[ Upstream commit b89405b610 ]
When dt_to_map_one_config() is called with a pinctrl_dev passed
in, it should only be using this if the node being looked up
is a hog. The code was always using the passed pinctrl_dev
without checking whether the dt node referred to it.
A pin controller can have pinctrl-n dependencies on other pin
controllers in these cases:
- the pin controller hardware is external, for example I2C, so
needs other pin controller(s) to be setup to communicate with
the hardware device.
- it is a child of a composite MFD so its of_node is shared with
the parent MFD and other children of that MFD. Any part of that
MFD could have dependencies on other pin controllers.
Because of this, dt_to_map_one_config() can't assume that if it
has a pinctrl_dev passed in then the node it looks up must be
a hog. It could be a reference to some other pin controller.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c829f47e3 ]
If devm_reset_control_get_exclusive() fails, asm9260_wdt_probe()
returns immediately. But clks has been already enabled at that point,
so it is required to disable them or to move the code around.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e081628d5 ]
This patch fixes an issue that a race condition happens between a client
driver and the rcar-dmac driver:
- The rcar_dmac_isr_transfer_end() is called.
- The done list appears, and desc.running is the next active list.
- rcar_dmac_chan_get_residue() is called by a client driver before
rcar_dmac_isr_channel_thread() is called.
- The rcar_dmac_chan_get_residue() will not find any descriptors.
- And, the following WARNING happens:
WARN(1, "No descriptor for cookie!");
The sh-sci driver with HSCIF (921,600bps) on R-Car H3 can cause this
situation.
So, this patch checks the done lists in rcar_dmac_chan_get_residue()
and returns zero if the done lists has the argument cookie.
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1330fc3532 ]
This patch fixes the below warnings with new glibc and gcc:
hv_vss_daemon.c:100:13: warning: In the GNU C Library, "major" is defined
by <sys/sysmacros.h>. For historical compatibility, it is currently
defined by <sys/types.h> as well, but we plan to remove this soon.
To use "major", include <sys/sysmacros.h> directly.
hv_fcopy_daemon.c:42:2: note: 'snprintf' output between 2 and 1040
bytes into a destination of size 260
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e7a66a8b5 ]
The following happens when connection a DVI output driven
from the SiI9022 using a DVI-to-VGA adapter plug:
i2c i2c-0: sendbytes: NAK bailout.
i2c i2c-0: sendbytes: NAK bailout.
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305101702.13441-1-linus.walleij@linaro.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e2c177ca8 ]
In slave_update() of vmaster code ignores the error from the slave
get() callback and copies the values. It's not only about the missing
error code but also that this may potentially lead to a leak of
uninitialized variables when the slave get() don't clear them.
This patch fixes slave_update() not to copy the potentially
uninitialized values when an error is returned from the slave get()
callback, and to propagate the error value properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a5169add9 ]
IRQ parameters for the SoC devices connected directly to I/O APIC lines
(without PCI IRQ routing) may be specified in the Device Tree.
Called from DT IRQ parser, irq_create_fwspec_mapping() calls
irq_domain_alloc_irqs() with a pointer to irq_fwspec structure as @arg.
But x86-specific DT IRQ allocation code casts @arg to of_phandle_args
structure pointer and crashes trying to read the IRQ parameters. The
function was not converted when the mapping descriptor was changed to
irq_fwspec in the generic irqdomain code.
Fixes: 11e4438ee3 ("irqdomain: Introduce a firmware-specific IRQ specifier structure")
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: https://lkml.kernel.org/r/a234dee27ea60ce76141872da0d6bdb378b2a9ee.1520450752.git.ivan.gorinov@intel.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 174d1232eb ]
The chunk size of allocations in __gfs2_fallocate is calculated
incorrectly. The size can collapse, causing __gfs2_fallocate to
allocate one block at a time, which is very inefficient. This needs
fixing in two places:
In gfs2_quota_lock_check, always set ap->allowed to UINT_MAX to indicate
that there is no quota limit. This fixes callers that rely on
ap->allowed to be set even when quotas are off.
