[ Upstream commit 17a0f3acdc ]
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fd45e79e8 ]
The AST2600 when using the i210 NIC over NC-SI has been observed to
produce incorrect checksum results with specific MTU values. This was
first observed when sending data across a long distance set of networks.
On a local network, the following test was performed using a 1MB file of
random data.
On the receiver run this script:
#!/bin/bash
while [ 1 ]; do
# Zero the stats
nstat -r > /dev/null
nc -l 9899 > test-file
# Check for checksum errors
TcpInCsumErrors=$(nstat | grep TcpInCsumErrors)
if [ -z "$TcpInCsumErrors" ]; then
echo No TcpInCsumErrors
else
echo TcpInCsumErrors = $TcpInCsumErrors
fi
done
On an AST2600 system:
# nc <IP of receiver host> 9899 < test-file
The test was repeated with various MTU values:
# ip link set mtu 1410 dev eth0
The observed results:
1500 - good
1434 - bad
1400 - good
1410 - bad
1420 - good
The test was repeated after disabling tx checksumming:
# ethtool -K eth0 tx-checksumming off
And all MTU values tested resulted in transfers without error.
An issue with the driver cannot be ruled out, however there has been no
bug discovered so far.
David has done the work to take the original bug report of slow data
transfer between long distance connections and triaged it down to this
test case.
The vendor suspects this this is a hardware issue when using NC-SI. The
fixes line refers to the patch that introduced AST2600 support.
Reported-by: David Wilder <wilder@us.ibm.com>
Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015c44d7bf ]
Since the recent introduction supporting the SM3 and SM4 hash algos for IPsec, the kernel
produces invalid pfkey acquire messages, when these encryption modules are disabled. This
happens because the availability of the algos wasn't checked in all necessary functions.
This patch adds these checks.
Signed-off-by: Thomas Bartschies <thomas.bartschies@cvk.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa8785e593 ]
Change suniv f1c100s pinctrl,PD14 multiplexing function lvds1 to uart2
When the pin PD13 and PD14 is setting up to uart2 function in dts,
there's an error occurred:
1c20800.pinctrl: unsupported function uart2 on pin PD14
Because 'uart2' is not any one multiplexing option of PD14,
and pinctrl don't know how to configure it.
So change the pin PD14 lvds1 function to uart2.
Signed-off-by: IotaHydrae <writeforever@foxmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/tencent_70C1308DDA794C81CAEF389049055BACEC09@qq.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1bbc21785b upstream.
Currently the sysfs interface maps the BERT error region as "memory"
(through acpi_os_map_memory()) in order to copy the error records into
memory buffers through memory operations (eg memory_read_from_buffer()).
The OS system cannot detect whether the BERT error region is part of
system RAM or it is "device memory" (eg BMC memory) and therefore it
cannot detect which memory attributes the bus to memory support (and
corresponding kernel mapping, unless firmware provides the required
information).
The acpi_os_map_memory() arch backend implementation determines the
mapping attributes. On arm64, if the BERT error region is not present in
the EFI memory map, the error region is mapped as device-nGnRnE; this
triggers alignment faults since memcpy unaligned accesses are not
allowed in device-nGnRnE regions.
The ACPI sysfs code cannot therefore map by default the BERT error
region with memory semantics but should use a safer default.
Change the sysfs code to map the BERT error region as MMIO (through
acpi_os_map_iomem()) and use the memcpy_fromio() interface to read the
error region into the kernel buffer.
Link: https://lore.kernel.org/linux-arm-kernel/31ffe8fc-f5ee-2858-26c5-0fd8bdd68702@arm.com
Link: https://lore.kernel.org/linux-acpi/CAJZ5v0g+OVbhuUUDrLUCfX_mVqY_e8ubgLTU98=jfjTeb4t+Pw@mail.gmail.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Veronika Kabatova <vkabatov@redhat.com>
Tested-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd56d7d89 upstream.
Sparse is not happy about address space in use in acpi_data_show():
drivers/acpi/sysfs.c:428:14: warning: incorrect type in assignment (different address spaces)
drivers/acpi/sysfs.c:428:14: expected void [noderef] __iomem *base
drivers/acpi/sysfs.c:428:14: got void *
drivers/acpi/sysfs.c:431:59: warning: incorrect type in argument 4 (different address spaces)
drivers/acpi/sysfs.c:431:59: expected void const *from
drivers/acpi/sysfs.c:431:59: got void [noderef] __iomem *base
drivers/acpi/sysfs.c:433:30: warning: incorrect type in argument 1 (different address spaces)
drivers/acpi/sysfs.c:433:30: expected void *logical_address
drivers/acpi/sysfs.c:433:30: got void [noderef] __iomem *base
Indeed, acpi_os_map_memory() returns a void pointer with dropped specific
address space. Hence, we don't need to carry out __iomem in acpi_data_show().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a28dce222 upstream.
