commit 82e2c39f9e upstream.
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Cc: stable@vger.kernel.org
Fixes: 736b25afe2 ("net: dp83869: Add RGMII internal delay configuration")
Co-developed-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323102536.31988-1-josua@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05310f31ca upstream.
Fix xenvif_get_requests() not to do grant copy operations across local
page boundaries. This requires to double the maximum number of copy
operations per queue, as each copy could now be split into 2.
Make sure that struct xenvif_tx_cb doesn't grow too large.
Cc: stable@vger.kernel.org
Fixes: ad7f402ae4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0432bab6 upstream.
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 179a88a855 upstream.
When compiled with CONFIG_CIFS_DFS_UPCALL disabled, cifs_dfs_d_automount
is NULL. cifs.ko logic for mapping CIFS_FATTR_DFS_REFERRAL attributes to
S_AUTOMOUNT and corresponding dentry flags is retained regardless of
CONFIG_CIFS_DFS_UPCALL, leading to a NULL pointer dereference in
VFS follow_automount() when traversing a DFS referral link:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
<TASK>
__traverse_mounts+0xb5/0x220
? cifs_revalidate_mapping+0x65/0xc0 [cifs]
step_into+0x195/0x610
? lookup_fast+0xe2/0xf0
path_lookupat+0x64/0x140
filename_lookup+0xc2/0x140
? __create_object+0x299/0x380
? kmem_cache_alloc+0x119/0x220
? user_path_at_empty+0x31/0x50
user_path_at_empty+0x31/0x50
__x64_sys_chdir+0x2a/0xd0
? exit_to_user_mode_prepare+0xca/0x100
do_syscall_64+0x42/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
This fix adds an inline cifs_dfs_d_automount() {return -EREMOTE} handler
when CONFIG_CIFS_DFS_UPCALL is disabled. An alternative would be to
avoid flagging S_AUTOMOUNT, etc. without CONFIG_CIFS_DFS_UPCALL. This
approach was chosen as it provides more control over the error path.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09ba47b44d upstream.
We can't call smb_init() in CIFSGetDFSRefer() as cifs_reconnect_tcon()
may end up calling CIFSGetDFSRefer() again to get new DFS referrals
and thus causing an infinite recursion.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Cc: stable@vger.kernel.org # 6.2
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754ff5060d upstream.
The AlpsPS/2 code previously relied on the assumption that `char` is a
signed type, which was true on x86 platforms (the only place where this
driver is used) before kernel 6.2. However, on 6.2 and later, this
assumption is broken due to the introduction of -funsigned-char as a new
global compiler flag.
Fix this by explicitly specifying the signedness of `char` when sign
extending the values received from the device.
Fixes: f3f33c6776 ("Input: alps - Rushmore and v7 resolution support")
Signed-off-by: msizanoen <msizanoen@qtmlabs.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230320045228.182259-1-msizanoen@qtmlabs.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 657fd9da2d ]
In case the driver was trying to set an alternate mode for gpio
0 or 32 then the mode was not set correctly. The reason is that
there is computation error inside the function ocelot_pinmux_set_mux
because in this case it was trying to shift to left by -1.
Fix this by actually shifting the function bits and not the position.
Fixes: 4b36082e2e ("pinctrl: ocelot: fix pinmuxing for pins after 31")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230206203720.1177718-1-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 581bce7bcb ]
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c75dc94f2 ]
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Fixes: 9dd441e4ed ("soc: qcom: ipa: GSI transactions")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7daaeedb4 ]
PCI YMFPCI driver code contains lots of assignments in if condition,
which is a bad coding style that may confuse readers and occasionally
lead to bugs.
This patch is merely for coding-style fixes, no functional changes.
