Badhri Jagan Sridharan b248dd37db FROMGIT: usb: typec: tcpm: Honour pSnkStdby requirement during negotiation
>From PD Spec:
The Sink Shall transition to Sink Standby before a positive or
negative voltage transition of VBUS. During Sink Standby
the Sink Shall reduce its power draw to pSnkStdby. This allows
the Source to manage the voltage transition as well as
supply sufficient operating current to the Sink to maintain PD
operation during the transition. The Sink Shall
complete this transition to Sink Standby within tSnkStdby
after evaluating the Accept Message from the Source. The
transition when returning to Sink operation from Sink Standby
Shall be completed within tSnkNewPower. The
pSnkStdby requirement Shall only apply if the Sink power draw
is higher than this level.

The above requirement needs to be met to prevent hard resets
from port partner.

Without the patch: (5V/3A during SNK_DISCOVERY all the way through
explicit contract)
[   95.711984] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[   95.712007] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[   95.712017] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[   95.837190] VBUS on
[   95.882075] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[   95.882082] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[   95.882086] polarity 1
[   95.883151] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[   95.883441] enable vbus discharge ret:0
[   95.883445] Requesting mux state 1, usb-role 2, orientation 2
[   95.883776] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[   95.883879] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[   96.038960] VBUS on
[   96.383939] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[   96.383946] Setting voltage/current limit 5000 mV 3000 mA
[   96.383961] vbus=0 charge:=1
[   96.386044] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[   96.386309] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[   96.394404] PD RX, header: 0x2161 [1]
[   96.394408]  PDO 0: type 0, 5000 mV, 3000 mA [E]
[   96.394410]  PDO 1: type 0, 9000 mV, 2000 mA []
[   96.394412] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[   96.394416] Setting usb_comm capable false
[   96.395083] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[   96.395089] Requesting PDO 1: 9000 mV, 2000 mA
[   96.395093] PD TX, header: 0x1042
[   96.397404] PD TX complete, status: 0
[   96.397424] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[   96.400826] PD RX, header: 0x363 [1]
[   96.400829] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[   96.400832] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[   96.577315] PD RX, header: 0x566 [1]
[   96.577321] Setting voltage/current limit 9000 mV 2000 mA
[   96.578363] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[   96.578370] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]

With the patch:
[  168.398573] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[  168.398605] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[  168.398619] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[  168.522348] VBUS on
[  168.568676] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[  168.568684] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[  168.568688] polarity 1
[  168.569867] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[  168.570158] enable vbus discharge ret:0
[  168.570161] Requesting mux state 1, usb-role 2, orientation 2
[  168.570504] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[  168.570634] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[  169.070689] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[  169.070695] Setting voltage/current limit 5000 mV 3000 mA
[  169.070702] vbus=0 charge:=1
[  169.072719] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[  169.073145] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[  169.077162] PD RX, header: 0x2161 [1]
[  169.077172]  PDO 0: type 0, 5000 mV, 3000 mA [E]
[  169.077178]  PDO 1: type 0, 9000 mV, 2000 mA []
[  169.077183] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[  169.077191] Setting usb_comm capable false
[  169.077753] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[  169.077759] Requesting PDO 1: 9000 mV, 2000 mA
[  169.077762] PD TX, header: 0x1042
[  169.079990] PD TX complete, status: 0
[  169.080013] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[  169.083183] VBUS on
[  169.084195] PD RX, header: 0x363 [1]
[  169.084200] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[  169.084206] Setting standby current 5000 mV @ 500 mA
[  169.084209] Setting voltage/current limit 5000 mV 500 mA
[  169.084220] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[  169.260222] PD RX, header: 0x566 [1]
[  169.260227] Setting voltage/current limit 9000 mV 2000 mA
[  169.261315] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[  169.261321] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
[  169.261570] AMS POWER_NEGOTIATION finished

Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 1230868433
 https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-next)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I54edfc601d28c8b67b4cdb7b8cb313dbd239021a
2021-04-15 06:43:10 +00:00
2021-04-13 23:28:09 +00:00
2021-04-11 09:11:53 +02:00
2021-04-11 09:11:53 +02:00
2021-04-11 09:11:53 +02:00
2021-04-11 09:11:53 +02:00
2021-04-02 15:25:50 +02:00
2021-04-11 09:11:53 +02:00
2021-04-11 09:11:53 +02:00

How do I submit patches to Android Common Kernels

  1. BEST: Make all of your changes to upstream Linux. If appropriate, backport to the stable releases. These patches will be merged automatically in the corresponding common kernels. If the patch is already in upstream Linux, post a backport of the patch that conforms to the patch requirements below.

