[ Upstream commit 1daea158d0aae0770371f3079305a29fdb66829e ]
As mentioned in the comment, the workaround for
__attribute__((no_stack_protector)) is only necessary on GCC.
Avoid applying the workaround on clang, as clang does not recognize
__attribute__((__optimize__)) and would fail.
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20240807-nolibc-llvm-v2-3-c20f2f5fc7c2@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c01f3815453e2d5f699ccd8c8c1f93a5b8669e59 ]
The current MIDI input flush on HDSP and HDSPM drivers relies on the
hardware reporting the right value. If the hardware doesn't give the
proper value but returns -1, it may be stuck at an infinite loop.
Add a counter and break if the loop is unexpectedly too long.
Link: https://patch.msgid.link/20240808091513.31380-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b986c7430a6bb68d523dac7bfc74cbd5b44ef96 ]
ASIHPI driver stores some values in the static array upon a response
from the driver, and its index depends on the firmware. We shouldn't
trust it blindly.
This patch adds a sanity check of the array index to fit in the array
size.
Link: https://patch.msgid.link/20240808091454.30846-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5760929f6545c651682de3c2c6c6786816b17bb1 ]
A kexec kernel boot failure is sometimes observed on AMD CPUs due to an
unmapped EFI config table array. This can be seen when "nogbpages" is on
the kernel command line, and has been observed as a full BIOS reboot rather
than a successful kexec.
This was also the cause of reported regressions attributed to Commit
7143c5f4cf20 ("x86/mm/ident_map: Use gbpages only where full GB page should
be mapped.") which was subsequently reverted.
To avoid this page fault, explicitly include the EFI config table array in
the kexec identity map.
Further explanation:
The following 2 commits caused the EFI config table array to be
accessed when enabling sev at kernel startup.
commit ec1c66af3a ("x86/compressed/64: Detect/setup SEV/SME features
earlier during boot")
commit c01fce9cef ("x86/compressed: Add SEV-SNP feature
detection/setup")
This is in the code that examines whether SEV should be enabled or not, so
it can even affect systems that are not SEV capable.
This may result in a page fault if the EFI config table array's address is
unmapped. Since the page fault occurs before the new kernel establishes its
own identity map and page fault routines, it is unrecoverable and kexec
fails.
Most often, this problem is not seen because the EFI config table array
gets included in the map by the luck of being placed at a memory address
close enough to other memory areas that *are* included in the map created
by kexec.
Both the "nogbpages" command line option and the "use gpbages only where
full GB page should be mapped" change greatly reduce the chance of being
included in the map by luck, which is why the problem appears.
Signed-off-by: Tao Liu <ltao@redhat.com>
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Pavin Joseph <me@pavinjoseph.com>
Tested-by: Sarah Brofeldt <srhb@dbc.dk>
Tested-by: Eric Hagberg <ehagberg@gmail.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/all/20240717213121.3064030-2-steve.wahl@hpe.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10b554919d4cc8fa8fe2e95b57ad2624728c8e4 ]
A process can disable access to the alternate signal stack by not
enabling the altstack's PKEY in the PKRU register.
Nevertheless, the kernel updates the PKRU temporarily for signal
handling. However, in sigreturn(), restore_sigcontext() will restore the
PKRU to the user-defined PKRU value.
This will cause restore_altstack() to fail with a SIGSEGV as it needs read
access to the altstack which is prohibited by the user-defined PKRU value.
Fix this by restoring altstack before restoring PKRU.
Signed-off-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240802061318.2140081-5-aruna.ramakrishna@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24cf2bc982ffe02aeffb4a3885c71751a2c7023b ]
Assume there's a multithreaded application that runs untrusted user
code. Each thread has its stack/code protected by a non-zero PKEY, and the
PKRU register is set up such that only that particular non-zero PKEY is
enabled. Each thread also sets up an alternate signal stack to handle
signals, which is protected by PKEY zero. The PKEYs man page documents that
the PKRU will be reset to init_pkru when the signal handler is invoked,
which means that PKEY zero access will be enabled. But this reset happens
after the kernel attempts to push fpu state to the alternate stack, which
is not (yet) accessible by the kernel, which leads to a new SIGSEGV being
sent to the application, terminating it.
