We could quickly reproduce this bug by decrease IO_TLB_DEFAULT_SIZE
and manually disable mmc DTO interrupt which can make driver fall into
post_tmo all the time.
So, some of these dump for swiotlb we can get here due to no enough
IO_TLB can be used to map page for kernel space:
DMA: Out of SW-IOMMU space for 128 bytes at device ff0f0000.rksdmmc
DMA: Out of SW-IOMMU space for 128 bytes at device ff0f0000.rksdmmc
...
DMA: Out of SW-IOMMU space for 128 bytes at device ff0f0000.rksdmmc
DMA: Out of SW-IOMMU space for 128 bytes at device ff0f0000.rksdmmc
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reported-and-tested-by: Jianhong Chen <chenjh@rock-chips.com>
Cc: Yao Xiao <xy@rock-chips.com>
when xrun occurs, it will do snd_pcm_stop to disable spdif
and then clear logic, next snd_pcm_lib_write1 will trigger
snd_pcm_start to enable spdif, but not to excute hw_params
to configue spdif, so need to save spdif configuration to
reconfigure spdif.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
When dwc controller change mode form device to host, may check_vbus_work is running
on other cpu, but we don't have a good synchronization id_status_change and
check_vbus_work, as a result, phy and clk may in incorrect state. So modify it.
Signed-off-by: Feng Mingli <fml@rock-chips.com>
Signed-off-by: lyz <lyz@rock-chips.com>
Conflicts:
drivers/usb/dwc_otg_310/dwc_otg_pcd_linux.c
changed codec register order according to IP datasheet to fix
right channel no output when low volume
Signed-off-by: luoxt <lxt@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Recently I came across high fragmentation of vm_map_ram allocator:
vmap_block has free space, but still new blocks continue to appear.
Further investigation showed that certain mapping/unmapping sequences
can exhaust vmalloc space. On small 32bit systems that's not a big
problem, cause purging will be called soon on a first allocation failure
(alloc_vmap_area), but on 64bit machines, e.g. x86_64 has 45 bits of
vmalloc space, that can be a disaster.
1) I came up with a simple allocation sequence, which exhausts virtual
space very quickly:
while (iters) {
/* Map/unmap big chunk */
vaddr = vm_map_ram(pages, 16, -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, 16);
/* Map/unmap small chunks.
*
* -1 for hole, which should be left at the end of each block
* to keep it partially used, with some free space available */
for (i = 0; i < (VMAP_BBMAP_BITS - 16) / 8 - 1; i++) {
vaddr = vm_map_ram(pages, 8, -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, 8);
}
}
The idea behind is simple:
1. We have to map a big chunk, e.g. 16 pages.
2. Then we have to occupy the remaining space with smaller chunks, i.e.
8 pages. At the end small hole should remain to keep block in free list,
but do not let big chunk to occupy remaining space.
3. Goto 1 - allocation request of 16 pages can't be completed (only 8 slots
are left free in the block in the #2 step), new block will be allocated,
all further requests will lay into newly allocated block.
To have some measurement numbers for all further tests I setup ftrace and
enabled 4 basic calls in a function profile:
echo vm_map_ram > /sys/kernel/debug/tracing/set_ftrace_filter;
echo alloc_vmap_area >> /sys/kernel/debug/tracing/set_ftrace_filter;
echo vm_unmap_ram >> /sys/kernel/debug/tracing/set_ftrace_filter;
echo free_vmap_block >> /sys/kernel/debug/tracing/set_ftrace_filter;
So for this scenario I got these results:
BEFORE (all new blocks are put to the head of a free list)
# cat /sys/kernel/debug/tracing/trace_stat/function0
Function Hit Time Avg s^2
-------- --- ---- --- ---
vm_map_ram 126000 30683.30 us 0.243 us 30819.36 us
vm_unmap_ram 126000 22003.24 us 0.174 us 340.886 us
alloc_vmap_area 1000 4132.065 us 4.132 us 0.903 us
AFTER (all new blocks are put to the tail of a free list)
# cat /sys/kernel/debug/tracing/trace_stat/function0
Function Hit Time Avg s^2
-------- --- ---- --- ---
vm_map_ram 126000 28713.13 us 0.227 us 24944.70 us
vm_unmap_ram 126000 20403.96 us 0.161 us 1429.872 us
alloc_vmap_area 993 3916.795 us 3.944 us 29.370 us
free_vmap_block 992 654.157 us 0.659 us 1.273 us
SUMMARY:
The most interesting numbers in those tables are numbers of block
allocations and deallocations: alloc_vmap_area and free_vmap_block
calls, which show that before the change blocks were not freed, and
virtual space and physical memory (vmap_block structure allocations,
etc) were consumed.
