, that check is racy due to not
holding any locks at that time.
Therefore, re-check the result after acquiring locks and bailing
if they no longer match.
Additionally, clarify the not_move_group case from the
move_group-vs-move_group race.
Fixes: f63a8daa58 ("perf: Fix event->ctx locking")
Reported-by: Norbert Slusarek <nslusarek@gmx.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 533a6cfe08 upstream
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[kamal: Drop non-existent hunks in 4.9's __mmc_switch]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