Enabling both the non-zero PKEY (for the thread) and PKEY zero in
userspace will not work for this use case. It cannot have the alt stack
writeable by all - the rationale here is that the code running in that
thread (using a non-zero PKEY) is untrusted and should not have access
to the alternate signal stack (that uses PKEY zero), to prevent the
return address of a function from being changed. The expectation is that
kernel should be able to set up the alternate signal stack and deliver
the signal to the application even if PKEY zero is explicitly disabled
by the application. The signal handler accessibility should not be
dictated by whatever PKRU value the thread sets up.
The PKRU register is managed by XSAVE, which means the sigframe contents
must match the register contents - which is not the case here. It's
required that the signal frame contains the user-defined PKRU value (so
that it is restored correctly from sigcontext) but the actual register must
be reset to init_pkru so that the alt stack is accessible and the signal
can be delivered to the application. It seems that the proper fix here
would be to remove PKRU from the XSAVE framework and manage it separately,
which is quite complicated. As a workaround, do this:
orig_pkru = rdpkru();
wrpkru(orig_pkru & init_pkru_value);
xsave_to_user_sigframe();
put_user(pkru_sigframe_addr, orig_pkru)
In preparation for writing PKRU to sigframe, pass PKRU as an additional
parameter down the call chain from get_sigframe().
No functional change.
Signed-off-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240802061318.2140081-2-aruna.ramakrishna@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf96ab1a966b87b09fdd9e8cc8357d2d00776a3a ]
Protect against the kcpuid code parsing faulty max subleaf numbers
through a min() expression. Thus, ensuring that max_subleaf will always
be ≤ MAX_SUBLEAF_NUM.
Use "u32" for the subleaf numbers since kcpuid is compiled with -Wextra,
which includes signed/unsigned comparisons warnings.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240718134755.378115-5-darwi@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fbf16992e5aa14acf0441320033a01a32309ded ]
If reading version and variant from registers fails (which is unlikely
but possible, because it is a read over bus), the driver will proceed
and perform device configuration based on uninitialized stack variables.
Handle it a bit better - bail out without doing any init and failing the
update status Soundwire callback.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240710-asoc-wsa88xx-version-v1-2-f1c54966ccde@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d79e13f8e8abb5cd3a2a0f9fc9bc3fc750c5b06f ]
Apply the newly introduced macros for reduce the complex expressions
and cast in the quirk table definitions. It results in a significant
code reduction, too.
There should be no functional changes.
Link: https://patch.msgid.link/20240814134844.2726-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3ad39b791c2ecf718afcaca30e5ceafa939d5c ]
Many entries in the USB-audio quirk tables have relatively complex
expressions. For improving the readability, introduce a few macros.
Those are applied in the following patch.
Link: https://patch.msgid.link/20240814134844.2726-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 830802a0fea8fb39d3dc9fb7d6b5581e1343eb1f ]
Breno observed panics when using failslab under certain conditions during
runtime:
can not alloc irq_pin_list (-1,0,20)
Kernel panic - not syncing: IO-APIC: failed to add irq-pin. Can not proceed
panic+0x4e9/0x590
mp_irqdomain_alloc+0x9ab/0xa80
irq_domain_alloc_irqs_locked+0x25d/0x8d0
__irq_domain_alloc_irqs+0x80/0x110
mp_map_pin_to_irq+0x645/0x890
acpi_register_gsi_ioapic+0xe6/0x150
hpet_open+0x313/0x480
That's a pointless panic which is a leftover of the historic IO/APIC code
which panic'ed during early boot when the interrupt allocation failed.
