commit 5719df243e upstream.
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af3260528 ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22
To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().
Fixes: 2743e7f90d ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fdf5c6e6 upstream.
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bf2761c83 upstream.
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b7f56fbc7 upstream.
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f62f3c2064 upstream.
The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.
Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].
Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.
Fixes: 8e591cb720 ("KVM: PPC: Book3S: Add infrastructure to implement kernel-side RTAS calls")
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72f68bf5c7 upstream.
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2b951915 upstream.
SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:
In snd_sb_csp_stop():
spin_lock_irqsave(&p->chip->mixer_lock, flags);
spin_lock(&p->chip->reg_lock);
In snd_sb_csp_load():
spin_lock_irqsave(&p->chip->reg_lock, flags);
spin_lock(&p->chip->mixer_lock);
Also the similar pattern is seen in snd_sb_csp_start().
Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.
This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7b0fcdaf-cd4f-4728-2eae-48c151a92e10@gmail.com
Link: https://lore.kernel.org/r/20210716132723.13216-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 68046cc531 which is
commit ed914d48b6 upstream.
Commit b2b29d6d01 (mm: account PMD tables like PTE tables) is
introduced between v5.9 and v5.10, so this fix (commit 002d8b395f)
should NOT apply to any pre-5.10 branch.
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d85a6f44b ]
The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58acd10092 ]
syzbot reported a call trace:
BUG: KASAN: use-after-free in sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
Call Trace:
sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
sctp_set_owner_w net/sctp/socket.c:131 [inline]
sctp_sendmsg_to_asoc+0x152e/0x2180 net/sctp/socket.c:1865
sctp_sendmsg+0x103b/0x1d30 net/sctp/socket.c:2027
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:821
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:723
This is an use-after-free issue caused by not updating asoc->shkey after
it was replaced in the key list asoc->endpoint_shared_keys, and the old
key was freed.
This patch is to fix by also updating active_key for asoc when old key is
being replaced with a new one. Note that this issue doesn't exist in
sctp_auth_del_key_id(), as it's not allowed to delete the active_key
from the asoc.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: syzbot+b774577370208727d12b@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3a1a937f7 ]
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 727d6a8b7e ]
Currently tcf_skbmod_act() assumes that packets use Ethernet as their L2
protocol, which is not always the case. As an example, for CAN devices:
$ ip link add dev vcan0 type vcan
$ ip link set up vcan0
$ tc qdisc add dev vcan0 root handle 1: htb
$ tc filter add dev vcan0 parent 1: protocol ip prio 10 \
matchall action skbmod swap mac
Doing the above silently corrupts all the packets. Do not perform skbmod
actions for non-Ethernet packets.
Fixes: 86da71b573 ("net_sched: Introduce skbmod action")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f20c8adb1 ]
tfo_active_disable_stamp is read and written locklessly.
We need to annotate these accesses appropriately.
Then, we need to perform the atomic_inc(tfo_active_disable_times)
after the timestamp has been updated, and thus add barriers
to make sure tcp_fastopen_active_should_disable() wont read
a stale timestamp.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56912da7a6 ]
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e746f3451e ]
A ISCSI_IFACE_PARAM can have the same value as a ISCSI_NET_PARAM so when
iscsi_iface_attr_is_visible tries to figure out the type by just checking
the value, we can collide and return the wrong type. When we call into the
driver we might not match and return that we don't want attr visible in
sysfs. The patch fixes this by setting the type when we figure out what the
param is.
Link: https://lore.kernel.org/r/20210701002559.89533-1-michael.christie@oracle.com
Fixes: 3e0f65b34c ("[SCSI] iscsi_transport: Additional parameters for network settings")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517a16b1a8 ]
Commit 63346650c1 ("netrom: switch to sock timer API") switched to use
sock timer API. It replaces mod_timer() by sk_reset_timer(), and
del_timer() by sk_stop_timer().