In __gfs2_fallocate, reset max_blks to UINT_MAX in each iteration of the
loop to make sure that allocation limits from one resource group won't
spill over into another resource group.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90c29ed762 ]
hdr.len includes both the size of the header and the fragment, so using
this when stepping through the firmware causes us to skip 16 bytes every
chunk of 3072 bytes; causing only the first fragment to actually be
valid data.
Instead use fragment size steps through the firmware blob.
Fixes: ea7a1f275c ("soc: qcom: Introduce WCNSS_CTRL SMD client")
Reported-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d31fc13fdc ]
There is a bug when reading event->count with large PEBS enabled.
Here is an example:
# ./read_count
0x71f0
0x122c0
0x1000000001c54
0x100000001257d
0x200000000bdc5
In fixed period mode, the auto-reload mechanism could be enabled for
PEBS events, but the calculation of event->count does not take the
auto-reload values into account.
Anyone who reads event->count will get the wrong result, e.g x86_pmu_read().
This bug was introduced with the auto-reload mechanism enabled since
commit:
851559e35f ("perf/x86/intel: Use the PEBS auto reload mechanism when possible")
Introduce intel_pmu_save_and_restart_reload() to calculate the
event->count only for auto-reload.
Since the counter increments a negative counter value and overflows on
the sign switch, giving the interval:
[-period, 0]
the difference between two consequtive reads is:
A) value2 - value1;
when no overflows have happened in between,
B) (0 - value1) + (value2 - (-period));
when one overflow happened in between,
C) (0 - value1) + (n - 1) * (period) + (value2 - (-period));
when @n overflows happened in between.
Here A) is the obvious difference, B) is the extension to the discrete
interval, where the first term is to the top of the interval and the
second term is from the bottom of the next interval and C) the extension
to multiple intervals, where the middle term is the whole intervals
covered.
The equation for all cases is:
value2 - value1 + n * period
Previously the event->count is updated right before the sample output.
But for case A, there is no PEBS record ready. It needs to be specially
handled.
Remove the auto-reload code from x86_perf_event_set_period() since
we'll not longer call that function in this case.
Based-on-code-from: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Fixes: 851559e35f ("perf/x86/intel: Use the PEBS auto reload mechanism when possible")
Link: http://lkml.kernel.org/r/1518474035-21006-2-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2bbea6e117 ]
when mounting an ISO filesystem sometimes (very rarely)
the system hangs because of a race condition between two tasks.
PID: 6766 TASK: ffff88007b2a6dd0 CPU: 0 COMMAND: "mount"
#0 [ffff880078447ae0] __schedule at ffffffff8168d605
#1 [ffff880078447b48] schedule_preempt_disabled at ffffffff8168ed49
#2 [ffff880078447b58] __mutex_lock_slowpath at ffffffff8168c995
#3 [ffff880078447bb8] mutex_lock at ffffffff8168bdef
#4 [ffff880078447bd0] sr_block_ioctl at ffffffffa00b6818 [sr_mod]
#5 [ffff880078447c10] blkdev_ioctl at ffffffff812fea50
#6 [ffff880078447c70] ioctl_by_bdev at ffffffff8123a8b3
#7 [ffff880078447c90] isofs_fill_super at ffffffffa04fb1e1 [isofs]
#8 [ffff880078447da8] mount_bdev at ffffffff81202570
#9 [ffff880078447e18] isofs_mount at ffffffffa04f9828 [isofs]
#10 [ffff880078447e28] mount_fs at ffffffff81202d09
#11 [ffff880078447e70] vfs_kern_mount at ffffffff8121ea8f
#12 [ffff880078447ea8] do_mount at ffffffff81220fee
#13 [ffff880078447f28] sys_mount at ffffffff812218d6
#14 [ffff880078447f80] system_call_fastpath at ffffffff81698c49
RIP: 00007fd9ea914e9a RSP: 00007ffd5d9bf648 RFLAGS: 00010246
RAX: 00000000000000a5 RBX: ffffffff81698c49 RCX: 0000000000000010
RDX: 00007fd9ec2bc210 RSI: 00007fd9ec2bc290 RDI: 00007fd9ec2bcf30
RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000010
R10: 00000000c0ed0001 R11: 0000000000000206 R12: 00007fd9ec2bc040
R13: 00007fd9eb6b2380 R14: 00007fd9ec2bc210 R15: 00007fd9ec2bcf30
ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b
This task was trying to mount the cdrom. It allocated and configured a
super_block struct and owned the write-lock for the super_block->s_umount
rwsem. While exclusively owning the s_umount lock, it called
sr_block_ioctl and waited to acquire the global sr_mutex lock.