Link: https://lore.kernel.org/r/20210608140540.17885-53-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 6be2e7522e ("ALSA: ymfpci: Fix BUG_ON in probe function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f8cf76758 ]
The device release callback function invoked to release the matrix device
uses the dev_get_drvdata(device *dev) function to retrieve the
pointer to the vfio_matrix_dev object in order to free its storage. The
problem is, this object is not stored as drvdata with the device; since the
kfree function will accept a NULL pointer, the memory for the
vfio_matrix_dev object is never freed.
Since the device being released is contained within the vfio_matrix_dev
object, the container_of macro will be used to retrieve its pointer.
Fixes: 1fde573413 ("s390: vfio-ap: base implementation of VFIO AP device driver")
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230320150447.34557-1-akrowiak@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b4c99f7d9 ]
Syzkaller reported the following issue:
=====================================================
BUG: KMSAN: uninit-value in aio_rw_done fs/aio.c:1520 [inline]
BUG: KMSAN: uninit-value in aio_write+0x899/0x950 fs/aio.c:1600
aio_rw_done fs/aio.c:1520 [inline]
aio_write+0x899/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc+0x11d/0x3b0 mm/slab_common.c:981
kmalloc_array include/linux/slab.h:636 [inline]
bcm_tx_setup+0x80e/0x29d0 net/can/bcm.c:930
bcm_sendmsg+0x3a2/0xce0 net/can/bcm.c:1351
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
sock_write_iter+0x495/0x5e0 net/socket.c:1108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
CPU: 1 PID: 5034 Comm: syz-executor350 Not tainted 6.2.0-rc6-syzkaller-80422-geda666ff2276 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
=====================================================
We can follow the call chain and find that 'bcm_tx_setup' function
calls 'memcpy_from_msg' to copy some content to the newly allocated
frame of 'op->frames'. After that the 'len' field of copied structure
being compared with some constant value (64 or 8). However, if
'memcpy_from_msg' returns an error, we will compare some uninitialized
memory. This triggers 'uninit-value' issue.
This patch will add 'memcpy_from_msg' possible errors processing to
avoid uninit-value issue.
Tested via syzkaller
Reported-by: syzbot+c9bfd85eca611ebf5db1@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=47f897f8ad958bbde5790ebf389b5e7e0a345089
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Fixes: 6f3b911d5f ("can: bcm: add support for CAN FD frames")
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230314120445.12407-1-ivan.orlov0322@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7602e7332 ]
The blamed commit has introduced the following tests to
dwmac4_add_hw_vlan_rx_fltr(), called from stmmac_vlan_rx_add_vid():
if (hw->promisc) {
netdev_err(dev,
"Adding VLAN in promisc mode not supported\n");
return -EPERM;
}
"VLAN promiscuous" mode is keyed in this driver to IFF_PROMISC, and so,
vlan_vid_add() and vlan_vid_del() calls cannot take place in IFF_PROMISC
mode. I have the following 2 arguments that this restriction is.... hm,
how shall I put it nicely... unproductive :)
First, take the case of a Linux bridge. If the kernel is compiled with
CONFIG_BRIDGE_VLAN_FILTERING=y, then this bridge shall have a VLAN
database. The bridge shall try to call vlan_add_vid() on its bridge
ports for each VLAN in the VLAN table. It will do this irrespectively of
whether that port is *currently* VLAN-aware or not. So it will do this
even when the bridge was created with vlan_filtering 0.
But the Linux bridge, in VLAN-unaware mode, configures its ports in
promiscuous (IFF_PROMISC) mode, so that they accept packets with any
MAC DA (a switch must do this in order to forward those packets which
are not directly targeted to its MAC address).
As a result, the stmmac driver does not work as a bridge port, when the
kernel is compiled with CONFIG_BRIDGE_VLAN_FILTERING=y.
