commit fbaa38214c upstream.
The CDAT exposed in sysfs differs between little endian and big endian
arches: On big endian, every 4 bytes are byte-swapped.
PCI Configuration Space is little endian (PCI r3.0 sec 6.1). Accessors
such as pci_read_config_dword() implicitly swap bytes on big endian.
That way, the macros in include/uapi/linux/pci_regs.h work regardless of
the arch's endianness. For an example of implicit byte-swapping, see
ppc4xx_pciex_read_config(), which calls in_le32(), which uses lwbrx
(Load Word Byte-Reverse Indexed).
DOE Read/Write Data Mailbox Registers are unlike other registers in
Configuration Space in that they contain or receive a 4 byte portion of
an opaque byte stream (a "Data Object" per PCIe r6.0 sec 7.9.24.5f).
They need to be copied to or from the request/response buffer verbatim.
So amend pci_doe_send_req() and pci_doe_recv_resp() to undo the implicit
byte-swapping.
The CXL_DOE_TABLE_ACCESS_* and PCI_DOE_DATA_OBJECT_DISC_* macros assume
implicit byte-swapping. Byte-swap requests after constructing them with
those macros and byte-swap responses before parsing them.
Change the request and response type to __le32 to avoid sparse warnings.
Per a request from Jonathan, replace sizeof(u32) with sizeof(__le32) for
consistency.
Fixes: c97006046c ("cxl/port: Read CDAT table")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org # v6.0+
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/3051114102f41d19df3debbee123129118fc5e6d.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 32d8599968 ]
Dan reports that smatch complains about a potential uninitialized
variable being used in the compat alignment fixup code.
The logic is not wrong per se, but we do end up using an uninitialized
variable if reading the instruction that triggered the alignment fault
from user space faults, even if the fault ensures that the uninitialized
value doesn't propagate any further.
Given that we just give up and return 1 if any fault occurs when reading
the instruction, let's get rid of the 'success handling' pattern that
captures the fault in a variable and aborts later, and instead, just
return 1 immediately if any of the get_user() calls result in an
exception.
Fixes: 3fc24ef32d ("arm64: compat: Implement misalignment fixups for multiword loads")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202304021214.gekJ8yRc-lkp@intel.com/
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20230404103625.2386382-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ce9345580 ]
Non-GSO TCP packets whose SKBs' linear portion did not include the
entire TCP header were not populating the first Tx descriptor with
as many bytes as the vNIC expected. This change ensures that all
TCP packets populate the first descriptor with the correct number of
bytes.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Shailend Chand <shailend@google.com>
Link: https://lore.kernel.org/r/20230403172809.2939306-1-shailend@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e847c7675e ]
If the number of lanes was forced and then subsequently the user
omits this parameter, the ksettings->lanes is reset. The driver
should then reset the number of lanes to the device's default
for the specified speed.
However, although the ksettings->lanes is set to 0, the mod variable
is not set to true to indicate the driver and userspace should be
notified of the changes.
The consequence is that the same ethtool operation will produce
different results based on the initial state.
If the initial state is:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 2
Duplex: Full
Auto-negotiation: on
then executing 'ethtool -s swp1 speed 50000 autoneg off' will yield:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 2
Duplex: Full
Auto-negotiation: off
While if the initial state is:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 1
Duplex: Full
Auto-negotiation: off
executing the same 'ethtool -s swp1 speed 50000 autoneg off' results in:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 1
Duplex: Full
Auto-negotiation: off
This patch fixes this behavior. Omitting lanes will always results in
the driver choosing the default lane width for the chosen speed. In this
scenario, regardless of the initial state, the end state will be, e.g.,
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 2
Duplex: Full
Auto-negotiation: off
Fixes: 012ce4dd31 ("ethtool: Extend link modes settings uAPI with lanes")
Signed-off-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/ac238d6b-8726-8156-3810-6471291dbc7f@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab5fb73ffa ]
After commit dbca1596bb ("ping: convert to RCU lookups, get rid
of rwlock"), we use RCU for ping sockets, but we should use spinlock
for /proc/net/icmp to avoid a potential NULL deref mentioned in
the previous patch.
