[ Upstream commit fd86dd2a5d ]
According to bindings, the compatible must include microchip,mpfs. This
fixes dtbs_check warning:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: /: compatible: ['microchip,mpfs-icicle-kit'] is too short
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6663b138de ]
Inconsistent node block will cause a file fail to open or read,
which could make the user process crashes or stucks. Let's mark
SBI_NEED_FSCK flag to trigger a fix at next fsck time. After
unlinking the corrupted file, the user process could regenerate
a new one and work correctly.
Signed-off-by: Weichao Guo <guoweichao@oppo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5c0042200 ]
As Yi Zhuang reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=214299
There is potential deadlock during quota data flush as below:
Thread A: Thread B:
f2fs_dquot_acquire
down_read(&sbi->quota_sem)
f2fs_write_checkpoint
block_operations
f2fs_look_all
down_write(&sbi->cp_rwsem)
f2fs_quota_write
f2fs_write_begin
__do_map_lock
f2fs_lock_op
down_read(&sbi->cp_rwsem)
__need_flush_qutoa
down_write(&sbi->quota_sem)
This patch changes block_operations() to use trylock, if it fails,
it means there is potential quota data updater, in this condition,
let's flush quota data first and then trylock again to check dirty
status of quota data.
The side effect is: in heavy race condition (e.g. multi quota data
upaters vs quota data flusher), it may decrease the probability of
synchronizing quota data successfully in checkpoint() due to limited
retry time of quota flush.
Reported-by: Yi Zhuang <zhuangyi1@huawei.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86dc40c7ea ]
When supporting only the .map and .unmap callbacks of iommu_ops,
the IOMMU driver can make assumptions about the size and alignment
used for mappings based on the driver provided pgsize_bitmap. VT-d
previously used essentially PAGE_MASK for this bitmap as any power
of two mapping was acceptably filled by native page sizes.
However, with the .map_pages and .unmap_pages interface we're now
getting page-size and count arguments. If we simply combine these
as (page-size * count) and make use of the previous map/unmap
functions internally, any size and alignment assumptions are very
different.
As an example, a given vfio device assignment VM will often create
a 4MB mapping at IOVA pfn [0x3fe00 - 0x401ff]. On a system that
does not support IOMMU super pages, the unmap_pages interface will
ask to unmap 1024 4KB pages at the base IOVA. dma_pte_clear_level()
will recurse down to level 2 of the page table where the first half
of the pfn range exactly matches the entire pte level. We clear the
pte, increment the pfn by the level size, but (oops) the next pte is
on a new page, so we exit the loop an pop back up a level. When we
then update the pfn based on that higher level, we seem to assume
that the previous pfn value was at the start of the level. In this
case the level size is 256K pfns, which we add to the base pfn and
get a results of 0x7fe00, which is clearly greater than 0x401ff,
so we're done. Meanwhile we never cleared the ptes for the remainder
of the range. When the VM remaps this range, we're overwriting valid
ptes and the VT-d driver complains loudly, as reported by the user
report linked below.
The fix for this seems relatively simple, if each iteration of the
loop in dma_pte_clear_level() is assumed to clear to the end of the
level pte page, then our next pfn should be calculated from level_pfn
rather than our working pfn.
Fixes: 3f34f12597 ("iommu/vt-d: Implement map/unmap_pages() iommu_ops callback")
Reported-by: Ajay Garg <ajaygargnsit@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Link: https://lore.kernel.org/all/20211002124012.18186-1-ajaygargnsit@gmail.com/
Link: https://lore.kernel.org/r/163659074748.1617923.12716161410774184024.stgit@omen
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211126135556.397932-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce1ca0525 ]
To hot unplug a CPU, the idle task on that CPU calls a few layers of C
code before finally leaving the kernel. When KASAN is in use, poisoned
shadow is left around for each of the active stack frames, and when
shadow call stacks are in use. When shadow call stacks (SCS) are in use
the task's saved SCS SP is left pointing at an arbitrary point within
the task's shadow call stack.