$ ip link add br0 type bridge && ip link set br0 up
$ ip link set eth0 master br0 && ip link set eth0 up
[ 2333.943296] br0: port 1(eth0) entered blocking state
[ 2333.943381] br0: port 1(eth0) entered disabled state
[ 2333.943782] device eth0 entered promiscuous mode
[ 2333.944080] 4033c000.ethernet eth0: Adding VLAN in promisc mode not supported
[ 2333.976509] 4033c000.ethernet eth0: failed to initialize vlan filtering on this port
RTNETLINK answers: Operation not permitted
Secondly, take the case of stmmac as DSA master. Some switch tagging
protocols are based on 802.1Q VLANs (tag_sja1105.c), and as such,
tag_8021q.c uses vlan_vid_add() to work with VLAN-filtering DSA masters.
But also, when a DSA port becomes promiscuous (for example when it joins
a bridge), the DSA framework also makes the DSA master promiscuous.
Moreover, for every VLAN that a DSA switch sends to the CPU, DSA also
programs a VLAN filter on the DSA master, because if the the DSA switch
uses a tail tag, then the hardware frame parser of the DSA master will
see VLAN as VLAN, and might filter them out, for being unknown.
Due to the above 2 reasons, my belief is that the stmmac driver does not
get to choose to not accept vlan_vid_add() calls while IFF_PROMISC is
enabled, because the 2 are completely independent and there are code
paths in the network stack which directly lead to this situation
occurring, without the user's direct input.
In fact, my belief is that "VLAN promiscuous" mode should have never
been keyed on IFF_PROMISC in the first place, but rather, on the
NETIF_F_HW_VLAN_CTAG_FILTER feature flag which can be toggled by the
user through ethtool -k, when present in netdev->hw_features.
In the stmmac driver, NETIF_F_HW_VLAN_CTAG_FILTER is only present in
"features", making this feature "on [fixed]".
I have this belief because I am unaware of any definition of promiscuity
which implies having an effect on anything other than MAC DA (therefore
not VLAN). However, I seem to be rather alone in having this opinion,
looking back at the disagreements from this discussion:
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
In any case, to remove the vlan_vid_add() dependency on !IFF_PROMISC,
one would need to remove the check and see what fails. I guess the test
was there because of the way in which dwmac4_vlan_promisc_enable() is
implemented.
For context, the dwmac4 supports Perfect Filtering for a limited number
of VLANs - dwmac4_get_num_vlan(), priv->hw->num_vlan, with a fallback on
Hash Filtering - priv->dma_cap.vlhash - see stmmac_vlan_update(), also
visible in cat /sys/kernel/debug/stmmaceth/eth0/dma_cap | grep 'VLAN
Hash Filtering'.
The perfect filtering is based on MAC_VLAN_Tag_Filter/MAC_VLAN_Tag_Data
registers, accessed in the driver through dwmac4_write_vlan_filter().
The hash filtering is based on the MAC_VLAN_Hash_Table register, named
GMAC_VLAN_HASH_TABLE in the driver and accessed by dwmac4_update_vlan_hash().
The control bit for enabling hash filtering is GMAC_VLAN_VTHM
(MAC_VLAN_Tag_Ctrl bit VTHM: VLAN Tag Hash Table Match Enable).
Now, the description of dwmac4_vlan_promisc_enable() is that it iterates
through the driver's cache of perfect filter entries (hw->vlan_filter[i],
added by dwmac4_add_hw_vlan_rx_fltr()), and evicts them from hardware by
unsetting their GMAC_VLAN_TAG_DATA_VEN (MAC_VLAN_Tag_Data bit VEN - VLAN
Tag Enable) bit. Then it unsets the GMAC_VLAN_VTHM bit, which disables
hash matching.
This leaves the MAC, according to table "VLAN Match Status" from the
documentation, to always enter these data paths:
VID |VLAN Perfect Filter |VTHM Bit |VLAN Hash Filter |Final VLAN Match
|Match Result | |Match Result |Status
-------|--------------------|---------|-----------------|----------------
VID!=0 |Fail |0 |don't care |Pass
So, dwmac4_vlan_promisc_enable() does its job, but by unsetting
GMAC_VLAN_VTHM, it conflicts with the other code path which controls
this bit: dwmac4_update_vlan_hash(), called through stmmac_update_vlan_hash()
from stmmac_vlan_rx_add_vid() and from stmmac_vlan_rx_kill_vid().