    • Do not send patches upstream that contain only symbol exports. To be considered for upstream Linux, additions of EXPORT_SYMBOL_GPL() require an in-tree modular driver that uses the symbol -- so include the new driver or changes to an existing driver in the same patchset as the export.
    • When sending patches upstream, the commit message must contain a clear case for why the patch is needed and beneficial to the community. Enabling out-of-tree drivers or functionality is not not a persuasive case.
  2. LESS GOOD: Develop your patches out-of-tree (from an upstream Linux point-of-view). Unless these are fixing an Android-specific bug, these are very unlikely to be accepted unless they have been coordinated with kernel-team@android.com. If you want to proceed, post a patch that conforms to the patch requirements below.

Common Kernel patch requirements

  • All patches must conform to the Linux kernel coding standards and pass script/checkpatch.pl
  • Patches shall not break gki_defconfig or allmodconfig builds for arm, arm64, x86, x86_64 architectures (see https://source.android.com/setup/build/building-kernels)
  • If the patch is not merged from an upstream branch, the subject must be tagged with the type of patch: UPSTREAM:, BACKPORT:, FROMGIT:, FROMLIST:, or ANDROID:.
  • All patches must have a Change-Id: tag (see https://gerrit-review.googlesource.com/Documentation/user-changeid.html)
  • If an Android bug has been assigned, there must be a Bug: tag.
  • All patches must have a Signed-off-by: tag by the author and the submitter

Additional requirements are listed below based on patch type

Requirements for backports from mainline Linux: UPSTREAM:, BACKPORT:

  • If the patch is a cherry-pick from Linux mainline with no changes at all
    • tag the patch subject with UPSTREAM:.
    • add upstream commit information with a (cherry picked from commit ...) line
    • Example:
      • if the upstream commit message is
        important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>
  • then Joe Smith would upload the patch for the common kernel as
        UPSTREAM: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        (cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
        Signed-off-by: Joe Smith <joe.smith@foo.org>
  • If the patch requires any changes from the upstream version, tag the patch with BACKPORT: instead of UPSTREAM:.
    • use the same tags as UPSTREAM:
    • add comments about the changes under the (cherry picked from commit ...) line
    • Example:
        BACKPORT: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        (cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
        [joe: Resolved minor conflict in drivers/foo/bar.c ]
        Signed-off-by: Joe Smith <joe.smith@foo.org>

Requirements for other backports: FROMGIT:, FROMLIST:,

  • If the patch has been merged into an upstream maintainer tree, but has not yet been merged into Linux mainline
    • tag the patch subject with FROMGIT:
    • add info on where the patch came from as (cherry picked from commit <sha1> <repo> <branch>). This must be a stable maintainer branch (not rebased, so don't use linux-next for example).
    • if changes were required, use BACKPORT: FROMGIT:
    • Example:
      • if the commit message in the maintainer tree is
        important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>
  • then Joe Smith would upload the patch for the common kernel as
        FROMGIT: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        (cherry picked from commit 878a2fd9de10b03d11d2f622250285c7e63deace
         https://git.kernel.org/pub/scm/linux/kernel/git/foo/bar.git test-branch)
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        Signed-off-by: Joe Smith <joe.smith@foo.org>
  • If the patch has been submitted to LKML, but not accepted into any maintainer tree
    • tag the patch subject with FROMLIST:
    • add a Link: tag with a link to the submittal on lore.kernel.org
    • add a Bug: tag with the Android bug (required for patches not accepted into a maintainer tree)
    • if changes were required, use BACKPORT: FROMLIST:
    • Example:
        FROMLIST: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        Link: https://lore.kernel.org/lkml/20190619171517.GA17557@someone.com/
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        Signed-off-by: Joe Smith <joe.smith@foo.org>

Requirements for Android-specific patches: ANDROID:

  • If the patch is fixing a bug to Android-specific code
    • tag the patch subject with ANDROID:
    • add a Fixes: tag that cites the patch with the bug
    • Example:
        ANDROID: fix android-specific bug in foobar.c

        This is the detailed description of the important fix

        Fixes: 1234abcd2468 ("foobar: add cool feature")
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        Signed-off-by: Joe Smith <joe.smith@foo.org>
  • If the patch is a new feature
    • tag the patch subject with ANDROID:
    • add a Bug: tag with the Android bug (required for android-specific features)
Description
No description provided
Readme 7.9 GiB
Languages
C 97.7%
Assembly 1.6%
Makefile 0.3%
Perl 0.1%