Let's go back to using spinlock there.
Note we can convert ping sockets to use hlist instead of hlist_nulls
because we do not use SLAB_TYPESAFE_BY_RCU for ping sockets.
Fixes: dbca1596bb ("ping: convert to RCU lookups, get rid of rwlock")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6579f5bacc ]
Some applications seem to rely on RAW sockets.
If they use private netns, we can avoid piling all RAW
sockets bound to a given protocol into a single bucket.
Also place (struct raw_hashinfo).lock into its own
cache line to limit false sharing.
Alternative would be to have per-netns hashtables,
but this seems too expensive for most netns
where RAW sockets are not used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 0a78cf7264 ("raw: Fix NULL deref in raw_get_next().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83c911dc5e ]
Reset the FDIR counters when FDIR inits. Without this patch,
when VF initializes or resets, all the FDIR counters are not
cleaned, which may cause unexpected behaviors for future FDIR
rule create (e.g., rule conflict).
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Lingyu Liu <lingyu.liu@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4a01ace20 ]
When adding a FDIR filter, if ice_vc_fdir_set_irq_ctx returns failure,
the inserted fdir entry will not be removed and if ice_vc_fdir_write_fltr
returns failure, the fdir context info for irq handler will not be cleared
which may lead to inconsistent or memory leak issue. This patch refines
failure cases to resolve this issue.
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Simei Su <simei.su@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de82c2f36 ]
Currently callback request does not use the credential specified in
CREATE_SESSION if the security flavor for the back channel is AUTH_SYS.
Problem was discovered by pynfs 4.1 DELEG5 and DELEG7 test with error:
DELEG5 st_delegation.testCBSecParms : FAILURE
expected callback with uid, gid == 17, 19, got 0, 0
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Fixes: 8276c902bb ("SUNRPC: remove uid and gid from struct auth_cred")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6b486fb33 ]
In the am65_cpsw_nuss_probe() function's cleanup path, the call to
of_platform_device_destroy() for the common->mdio_dev device is invoked
unconditionally. It is possible that either the MDIO node is not present
in the device-tree, or the MDIO node is disabled in the device-tree. In
both these cases, the MDIO device is not created, resulting in a NULL
pointer dereference when the of_platform_device_destroy() function is
invoked on the common->mdio_dev device on the cleanup path.
Fix this by ensuring that the common->mdio_dev device exists, before
attempting to invoke of_platform_device_destroy().
Fixes: a45cfcc69a ("net: ethernet: ti: am65-cpsw-nuss: use of_platform_device_create() for mdio")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230403090321.835877-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe092498cb ]
The interrupt enable bits might be set if we want to use the GPIO as
wakeup source. Clearing this will mean disabling of interrupts in the GPIO
banks that we may want to wakeup from.
Thus remove the line that was clearing this bit from the driver's save
context function.
Cc: Devarsh Thakkar <devarsht@ti.com>
Fixes: 0651a73092 ("gpio: davinci: Add support for system suspend/resume PM")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 839349d139 ]
On the remote side, when QRTR socket is removed, af_qrtr will call
qrtr_port_remove() which broadcasts the DEL_CLIENT packet to all neighbours
including local NS. NS upon receiving the DEL_CLIENT packet, will remove
the lookups associated with the node:port and broadcasts the DEL_SERVER
packet.
But on the host side, due to the arrival of the DEL_CLIENT packet, the NS
would've already deleted the server belonging to that port. So when the
remote's NS again broadcasts the DEL_SERVER for that port, it throws below
error message on the host:
"failed while handling packet from 2:-2"
So fix this error by not broadcasting the DEL_SERVER packet when the
DEL_CLIENT packet gets processed."
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ram Kumar Dharuman <quic_ramd@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2584024b23 ]
This patch fixes a corner case where the asoc out stream count may change
after wait_for_sndbuf.
When the main thread in the client starts a connection, if its out stream
count is set to N while the in stream count in the server is set to N - 2,
another thread in the client keeps sending the msgs with stream number
N - 1, and waits for sndbuf before processing INIT_ACK.