The only place which might justify panic is the PIT/HPET timer_check() code
which tries to figure out whether the timer interrupt is delivered through
the IO/APIC. But that code does not require to handle interrupt allocation
failures. If the interrupt cannot be allocated then timer delivery fails
and it either panics due to that or falls back to legacy mode.
Cure this by removing the panic wrapper around __add_pin_to_irq_node() and
making mp_irqdomain_alloc() aware of the failure condition and handle it as
any other failure in this function gracefully.
Reported-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Breno Leitao <leitao@debian.org>
Tested-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/all/ZqfJmUF8sXIyuSHN@gmail.com
Link: https://lore.kernel.org/all/20240802155440.275200843@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 901e85677ec0bb9a69fb9eab1feafe0c4eb7d07e ]
For an invalid input value that is out of the given range, currently
USB-audio driver corrects the value silently and accepts without
errors. This is no wrong behavior, per se, but the recent kselftest
rather wants to have an error in such a case, hence a different
behavior is expected now.
This patch adds a sanity check at each control put for the standard
mixer types and returns an error if an invalid value is given.
Note that this covers only the standard mixer types. The mixer quirks
that have own control callbacks would need different coverage.
Link: https://patch.msgid.link/20240806124651.28203-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 498365e52bebcbc36a93279fe7e9d6aec8479cee ]
Replace one-element array with a flexible-array member in
`struct host_cmd_ds_802_11_scan_ext`.
With this, fix the following warning:
elo 16 17:51:58 surfacebook kernel: ------------[ cut here ]------------
elo 16 17:51:58 surfacebook kernel: memcpy: detected field-spanning write (size 243) of single field "ext_scan->tlv_buffer" at drivers/net/wireless/marvell/mwifiex/scan.c:2239 (size 1)
elo 16 17:51:58 surfacebook kernel: WARNING: CPU: 0 PID: 498 at drivers/net/wireless/marvell/mwifiex/scan.c:2239 mwifiex_cmd_802_11_scan_ext+0x83/0x90 [mwifiex]
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Closes: https://lore.kernel.org/linux-hardening/ZsZNgfnEwOcPdCly@black.fi.intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/ZsZa5xRcsLq9D+RX@elsanto
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2423cc20087ae9a7b7af575aa62304ef67cad7b6 ]
This patch moves the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_changelink in front of the evaluation of data[IFLA_CAN_BITTIMING].
This avoids a call to do_set_data_bittiming providing a stale
can_priv::ctrlmode with a CAN_CTRLMODE_FD flag not matching the
requested state when switching between a CAN Classic and CAN-FD bitrate.
In the same manner the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_validate is also moved in front of the evaluation of
data[IFLA_CAN_BITTIMING].
This is a preparation for patches where the nominal and data bittiming
may have interdependencies on the driver side depending on the
CAN_CTRLMODE_FD flag state.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://patch.msgid.link/20240808164224.213522-1-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e9629d0ae977d6f6916d7e519724804e95f0b07 ]
Use perf_allow_kernel() for 'pa_enable' (physical addresses),
'pct_enable' (physical timestamps) and context IDs. This means that
perf_event_paranoid is now taken into account and LSM hooks can be used,
which is more consistent with other perf_event_open calls. For example
PERF_SAMPLE_PHYS_ADDR uses perf_allow_kernel() rather than just
perfmon_capable().
This also indirectly fixes the following error message which is
misleading because perf_event_paranoid is not taken into account by
perfmon_capable():
$ perf record -e arm_spe/pa_enable/
Error:
Access to performance monitoring and observability operations is
limited. Consider adjusting /proc/sys/kernel/perf_event_paranoid
setting ...
Suggested-by: Al Grant <al.grant@arm.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240827145113.1224604-1-james.clark@linaro.org
Link: https://lore.kernel.org/all/20240807120039.GD37996@noisy.programming.kicks-ass.net/
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9e5df4a257afc3a471a82961ace9a22b88295a ]
We found that one close-wait socket was reset by the other side
due to a new connection reusing the same port which is beyond our
expectation, so we have to investigate the underlying reason.