Average time which were spent in vm_map_ram/vm_unmap_ram became slightly
better. That can be explained with a reasonable amount of blocks in a
free list, which we need to iterate to find a suitable free block.
2) Another scenario is a random allocation:
while (iters) {
/* Randomly take number from a range [1..32/64] */
nr = rand(1, VMAP_MAX_ALLOC);
vaddr = vm_map_ram(pages, nr, -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, nr);
}
I chose mersenne twister PRNG to generate persistent random state to
guarantee that both runs have the same random sequence. For each
vm_map_ram call random number from [1..32/64] was taken to represent
amount of pages which I do map.
I did 10'000 vm_map_ram calls and got these two tables:
BEFORE (all new blocks are put to the head of a free list)
# cat /sys/kernel/debug/tracing/trace_stat/function0
Function Hit Time Avg s^2
-------- --- ---- --- ---
vm_map_ram 10000 10170.01 us 1.017 us 993.609 us
vm_unmap_ram 10000 5321.823 us 0.532 us 59.789 us
alloc_vmap_area 420 2150.239 us 5.119 us 3.307 us
free_vmap_block 37 159.587 us 4.313 us 134.344 us
AFTER (all new blocks are put to the tail of a free list)
# cat /sys/kernel/debug/tracing/trace_stat/function0
Function Hit Time Avg s^2
-------- --- ---- --- ---
vm_map_ram 10000 7745.637 us 0.774 us 395.229 us
vm_unmap_ram 10000 5460.573 us 0.546 us 67.187 us
alloc_vmap_area 414 2201.650 us 5.317 us 5.591 us
free_vmap_block 412 574.421 us 1.394 us 15.138 us
SUMMARY:
'BEFORE' table shows, that 420 blocks were allocated and only 37 were
freed. Remained 383 blocks are still in a free list, consuming virtual
space and physical memory.
'AFTER' table shows, that 414 blocks were allocated and 412 were really
freed. 2 blocks remained in a free list.
So fragmentation was dramatically reduced. Why? Because when we put
newly allocated block to the head, all further requests will occupy new
block, regardless remained space in other blocks. In this scenario all
requests come randomly. Eventually remained free space will be less
than requested size, free list will be iterated and it is possible that
nothing will be found there - finally new block will be created. So
exhaustion in random scenario happens for the maximum possible
allocation size: 32 pages for 32-bit system and 64 pages for 64-bit
system.
Also average cost of vm_map_ram was reduced from 1.017 us to 0.774 us.
Again this can be explained by iteration through smaller list of free
blocks.
3) Next simple scenario is a sequential allocation, when the allocation
order is increased for each block. This scenario forces allocator to
reach maximum amount of partially free blocks in a free list:
while (iters) {
/* Populate free list with blocks with remaining space */
for (order = 0; order <= ilog2(VMAP_MAX_ALLOC); order++) {
nr = VMAP_BBMAP_BITS / (1 << order);
/* Leave a hole */
nr -= 1;
for (i = 0; i < nr; i++) {
vaddr = vm_map_ram(pages, (1 << order), -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, (1 << order));
}
/* Completely occupy blocks from a free list */
for (order = 0; order <= ilog2(VMAP_MAX_ALLOC); order++) {
vaddr = vm_map_ram(pages, (1 << order), -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, (1 << order));
}
}
Results which I got:
BEFORE (all new blocks are put to the head of a free list)
# cat /sys/kernel/debug/tracing/trace_stat/function0
Function Hit Time Avg s^2
-------- --- ---- --- ---
vm_map_ram 2032000 399545.2 us 0.196 us 467123.7 us
vm_unmap_ram 2032000 363225.7 us 0.178 us 111405.9 us
alloc_vmap_area 7001 30627.76 us 4.374 us 495.755 us
free_vmap_block 6993 7011.685 us 1.002 us 159.090 us
AFTER (all new blocks are put to the tail of a free list)
# cat /sys/kernel/debug/tracing/trace_stat/function0
Function Hit Time Avg s^2
-------- --- ---- --- ---
vm_map_ram 2032000 394259.7 us 0.194 us 589395.9 us
vm_unmap_ram 2032000 292500.7 us 0.143 us 94181.08 us
alloc_vmap_area 7000 31103.11 us 4.443 us 703.225 us
free_vmap_block 7000 6750.844 us 0.964 us 119.112 us
SUMMARY:
No surprises here, almost all numbers are the same.
