[ Upstream commit e0740fb869 ]
Fix compilation warning on 64bit platforms caused by implicit promotion
of 32bit signed integer to a 64bit unsigned value which happens after
enabling compile-testing of the EMC drivers.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf24b91f4b ]
Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.
Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0171b07373 ]
The microSD card detect pin is physically connected to the MPU pin PI3.
The Device Tree configuration of the card detect pin was wrong—it was
set to pin PB7 instead. If such configuration was used, the kernel would
hang on “Waiting for root device” when booting from a microSD card.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4dd6066bc ]
The 3v3 regulator GPIO is GP6 and not GP7, which is the DDR regulator.
Both regulators are always-on, nevertheless the DT model needs to be
corrected, fix it.
Reported-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f45da704d ]
All Tegra boards which use WM8903 audio codec are specifying a wrong
polarity for the headphones detection GPIO. The kernel driver hardcodes
the polarity to active-low, which is the correct polarity, so we can fix
the device-trees safely.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69db725cdb ]
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7f5ee113 ]
A number of sub-mailbox node names in various OMAP2+ dts files are
currently using underscores. This is not adhering to the node name
convention, fix all of these to use hiphens.
These nodes are already using the prefix mbox, so they will be in
compliance with the sub-mailbox node name convention being added in
the OMAP Mailbox YAML binding as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7d30b8fcd ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2566d5b8c1 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b644c5e01c ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 174a1dcc96 ]
When building with 'make -s', no output to stdout should be printed.
As Arnd Bergmann reported [1], mkimage shows the detailed information
of the generated images.
I think this should be suppressed by the 'cmd' macro instead of by
individual scripts.
Insert 'exec >/dev/null;' in order to redirect stdout to /dev/null for
silent builds.
[Note about this implementation]
'exec >/dev/null;' may look somewhat tricky, but this has a reason.
Appending '>/dev/null' at the end of command line is a common way for
redirection, so I first tried this:
cmd = @set -e; $(echo-cmd) $(cmd_$(1)) >/dev/null
... but it would not work if $(cmd_$(1)) itself contains a redirection.
For example, cmd_wrap in scripts/Makefile.asm-generic redirects the
output from the 'echo' command into the target file.
It would be expanded into:
echo "#include <asm-generic/$*.h>" > $@ >/dev/null
Then, the target file gets empty because the string will go to /dev/null
instead of $@.
Next, I tried this:
cmd = @set -e; $(echo-cmd) { $(cmd_$(1)); } >/dev/null
The form above would be expanded into:
{ echo "#include <asm-generic/$*.h>" > $@; } >/dev/null
This works as expected. However, it would be a syntax error if
$(cmd_$(1)) is empty.
When CONFIG_TRIM_UNUSED_KSYMS is disabled, $(call cmd,gen_ksymdeps) in
scripts/Makefile.build would be expanded into:
set -e; { ; } >/dev/null
..., which causes an syntax error.
I also tried this:
cmd = @set -e; $(echo-cmd) ( $(cmd_$(1)) ) >/dev/null
... but this causes a syntax error for the same reason.
So, finally I adopted:
cmd = @set -e; $(echo-cmd) exec >/dev/null; $(cmd_$(1))
[1]: https://lore.kernel.org/lkml/20210514135752.2910387-1-arnd@kernel.org/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723de6a412 ]
Without SoC specific PHY fixups the network interface on this board will
fail to work. Provide missing DT properties to make it work again.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4beba40119 ]
This adds a mounting matrix to the accelerometer
on the TVK1281618 R3.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917b70281 ]
Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b82f8e2992 ]
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long
dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14cdc1f243 ]
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05cf8fffcd ]
The to_ti_syscon_reset_data macro currently only works if the
parameter passed into it is called 'rcdev'.
Fixes a checkpatch --strict issue:
CHECK: Macro argument reuse 'rcdev' - possible side-effects?
#53: FILE: drivers/reset/reset-ti-syscon.c:53:
+#define to_ti_syscon_reset_data(rcdev) \
+ container_of(rcdev, struct ti_syscon_reset_data, rcdev)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ecfad495 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfbfb86a43 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