The following experiment is conducted in the test environment. We
limit the port range from 40000 to 40010 and delay the time to close()
after receiving a fin from the active close side, which can help us
easily reproduce like what happened in production.
Here are three connections captured by tcpdump:
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965525191
127.0.0.1.9999 > 127.0.0.1.40002: Flags [S.], seq 2769915070
127.0.0.1.40002 > 127.0.0.1.9999: Flags [.], ack 1
127.0.0.1.40002 > 127.0.0.1.9999: Flags [F.], seq 1, ack 1
// a few seconds later, within 60 seconds
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965590730
127.0.0.1.9999 > 127.0.0.1.40002: Flags [.], ack 2
127.0.0.1.40002 > 127.0.0.1.9999: Flags [R], seq 2965525193
// later, very quickly
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965590730
127.0.0.1.9999 > 127.0.0.1.40002: Flags [S.], seq 3120990805
127.0.0.1.40002 > 127.0.0.1.9999: Flags [.], ack 1
As we can see, the first flow is reset because:
1) client starts a new connection, I mean, the second one
2) client tries to find a suitable port which is a timewait socket
(its state is timewait, substate is fin_wait2)
3) client occupies that timewait port to send a SYN
4) server finds a corresponding close-wait socket in ehash table,
then replies with a challenge ack
5) client sends an RST to terminate this old close-wait socket.
I don't think the port selection algo can choose a FIN_WAIT2 socket
when we turn on tcp_tw_reuse because on the server side there
remain unread data. In some cases, if one side haven't call close() yet,
we should not consider it as expendable and treat it at will.
Even though, sometimes, the server isn't able to call close() as soon
as possible like what we expect, it can not be terminated easily,
especially due to a second unrelated connection happening.
After this patch, we can see the expected failure if we start a
connection when all the ports are occupied in fin_wait2 state:
"Ncat: Cannot assign requested address."
Reported-by: Jade Dong <jadedong@tencent.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240823001152.31004-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae5a0456e0b4cfd7e61619e55251ffdf1bc7adfb ]
Modify netpoll_setup() and __netpoll_setup() to ensure that the netpoll
structure (np) is left in a clean state if setup fails for any reason.
This prevents carrying over misconfigured fields in case of partial
setup success.
Key changes:
- np->dev is now set only after successful setup, ensuring it's always
NULL if netpoll is not configured or if netpoll_setup() fails.
- np->local_ip is zeroed if netpoll setup doesn't complete successfully.
- Added DEBUG_NET_WARN_ON_ONCE() checks to catch unexpected states.
- Reordered some operations in __netpoll_setup() for better logical flow.
These changes improve the reliability of netpoll configuration, since it
assures that the structure is fully initialized or totally unset.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240822111051.179850-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c44d31cb34ce4eb8311a2e73634d57702948230 ]
Algorithm registration is usually carried out during module init,
where as little work as possible should be carried out. The SIMD
code violated this rule by allocating a tfm, this then triggers a
full test of the algorithm which may dead-lock in certain cases.
SIMD is only allocating the tfm to get at the alg object, which is
in fact already available as it is what we are registering. Use
that directly and remove the crypto_alloc_tfm call.
Also remove some obsolete and unused SIMD API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5874e0c9f25661c2faefe4809907166defae3d7f ]
W=1 builds with GCC 14.2.0 warn that:
.../aq_ethtool.c:278:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 6 [-Wformat-truncation=]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~
.../aq_ethtool.c:278:56: note: directive argument in the range [-2147483641, 254]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~
.../aq_ethtool.c:278:33: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tc is always in the range 0 - cfg->tcs. And as cfg->tcs is a u8,
the range is 0 - 255. Further, on inspecting the code, it seems
that cfg->tcs will never be more than AQ_CFG_TCS_MAX (8), so
the range is actually 0 - 8.