PID: 6785 TASK: ffff880078720fb0 CPU: 0 COMMAND: "systemd-udevd"
#0 [ffff880078417898] __schedule at ffffffff8168d605
#1 [ffff880078417900] schedule at ffffffff8168dc59
#2 [ffff880078417910] rwsem_down_read_failed at ffffffff8168f605
#3 [ffff880078417980] call_rwsem_down_read_failed at ffffffff81328838
#4 [ffff8800784179d0] down_read at ffffffff8168cde0
#5 [ffff8800784179e8] get_super at ffffffff81201cc7
#6 [ffff880078417a10] __invalidate_device at ffffffff8123a8de
#7 [ffff880078417a40] flush_disk at ffffffff8123a94b
#8 [ffff880078417a88] check_disk_change at ffffffff8123ab50
#9 [ffff880078417ab0] cdrom_open at ffffffffa00a29e1 [cdrom]
#10 [ffff880078417b68] sr_block_open at ffffffffa00b6f9b [sr_mod]
#11 [ffff880078417b98] __blkdev_get at ffffffff8123ba86
#12 [ffff880078417bf0] blkdev_get at ffffffff8123bd65
#13 [ffff880078417c78] blkdev_open at ffffffff8123bf9b
#14 [ffff880078417c90] do_dentry_open at ffffffff811fc7f7
#15 [ffff880078417cd8] vfs_open at ffffffff811fc9cf
#16 [ffff880078417d00] do_last at ffffffff8120d53d
#17 [ffff880078417db0] path_openat at ffffffff8120e6b2
#18 [ffff880078417e48] do_filp_open at ffffffff8121082b
#19 [ffff880078417f18] do_sys_open at ffffffff811fdd33
#20 [ffff880078417f70] sys_open at ffffffff811fde4e
#21 [ffff880078417f80] system_call_fastpath at ffffffff81698c49
RIP: 00007f29438b0c20 RSP: 00007ffc76624b78 RFLAGS: 00010246
RAX: 0000000000000002 RBX: ffffffff81698c49 RCX: 0000000000000000
RDX: 00007f2944a5fa70 RSI: 00000000000a0800 RDI: 00007f2944a5fa70
RBP: 00007f2944a5f540 R8: 0000000000000000 R9: 0000000000000020
R10: 00007f2943614c40 R11: 0000000000000246 R12: ffffffff811fde4e
R13: ffff880078417f78 R14: 000000000000000c R15: 00007f2944a4b010
ORIG_RAX: 0000000000000002 CS: 0033 SS: 002b
This task tried to open the cdrom device, the sr_block_open function
acquired the global sr_mutex lock. The call to check_disk_change()
then saw an event flag indicating a possible media change and tried
to flush any cached data for the device.
As part of the flush, it tried to acquire the super_block->s_umount
lock associated with the cdrom device.
This was the same super_block as created and locked by the previous task.
The first task acquires the s_umount lock and then the sr_mutex_lock;
the second task acquires the sr_mutex_lock and then the s_umount lock.
This patch fixes the issue by moving check_disk_change() out of
cdrom_open() and let the caller take care of it.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ecb29abd4c ]
A negative page register value means that no page needs to be
selected. This is used by status register read operations and needs
to be accepted. The failure to do so so results in missed status
and limit registers.
Fixes: da8e48ab48 ("hwmon: (pmbus) Always call _pmbus_read_byte in core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a46f8cd696 ]
A negative page register value means that no page needs to be
selected. This is used by status register evaluations and needs
to be accepted.