When a CPU is offlined than onlined back into the kernel, this stale
state can adversely affect execution. Stale KASAN shadow can alias new
stackframes and result in bogus KASAN warnings. A stale SCS SP is
effectively a memory leak, and prevents a portion of the shadow call
stack being used. Across a number of hotplug cycles the idle task's
entire shadow call stack can become unusable.
We previously fixed the KASAN issue in commit:
e1b77c9298 ("sched/kasan: remove stale KASAN poison after hotplug")
... by removing any stale KASAN stack poison immediately prior to
onlining a CPU.
Subsequently in commit:
f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
... the refactoring left the KASAN and SCS cleanup in one-time idle
thread initialization code rather than something invoked prior to each
CPU being onlined, breaking both as above.
We fixed SCS (but not KASAN) in commit:
63acd42c0d ("sched/scs: Reset the shadow stack when idle_task_exit")
... but as this runs in the context of the idle task being offlined it's
potentially fragile.
To fix these consistently and more robustly, reset the SCS SP and KASAN
shadow of a CPU's idle task immediately before we online that CPU in
bringup_cpu(). This ensures the idle task always has a consistent state
when it is running, and removes the need to so so when exiting an idle
task.
Whenever any thread is created, dup_task_struct() will give the task a
stack which is free of KASAN shadow, and initialize the task's SCS SP,
so there's no need to specially initialize either for idle thread within
init_idle(), as this was only necessary to handle hotplug cycles.
I've tested this on arm64 with:
* gcc 11.1.0, defconfig +KASAN_INLINE, KASAN_STACK
* clang 12.0.0, defconfig +KASAN_INLINE, KASAN_STACK, SHADOW_CALL_STACK
... offlining and onlining CPUS with:
| while true; do
| for C in /sys/devices/system/cpu/cpu*/online; do
| echo 0 > $C;
| echo 1 > $C;
| done
| done
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Qian Cai <quic_qiancai@quicinc.com>
Link: https://lore.kernel.org/lkml/20211115113310.35693-1-mark.rutland@arm.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73743c3b09 ]
syzbot reported that the warning in perf_sigtrap() fires, saying that
the event's task does not match current:
| WARNING: CPU: 0 PID: 9090 at kernel/events/core.c:6446 perf_pending_event+0x40d/0x4b0 kernel/events/core.c:6513
| Modules linked in:
| CPU: 0 PID: 9090 Comm: syz-executor.1 Not tainted 5.15.0-syzkaller #0
| Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
| RIP: 0010:perf_sigtrap kernel/events/core.c:6446 [inline]
| RIP: 0010:perf_pending_event_disable kernel/events/core.c:6470 [inline]
| RIP: 0010:perf_pending_event+0x40d/0x4b0 kernel/events/core.c:6513
| ...
| Call Trace:
| <IRQ>
| irq_work_single+0x106/0x220 kernel/irq_work.c:211
| irq_work_run_list+0x6a/0x90 kernel/irq_work.c:242
| irq_work_run+0x4f/0xd0 kernel/irq_work.c:251
| __sysvec_irq_work+0x95/0x3d0 arch/x86/kernel/irq_work.c:22
| sysvec_irq_work+0x8e/0xc0 arch/x86/kernel/irq_work.c:17
| </IRQ>
| <TASK>
| asm_sysvec_irq_work+0x12/0x20 arch/x86/include/asm/idtentry.h:664
| RIP: 0010:__raw_spin_unlock_irqrestore include/linux/spinlock_api_smp.h:152 [inline]
| RIP: 0010:_raw_spin_unlock_irqrestore+0x38/0x70 kernel/locking/spinlock.c:194
| ...
| coredump_task_exit kernel/exit.c:371 [inline]
| do_exit+0x1865/0x25c0 kernel/exit.c:771
| do_group_exit+0xe7/0x290 kernel/exit.c:929
| get_signal+0x3b0/0x1ce0 kernel/signal.c:2820
| arch_do_signal_or_restart+0x2a9/0x1c40 arch/x86/kernel/signal.c:868
| handle_signal_work kernel/entry/common.c:148 [inline]
| exit_to_user_mode_loop kernel/entry/common.c:172 [inline]
| exit_to_user_mode_prepare+0x17d/0x290 kernel/entry/common.c:207
| __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
| syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300
| do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
| entry_SYSCALL_64_after_hwframe+0x44/0xae
On x86 this shouldn't happen, which has arch_irq_work_raise().