So, it seems that the condition that GCC flags will not occur.
But, nonetheless, it would be nice if it didn't emit the warning.
It seems that this can be achieved by changing the format specifier
from %d to %u, in which case I believe GCC recognises an upper bound
on the range of tc of 0 - 255. After some experimentation I think
this is due to the combination of the use of %u and the type of
cfg->tcs (u8).
Empirically, updating the type of the tc variable to unsigned int
has the same effect.
As both of these changes seem to make sense in relation to what the code
is actually doing - iterating over unsigned values - do both.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821-atlantic-str-v1-1-fa2cfe38ca00@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fed54758cd248cd311a2b5c1e180abef1866237 ]
The NETLINK_FIB_LOOKUP netlink family can be used to perform a FIB
lookup according to user provided parameters and communicate the result
back to user space.
However, unlike other users of the FIB lookup API, the upper DSCP bits
and the ECN bits of the DS field are not masked, which can result in the
wrong result being returned.
Solve this by masking the upper DSCP bits and the ECN bits using
IPTOS_RT_MASK.
The structure that communicates the request and the response is not
exported to user space, so it is unlikely that this netlink family is
actually in use [1].
[1] https://lore.kernel.org/netdev/ZpqpB8vJU%2FQ6LSqa@debian/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45742881f9eee2a4daeb6008e648a460dd3742cd ]
Coverity reported that u8 rx_mask << 24 will become signed 32 bits, which
casting to unsigned 64 bits will do sign extension. For example,
putting 0x80000000 (signed 32 bits) to a u64 variable will become
0xFFFFFFFF_80000000.
The real case we meet is:
rx_mask[0...3] = ff ff 00 00
ra_mask = 0xffffffff_ff0ff000
After this fix:
rx_mask[0...3] = ff ff 00 00
ra_mask = 0x00000000_ff0ff000
Fortunately driver does bitwise-AND with incorrect ra_mask and supported
rates (1ss and 2ss rate only) afterward, so the final rate mask of
original code is still correct.
Addresses-Coverity-ID: 1504762 ("Unintended sign extension")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240809072012.84152-5-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3af3d3c5b26c33a7950e34e137584f6056c4319 ]
dev->ip_ptr could be NULL if we set an invalid MTU.
Even then, if we issue ioctl(SIOCSIFADDR) for a new IPv4 address,
devinet_ioctl() allocates struct in_ifaddr and fails later in
inet_set_ifa() because in_dev is NULL.
Let's move the check earlier.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20240809235406.50187-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffff7ee843c351ce71d6e0d52f0f20bea35e18c9 ]
This corrects an out-by-one error in the maximum length of the package
version string. The size argument of snprintf includes space for the
trailing '\0' byte, so there is no need to allow extra space for it by
reducing the value of the size argument by 1.
Found by inspection.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20240813-bnxt-str-v2-1-872050a157e7@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91d516d4de48532d967a77967834e00c8c53dfe6 ]
Increase size of queue_name buffer from 30 to 31 to accommodate
the largest string written to it. This avoids truncation in
the possibly unlikely case where the string is name is the
maximum size.
Flagged by gcc-14:
.../mvpp2_main.c: In function 'mvpp2_probe':
.../mvpp2_main.c:7636:32: warning: 'snprintf' output may be truncated before the last format character [-Wformat-truncation=]
7636 | "stats-wq-%s%s", netdev_name(priv->port_list[0]->dev),
| ^
.../mvpp2_main.c:7635:9: note: 'snprintf' output between 10 and 31 bytes into a destination of size 30
7635 | snprintf(priv->queue_name, sizeof(priv->queue_name),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
7636 | "stats-wq-%s%s", netdev_name(priv->port_list[0]->dev),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
7637 | priv->port_count > 1 ? "+" : "");
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Introduced by commit 118d6298f6 ("net: mvpp2: add ethtool GOP statistics").
