commit baf10564fb upstream.
kill_ioctx() used to have an explicit RCU delay between removing the
reference from ->ioctx_table and percpu_ref_kill() dropping the refcount.
At some point that delay had been removed, on the theory that
percpu_ref_kill() itself contained an RCU delay. Unfortunately, that was
the wrong kind of RCU delay and it didn't care about rcu_read_lock() used
by lookup_ioctx(). As the result, we could get ctx freed right under
lookup_ioctx(). Tejun has fixed that in a6d7cff472 ("fs/aio: Add explicit
RCU grace period when freeing kioctx"); however, that fix is not enough.
Suppose io_destroy() from one thread races with e.g. io_setup() from another;
CPU1 removes the reference from current->mm->ioctx_table[...] just as CPU2
has picked it (under rcu_read_lock()). Then CPU1 proceeds to drop the
refcount, getting it to 0 and triggering a call of free_ioctx_users(),
which proceeds to drop the secondary refcount and once that reaches zero
calls free_ioctx_reqs(). That does
INIT_RCU_WORK(&ctx->free_rwork, free_ioctx);
queue_rcu_work(system_wq, &ctx->free_rwork);
and schedules freeing the whole thing after RCU delay.
In the meanwhile CPU2 has gotten around to percpu_ref_get(), bumping the
refcount from 0 to 1 and returned the reference to io_setup().
Tejun's fix (that queue_rcu_work() in there) guarantees that ctx won't get
freed until after percpu_ref_get(). Sure, we'd increment the counter before
ctx can be freed. Now we are out of rcu_read_lock() and there's nothing to
stop freeing of the whole thing. Unfortunately, CPU2 assumes that since it
has grabbed the reference, ctx is *NOT* going away until it gets around to
dropping that reference.
The fix is obvious - use percpu_ref_tryget_live() and treat failure as miss.
It's not costlier than what we currently do in normal case, it's safe to
call since freeing *is* delayed and it closes the race window - either
lookup_ioctx() comes before percpu_ref_kill() (in which case ctx->users
won't reach 0 until the caller of lookup_ioctx() drops it) or lookup_ioctx()
fails, ctx->users is unaffected and caller of lookup_ioctx() doesn't see
the object in question at all.
Cc: stable@kernel.org
Fixes: a6d7cff472 "fs/aio: Add explicit RCU grace period when freeing kioctx"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79f546a696 upstream.
We recently had an oops reported on a 4.14 kernel in
xfs_reclaim_inodes_count() where sb->s_fs_info pointed to garbage
and so the m_perag_tree lookup walked into lala land. It produces
an oops down this path during the failed mount:
radix_tree_gang_lookup_tag+0xc4/0x130
xfs_perag_get_tag+0x37/0xf0
xfs_reclaim_inodes_count+0x32/0x40
xfs_fs_nr_cached_objects+0x11/0x20
super_cache_count+0x35/0xc0
shrink_slab.part.66+0xb1/0x370
shrink_node+0x7e/0x1a0
try_to_free_pages+0x199/0x470
__alloc_pages_slowpath+0x3a1/0xd20
__alloc_pages_nodemask+0x1c3/0x200
cache_grow_begin+0x20b/0x2e0
fallback_alloc+0x160/0x200
kmem_cache_alloc+0x111/0x4e0
The problem is that the superblock shrinker is running before the
filesystem structures it depends on have been fully set up. i.e.
the shrinker is registered in sget(), before ->fill_super() has been
called, and the shrinker can call into the filesystem before
fill_super() does it's setup work. Essentially we are exposed to
both use-after-free and use-before-initialisation bugs here.
To fix this, add a check for the SB_BORN flag in super_cache_count.
In general, this flag is not set until ->fs_mount() completes
successfully, so we know that it is set after the filesystem
setup has completed. This matches the trylock_super() behaviour
which will not let super_cache_scan() run if SB_BORN is not set, and
hence will not allow the superblock shrinker from entering the
filesystem while it is being set up or after it has failed setup
and is being torn down.
Cc: stable@kernel.org
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30da870ce4 upstream.
we unlock the directory hash too early - if we are looking at secondary
link and primary (in another directory) gets removed just as we unlock,
we could have the old primary moved in place of the secondary, leaving
us to look into freed entry (and leaving our dentry with ->d_fsdata
pointing to a freed entry).
Cc: stable@vger.kernel.org # 2.4.4+
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a3a92ccfe upstream.