Fixes: da8e48ab48 ("hwmon: (pmbus) Always call _pmbus_read_byte in core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e5b127d6f ]
Mark reported his arm64 perf fuzzer runs sometimes splat like:
armv8pmu_read_counter+0x1e8/0x2d8
armpmu_event_update+0x8c/0x188
armpmu_read+0xc/0x18
perf_output_read+0x550/0x11e8
perf_event_read_event+0x1d0/0x248
perf_event_exit_task+0x468/0xbb8
do_exit+0x690/0x1310
do_group_exit+0xd0/0x2b0
get_signal+0x2e8/0x17a8
do_signal+0x144/0x4f8
do_notify_resume+0x148/0x1e8
work_pending+0x8/0x14
which asserts that we only call pmu::read() on ACTIVE events.
The above callchain does:
perf_event_exit_task()
perf_event_exit_task_context()
task_ctx_sched_out() // INACTIVE
perf_event_exit_event()
perf_event_set_state(EXIT) // EXIT
sync_child_event()
perf_event_read_event()
perf_output_read()
perf_output_read_group()
leader->pmu->read()
Which results in doing a pmu::read() on an !ACTIVE event.
I _think_ this is 'new' since we added attr.inherit_stat, which added
the perf_event_read_event() to the exit path, without that
perf_event_read_output() would only trigger from samples and for
@event to trigger a sample, it's leader _must_ be ACTIVE too.
Still, adding this check makes it consistent with the @sub case for
the siblings.
Reported-and-Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66ec32fc7c ]
max17042_get_status uses the core power_supply_am_i_supplied. That
function relies on DT properties to figure out the power supply
topology, and will error out without DT.
Fixes max17042 battery status being reported as "unknown".
Signed-off-by: Pierre Bourdon <delroth@google.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf617f7a92 ]
If noextent_cache mount option is on, we will never initialize extent tree
in inode, but still we're going to access it in f2fs_drop_extent_tree,
result in kernel panic as below:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000038
IP: _raw_write_lock+0xc/0x30
Call Trace:
? f2fs_drop_extent_tree+0x41/0x70 [f2fs]
f2fs_fallocate+0x5a0/0xdd0 [f2fs]
? common_file_perm+0x47/0xc0
? apparmor_file_permission+0x1a/0x20
vfs_fallocate+0x15b/0x290
SyS_fallocate+0x44/0x70
do_syscall_64+0x6e/0x160
entry_SYSCALL64_slow_path+0x25/0x25
This patch fixes to check extent cache status before using in
f2fs_drop_extent_tree.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd36d7a17f ]
Once CP_TRIMMED_FLAG is set, after a reboot, we will never issue discard
before LBA becomes invalid again, fix it by clearing the flag in
checkpoint without CP_TRIMMED reason.
Fixes: 1f43e2ad7b ("f2fs: introduce CP_TRIMMED_FLAG to avoid unneeded discard")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17cd07ae95 ]
As Jayashree Mohan reported:
A simple workload to reproduce this would be :
1. create foo
2. Write (8K - 16K) // foo size = 16K now
3. fsync()
4. falloc zero_range , keep_size (4202496 - 4210688) // foo size must be 16K
5. fdatasync()
Crash now
On recovery, we see that the file size is 4210688 and not 16K, which
violates the semantics of keep_size flag. We have a test case to
reproduce this using CrashMonkey on 4.15 kernel. Try this out by
simply running :
./c_harness -f /dev/sda -d /dev/cow_ram0 -t f2fs -e 102400 -P -v
tests/generic_468_zero.so
The root cause is that we miss to set KEEP_SIZE bit correctly in zero_range
when zeroing block cross EOF with FALLOC_FL_KEEP_SIZE, let's fix this
missing case.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94322ed8e8 ]
PSL9D doesn't have a data-cache that needs to be flushed before
resetting the card. However when cxl tries to flush data-cache on such
a card, it times-out as PSL_Control register never indicates flush
operation complete due to missing data-cache. This is usually
indicated in the kernel logs with this message:
"WARNING: cache flush timed out"
To fix this the patch checks PSL_Debug register CDC-Field(BIT:27)
which indicates the absence of a data-cache and sets a flag
'no_data_cache' in 'struct cxl_native' to indicate this. When
cxl_data_cache_flush() is called it checks the flag and if set bails
out early without requesting a data-cache flush operation to the PSL.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b74e2a9b3 ]
When sending TLB invalidates to the NPU we need to send extra flushes due
to a hardware issue. The original implementation would lock the all the
ATSD MMIO registers sequentially before unlocking and relocking each of
them sequentially to do the extra flush.