This is, I guess, why dwmac4_add_hw_vlan_rx_fltr() is not allowed to run
after dwmac4_vlan_promisc_enable() has unset GMAC_VLAN_VTHM: because if
it did, then dwmac4_update_vlan_hash() would set GMAC_VLAN_VTHM again,
breaking the "VLAN promiscuity".
It turns out that dwmac4_vlan_promisc_enable() is way too complicated
for what needs to be done. The MAC_Packet_Filter register also has the
VTFE bit (VLAN Tag Filter Enable), which simply controls whether VLAN
tagged packets which don't match the filtering tables (either perfect or
hash) are dropped or not. At the moment, this driver unconditionally
sets GMAC_PACKET_FILTER_VTFE if NETIF_F_HW_VLAN_CTAG_FILTER was detected
through the priv->dma_cap.vlhash capability bits of the device, in
stmmac_dvr_probe().
I would suggest deleting the unnecessarily complex logic from
dwmac4_vlan_promisc_enable(), and simply unsetting GMAC_PACKET_FILTER_VTFE
when becoming IFF_PROMISC, which has the same effect of allowing packets
with any VLAN tags, but has the additional benefit of being able to run
concurrently with stmmac_vlan_rx_add_vid() and stmmac_vlan_rx_kill_vid().
As much as I believe that the VTFE bit should have been exclusively
controlled by NETIF_F_HW_VLAN_CTAG_FILTER through ethtool, and not by
IFF_PROMISC, changing that is not a punctual fix to the problem, and it
would probably break the VFFQ feature added by the later commit
e0f9956a38 ("net: stmmac: Add option for VLAN filter fail queue
enable"). From the commit description, VFFQ needs IFF_PROMISC=on and
VTFE=off in order to work (and this change respects that). But if VTFE
was changed to be controlled through ethtool -k, then a user-visible
change would have been introduced in Intel's scripts (a need to run
"ethtool -k eth0 rx-vlan-filter off" which did not exist before).
The patch was tested with this set of commands:
ip link set eth0 up
ip link add link eth0 name eth0.100 type vlan id 100
ip addr add 192.168.100.2/24 dev eth0.100 && ip link set eth0.100 up
ip link set eth0 promisc on
ip link add link eth0 name eth0.101 type vlan id 101
ip addr add 192.168.101.2/24 dev eth0.101 && ip link set eth0.101 up
ip link set eth0 promisc off
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link set eth0 promisc on
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link del eth0.100
ip link del eth0.101
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we should see them
ip link set eth0 promisc off
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we shouldn't see them
# anymore, but remove the "-p" argument from tcpdump and they're there.
Fixes: c89f44ff10 ("net: stmmac: Add support for VLAN promiscuous mode")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3cbdcb0fb ]
The failover txq is inited as 16 queues.
when a packet is transmitted from the failover device firstly,
the failover device will select the queue which is returned from
the primary device if the primary device is UP and running.