Before the video device node is registered, the v4l2_dev.mdev
pointer must be set in order to correctly associate the video
device with the media device. Move the initialization of the
media device up.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d057560b upstream.
SipHash replaced MD5 in secure_ipv{4,6}_port_ephemeral() via commit
7cd23e5300 ("secure_seq: use SipHash in place of MD5"), but the output
remained truncated to 32-bit only. In order to exploit more bits from the
hash, let's make the functions return the full 64-bit of siphash_3u32().
We also make sure the port offset calculation in __inet_hash_connect()
remains done on 32-bit to avoid the need for div_u64_rem() and an extra
cost on 32-bit systems.
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il>
Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il>
Cc: Amit Klein <aksecurity@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[SG: Adjusted context]
Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 190cc82489 upstream.
RFC 6056 (Recommendations for Transport-Protocol Port Randomization)
provides good summary of why source selection needs extra care.
David Dworken reminded us that linux implements Algorithm 3
as described in RFC 6056 3.3.3
Quoting David :
In the context of the web, this creates an interesting info leak where
websites can count how many TCP connections a user's computer is
establishing over time. For example, this allows a website to count
exactly how many subresources a third party website loaded.
This also allows:
- Distinguishing between different users behind a VPN based on
distinct source port ranges.
- Tracking users over time across multiple networks.
- Covert communication channels between different browsers/browser
profiles running on the same computer
- Tracking what applications are running on a computer based on
the pattern of how fast source ports are getting incremented.
Section 3.3.4 describes an enhancement, that reduces
attackers ability to use the basic information currently
stored into the shared 'u32 hint'.
This change also decreases collision rate when
multiple applications need to connect() to
different destinations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24ef83f6e3 upstream.
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code has a check to prevent read overflow but it needs another
check to prevent writing beyond the end of the ->Ssid[] array.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Denis Efremov (Oracle) <efremov@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0815b3e0 upstream.
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then
PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to
XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI
layer.
This can lead to a situation where the PCI/MSI layer masks an MSI[-X]
interrupt and the hypervisor grants the write despite the fact that it
already requested the interrupt. As a consequence interrupt delivery on the
affected device is not happening ever.
Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests
already.
Fixes: 809f9267bb ("xen: map MSIs into pirqs")
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: Dusty Mabe <dustymabe@redhat.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Noah Meyerhans <noahm@debian.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuaduxj5.ffs@tglx
[nmeyerha@amazon.com: backported to 5.4]
Signed-off-by: Noah Meyerhans <nmeyerha@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eadb2f47a3 upstream.
KGDB and KDB allow read and write access to kernel memory, and thus
should be restricted during lockdown. An attacker with access to a
serial port (for example, via a hypervisor console, which some cloud
vendors provide over the network) could trigger the debugger so it is
important that the debugger respect the lockdown mode when/if it is
triggered.
Fix this by integrating lockdown into kdb's existing permissions
mechanism. Unfortunately kgdb does not have any permissions mechanism
(although it certainly could be added later) so, for now, kgdb is simply
and brutally disabled by immediately exiting the gdb stub without taking
any action.
For lockdowns established early in the boot (e.g. the normal case) then
this should be fine but on systems where kgdb has set breakpoints before
the lockdown is enacted than "bad things" will happen.
CVE: CVE-2022-21499
Co-developed-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2aeb8c86d4 ]
If a callback break occurs (change notification), afs_getattr() needs to
issue an FS.FetchStatus RPC operation to update the status of the file
being examined by the stat-family of system calls.
Fix afs_getattr() to do this if AFS_VNODE_CB_PROMISED has been cleared
on a vnode by a callback break. Skip this if AT_STATX_DONT_SYNC is set.
This can be tested by appending to a file on one AFS client and then
using "stat -L" to examine its length on a machine running kafs. This
can also be watched through tracing on the kafs machine. The callback
break is seen:
kworker/1:1-46 [001] ..... 978.910812: afs_cb_call: c=0000005f YFSCB.CallBack
kworker/1:1-46 [001] ...1. 978.910829: afs_cb_break: 100058:23b4c:242d2c2 b=2 s=1 break-cb
kworker/1:1-46 [001] ..... 978.911062: afs_call_done: c=0000005f ret=0 ab=0 [0000000082994ead]
And then the stat command generated no traffic if unpatched, but with
this change a call to fetch the status can be observed:
stat-4471 [000] ..... 986.744122: afs_make_fs_call: c=000000ab 100058:023b4c:242d2c2 YFS.FetchStatus
stat-4471 [000] ..... 986.745578: afs_call_done: c=000000ab ret=0 ab=0 [0000000087fc8c84]
Fixes: 08e0e7c82e ("[AF_RXRPC]: Make the in-kernel AFS filesystem use AF_RXRPC.")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
Tested-by: kafs-testing+fedora34_64checkkafs-build-496@auristor.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216010
Link: https://lore.kernel.org/r/165308359800.162686.14122417881564420962.stgit@warthog.procyon.org.uk/ # v1
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9af9dcf11b upstream.