The test program sets up a perf event with sigtrap set to fire on the
'sched_wakeup' tracepoint, which fired in ttwu_do_wakeup().
This happened because the 'sched_wakeup' tracepoint also takes a task
argument passed on to perf_tp_event(), which is used to deliver the
event to that other task.
Since we cannot deliver synchronous signals to other tasks, skip an event if
perf_tp_event() is targeted at another task and perf_event_attr::sigtrap is
set, which will avoid ever entering perf_sigtrap() for such events.
Fixes: 97ba62b278 ("perf: Add support for SIGTRAP on perf events")
Reported-by: syzbot+663359e32ce6f1a305ad@syzkaller.appspotmail.com
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YYpoCOBmC/kJWfmI@elver.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d257cc8cb8 ]
There are some inconsistency in the way that the handoff bit is being
handled in readers and writers that lead to a race condition.
Firstly, when a queue head writer set the handoff bit, it will clear
it when the writer is being killed or interrupted on its way out
without acquiring the lock. That is not the case for a queue head
reader. The handoff bit will simply be inherited by the next waiter.
Secondly, in the out_nolock path of rwsem_down_read_slowpath(), both
the waiter and handoff bits are cleared if the wait queue becomes
empty. For rwsem_down_write_slowpath(), however, the handoff bit is
not checked and cleared if the wait queue is empty. This can
potentially make the handoff bit set with empty wait queue.
Worse, the situation in rwsem_down_write_slowpath() relies on wstate,
a variable set outside of the critical section containing the ->count
manipulation, this leads to race condition where RWSEM_FLAG_HANDOFF
can be double subtracted, corrupting ->count.
To make the handoff bit handling more consistent and robust, extract
out handoff bit clearing code into the new rwsem_del_waiter() helper
function. Also, completely eradicate wstate; always evaluate
everything inside the same critical section.
The common function will only use atomic_long_andnot() to clear bits
when the wait queue is empty to avoid possible race condition. If the
first waiter with handoff bit set is killed or interrupted to exit the
slowpath without acquiring the lock, the next waiter will inherit the
handoff bit.
While at it, simplify the trylock for loop in
rwsem_down_write_slowpath() to make it easier to read.
Fixes: 4f23dbc1e6 ("locking/rwsem: Implement lock handoff to prevent lock starvation")
Reported-by: Zhenhua Ma <mazhenhua@xiaomi.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211116012912.723980-1-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c49a35eedf ]
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82229c4dbb ]
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d2ad993aa ]
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01d9cc2dea ]
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0276af2176 ]
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes: f3ccfda193 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b270bfe697 ]
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207 ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3911f73f5 ]
We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.
Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).
Use a callback building method similar to what we do for struct proto.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Fixes: d4ffb02dee ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e062fe99cc ]
recvmsg() will put peek()ed and partially read records onto the rx_list.
splice_read() needs to consult that list otherwise it may miss data.
Align with recvmsg() and also put partially-read records onto rx_list.
tls_sw_advance_skb() is pretty pointless now and will be removed in
net-next.
Fixes: 692d7b5d1f ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 520493f66f ]
We don't support splicing control records. TLS 1.3 changes moved
the record type check into the decrypt if(). The skb may already
be decrypted and still be an alert.
Note that decrypt_skb_update() is idempotent and updates ctx->decrypted
so the if() is pointless.
Reorder the check for decryption errors with the content type check
while touching them. This part is not really a bug, because if
decryption failed in TLS 1.3 content type will be DATA, and for
TLS 1.2 it will be correct. Nevertheless its strange to touch output
before checking if the function has failed.