If the primary device txq is bigger than the default 16,
it can lead to the following warning:
eth0 selects TX queue 18, but real number of TX queues is 16
The warning backtrace is:
[ 32.146376] CPU: 18 PID: 9134 Comm: chronyd Tainted: G E 6.2.8-1.el7.centos.x86_64 #1
[ 32.147175] Hardware name: Red Hat KVM, BIOS 1.10.2-3.el7_4.1 04/01/2014
[ 32.147730] Call Trace:
[ 32.147971] <TASK>
[ 32.148183] dump_stack_lvl+0x48/0x70
[ 32.148514] dump_stack+0x10/0x20
[ 32.148820] netdev_core_pick_tx+0xb1/0xe0
[ 32.149180] __dev_queue_xmit+0x529/0xcf0
[ 32.149533] ? __check_object_size.part.0+0x21c/0x2c0
[ 32.149967] ip_finish_output2+0x278/0x560
[ 32.150327] __ip_finish_output+0x1fe/0x2f0
[ 32.150690] ip_finish_output+0x2a/0xd0
[ 32.151032] ip_output+0x7a/0x110
[ 32.151337] ? __pfx_ip_finish_output+0x10/0x10
[ 32.151733] ip_local_out+0x5e/0x70
[ 32.152054] ip_send_skb+0x19/0x50
[ 32.152366] udp_send_skb.isra.0+0x163/0x3a0
[ 32.152736] udp_sendmsg+0xba8/0xec0
[ 32.153060] ? __folio_memcg_unlock+0x25/0x60
[ 32.153445] ? __pfx_ip_generic_getfrag+0x10/0x10
[ 32.153854] ? sock_has_perm+0x85/0xa0
[ 32.154190] inet_sendmsg+0x6d/0x80
[ 32.154508] ? inet_sendmsg+0x6d/0x80
[ 32.154838] sock_sendmsg+0x62/0x70
[ 32.155152] ____sys_sendmsg+0x134/0x290
[ 32.155499] ___sys_sendmsg+0x81/0xc0
[ 32.155828] ? _get_random_bytes.part.0+0x79/0x1a0
[ 32.156240] ? ip4_datagram_release_cb+0x5f/0x1e0
[ 32.156649] ? get_random_u16+0x69/0xf0
[ 32.156989] ? __fget_light+0xcf/0x110
[ 32.157326] __sys_sendmmsg+0xc4/0x210
[ 32.157657] ? __sys_connect+0xb7/0xe0
[ 32.157995] ? __audit_syscall_entry+0xce/0x140
[ 32.158388] ? syscall_trace_enter.isra.0+0x12c/0x1a0
[ 32.158820] __x64_sys_sendmmsg+0x24/0x30
[ 32.159171] do_syscall_64+0x38/0x90
[ 32.159493] entry_SYSCALL_64_after_hwframe+0x72/0xdc
Fix that by reducing txq number as the non-existent primary-dev does.
Fixes: cfc80d9a11 ("net: Introduce net_failover driver")
Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33189f0a94 ]
When link speed is 10 Mbps and temperature is under -20°C, RTL8168H and
RTL8107E may have rx crc error. Disable phy 10 Mbps pll off to fix this
issue.
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f33642224e ]
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable.
Fixes: 7f4399ba40 ("ptp_qoriq: fix NULL access if ptp dt node missing")
Signed-off-by: SongJingyi <u201912584@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230324031406.1895159-1-u201912584@hust.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca4a80e4bb ]
At NIC reset, some offload features related to encapsulated traffic
might have changed (this mainly happens if the firmware-variant is
changed with the sfboot userspace tool). Because of this, features are
checked and set again at reset time.
However, this was not done right, and some features were improperly
overwritten at NIC reset:
- Tunneled IPv6 segmentation was always disabled
- Features disabled with ethtool were reenabled
- Features that becomes unsupported after the reset were not disabled
Also, checking if the device supports IPV6_CSUM to enable TSO6 is no
longer necessary because all currently supported devices support it.
Additionally, move the assignment of some other features to the
EF10_OFFLOAD_FEATURES macro, like it is done in ef100, leaving the
selection of features in efx_pci_probe_post_io a bit cleaner.
Fixes: ffffd2454a ("sfc: correctly advertise tunneled IPv6 segmentation")
Fixes: 24b2c3751a ("sfc: advertise encapsulated offloads on EF10")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Suggested-by: Jonathan Cooper <jonathan.s.cooper@amd.com>
Tested-by: Jonathan Cooper <jonathan.s.cooper@amd.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230323083417.7345-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40aafc7d58 ]
When running as non-root the following error is seen in turbostat:
turbostat: fopen /dev/cpu_dma_latency
: Permission denied
turbostat and the man page have information on how to avoid other
permission errors, so these can be fixed the same way.