This introduced a deadlock as it is possible for one thread to hold one
ATSD register whilst waiting for another register to be freed while the
other thread is holding that register waiting for the one in the first
thread to be freed.
For example if there are two threads and two ATSD registers:
Thread A Thread B
----------------------
Acquire 1
Acquire 2
Release 1 Acquire 1
Wait 1 Wait 2
Both threads will be stuck waiting to acquire a register resulting in an
RCU stall warning or soft lockup.
This patch solves the deadlock by refactoring the code to ensure registers
are not released between flushes and to ensure all registers are either
acquired or released together and in order.
Fixes: bbd5ff50af ("powerpc/powernv/npu-dma: Add explicit flush when sending an ATSD")
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f5246862f8 ]
In commit 4f8b50bbbe ("irq_work, ppc: Fix up arch hooks") a new
function arch_irq_work_raise() was added without a prototype in header
irq_work.h.
Fix the following warning (treated as error in W=1):
arch/powerpc/kernel/time.c:523:6: error: no previous prototype for ‘arch_irq_work_raise’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2fc8db691 ]
Assert RESET_SYSTEM bit for any reset and set MODE field from reset
type.
The watchdog control register has a RESET_SYSTEM bit that is really
closer to activate a reset, and RESET_SYSTEM_MODE field that chooses
how much to reset.
Before this patch, a node without these optional property would do a
SOC reset, but a node with properties requesting a cpu or SOC reset
would do nothing and a node requesting a system reset would do a
SOC reset.
Fixes: b7f0b8ad25 ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a81abbb412 ]
RK3399 has rst_pulse_length in CONTROL_REG[4:2], determining the length
of pulse to issue for system reset. We shouldn't clobber this value,
because that might make the system reset ineffective. On RK3399, we're
seeing that a value of 000b (meaning 2 cycles) yields an unreliable
(partial?) reset, and so we only fully reset after the watchdog fires a
second time. If we retain the system default (010b, or 8 clock cycles),
then the watchdog reset is much more reliable.
Read-modify-write retains the system value and improves reset
reliability.
It seems we were intentionally clobbering the response mode previously,
to ensure we performed a system reset (we don't support an interrupt
notification), so retain that explicitly.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5775b843a6 ]
We leave PCI devices not bound to a driver in D0 during runtime suspend.
But they may have a parent which is bound and can be transitioned to
D3cold at runtime. Once the parent goes to D3cold, the unbound child
may go to D3cold as well. When the child goes to D3cold, its internal
state, including configuration of BARs, MSI, ASPM, MPS, etc., is lost.
One example are recent hybrid graphics laptops which cut power to the
discrete GPU when the root port above it goes to ACPI power state D3.
Users may provoke this by unbinding the GPU driver and allowing runtime
PM on the GPU via sysfs: The PM core will then treat the GPU as
"suspended", which in turn allows the root port to runtime suspend,
causing the power resources listed in its _PR3 object to be powered off.
The GPU's BARs will be uninitialized when a driver later probes it.
Another example are hybrid graphics laptops where the GPU itself (rather
than the root port) is capable of runtime suspending to D3cold. If the
GPU's integrated HDA controller is not bound and the GPU's driver
decides to runtime suspend to D3cold, the HDA controller's BARs will be
uninitialized when a driver later probes it.
Fix by saving and restoring config space over a runtime suspend cycle
even if the device is not bound.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[lukas: add commit message, bikeshed code comments for clarity]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/92fb6e6ae2730915eb733c08e2f76c6a313e3860.1520068884.git.lukas@wunner.de
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 831c326fcd ]
Commit ad67b74d24 ("printk: hash addresses printed with %p") lets
printk specifier %p to hash all addresses before printing, this was
resulting in the high 32 bits of pcsr can only output zeros. So
module cannot completely print pc value and it's pointless for debugging
purpose.