I am not flagging this as a bug as I am not aware that it is one.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Wojtas <marcin.s.wojtas@gmail.com>
Link: https://patch.msgid.link/20240806-mvpp2-namelen-v1-1-6dc773653f2f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6555a2a9212be6983d2319d65276484f7c5f431a ]
Smatch reports that copying media_name and if_name to name_parts may
overwrite the destination.
.../bearer.c:166 bearer_name_validate() error: strcpy() 'media_name' too large for 'name_parts->media_name' (32 vs 16)
.../bearer.c:167 bearer_name_validate() error: strcpy() 'if_name' too large for 'name_parts->if_name' (1010102 vs 16)
This does seem to be the case so guard against this possibility by using
strscpy() and failing if truncation occurs.
Introduced by commit b97bf3fd8f ("[TIPC] Initial merge")
Compile tested only.
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240801-tipic-overrun-v2-1-c5b869d1f074@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc171114926ec390ab90f46534545420ec03e458 ]
It is not particularly useful to release locks (the EC mutex and the
ACPI global lock, if present) and re-acquire them immediately thereafter
during EC address space accesses in acpi_ec_space_handler().
First, releasing them for a while before grabbing them again does not
really help anyone because there may not be enough time for another
thread to acquire them.
Second, if another thread successfully acquires them and carries out
a new EC write or read in the middle if an operation region access in
progress, it may confuse the EC firmware, especially after the burst
mode has been enabled.
Finally, manipulating the locks after writing or reading every single
byte of data is overhead that it is better to avoid.
Accordingly, modify the code to carry out EC address space accesses
entirely without releasing the locks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/12473338.O9o76ZdvQC@rjwysocki.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69f253e46af98af17e3efa3e5dfa72fcb7d1983d ]
Currently, the ath11k_soc_dp_stats::hal_reo_error array is defined with a
maximum size of DP_REO_DST_RING_MAX. However, the ath11k_dp_process_rx()
function access ath11k_soc_dp_stats::hal_reo_error using the REO
destination SRNG ring ID, which is incorrect. SRNG ring ID differ from
normal ring ID, and this usage leads to out-of-bounds array access. To fix
this issue, modify ath11k_dp_process_rx() to use the normal ring ID
directly instead of the SRNG ring ID to avoid out-of-bounds array access.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240704070811.4186543-3-quic_periyasa@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e106b7ad13c1d246adaa57df73edb8f8b8acb240 ]
Currently, the ath12k_soc_dp_stats::hal_reo_error array is defined with a
maximum size of DP_REO_DST_RING_MAX. However, the ath12k_dp_rx_process()
function access ath12k_soc_dp_stats::hal_reo_error using the REO
destination SRNG ring ID, which is incorrect. SRNG ring ID differ from
normal ring ID, and this usage leads to out-of-bounds array access. To
fix this issue, modify ath12k_dp_rx_process() to use the normal ring ID
directly instead of the SRNG ring ID to avoid out-of-bounds array access.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240704070811.4186543-2-quic_periyasa@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bce8005ec0dcb23a58300e8522fe4a31da606fa ]
Recently running UBSAN caught few out of bound shifts in the
ioc_forgive_debts() function:
UBSAN: shift-out-of-bounds in block/blk-iocost.c:2142:38
shift exponent 80 is too large for 64-bit type 'u64' (aka 'unsigned long
long')
...
UBSAN: shift-out-of-bounds in block/blk-iocost.c:2144:30
shift exponent 80 is too large for 64-bit type 'u64' (aka 'unsigned long
long')
...
Call Trace:
<IRQ>
dump_stack_lvl+0xca/0x130
__ubsan_handle_shift_out_of_bounds+0x22c/0x280
? __lock_acquire+0x6441/0x7c10
ioc_timer_fn+0x6cec/0x7750
? blk_iocost_init+0x720/0x720
? call_timer_fn+0x5d/0x470
call_timer_fn+0xfa/0x470
? blk_iocost_init+0x720/0x720
__run_timer_base+0x519/0x700
...
