[ Upstream commit 19c234a14e ]
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A
If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A
Fixes: 74e656d6b0 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3db1d52466 ]
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-13-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f77d19207 ]
Transmission complete error is sent when ISR_TC is not set. If port closure
is requested despite data in TDR / TX FIFO has not been sent (because of
flow control), ISR_TC is not set and error message is sent on port closure
but also when a new port is opened.
Flush the data when port is closed, so the error isn't printed twice upon
next port opening.
Fixes: 64c32eab66 ("serial: stm32: Add support of TC bit status check")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-12-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 436c979360 ]
CTS/RTS GPIOs support that has been added recently to STM32 UART driver has
introduced scheduled code in a set_termios part protected by a spin lock.
This generates a potential deadlock scenario:
Chain exists of:
&irq_desc_lock_class --> console_owner --> &port_lock_key
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&port_lock_key);
lock(console_owner);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
4 locks held by stty/766:
Move the scheduled code after the spinlock.
Fixes: 6cf61b9bd7 ("tty: serial: Add modem control gpio support for STM32 UART")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-8-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12761869f0 ]
This patch fixes several issue with wake-up handling:
- the WUF irq is handled several times at wake-up
- the USART is disabled / enabled at suspend to set wake-up flag.
It can cause glitches during RX.
This patch fix those issues:
- clear wake-up flag and disable wake-up irq in WUF irq handling
- enable wake-up from low power on start bit detection at port
configuration
- Unmask the wake-up flag irq at suspend and mask it at resume
In addition, pm_wakeup_event handling is moved from receice_chars to WUF
irq handling.
Fixes: 270e5a74fe ("serial: stm32: add wakeup mechanism")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-7-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad76768124 ]
Deadlock issue is seen when enabling CONFIG_PROVE_LOCKING=Y, and uart
console as wakeup source. Deadlock occurs when resuming from low power
mode if system is waked up via usart console.
The deadlock is triggered 100% when also disabling console suspend prior
to go to suspend.
Simplified call stack, deadlock condition:
- stm32_console_write <-- spin_lock already held
- print_circular_bug
- pm_wakeup_dev_event <-- triggers lockdep as seen above
- stm32_receive_chars
- stm32_interrupt <-- wakeup via uart console, takes the lock
So, revisit spin_lock in stm32-usart driver:
- there is no need to hold the lock to access ICR (atomic clear of status
flags)
- only hold the lock inside stm32_receive_chars() routine (no need to
call pm_wakeup_dev_event with lock held)
- keep stm32_transmit_chars() routine called with lock held
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-6-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25a8e7611d ]
TX and RX FIFO thresholds may be cleared after suspend/resume, depending
on the low power mode.
Those configurations (done in startup) are not effective for UART console,
as:
- the reference manual indicates that FIFOEN bit can only be written when
the USART is disabled (UE=0)
- a set_termios (where UE is set) is requested firstly for console
enabling, before the startup.
Fixes: 84872dc448 ("serial: stm32: add RX and TX FIFO flush")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-5-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f264c6f6ae ]
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87fd0741d6 ]
The probe and remove orders are wrong as the uart_port is registered
before saving device data in the probe, and unregistered after DMA
resource deallocation in the remove. uart_port registering should be
done at the end of probe and unregistering should be done at the begin of
remove to avoid resource allocation issues.
Fix probe and remove orders. This enforce resource allocation occur at
proper time.
Terminate both DMA rx and tx transfers before removing device.
Move pm_runtime after uart_remove_one_port() call in remove() to keep the
probe error path.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6840a150b9 ]
Commit
bbbd2b51a2 ("x86/platform/UV: Use new set memory block size function")
added a call to set the block size value that is needed by the kernel
to set the boundaries in the section list. This was done for UV Hubbed
systems but missed in the UV Hubless setup. Fix that mistake by adding
that same set call for hubless systems, which support the same NVRAMs
and Intel BIOS, thus the same problem occurs.
[ bp: Massage commit message. ]
Fixes: bbbd2b51a2 ("x86/platform/UV: Use new set memory block size function")
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Russ Anderson <rja@hpe.com>
Link: https://lkml.kernel.org/r/20210305162853.299892-1-mike.travis@hpe.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8987efbb17 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: c61248afa8 ("ARM: dts: Add max77686 RTC interrupt to cros5250-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6368c6056 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6503c568e9 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: eea6653aae ("ARM: dts: Enable PMIC interrupts for exynos4412-odroid-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e52dcd6e70 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 15dfdfad2d ("ARM: dts: Add basic dts for Exynos4412-based Trats 2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15107e443a ]
The Maxim MUIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 7eec126675 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a45f33bd3 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: e8614292cd ("ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4679980213 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e004c3e67b ]
Currently the array gpmc_cs is indexed by cs before it cs is range checked
and the pointer read from this out-of-index read is dereferenced. Fix this
by performing the range check on cs before the read and the following
pointer dereference.
Addresses-Coverity: ("Negative array index read")
Fixes: 9ed7a776eb ("ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210223193821.17232-1-colin.king@canonical.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484a58607a ]
The current code produces an error message on devm_gpiod_get() errors even
when the error is -EPROBE_DEFER, which should be silent.
This has been observed producing a significant amount of messages like:
xlnx-slave-spi spi1.1: Failed to get PROGRAM_B gpio: -517
Fix and simplify code by using the dev_err_probe() helper function.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Fixes: dd2784c01d ("fpga manager: xilinx-spi: check INIT_B pin during write_init")
Fixes: 061c97d13f ("fpga manager: Add Xilinx slave serial SPI driver")
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79bfe480a0 ]
zynqmp_pm_get_eemi_ops() was removed in commit 4db8180ffe: "Firmware: xilinx:
Remove eemi ops for fpga related APIs", but not in IS_REACHABLE(CONFIG_ZYNQMP_FIRMWARE).
