on the situation that: charger is connected and fuel gauge gives
state 'CC or CV', but actually battery is discharging from 100%
to 99%. At this moment we may treat this as normal full charging
by mistake, so we must add current judgement to avoid that.
Change-Id: I7b6692c17dc053fd96bd42df05c3f7763728bba2
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
This patch reserved 14M memory zone for OPTEE side on rk3229-echo board.
Change-Id: I46de3f7163dc14361d41476daf44957184f43e89
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
[ 23.527279] rockchip-dp ff970000.edp: Timeout of video streamclk ok
[ 23.527325] rockchip-dp ff970000.edp: unable to config video
Change-Id: Ie2239c2dd773e4cb41f86b46b98367a07a751ff1
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
CTRLR1 is number of data frames.
When data frame is 8 bit, CTRLR1 is len-1.
When data frame is 16 bit, CTRLR1 is (len/2)-1.
Change-Id: I40b7ebd382f60bdfdab902394637c107d90531db
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
The greater leakage, the lower the OPP's voltage. In order to reduce
power consumption, it is necessary to adjust OPP's voltage according
to leakage.
Change-Id: I2bba04ac941cc6a0703b5208cb4e757ec2813bab
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
At same voltage and frequency, the greater the PVTM value, the lower
the OPP's voltage. In order to reduce power consumption, it is necessary
to adjust OPP's voltage according to PVTM value.
Change-Id: Ifcac57fc965e3ea45523db2d9df19435479f6cee
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
stress test:
1. Antutu, use governor simpleondemand
2. Need for Speed, use governor simpleondemand
3. Glmark2, use userspace, scanning frequency
Change-Id: Ibe27380e582b193d900b0d55da3567ce553c32df
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Pick out non-public dt nodes from dtsi and separately configure in dts.
Change-Id: I774f45e0b282fb1b783b5b175fa4ffc9ad904990
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Because Buck3 don't have sleep state register, so we need a manual
switch: set BUCK3 suspend as Auto PWM mode and resume as FPWM mode.
This is for power saving in system suspend.
Change-Id: I67db458e650b6e85ed4267f0b0dcdb01dff4c635
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
wifi driver open config such as below:
CONFIG_WOWLAN = y
CONFIG_GPIO_WAKEUP = y
Change-Id: I9bdb07e0210c68993bb638aa2ca403142e180c5f
Signed-off-by: Xu Xuehui <xxh@rock-chips.com>
Let us put phy-port into suspend mode at initialization time for
saving power consumption, and usb controller will resume it during
probe time if needed.
Change-Id: Id3a66af8ff17612d54fbc80db087bf67eaee7726
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
The full name of BCSH is Brightness, Contrast, Saturation and Hue.
BCSH is supported on all full vop designed.
Change-Id: I17bcd5a07b93b3c68aa892606f886bcd3a7673a0
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Some generic TV connector properties are exposed in drm_mode_config, but
they are currently handled independently in each DRM encoder driver.
Extend the drm_connector_state to store TV related states, and modify the
drm_atomic_connector_{set,get}_property() helpers to fill the connector
state accordingly.
Each driver is then responsible for checking and applying the new config
in its ->atomic_mode_{check,set}() operations.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 299a16b163)
Change-Id: I50d7c79013235d75972b8cdd46cf89bbd9cf596d
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
At same voltage and frequency, the greater the PVTM value, the lower
the OPP's voltage. In order to reduce power consumption, it is necessary
to adjust OPP's voltage according to PVTM value.
Change-Id: Ic1d2a74048f6c7d97d92868292f14776ea380d99
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
switch TX1/RX1 D-PHY of rk3288/3399 to RX status before it's
initialization to avoid conflicting with sensor output.
Change-Id: I672730fe5fb5a33b8437df1ae61078a9a79ac41b
Signed-off-by: zhangyunlong <dalon.zhang@rock-chips.com>
Enable the nand node by default in the android dtsi as
they're wired on every board for drmboot compatible.
Change-Id: I63aea9be6ca43fb91f7ec6616f5b9051ca5c23a8
Signed-off-by: Zhangbin Tong <zebulun.tong@rock-chips.com>
RK1000 is a digital-analog mixed chip which has tve output function.
RK1000's registers can be written and read through I2C interaface.
Because RK1000's I2C need dclk and mclk, RK1000 TVE should be registered
after RK1000 CORE. RBG signal output is controlled by LVDS, so RK1000
should be registered as connector and attach LVDS encoder.
Change-Id: I65b40826bd1dbf07d4fa94ecdf8c75005008731f
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
RK1000's control register block need mclk for i2c communication.
So mclk should be enabled in advance.
RK1000's control register block should be registered before RK1000
TVE.
Change-Id: Iba9a2a410fe927666072f8d246995462a860ec3a
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
1. Fix disconnect issue during system suspend
2. Add more module support
3. fix read country code from config
4. modify config.txt reading behavior
Change-Id: Ib6392523752d9af60329df0dd810ceb8b76467ff
Signed-off-by: Xu Xuehui <xxh@rock-chips.com>
Fixes:
error: redefinition of 'rockchip_drm_backlight_update'
error: redefinition of 'of_rockchip_drm_sub_backlight_register'
Change-Id: I4eeebc6075387f720acec597cee765e2a1a83b7c
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