Check the TIF_32BIT_FPREGS task setting of the tracee rather than the
tracer in determining the layout of floating-point general registers in
the floating-point context, correcting access to odd-numbered registers
for o32 tracees where the setting disagrees between the two processes.
Fixes: 597ce1723e ("MIPS: Support for 64-bit FP with O32 binaries")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71e909c0cd upstream.
Correct commit 7aeb753b53 ("MIPS: Implement task_user_regset_view.")
and expose the FIR register using the unused 4 bytes at the end of the
NT_PRFPREG regset. Without that register included clients cannot use
the PTRACE_GETREGSET request to retrieve the complete FPU register set
and have to resort to one of the older interfaces, either PTRACE_PEEKUSR
or PTRACE_GETFPREGS, to retrieve the missing piece of data. Also the
register is irreversibly missing from core dumps.
This register is architecturally hardwired and read-only so the write
path does not matter. Ignore data supplied on writes then.
Fixes: 7aeb753b53 ("MIPS: Implement task_user_regset_view.")
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.13+
Patchwork: https://patchwork.linux-mips.org/patch/19273/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55a2aa08b3 upstream.
When DMA will be performed to a MIPS32 1004K CPS, the L1-cache for the
range needs to be flushed and invalidated first.
The code currently takes one of two approaches.
1/ If the range is less than the size of the dcache, then HIT type
requests flush/invalidate cache lines for the particular addresses.
HIT-type requests a globalised by the CPS so this is safe on SMP.
2/ If the range is larger than the size of dcache, then INDEX type
requests flush/invalidate the whole cache. INDEX type requests affect
the local cache only. CPS does not propagate them in any way. So this
invalidation is not safe on SMP CPS systems.
Data corruption due to '2' can quite easily be demonstrated by
repeatedly "echo 3 > /proc/sys/vm/drop_caches" and then sha1sum a file
that is several times the size of available memory. Dropping caches
means that large contiguous extents (large than dcache) are more likely.
This was not a problem before Linux-4.8 because option 2 was never used
if CONFIG_MIPS_CPS was defined. The commit which removed that apparently
didn't appreciate the full consequence of the change.
We could, in theory, globalize the INDEX based flush by sending an IPI
to other cores. These cache invalidation routines can be called with
interrupts disabled and synchronous IPI require interrupts to be
enabled. Asynchronous IPI may not trigger writeback soon enough. So we
cannot use IPI in practice.
We can already test if IPI would be needed for an INDEX operation with
r4k_op_needs_ipi(R4K_INDEX). If this is true then we mustn't try the
INDEX approach as we cannot use IPI. If this is false (e.g. when there
is only one core and hence one L1 cache) then it is safe to use the
INDEX approach without IPI.
This patch avoids options 2 if r4k_op_needs_ipi(R4K_INDEX), and so
eliminates the corruption.
Fixes: c00ab4896e ("MIPS: Remove cpu_has_safe_index_cacheops")
Signed-off-by: NeilBrown <neil@brown.name>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.8+
Patchwork: https://patchwork.linux-mips.org/patch/19259/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bcdd559268 ]
The probe function is not allowed to fail after registering the RTC because
the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Switch to devm_rtc_allocate_device/rtc_register_device to register the rtc
as late as possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 347876ad47 ]
The shifting of buf[5] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. If
the top bit of buf[5] is set then all then all the upper bits sec
end up as also being set because of the sign-extension. Fix this by
casting buf[5] to an unsigned long before the shift.
Detected by CoverityScan, CID#1465292 ("Unintended sign extension")
Fixes: 0e1492330c ("rtc: add rtc-tx4939 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 201fac95e7 ]
The probe function is not allowed to fail after registering the RTC because
the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Switch to devm_rtc_allocate_device/rtc_register_device to register the rtc
as late as possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b3a5ac42ab ]
On 32bit platforms, time_t is still a signed 32bit long. If it is
overflowed, userspace and the kernel cant agree on the current system time.
This causes multiple issues, in particular with systemd:
https://github.com/systemd/systemd/issues/1143
A good workaround is to simply avoid using hctosys which is something I
greatly encourage as the time is better set by userspace.
However, many distribution enable it and use systemd which is rendering the
system unusable in case the RTC holds a date after 2038 (and more so after
2106). Many drivers have workaround for this case and they should be
eliminated so there is only one place left to fix when userspace is able to
cope with dates after the 31bit overflow.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1485991c02 ]
commit 179a502f8c ("rtc: snvs: add Freescale rtc-snvs driver") introduces
the SNVS RTC driver with a function snvs_rtc_enable().
snvs_rtc_enable() can return an error on the enable path however this
driver does not currently trap that failure on the probe() path and
consequently if enabling the RTC fails we encounter a later error spinning
forever in rtc_write_sync_lp().