Fixes: fedf201e12 ("net: tls: Refactor control message handling on recv")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ce097f71 ]
It hangup when booting Loongson 3A1000 with BOTH
CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn
out to use 2-level pgtable instead of 3-level. 64KB page size
with 2-level pgtable only cover 42 bits VA, use 3-level pgtable
to cover all 48 bits VA(55 bits)
Fixes: 1e321fa917 ("MIPS64: Support of at least 48 bits of SEGBITS)
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db5e9e9e5 ]
It turns out that 'decode_configs' -> 'set_ftlb_enable' is called under
c->cputype unset, which leaves FTLB disabled on BOTH 3A2000 and 3A3000
Fix it by calling "decode_configs" after c->cputype is initialized
Fixes: da1bd29742 ("MIPS: Loongson64: Probe CPU features via CPUCFG")
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaeace6077 ]
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c024b226a4 ]
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes: 50a909db36 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ebb0c4b27 ]
The kernel_listen function in smc_listen will fail when all the available
ports are occupied. At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready. When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.
The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.
This patch restores smc->clcsock->sk->sk_data_ready with the old value.
Fixes: a60a2b1e0a ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 587acad41f ]
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes: cb9d43f677 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbae3388ea ]
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80662f4fd4 ]
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddb826c2c9 ]
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3d ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1fddc98d ]
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes: ae27e98a51 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21431f70f6 ]
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371a ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eff272dbe ]
[Why]
The HW interrupt gets disabled after GPU reset so we don't receive
notifications for HPD or AUX from DMUB - leading to timeout and
black screen with (or without) DPIA links connected.
[How]
Re-enable the interrupt after GPU reset like we do for the other
DC interrupts.
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Reviewed-by: Jude Shih <Jude.Shih@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cefcf24b4d ]
Commit 39fbef4b0f ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac13285214 ]
Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).
The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.
Fixes: fb4ee67529 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94902d849e ]
As Vincent reports in:
https://lore.kernel.org/r/20211118163417.21617-1-vincent.whitchurch@axis.com
The put_user() in schedule_tail() can get stuck in a livelock, similar
to a problem recently fixed on riscv in commit:
285a76bb2c ("riscv: evaluate put_user() arg before enabling user access")
In __raw_put_user() we have a critical section between
uaccess_ttbr0_enable() and uaccess_ttbr0_disable() where we cannot
safely call into the scheduler without having taken an exception, as
schedule() and other scheduling functions will not save/restore the
TTBR0 state. If either of the `x` or `ptr` arguments to __raw_put_user()
contain a blocking call, we may call into the scheduler within the
critical section. This can result in two problems:
1) The access within the critical section will occur without the
required TTBR0 tables installed. This will fault, and where the
required tables permit access, the access will be retried without the
required tables, resulting in a livelock.
2) When TTBR0 SW PAN is in use, check_and_switch_context() does not
modify TTBR0, leaving a stale value installed. The mappings of the
blocked task will erroneously be accessible to regular accesses in
the context of the new task. Additionally, if the tables are
subsequently freed, local TLB maintenance required to reuse the ASID
may be lost, potentially resulting in TLB corruption (e.g. in the
presence of CnP).
The same issue exists for __raw_get_user() in the critical section
between uaccess_ttbr0_enable() and uaccess_ttbr0_disable().
A similar issue exists for __get_kernel_nofault() and
__put_kernel_nofault() for the critical section between
__uaccess_enable_tco_async() and __uaccess_disable_tco_async(), as the
TCO state is not context-switched by direct calls into the scheduler.
Here the TCO state may be lost from the context of the current task,
resulting in unexpected asynchronous tag check faults. It may also be
leaked to another task, suppressing expected tag check faults.
To fix all of these cases, we must ensure that we do not directly call
into the scheduler in their respective critical sections. This patch
reworks __raw_put_user(), __raw_get_user(), __get_kernel_nofault(), and
__put_kernel_nofault(), ensuring that parameters are evaluated outside
of the critical sections. To make this requirement clear, comments are
added describing the problem, and line spaces added to separate the
critical sections from other portions of the macros.