The asm_cpu_bringup_and_idle() function is required to push the return
value on the stack in order to make ORC happy, but the only reason
objtool doesn't complain is because of a happy accident.
The thing is that asm_cpu_bringup_and_idle() doesn't return, so
validate_branch() never terminates and falls through to the next
function, which in the normal case is the hypercall_page. And that, as
it happens, is 4095 NOPs and a RET.
Make asm_cpu_bringup_and_idle() terminate on it's own, by making the
function it calls as a dead-end. This way we no longer rely on what
code happens to come after.
Fixes: c3881eb58d ("x86/xen: Make the secondary CPU idle tasks reliable")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Link: https://lore.kernel.org/r/20210624095147.693801717@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cb7df64c7 upstream.
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. Moreover,
the consumer driver of the mentioned clock might gate it and leave
the ECSPI2 (the true owner of that gate) hanging. So lets use the
audio_mclk_post_div, which is the parent.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
[ps: backport to 5.4]
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 581dd69830 upstream.
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Previously, Android configurations were not setting up the
firmware_class.path command line argument and were relying on the
userspace fallback mechanism. In this case, the security context of the
userspace daemon (i.e. ueventd) was consistently used to read firmware
files. More Android devices are now found to set firmware_class.path
which gives the kernel the opportunity to read the firmware directly
(via kernel_read_file_from_path_initns). In this scenario, the current
process credentials were used, even if unrelated to the loading of the
firmware file.
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Cc: <stable@vger.kernel.org> # 5.10
Reviewed-by: Paul Moore <paul@paul-moore.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20220502004952.3970800-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47f753c110 upstream.
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 866663b7b5 upstream.
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Fixes: 2705dfb209 ("block: fix discard request merge")
Link: https://lore.kernel.org/r/20210729034226.1591070-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4920d42ce upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e71b7f1f44 ]
The 'ping' utility is able to manage two kind of sockets (raw or icmp),
depending on the sysctl ping_group_range. By default, ping_group_range is
set to '1 0', which forces ping to use an ip raw socket.
Let's replay the ping tests by allowing 'ping' to use the ip icmp socket.
After the previous patch, ipv4 tests results are the same with both kinds
of socket. For ipv6, there are a lot a new failures (the previous patch
fixes only two cases).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26f9ce5381 ]
Aborting commands that have already been sent to the firmware can
cause BUG in qlt_free_cmd(): BUG_ON(cmd->sg_mapped)
For instance:
- Command passes rdx_to_xfer state, maps sgl, sends to the firmware
- Reset occurs, qla2xxx performs ISP error recovery, aborts the command
- Target stack calls qlt_abort_cmd() and then qlt_free_cmd()
- BUG_ON(cmd->sg_mapped) in qlt_free_cmd() occurs because sgl was not
unmapped
Thus, unmap sgl in qlt_abort_cmd() for commands with the aborted flag set.
Link: https://lore.kernel.org/r/AS8PR10MB4952D545F84B6B1DFD39EC1E9DEE9@AS8PR10MB4952.EURPRD10.PROD.OUTLOOK.COM
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Gleb Chesnokov <Chesnokov.G@raidix.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8ac1c4784 ]
The compilation on s390 results in this error:
# make DEBUG=y bench/numa.o
...
bench/numa.c: In function ‘__bench_numa’:
bench/numa.c:1749:81: error: ‘%d’ directive output may be truncated
writing between 1 and 11 bytes into a region of size between
10 and 20 [-Werror=format-truncation=]
1749 | snprintf(tname, sizeof(tname), "process%d:thread%d", p, t);
^~
...
bench/numa.c:1749:64: note: directive argument in the range
[-2147483647, 2147483646]
...
#
The maximum length of the %d replacement is 11 characters because of the
negative sign. Therefore extend the array by two more characters.
Output after:
# make DEBUG=y bench/numa.o > /dev/null 2>&1; ll bench/numa.o
-rw-r--r-- 1 root root 418320 May 19 09:11 bench/numa.o
#
Fixes: 3aff8ba0a4 ("perf bench numa: Avoid possible truncation when using snprintf()")
Suggested-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20220520081158.2990006-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bf3ac466f ]
For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.