Provide better /dev/cpu_dma_latency warnings that provide instructions on
how to avoid the error, and update the man page.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44a3b36b42 ]
var->pixclock can be assigned to zero by user. Without
proper check, divide by zero would occur when invoking
macro PICOS2KHZ in au1200fb_fb_check_var.
Error out if var->pixclock is zero.
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61ac4b86a4 ]
var->pixclock can be assigned to zero by user. Without proper
check, divide by zero would occur in lx_set_clock.
Error out if var->pixclock is zero.
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d823685486 ]
Variable var->pixclock is controlled by user and can be assigned
to zero. Without proper check, divide by zero would occur in
intelfbhw_validate_mode and intelfbhw_mode_to_hw.
Error out if var->pixclock is zero.
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e2a00f29 ]
variable var->pixclock can be set by user. In case it
equals to zero, divide by zero would occur in nvidiafb_set_par.
Similar crashes have happened in other fbdev drivers. There
is no check and modification on var->pixclock along the call
chain to nvidia_check_var and nvidiafb_set_par. We believe it
could also be triggered in driver nvidia from user site.
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6015b1aca1 ]
The getaffinity() system call uses 'cpumask_size()' to decide how big
the CPU mask is - so far so good. It is indeed the allocation size of a
cpumask.
But the code also assumes that the whole allocation is initialized
without actually doing so itself. That's wrong, because we might have
fixed-size allocations (making copying and clearing more efficient), but
not all of it is then necessarily used if 'nr_cpu_ids' is smaller.
Having checked other users of 'cpumask_size()', they all seem to be ok,
either using it purely for the allocation size, or explicitly zeroing
the cpumask before using the size in bytes to copy it.
See for example the ublk_ctrl_get_queue_affinity() function that uses
the proper 'zalloc_cpumask_var()' to make sure that the whole mask is
cleared, whether the storage is on the stack or if it was an external
allocation.
Fix this by just zeroing the allocation before using it. Do the same
for the compat version of sched_getaffinity(), which had the same logic.
Also, for consistency, make sched_getaffinity() use 'cpumask_bits()' to
access the bits. For a cpumask_var_t, it ends up being a pointer to the
same data either way, but it's just a good idea to treat it like you
would a 'cpumask_t'. The compat case already did that.
Reported-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/lkml/7d026744-6bd6-6827-0471-b5e8eae0be3f@arm.com/
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f90bd245de ]
fb_set_var would by called when user invokes ioctl with cmd
FBIOPUT_VSCREENINFO. User-provided data would finally reach
tgafb_check_var. In case var->pixclock is assigned to zero,
divide by zero would occur when checking whether reciprocal
of var->pixclock is too high.
Similar crashes have happened in other fbdev drivers. There
is no check and modification on var->pixclock along the call
chain to tgafb_check_var. We believe it could also be triggered
in driver tgafb from user site.
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98e5eb1100 ]
tuning_ctl_set() might have buffer overrun at (X) if it didn't break
from loop by matching (A).
static int tuning_ctl_set(...)
{
for (i = 0; i < TUNING_CTLS_COUNT; i++)
(A) if (nid == ca0132_tuning_ctls[i].nid)
break;
snd_hda_power_up(...);
(X) dspio_set_param(..., ca0132_tuning_ctls[i].mid, ...);
snd_hda_power_down(...); ^
return 1;
}
We will get below error by cppcheck
sound/pci/hda/patch_ca0132.c:4229:2: note: After for loop, i has value 12
for (i = 0; i < TUNING_CTLS_COUNT; i++)
^
sound/pci/hda/patch_ca0132.c:4234:43: note: Array index out of bounds
dspio_set_param(codec, ca0132_tuning_ctls[i].mid, 0x20,
^
This patch cares non match case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sfe9eap7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28e8cabe80 ]
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bc5729227 ]
slot_store() uses kstrtouint() to get a slot number, but stores the
result in an "int" variable (by casting a pointer).