For __raw_get_user() and __raw_put_user() the `err` parameter is
conditionally assigned to, and we must currently evaluate this in the
critical section. This behaviour is relied upon by the signal code,
which uses chains of put_user_error() and get_user_error(), checking the
return value at the end. In all cases, the `err` parameter is a plain
int rather than a more complex expression with a blocking call, so this
is safe.
In future we should try to clean up the `err` usage to remove the
potential for this to be a problem.
Aside from the changes to time of evaluation, there should be no
functional change as a result of this patch.
Reported-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20211118163417.21617-1-vincent.whitchurch@axis.com
Fixes: f253d827f3 ("arm64: uaccess: refactor __{get,put}_user")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20211122125820.55286-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 102110efdf ]
Current nvmet_try_send_ddgst() code does not check whether
all data digest bytes are transmitted, fix this by returning
-EAGAIN if all data digest bytes are not transmitted.
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd23f02f16 ]
Commit fbdc21e9b0 ("cpufreq: intel_pstate: Add Icelake servers
support in no-HWP mode") enabled the use of Intel P-State driver
for Ice Lake servers.
But it doesn't cover the case when OS can't control P-States.
Therefore, for Ice Lake server, if MSR_MISC_PWR_MGMT bits 8 or 18
are enabled, then the Intel P-State driver should exit as OS can't
control P-States.
Fixes: fbdc21e9b0 ("cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode")
Signed-off-by: Adamos Ttofari <attofari@amazon.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1b62bc1e ]
Currently mvpp2_xdp_setup won't allow attaching XDP program if
mtu > ETH_DATA_LEN (1500).
The mvpp2_change_mtu on the other hand checks whether
MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.
These two checks are semantically different.
Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
xdp.frame_sz = PAGE_SIZE;
Change the checks to check whether
mtu > MVPP2_MAX_RX_BUF_SIZE
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4e9bfb7c9 ]
Calling ipa_cmd_pipeline_clear() after stopping the channel
underlying the AP<-modem RX endpoint can lead to a deadlock.
This occurs in the ->runtime_suspend device power operation for the
IPA driver. While this callback is in progress, any other requests
for power will block until the callback returns.
Stopping the AP<-modem RX channel does not prevent the modem from
sending another packet to this endpoint. If a packet arrives for an
RX channel when the channel is stopped, an SUSPEND IPA interrupt
condition will be pending. Handling an IPA interrupt requires
power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing.
The problem occurs because a "pipeline clear" command will not
complete while such a SUSPEND interrupt condition exists. So the
SUSPEND IPA interrupt handler won't proceed until it gets power;
that won't happen until the ->runtime_suspend callback (and its
"pipeline clear" command) completes; and that can't happen while
the SUSPEND interrupt condition exists.
It turns out that in this case there is no need to use the "pipeline
clear" command. There are scenarios in which clearing the pipeline
is required while suspending, but those are not (yet) supported
upstream. So a simple fix, avoiding the potential deadlock, is to
stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend().
This removes the only user of ipa_cmd_pipeline_clear(), so get rid
of that function. It can be restored again whenever it's needed.
This is basically a manual revert along with an explanation for
commit 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()").
Fixes: 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8afc7e471a ]
The IPA setup_complete flag is set at the end of ipa_setup(), when
the setup phase of initialization has completed successfully. This
occurs as part of driver probe processing, or (if "modem-init" is
specified in the DTS file) it is triggered by the "ipa-setup-ready"
SMP2P interrupt generated by the modem.
In the latter case, it's possible for driver shutdown (or remove) to
begin while setup processing is underway, and this can't be allowed.
The problem is that the setup_complete flag is not adequate to signal
that setup is underway.
If setup_complete is set, it will never be un-set, so that case is
not a problem. But if setup_complete is false, there's a chance
setup is underway.