This patch fixes this by using %px to print pcsr instead.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 563c4ba3bd ]
ah_attr contains the port number to which cm_id is bound. However, while
searching for GID table for matching GID entry, the port number is
ignored.
This could cause the wrong GID to be used when the ah_attr is converted to
an AH.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fca32340a5 ]
Executing command 'perf stat -T -- ls' dumps core on x86 and s390.
Here is the call back chain (done on x86):
# gdb ./perf
....
(gdb) r stat -T -- ls
...
Program received signal SIGSEGV, Segmentation fault.
0x00007ffff56d1963 in vasprintf () from /lib64/libc.so.6
(gdb) where
#0 0x00007ffff56d1963 in vasprintf () from /lib64/libc.so.6
#1 0x00007ffff56ae484 in asprintf () from /lib64/libc.so.6
#2 0x00000000004f1982 in __parse_events_add_pmu (parse_state=0x7fffffffd580,
list=0xbfb970, name=0xbf3ef0 "cpu",
head_config=0xbfb930, auto_merge_stats=false) at util/parse-events.c:1233
#3 0x00000000004f1c8e in parse_events_add_pmu (parse_state=0x7fffffffd580,
list=0xbfb970, name=0xbf3ef0 "cpu",
head_config=0xbfb930) at util/parse-events.c:1288
#4 0x0000000000537ce3 in parse_events_parse (_parse_state=0x7fffffffd580,
scanner=0xbf4210) at util/parse-events.y:234
#5 0x00000000004f2c7a in parse_events__scanner (str=0x6b66c0
"task-clock,{instructions,cycles,cpu/cycles-t/,cpu/tx-start/}",
parse_state=0x7fffffffd580, start_token=258) at util/parse-events.c:1673
#6 0x00000000004f2e23 in parse_events (evlist=0xbe9990, str=0x6b66c0
"task-clock,{instructions,cycles,cpu/cycles-t/,cpu/tx-start/}", err=0x0)
at util/parse-events.c:1713
#7 0x000000000044e137 in add_default_attributes () at builtin-stat.c:2281
#8 0x000000000044f7b5 in cmd_stat (argc=1, argv=0x7fffffffe3b0) at
builtin-stat.c:2828
#9 0x00000000004c8b0f in run_builtin (p=0xab01a0 <commands+288>, argc=4,
argv=0x7fffffffe3b0) at perf.c:297
#10 0x00000000004c8d7c in handle_internal_command (argc=4,
argv=0x7fffffffe3b0) at perf.c:349
#11 0x00000000004c8ece in run_argv (argcp=0x7fffffffe20c,
argv=0x7fffffffe200) at perf.c:393
#12 0x00000000004c929c in main (argc=4, argv=0x7fffffffe3b0) at perf.c:537
(gdb)
It turns out that a NULL pointer is referenced. Here are the
function calls:
...
cmd_stat()
+---> add_default_attributes()
+---> parse_events(evsel_list, transaction_attrs, NULL);
3rd parameter set to NULL
Function parse_events(xx, xx, struct parse_events_error *err) dives
into a bison generated scanner and creates
parser state information for it first:
struct parse_events_state parse_state = {
.list = LIST_HEAD_INIT(parse_state.list),
.idx = evlist->nr_entries,
.error = err, <--- NULL POINTER !!!
.evlist = evlist,
};
Now various functions inside the bison scanner are called to end up in
__parse_events_add_pmu(struct parse_events_state *parse_state, ..) with
first parameter being a pointer to above structure definition.
Now the PMU event name is not found (because being executed in a VM) and
this function tries to create an error message with
asprintf(&parse_state->error.str, ....)
which references a NULL pointer and dumps core.
Fix this by providing a pointer to the necessary error information
instead of NULL. Technically only the else part is needed to avoid the
core dump, just lets be safe...
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180308145735.64717-1-tmricht@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