However, after processing INIT_ACK, the out stream count in the client is
shrunk to N - 2, the same to the in stream count in the server. The crash
occurs when the thread waiting for sndbuf is awake and sends the msg in a
non-existing stream(N - 1), the call trace is as below:
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
Call Trace:
<TASK>
sctp_cmd_send_msg net/sctp/sm_sideeffect.c:1114 [inline]
sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1777 [inline]
sctp_side_effects net/sctp/sm_sideeffect.c:1199 [inline]
sctp_do_sm+0x197d/0x5310 net/sctp/sm_sideeffect.c:1170
sctp_primitive_SEND+0x9f/0xc0 net/sctp/primitive.c:163
sctp_sendmsg_to_asoc+0x10eb/0x1a30 net/sctp/socket.c:1868
sctp_sendmsg+0x8d4/0x1d90 net/sctp/socket.c:2026
inet_sendmsg+0x9d/0xe0 net/ipv4/af_inet.c:825
sock_sendmsg_nosec net/socket.c:722 [inline]
sock_sendmsg+0xde/0x190 net/socket.c:745
The fix is to add an unlikely check for the send stream number after the
thread wakes up from the wait_for_sndbuf.
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+47c24ca20a2fa01f082e@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 089b91a015 ]
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 275b471e3d ]
Commit 0db3dc73f7 ("[NETPOLL]: tx lock deadlock fix") narrowed
down the region under netif_tx_trylock() inside netpoll_send_skb().
(At that point in time netif_tx_trylock() would lock all queues of
the device.) Taking the tx lock was problematic because driver's
cleanup method may take the same lock. So the change made us hold
the xmit lock only around xmit, and expected the driver to take
care of locking within ->ndo_poll_controller().
Unfortunately this only works if netpoll isn't itself called with
the xmit lock already held. Netpoll code is careful and uses
trylock(). The drivers, however, may be using plain lock().
Printing while holding the xmit lock is going to result in rare
deadlocks.
Luckily we record the xmit lock owners, so we can scan all the queues,
the same way we scan NAPI owners. If any of the xmit locks is held
by the local CPU we better not attempt any polling.
It would be nice if we could narrow down the check to only the NAPIs
and the queue we're trying to use. I don't see a way to do that now.
Reported-by: Roman Gushchin <roman.gushchin@linux.dev>
Fixes: 0db3dc73f7 ("[NETPOLL]: tx lock deadlock fix")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f785f5ee96 ]
When a DRM driver turns on or off the screen with the audio
capability, it notifies the ELD to HD-audio HDMI codec driver via
component ops. HDMI codec driver, in turn, attaches or detaches the
PCM stream for the given port on the fly.
The problem is that, since the recent code change, the HDMI driver
always treats the PCM stream assignment dynamically; this ended up the
confusion of the PCM device appearance. e.g. when a screen goes once
off and on again, it may appear on a different PCM device before the
screen-off. Although the application should treat such a change, it
doesn't seem working gracefully with the current pipewire (maybe
PulseAudio, too).
As a workaround, this patch changes the HDMI codec driver behavior
slightly to be more consistent. Now it remembers the previous PCM
slot for the given port and try to assign to it. That is, if a port
is re-enabled, the driver tries to use the same PCM slot that was
assigned to that port previously. If it conflicts, a new slot is
searched and used like before, instead.
Note that multiple monitor connections are the only typical case where
the PCM slot preservation is effective. As long as only a single
monitor is connected, the behavior isn't changed, and the first PCM
slot is still assigned always.
Fixes: ef6f5494fa ("ALSA: hda/hdmi: Use only dynamic PCM device allocation")
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217259
Link: https://lore.kernel.org/r/20230331142217.19791-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a8b55dbb ]
For ops with "trivial" replies, nfsd4_encode_operation will shortcut
most of the encoding work and skip to just marshalling up the status.
One of the things it skips is calling op_release. This could cause a
memory leak in the layoutget codepath if there is an error at an
inopportune time.