Fixes: 659d8a6231 ("gpio: vf610: add imx7ulp support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb3abdf22 ]
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: f1c2eddf4c ("bridge: switchdev: Use an helper to clear forward mark")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942d2ad5d2 ]
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfb301997 ]
In Thumb2, 'b . + 4' produces a branch instruction that uses a narrow
encoding, and so it does not jump to the following instruction as
expected. So use W(b) instead.
Fixes: 6c7cb60bff ("ARM: fix Thumb2 regression with Spectre BHB")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc14aa94c ]
The Spectre-BHB mitigations were inadvertently left disabled for
Cortex-A15, due to the fact that cpu_v7_bugs_init() is not called in
that case. So fix that.
Fixes: b9baf5c8c5 ("ARM: Spectre-BHB workaround")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dc2a5a8f6 ]
If skb_clone() returns null pointer, pfkey_broadcast() will
return error.
Therefore, it should be better to check the return value of
pfkey_broadcast() and return error if fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf6e34c8c2 ]
LRO is incompatible and mutually exclusive with XDP. However, the needed
checks are only made when enabling XDP. If LRO is enabled when XDP is
already active, the command will succeed, and XDP will be skipped in the
data path, although still enabled.
This commit fixes the bug by checking the XDP status in
mlx5e_fix_features and disabling LRO if XDP is enabled.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23dd458135 ]
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
(interrupt context 1)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_skb_alloc(..., GFP_KERNEL) //may sleep
(interrupt context 2)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_send_data
nci_queue_tx_data_frags
nci_skb_alloc(..., GFP_KERNEL) //may sleep
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: ed06aeefda ("nfc: st-nci: Rename st21nfcb to st-nci")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5361448e45 ]
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
This has been spotted by smatch.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31b6298fd8 ]
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8 ("ice: ignore dropped packets during init")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf410cb74 ]
In vmxnet3_rq_create(), when dma_alloc_coherent() fails,
vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then
vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all()
-> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls
vmxnet3_force_close() -> dev_close() in error handling code. And the driver
calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all()
-> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(),
rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing
a NULL pointer dereference.
To fix this possible bug, an if statement is added to check whether
rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so.
The error log in our fault-injection testing is shown as follows:
[ 65.220135] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 65.222633] RIP: 0010:vmxnet3_rq_cleanup_all+0x396/0x4e0 [vmxnet3]
...
[ 65.227977] Call Trace:
...
[ 65.228262] vmxnet3_quiesce_dev+0x80f/0x8a0 [vmxnet3]
[ 65.228580] vmxnet3_close+0x2c4/0x3f0 [vmxnet3]
[ 65.228866] __dev_close_many+0x288/0x350
[ 65.229607] dev_close_many+0xa4/0x480
[ 65.231124] dev_close+0x138/0x230
[ 65.231933] vmxnet3_force_close+0x1f0/0x240 [vmxnet3]
[ 65.232248] vmxnet3_change_mtu+0x75d/0x920 [vmxnet3]
...
Fixes: d1a890fa37 ("net: VMware virtual Ethernet NIC driver: vmxnet3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Zixuan Fu <r33s3n6@gmail.com>
Link: https://lore.kernel.org/r/20220514050711.2636709-1-r33s3n6@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d42d54a7d ]
syzbot was able to trigger an Out-of-Bound on the pedit action:
UBSAN: shift-out-of-bounds in net/sched/act_pedit.c:238:43
shift exponent 1400735974 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 3606 Comm: syz-executor151 Not tainted 5.18.0-rc5-syzkaller-00165-g810c2f0a3f86 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x50 lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x187 lib/ubsan.c:322
tcf_pedit_init.cold+0x1a/0x1f net/sched/act_pedit.c:238
tcf_action_init_1+0x414/0x690 net/sched/act_api.c:1367
tcf_action_init+0x530/0x8d0 net/sched/act_api.c:1432
tcf_action_add+0xf9/0x480 net/sched/act_api.c:1956
tc_ctl_action+0x346/0x470 net/sched/act_api.c:2015
rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5993
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:725
____sys_sendmsg+0x6e2/0x800 net/socket.c:2413
___sys_sendmsg+0xf3/0x170 net/socket.c:2467
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fe36e9e1b59
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffef796fe88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe36e9e1b59
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
RBP: 00007fe36e9a5d00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe36e9a5d90
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com
Fixes: 8b796475fd ("net/sched: act_pedit: really ensure the skb is writable")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9500acc631 ]
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