Any driver who want to communicate with PMC using EEMI APIs use the functions provided
for each function
This removed zynqmp_pm_get_eemi_ops() in IS_REACHABLE(CONFIG_ZYNQMP_FIRMWARE), and also
modify the documentation for this driver.
Fixes: 4db8180ffe ("firmware: xilinx: Remove eemi ops for fpga related APIs")
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20210215155849.2425846-1-iwamatsu@nigauri.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2b94be787 upstream.
This reverts commit 6ff7cb371c.
Apparently the TCC offset should not be used to adjust what temperature
we show the user after all.
(on most systems, TCC offset is 0, FWIW)
Fixes: 6ff7cb371c
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50a318cc9b upstream.
The commit d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a121 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b279bbfd2 upstream.
Smatch complains about missing that the ovl_override_creds() doesn't
have a matching revert_creds() if the dentry is disconnected. Fix this
by moving the ovl_override_creds() until after the disconnected check.
Fixes: aa3ff3c152 ("ovl: copy up of disconnected dentries")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d362fd0be4 upstream.
This reverts commit 1b479fb801
("drivers/net/wan/hdlc_fr: Fix a double free in pvc_xmit").
1. This commit is incorrect. "__skb_pad" will NOT free the skb on
failure when its "free_on_error" parameter is "false".
2. This commit claims to fix my commit. But it didn't CC me??
Fixes: 1b479fb801 ("drivers/net/wan/hdlc_fr: Fix a double free in pvc_xmit")
Cc: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85d7037461 upstream.
On vcpu reset, we expect all the registers to be brought back
to their initial state, which happens to be a bunch of zeroes.
However, some recent commit broke this, and is now leaving a bunch
of registers (such as the FP state) with whatever was left by the
guest. My bad.
Zero the reset of the state (32bit SPSRs and FPSIMD state).
Cc: stable@vger.kernel.org
Fixes: e47c2055c6 ("KVM: arm64: Make struct kvm_regs userspace-only")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d3c4c7938 upstream.
Abort the walk of coalesced MMIO zones if kvm_io_bus_unregister_dev()
fails to allocate memory for the new instance of the bus. If it can't
instantiate a new bus, unregister_dev() destroys all devices _except_ the
target device. But, it doesn't tell the caller that it obliterated the
bus and invoked the destructor for all devices that were on the bus. In
the coalesced MMIO case, this can result in a deleted list entry
dereference due to attempting to continue iterating on coalesced_zones
after future entries (in the walk) have been deleted.
Opportunistically add curly braces to the for-loop, which encompasses
many lines but sneaks by without braces due to the guts being a single
if statement.
Fixes: f65886606c ("KVM: fix memory leak in kvm_io_bus_unregister_dev()")
Cc: stable@vger.kernel.org
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ee3757424 upstream.
If allocating a new instance of an I/O bus fails when unregistering a
device, wait to destroy the device until after all readers are guaranteed
to see the new null bus. Destroying devices before the bus is nullified
could lead to use-after-free since readers expect the devices on their
reference of the bus to remain valid.
Fixes: f65886606c ("KVM: fix memory leak in kvm_io_bus_unregister_dev()")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee050a5775 upstream.
Drop bits 63:32 of the VMCS field encoding when checking for a nested
VM-Exit on VMREAD/VMWRITE in !64-bit mode. VMREAD and VMWRITE always
use 32-bit operands outside of 64-bit mode.
The actual emulation of VMREAD/VMWRITE does the right thing, this bug is
purely limited to incorrectly causing a nested VM-Exit if a GPR happens
to have bits 63:32 set outside of 64-bit mode.
Fixes: a7cde481b6 ("KVM: nVMX: Do not forward VMREAD/VMWRITE VMExits to L1 if required so by vmcs12 vmread/vmwrite bitmaps")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422022128.3464144-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c805f5d558 upstream.
Defer reloading the MMU after a EPTP successful EPTP switch. The VMFUNC
instruction itself is executed in the previous EPTP context, any side
effects, e.g. updating RIP, should occur in the old context. Practically
speaking, this bug is benign as VMX doesn't touch the MMU when skipping
an emulated instruction, nor does queuing a single-step #DB. No other
post-switch side effects exist.
Fixes: 41ab937274 ("KVM: nVMX: Emulate EPTP switching for the L1 hypervisor")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210305011101.3597423-14-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8727906fde upstream.
Reject KVM_SEV_INIT and KVM_SEV_ES_INIT if they are attempted after one
or more vCPUs have been created. KVM assumes a VM is tagged SEV/SEV-ES
prior to vCPU creation, e.g. init_vmcb() needs to mark the VMCB as SEV
enabled, and svm_create_vcpu() needs to allocate the VMSA. At best,
creating vCPUs before SEV/SEV-ES init will lead to unexpected errors
and/or behavior, and at worst it will crash the host, e.g.
sev_launch_update_vmsa() will dereference a null svm->vmsa pointer.
Fixes: 1654efcbc4 ("KVM: SVM: Add KVM_SEV_INIT command")
Fixes: ad73109ae7 ("KVM: SVM: Provide support to launch and run an SEV-ES guest")
Cc: stable@vger.kernel.org
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210331031936.2495277-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