Function sk_reset_timer() will increase the refcount of sock if it is
called on an inactive timer, hence, in case the timer expires, we need to
decrease the refcount ourselves in the handler, otherwise, the sock
refcount will be unbalanced and the sock will never be freed.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+10f1194569953b72f1ae@syzkaller.appspotmail.com
Fixes: 63346650c1 ("netrom: switch to sock timer API")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f119ba1d5 ]
The release_sock() is blocking function, it would change the state
after sleeping. use wait_woken() instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991e634360 ]
When nr_segs equal to zero in iovec_from_user, the object
msg->msg_iter.iov is uninit stack memory in caif_seqpkt_sendmsg
which is defined in ___sys_sendmsg. So we cann't just judge
msg->msg_iter.iov->base directlly. We can use nr_segs to judge
msg in caif_seqpkt_sendmsg whether has data buffers.
=====================================================
BUG: KMSAN: uninit-value in caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
____sys_sendmsg+0x12b6/0x1350 net/socket.c:2343
___sys_sendmsg net/socket.c:2397 [inline]
__sys_sendmmsg+0x808/0xc90 net/socket.c:2480
__compat_sys_sendmmsg net/compat.c:656 [inline]
Reported-by: syzbot+09a5d591c1f98cf5efcb@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=1ace85e8fc9b0d5a45c08c2656c3e91762daa9b8
Fixes: bece7b2398 ("caif: Rewritten socket implementation")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9109165625 ]
Currently array jit->seen_reg[r1] is being accessed before the range
checking of index r1. The range changing on r1 should be performed
first since it will avoid any potential out-of-range accesses on the
array seen_reg[] and also it is more optimal to perform checks on r1
before fetching data from the array. Fix this by swapping the order
of the checks before the array access.
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/bpf/20210715125712.24690-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7efc2ce3d ]
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 251ef6f71b ]
nvme_dev_remove_admin could free dev->admin_q and the admin_tagset
while they are being accessed by nvme_dev_disable(), which can be called
by nvme_reset_work via nvme_remove_dead_ctrl.
Commit cb4bfda62a ("nvme-pci: fix hot removal during error handling")
intended to avoid requests being stuck on a removed controller by killing
the admin queue. But the later fix c8e9e9b764 ("nvme-pci: unquiesce
admin queue on shutdown"), together with nvme_dev_disable(dev, true)
right before nvme_dev_remove_admin() could help dispatch requests and
fail them early, so we don't need nvme_dev_remove_admin() any more.
Fixes: cb4bfda62a ("nvme-pci: fix hot removal during error handling")
Signed-off-by: Casey Chen <cachen@purestorage.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd27f05ae ]
The goal of commit df789fe752 ("ipv6: Provide ipv6 version of
"disable_policy" sysctl") was to have the disable_policy from ipv4
available on ipv6.
However, it's not exactly the same mechanism. On IPv4, all packets coming
from an interface, which has disable_policy set, bypass the policy check.
For ipv6, this is done only for local packets, ie for packets destinated to
an address configured on the incoming interface.
Let's align ipv6 with ipv4 so that the 'disable_policy' sysctl has the same
effect for both protocols.
My first approach was to create a new kind of route cache entries, to be
able to set DST_NOPOLICY without modifying routes. This would have added a
lot of code. Because the local delivery path is already handled, I choose
to focus on the forwarding path to minimize code churn.
Fixes: df789fe752 ("ipv6: Provide ipv6 version of "disable_policy" sysctl")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af30cbd2f4 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85e14d68f ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 19ae1b3fb9 ("fm10k: Add support for PCI power management and error handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fea03b1ceb ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72 ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2aefcd5e ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 6fabd715e6 ("ixgbe: Implement PCIe AER support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b292608db ]
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9992a078b1 upstream.
Commit 28e104d002 ("net: ip_tunnel: fix mtu calculation") removed
dev->hard_header_len subtraction when calculate MTU for tunnel devices
as there is an overhead for device that has header_ops.
But there are ETHER tunnel devices, like gre_tap or erspan, which don't
have header_ops but set dev->hard_header_len during setup. This makes
pkts greater than (MTU - ETH_HLEN) could not be xmited. Fix it by
subtracting the ETHER tunnel devices' dev->hard_header_len for MTU
calculation.
Fixes: 28e104d002 ("net: ip_tunnel: fix mtu calculation")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