This can result in a negative slot number if the unsigned int value is
very large.
A negative number means that the slot is empty, but setting a negative
slot number this way will not remove the device from the array. I don't
think this is a serious problem, but it could cause confusion and it is
best to fix it.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a075bacde2 ]
The full pagecache drop at the end of FS_IOC_ENABLE_VERITY is causing
performance problems and is hindering adoption of fsverity. It was
intended to solve a race condition where unverified pages might be left
in the pagecache. But actually it doesn't solve it fully.
Since the incomplete solution for this race condition has too much
performance impact for it to be worth it, let's remove it for now.
Fixes: 3fda4c617e ("fs-verity: implement FS_IOC_ENABLE_VERITY ioctl")
Cc: stable@vger.kernel.org
Reviewed-by: Victor Hsieh <victorhsieh@google.com>
Link: https://lore.kernel.org/r/20230314235332.50270-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a02e016a ]
When neither "no_read_workqueue" nor "no_write_workqueue" are enabled,
tasklet_trylock() in crypt_dec_pending() may still return false due to
an uninitialized state, and dm-crypt will unnecessarily do io completion
in io_queue workqueue instead of current context.
Fix this by adding an 'in_tasklet' flag to dm_crypt_io struct and
initialize it to false in crypt_io_init(). Set this flag to true in
kcryptd_queue_crypt() before calling tasklet_schedule(). If set
crypt_dec_pending() will punt io completion to a workqueue.
This also nicely avoids the tasklet_trylock/unlock hack when tasklets
aren't in use.
Fixes: 8e14f61015 ("dm crypt: do not call bio_endio() from the dm-crypt tasklet")
Cc: stable@vger.kernel.org
Reported-by: Hou Tao <houtao1@huawei.com>
Suggested-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1adab2922c ]
If bus type is other than imx50_weim_devtype and have no child devices,
variable 'ret' in function weim_parse_dt() will not be initialized, but
will be used as branch condition and return value. Fix this by
initializing 'ret' with 0.
This was discovered with help of clang-analyzer, but the situation is
quite possible in real life.
Fixes: 52c47b6341 ("bus: imx-weim: improve error handling upon child probe-failure")
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eb39cde1e ]
Nathan reported that when building with GNU as and a version of clang that
defaults to DWARF5, the assembler will complain with:
Error: non-constant .uleb128 is not supported
This is because `-g` defaults to the compiler debug info default. If the
assembler does not support some of the directives used, the above errors
occur. To fix, remove the explicit passing of `-g`.
All the test wants is that stack traces print valid function names, and
debug info is not required for that. (I currently cannot recall why I
added the explicit `-g`.)
Link: https://lkml.kernel.org/r/20230316224705.709984-2-elver@google.com
Fixes: 1fe84fd4a4 ("kcsan: Add test suite")
Signed-off-by: Marco Elver <elver@google.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8a2bb4eb7 ]
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75333d48f9 upstream.
Problem caused by source's vfsmount being unmounted but remains
on the delayed unmount list. This happens when nfs42_ssc_open()
return errors.
Fixed by removing nfsd4_interssc_connect(), leave the vfsmount
for the laundromat to unmount when idle time expires.
We don't need to call nfs_do_sb_deactive when nfs42_ssc_open
return errors since the file was not opened so nfs_server->active
was not incremented. Same as in nfsd4_copy, if we fail to
launch nfsd4_do_async_copy thread then there's no need to
call nfs_do_sb_deactive
Reported-by: Xingyuan Mo <hdthky0@gmail.com>
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Tested-by: Xingyuan Mo <hdthky0@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