Actual impact of this issue was not identified but I propose to fix the
undefined behaviour.
The proposed fix to prevent those out of bound shifts consist of
precalculating exponent before using it the shift operations by taking
min value from the actual exponent and maximum possible number of bits.
Reported-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Konstantin Ovsepian <ovs@ovs.to>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240822154137.2627818-1-ovs@ovs.to
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaf21ac93909e08a12931173336bdb52ac8499f1 ]
Some Asus AMD systems are reported to not be able to change EPP values
because the BIOS doesn't advertise support for the CPPC MSR and the PCC
region is not configured.
However the ACPI 6.2 specification allows CPC registers to be declared
in FFH:
```
Starting with ACPI Specification 6.2, all _CPC registers can be in
PCC, System Memory, System IO, or Functional Fixed Hardware address
spaces. OSPM support for this more flexible register space scheme
is indicated by the “Flexible Address Space for CPPC Registers” _OSC
bit.
```
If this _OSC has been set allow using FFH to configure EPP.
Reported-by: al0uette@outlook.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218686
Suggested-by: al0uette@outlook.com
Tested-by: vderp@icloud.com
Tested-by: al0uette@outlook.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20240910031524.106387-1-superm1@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb7b0f12e13ba99e64e3a690c2166895ed63b437 ]
The Panasonic Toughbook CF-18 advertises both native and vendor backlight
control interfaces. But only the vendor one actually works.
acpi_video_get_backlight_type() will pick the non working native backlight
by default, add a quirk to select the working vendor backlight instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240907124419.21195-1-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a0570948c5def5c59e588dc0e009ed850a1f5a1 ]
For tracking multiple devices concurrently with a condition.
The patch enables the HCI_QUIRK_USE_MSFT_EXT_ADDRESS_FILTER quirk
on RTL8852B controller.
The quirk setting is based on commit 9e14606d8f ("Bluetooth: msft:
Extended monitor tracking by address filter")
With this setting, when a pattern monitor detects a device, this
feature issues an address monitor for tracking that device. Let the
original pattern monitor keep monitor new devices.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6ad4d9e1690c7faa3a53f762c877e477093657 ]
Occasionally when the system goes into pm_suspend, the suspend might fail
due to a PHY access error on the network adapter. Previously, this would
have caused the whole system to fail to go to a low power state.
An example of this was reported in the following Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=205015
[ 1663.694828] e1000e 0000:00:19.0 eth0: Failed to disable ULP
[ 1664.731040] asix 2-3:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 1665.093513] e1000e 0000:00:19.0 eth0: Hardware Error
[ 1665.596760] e1000e 0000:00:19.0: pci_pm_resume+0x0/0x80 returned 0 after 2975399 usecs
and then the system never recovers from it, and all the following suspend failed due to this
[22909.393854] PM: pci_pm_suspend(): e1000e_pm_suspend+0x0/0x760 [e1000e] returns -2
[22909.393858] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -2
[22909.393861] PM: Device 0000:00:1f.6 failed to suspend async: error -2
This can be avoided by changing the return values of __e1000_shutdown and
e1000e_pm_suspend functions so that they always return 0 (success). This
is consistent with what other drivers do.
If the e1000e driver encounters a hardware error during suspend, potential
side effects include slightly higher power draw or non-working wake on
LAN. This is preferred to a system-level suspend failure, and a warning
message is written to the system log, so that the user can be aware that
the LAN controller experienced a problem during suspend.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205015
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6169a8ffee8a012badd8c703716e761ce851b15 ]
ACPICA commit 1280045754264841b119a5ede96cd005bc09b5a7
If acpi_ps_get_next_field() fails, the previously created field list
needs to be properly disposed before returning the status code.
Link: https://github.com/acpica/acpica/commit/12800457
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
[ rjw: Rename local variable to avoid compiler confusion ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