Have the compound processing engine always call op_release, even when
op_func sets an error in op->status. With this change, we also need
nfsd4_block_get_device_info_scsi to set the gd_device pointer to NULL
on error to avoid a double free.
Reported-by: Zhi Li <yieli@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2181403
Fixes: 34b1744c91 ("nfsd4: define ->op_release for compound ops")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 804d8e0a6e ]
OPDESC() simply indexes into nfsd4_ops[] by the op's operation
number, without range checking that value. It assumes callers are
careful to avoid calling it with an out-of-bounds opnum value.
nfsd4_decode_compound() is not so careful, and can invoke OPDESC()
with opnum set to OP_ILLEGAL, which is 10044 -- well beyond the end
of nfsd4_ops[].
Reported-by: Jeff Layton <jlayton@kernel.org>
Fixes: f4f9ef4a1b ("nfsd4: opdesc will be useful outside nfs4proc.c")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4efa515d5 ]
After commit 92cadedd9d ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on suspend
and then re-probed on resume.
In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
the newly added re-probe on resume fails like this:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
It seems this specific brcmfmac model does not like being reprobed without
it actually being turned off first.
And the adapter is not being turned off during suspend because of
commit f0992ace68 ("brcmfmac: prohibit ACPI power management for brcmfmac
driver").
Now that the driver is being reprobed on resume, the disabling of ACPI
pm is no longer necessary, except when WOWL is used (in which case there
is no-reprobe).
Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
the brcmfmac43430a1 suspend/resume regression and should help save some
power when suspended.
This change means that the code now also may re-enable ACPI pm when WOWL
gets disabled. ACPI pm should only be re-enabled if it was enabled by
the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
to save the original state for this.
This has been tested on the following devices:
Asus T100TA brcmfmac43241b4-sdio
Acer Iconia One 7 B1-750 brcmfmac43340-sdio
Chuwi Hi8 brcmfmac43430a0-sdio
Chuwi Hi8 brcmfmac43430a1-sdio
(the Asus T100TA is the device for which the prohibiting of ACPI pm
was originally added)
Fixes: 92cadedd9d ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320122252.240070-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 154e07c164 ]
Commit 65b32f801b ("uapi: move IPPROTO_L2TP to in.h") moved the
definition of IPPROTO_L2TP from a define to an enum, but since
__stringify doesn't work properly with enums, we ended up breaking the
modalias strings for the l2tp modules:
$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias: net-pf-2-proto-IPPROTO_L2TP
alias: net-pf-2-proto-2-type-IPPROTO_L2TP
alias: net-pf-10-proto-IPPROTO_L2TP
alias: net-pf-10-proto-2-type-IPPROTO_L2TP
Use the resolved number directly in MODULE_ALIAS_*() macros (as we
already do with SOCK_DGRAM) to fix the alias strings:
$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias: net-pf-2-proto-115
alias: net-pf-2-proto-115-type-2
alias: net-pf-10-proto-115
alias: net-pf-10-proto-115-type-2
Moreover, fix the ordering of the parameters passed to
MODULE_ALIAS_NET_PF_PROTO_TYPE() by switching proto and type.
Fixes: 65b32f801b ("uapi: move IPPROTO_L2TP to in.h")
Link: https://lore.kernel.org/lkml/ZCQt7hmodtUaBlCP@righiandr-XPS-13-7390
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc21a6ed5 ]
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d ("stmmac: intel: prepare to support 1000BASE-X phy interface setting")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2cfbc968 ]
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf9209 ("net: stmmac: make mdio register skips PHY scanning for fixed-link")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 653a180957 ]
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fe2cfbc968 ("net: stmmac: check if MAC needs to attach to a PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f27df854 ]
To determine whether the guest has caused an external interruption loop
upon code 20 (external interrupt) intercepts, the ext_new_psw needs to
be inspected to see whether external interrupts are enabled.
Under non-PV, ext_new_psw can simply be taken from guest lowcore. Under
PV, KVM can only access the encrypted guest lowcore and hence the
ext_new_psw must not be taken from guest lowcore.
handle_external_interrupt() incorrectly did that and hence was not able
to reliably tell whether an external interruption loop is happening or
not. False negatives cause spurious failures of my kvm-unit-test
for extint loops[1] under PV.