[ 36.093481] [<c010d630>] (__irq_svc) from [<c0c2e9ec>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 36.102122] [<c0c2e9ec>] (_raw_spin_unlock_irqrestore) from [<c072e32c>] (regmap_read+0x4c/0x5c)
[ 36.110938] [<c072e32c>] (regmap_read) from [<c085d0f4>] (rtc_write_sync_lp+0x6c/0x98)
[ 36.118881] [<c085d0f4>] (rtc_write_sync_lp) from [<c085d160>] (snvs_rtc_alarm_irq_enable+0x40/0x4c)
[ 36.128041] [<c085d160>] (snvs_rtc_alarm_irq_enable) from [<c08567b4>] (rtc_timer_do_work+0xd8/0x1a8)
[ 36.137291] [<c08567b4>] (rtc_timer_do_work) from [<c01441b8>] (process_one_work+0x28c/0x76c)
[ 36.145840] [<c01441b8>] (process_one_work) from [<c01446cc>] (worker_thread+0x34/0x58c)
[ 36.153961] [<c01446cc>] (worker_thread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.161388] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
[ 36.168635] rcu_sched kthread starved for 2602 jiffies! g496 c495 f0x2 RCU_GP_WAIT_FQS(3) ->state=0x0 ->cpu=0
[ 36.178564] rcu_sched R running task 0 8 2 0x00000000
[ 36.185664] [<c0c288b0>] (__schedule) from [<c0c29134>] (schedule+0x3c/0xa0)
[ 36.192739] [<c0c29134>] (schedule) from [<c0c2db80>] (schedule_timeout+0x78/0x4e0)
[ 36.200422] [<c0c2db80>] (schedule_timeout) from [<c01a7ab0>] (rcu_gp_kthread+0x648/0x1864)
[ 36.208800] [<c01a7ab0>] (rcu_gp_kthread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.216309] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
This patch fixes by parsing the result of rtc_write_sync_lp() and
propagating both in the probe and elsewhere. If the RTC doesn't start we
don't proceed loading the driver and don't get into this loop mess later
on.
Fixes: 179a502f8c ("rtc: snvs: add Freescale rtc-snvs driver")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e254963b6 ]
Most register accesses in the altera driver honor port->regshift by
using altera_uart_writel(). There are a few accesses however that were
missed when the driver was converted to use port->regshift and some
others were added later in commit 4d9d7d896d ("serial: altera_uart:
add earlycon support").
Fixes: 2780ad42f5 ("tty: serial: altera_uart: Use port->regshift to store bus shift")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e9fe53910 ]
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9f5786987 ]
The arc_uart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a
legitimate DTB.
Fixes: ea28fd56fc ("serial/arc-uart: switch to devicetree based probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffab87fdec ]
The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5673444821 ]
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd345a31bf ]
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 1ea6607d4c ("serial: mxs-auart: Allow device tree probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49ee23b718 ]
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes: 13a9f6c64f ("serial: samsung: Consider DT alias when probing ports")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 090fa4b0dc ]
The sci_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SH_SCI_NR_UARTS), so this can even be triggered using a
legitimate DTB.
Fixes: 97ed9790c5 ("serial: sh-sci: Remove unused platform data capabilities field")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7d75e18d0 ]
The cdns_uart_port[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 928e926349 ("tty: xuartps: Initialize ports according to aliases")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67300abdbe ]
Currently an out of range dev->nr is detected by just reporting the
issue and later on an out-of-bounds read on array card occurs because
of this. Fix this by checking the upper range of dev->nr with the size
of array card (removes the hard coded size), move this check earlier
and also exit with the error -ENOSYS to avoid the later out-of-bounds
array read.
Detected by CoverityScan, CID#711191 ("Out-of-bounds-read")
Fixes: commit 02b20b0b4c ("V4L/DVB (12730): Add conexant cx25821 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: %ld -> %zd]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65243386f4 ]
The vivid driver has two custom controls that change the behavior of RDS.
Depending on the control setting the V4L2_CAP_READWRITE capability is toggled.
However, after an earlier commit the capability was no longer set correctly.
This is now fixed.
Fixes: 9765a32cd8 ("vivid: set device_caps in video_device")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d13a0139d7 ]
Fixes vb2_vmalloc_get_userptr() to ioremap correct area.