Because setup is triggered by an interrupt on a "modem-init" system,
there is a simple way to ensure the value of setup_complete is safe
to read. The threaded handler--if it is executing--will complete as
part of a request to disable the "ipa-modem-ready" interrupt. This
means that ipa_setup() (which is called from the handler) will run
to completion if it was underway, or will never be called otherwise.
The request to disable the "ipa-setup-ready" interrupt is currently
made within ipa_modem_stop(). Instead, disable the interrupt
outside that function in the two places it's called. In the case of
ipa_remove(), this ensures the setup_complete flag is safe to read
before we read it.
Rename ipa_smp2p_disable() to be ipa_smp2p_irq_disable_setup(), to be
more specific about its effect.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33a153100b ]
We currently maintain a "disabled" Boolean flag to determine whether
the "ipa-setup-ready" SMP2P IRQ handler does anything. That flag
must be accessed under protection of a mutex.
Instead, disable the SMP2P interrupt when requested, which prevents
the interrupt handler from ever being called. More importantly, it
synchronizes a thread disabling the interrupt with the completion of
the interrupt handler in case they run concurrently.
Use the IPA setup_complete flag rather than the disabled flag in the
handler to determine whether to ignore any interrupts arriving after
the first.
Rename the "disabled" flag to be "setup_disabled", to be specific
about its purpose.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b08b1f68 ]
When processing port up/down events generated by the device's firmware,
the driver protects itself from events reported for non-existent local
ports, but not the CPU port (local port 0), which exists, but lacks a
netdev.
This can result in a NULL pointer dereference when calling
netif_carrier_{on,off}().
Fix this by bailing early when processing an event reported for the CPU
port. Problem was only observed when running on top of a buggy emulator.
Fixes: 28b1987ef5 ("mlxsw: spectrum: Register CPU port with devlink")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606a63c978 ]
The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.
Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.
To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.
Client | Server
close() // client actively close |
smc_release() |
smc_close_active() // PEERCLOSEWAIT1 |
smc_close_final() // abort or closed = 1|
smc_cdc_get_slot_and_msg_send() |
[A] |
|smc_cdc_msg_recv_action() // ACTIVE
| queue_work(smc_close_wq, &conn->close_work)
| smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_passive_abort_received() // only in abort
|
|close() // server recv zero, close
| smc_release() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_active()
| smc_close_abort() or smc_close_final() // CLOSED
| smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action() | smc_clcsock_release()
queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT
smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free()
smc_close_passive_abort_received() // CLOSED|
smc_conn_free() |
smc_clcsock_release() |
sock_release(tcp) // passive close clc |
Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84e1d0bf1d ]
If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57bbeacdbe ]
We observed the following deadlock in the stress test under low
memory scenario:
Thread A Thread B
- erofs_shrink_scan
- erofs_try_to_release_workgroup
- erofs_workgroup_try_to_freeze -- A
- z_erofs_do_read_page
- z_erofs_collection_begin
- z_erofs_register_collection
- erofs_insert_workgroup
- xa_lock(&sbi->managed_pslots) -- B
- erofs_workgroup_get
- erofs_wait_on_workgroup_freezed -- A
- xa_erase
- xa_lock(&sbi->managed_pslots) -- B
To fix this, it needs to hold xa_lock before freezing the workgroup
since xarray will be touched then. So let's hold the lock before
accessing each workgroup, just like what we did with the radix tree
before.
[ Gao Xiang: Jianhua Hao also reports this issue at
https://lore.kernel.org/r/b10b85df30694bac8aadfe43537c897a@xiaomi.com ]
Link: https://lore.kernel.org/r/20211118135844.3559-1-huangjianan@oppo.com
Fixes: 64094a0441 ("erofs: convert workstn to XArray")
Reviewed-by: Chao Yu <chao@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Huang Jianan <huangjianan@oppo.com>
Reported-by: Jianhua Hao <haojianhua1@xiaomi.com>
Signed-off-by: Gao Xiang <xiang@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