Since code 20 is only caused under PV if and only if the guest's
ext_new_psw is enabled for external interrupts, false positive detection
of a external interruption loop can not happen.
Fix this issue by instead looking at the guest PSW in the state
description. Since the PSW swap for external interrupt is done by the
ultravisor before the intercept is caused, this reliably tells whether
the guest is enabled for external interrupts in the ext_new_psw.
Also update the comments to explain better what is happening.
[1] https://lore.kernel.org/kvm/20220812062151.1980937-4-nrb@linux.ibm.com/
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Fixes: 201ae986ea ("KVM: s390: protvirt: Implement interrupt injection")
Link: https://lore.kernel.org/r/20230213085520.100756-2-nrb@linux.ibm.com
Message-Id: <20230213085520.100756-2-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4a3203426 ]
The order in which clocks are stopped matters as some of the clock
like NPL are derived from MCLK.
Without this patch, Dragonboard RB5 DSP would crash with below error:
qcom_q6v5_pas 17300000.remoteproc: fatal error received:
ABT_dal.c:278:ABTimeout: AHB Bus hang is detected,
Number of bus hang detected := 2 , addr0 = 0x3370000 , addr1 = 0x0!!!
Turn off fsgen first, followed by npl and then finally mclk, which is exactly
the opposite order of enable sequence.
Fixes: 1dc3459009 ("ASoC: codecs: lpass: register mclk after runtime pm")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20230323110125.23790-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8caa81eb95 ]
The driver only supports normal polarity. Complete the implementation of
.get_state() by setting .polarity accordingly.
This fixes a regression that was possible since commit c73a310762
("pwm: Handle .get_state() failures") which stopped to zero-initialize
the state passed to the .get_state() callback. This was reported at
https://forum.odroid.com/viewtopic.php?f=177&t=46360 . While this was an
unintended side effect, the real issue is the driver's callback not
setting the polarity.
There is a complicating fact, that the .apply() callback fakes support
for inversed polarity. This is not (and cannot) be matched by
.get_state(). As fixing this isn't easy, only point it out in a comment
to prevent authors of other drivers from copying that approach.
Fixes: c375bcbaab ("pwm: meson: Read the full hardware state in meson_pwm_get_state()")
Reported-by: Munehisa Kamata <kamatam@amazon.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230310191405.2606296-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c452cff79 ]
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 6f57937980 ("pwm: hibvt: Explicitly set .polarity in .get_state()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eb65c8687 ]
relid2channel() assumes vmbus channel array to be allocated when called.
However, in cases such as kdump/kexec, not all relids will be reset by the host.
When the second kernel boots and if the guest receives a vmbus interrupt during
vmbus driver initialization before vmbus_connect() is called, before it finishes,
or if it fails, the vmbus interrupt service routine is called which in turn calls
relid2channel() and can cause a null pointer dereference.
Print a warning and error out in relid2channel() for a channel id that's invalid
in the second kernel.
Fixes: 8b6a877c06 ("Drivers: hv: vmbus: Replace the per-CPU channel lists with a global array of channels")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20230217204411.212709-1-mgamal@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49765b5f4 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ebe363197e ("gpio: add a reusable generic gpio_chip using regmap")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Walle <michael@walle.cc>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: linux-gpio@vger.kernel.org
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6da81f650 ]
Presently, when a guest writes 1 to PMCR_EL0.{C,P}, which is WO/RAZ,
KVM saves the register value, including these bits.
When userspace reads the register using KVM_GET_ONE_REG, KVM returns
the saved register value as it is (the saved value might have these
bits set). This could result in userspace setting these bits on the
destination during migration. Consequently, KVM may end up resetting
the vPMU counter registers (PMCCNTR_EL0 and/or PMEVCNTR<n>_EL0) to
zero on the first KVM_RUN after migration.
Fix this by not saving those bits when a guest writes 1 to those bits.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230313033234.1475987-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