Since the current code does ioremap the page address, if the offset > 0,
it does not do ioremap the last page and results in kernel panic.
This fixes to pass the size + offset to ioremap so that ioremap
can map correct area. Also, this uses __pfn_to_phys() to get the physical
address of given PFN.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Takao Orito <orito.takao@socionext.com>
Reported-by: Fumihiro ATSUMI <atsumi@infinitegra.co.jp>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f564184e6 ]
The ADV748x handles interlaced media using V4L2_FIELD_ALTERNATE field
types. The correct specification for the height on the mbus is the
image height, in this instance, the field height.
The AFE component already correctly adjusts the height on the mbus, but
the HDMI component got left behind.
Adjust the mbus height to correctly describe the image height of the
fields when processing interlaced video for HDMI pipelines.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94448e21cf ]
Both lgdt33606a_release and lgdt3306a_remove kfree state, but _release is
called first, then _remove operates on states members before kfree'ing it.
This can lead to random oops/GPF/etc on USB disconnect.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a398e04363 ]
While experimenting with older compiler versions, I ran
into a warning that no longer shows up on gcc-4.8 or newer:
drivers/media/platform/s3c-camif/camif-capture.c: In function '__camif_subdev_try_format':
drivers/media/platform/s3c-camif/camif-capture.c:1265:25: error: array subscript is below array bounds
This is an off-by-one bug, leading to an access before the start of the
array, while newer compilers silently assume this undefined behavior
cannot happen and leave the loop at index 0 if no other entry matches.
As Sylvester explains, we actually need to ensure that the
value is within the range, so this reworks the loop to be
easier to parse correctly, and an additional check to fall
back on the first format value for any unexpected input.
I found an existing gcc bug for it and added a reduced version
of the function there.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69249#c3
Fixes: babde1c243 ("[media] V4L: Add driver for S3C24XX/S3C64XX SoC series camera interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ceade1d97 ]
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 779c79d4b8 ]
Hauppauge produced a revision of ImpactVCBe using an 888,
with a 25MHz crystal, instead of using the default third
overtone 50Mhz crystal. This overrides that frequency so
that the cx25840 is properly configured. Without the proper
crystal setup the cx25840 cannot load the firmware or
decode video.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dd6b560dc ]
As pointed by Dan, possible values for bits[3:0] of te Line Mode Registers
can range from 0x0 to 0xf, but the check logic allow values ranging
from 0x0 to 0xe.
As static arrays are initialized with zero, using a value without
an explicit initializer at the array won't cause any harm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a145f64c61 ]
Returning -EINVAL when an ioctl is not implemented is a very
bad idea, as it is hard to distinguish from other error
contitions that an ioctl could lead. Replace it by its
right error code: -ENOTTY.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8321e7887 ]
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ac051eeab ]
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab0447845c ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cdb68fbd4e ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e4db0c283 ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 179db533c0 ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4bf59902b5 ]
The MMC sample and drv clock for rockchip platforms are derived from
the bus clock output to the MMC/SDIO card. So it should never happens
that the clk rate is zero given it should inherits the clock rate from
its parent. If something goes wrong and makes the clock rate to be zero,
the calculation would be wrong but may still make the mmc tuning process
work luckily. However it makes people harder to debug when the following
data transfer is unstable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c35b518f9b ]
Turns out latest upstream U-Boot does not configure/enable pll_u which
leaves it at some default rate of 500 kHz:
root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
pll_u 3 3 0 500000 0
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df934cbcbf ]
The symbol is in the __initconst section but not marked init, which
caused a warning when building with LTO.
This makes it 'const' as was obviously intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c80dfd9bf5 ("clk: hisilicon: add CRG driver for Hi3516CV300 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f9c63e8de ]
It's found that the clock phase output from clk_summary is
wrong compared to the actual phase reading from the register.
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 -22
It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.
When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b0556a441 ]
commit c420c1e4db ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 647d04f8e0 ]
If the RCLK mux clock configuration is specified in DT and no set_sysclk()
callback is used in the sound card driver the sclk_srcrate field will remain
set to 0, leading to an incorrect PSR divider setting.
To fix this the frequency value is retrieved from the CLK_I2S_RCLK_SRC clock,
so the actual RCLK mux selection is taken into account.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bde8b3887a ]
This patch adds the change required to create the TLV data
for dapm widget kcontrols from topology. This also fixes the following
TLV read error shown in amixer while showing the card control contents.
"amixer: Control hw:1 element TLV read error: No such device or address"
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