Fixing this fragmentation problem I also did some improvements in a
allocation logic of a new vmap block: occupy block immediately and get
rid of extra search in a free list.
Also I replaced dirty bitmap with min/max dirty range values to make the
logic simpler and slightly faster, since two longs comparison costs
less, than loop thru bitmap.
This patchset raises several questions:
Q: Think the problem you comments is already known so that I wrote comments
about it as "it could consume lots of address space through fragmentation".
Could you tell me about your situation and reason why it should be avoided?
Gioh Kim
A: Indeed, there was a commit 364376383 which adds explicit comment about
fragmentation. But fragmentation which is described in this comment caused
by mixing of long-lived and short-lived objects, when a whole block is pinned
in memory because some page slots are still in use. But here I am talking
about blocks which are free, nobody uses them, and allocator keeps them alive
forever, continuously allocating new blocks.
Q: I think that if you put newly allocated block to the tail of a free
list, below example would results in enormous performance degradation.
new block: 1MB (256 pages)
while (iters--) {
vm_map_ram(3 or something else not dividable for 256) * 85
vm_unmap_ram(3) * 85
}
On every iteration, it needs newly allocated block and it is put to the
tail of a free list so finding it consumes large amount of time.
Joonsoo Kim
A: Second patch in current patchset gets rid of extra search in a free list,
so new block will be immediately occupied..
Also, the scenario above is impossible, cause vm_map_ram allocates virtual
range in orders, i.e. 2^n. I.e. passing 3 to vm_map_ram you will allocate
4 slots in a block and 256 slots (capacity of a block) of course dividable
on 4, so block will be completely occupied.
But there is a worst case which we can achieve: each free block has a hole
equal to order size.
The maximum size of allocation is 64 pages for 64-bit system
(if you try to map more, original alloc_vmap_area will be called).
So the maximum order is 6. That means that worst case, before allocator
makes a decision to allocate a new block, is to iterate 7 blocks:
HEAD
1st block - has 1 page slot free (order 0)
2nd block - has 2 page slots free (order 1)
3rd block - has 4 page slots free (order 2)
4th block - has 8 page slots free (order 3)
5th block - has 16 page slots free (order 4)
6th block - has 32 page slots free (order 5)
7th block - has 64 page slots free (order 6)
TAIL
So the worst scenario on 64-bit system is that each CPU queue can have 7
blocks in a free list.
This can happen only and only if you allocate blocks increasing the order.
(as I did in the function written in the comment of the first patch)
This is weird and rare case, but still it is possible. Afterwards you will
get 7 blocks in a list.
All further requests should be placed in a newly allocated block or some
free slots should be found in a free list.
Seems it does not look dramatically awful.
This patch (of 3):
If suitable block can't be found, new block is allocated and put into a
head of a free list, so on next iteration this new block will be found
first.
That's bad, because old blocks in a free list will not get a chance to be
fully used, thus fragmentation will grow.
Let's consider this simple example:
#1 We have one block in a free list which is partially used, and where only
one page is free:
HEAD |xxxxxxxxx-| TAIL
^
free space for 1 page, order 0
#2 New allocation request of order 1 (2 pages) comes, new block is allocated
since we do not have free space to complete this request. New block is put
into a head of a free list:
HEAD |----------|xxxxxxxxx-| TAIL
#3 Two pages were occupied in a new found block:
HEAD |xx--------|xxxxxxxxx-| TAIL
^
two pages mapped here
#4 New allocation request of order 0 (1 page) comes. Block, which was created
on #2 step, is located at the beginning of a free list, so it will be found
first:
HEAD |xxX-------|xxxxxxxxx-| TAIL
^ ^
page mapped here, but better to use this hole
It is obvious, that it is better to complete request of #4 step using the
old block, where free space is left, because in other case fragmentation
will be highly increased.
But fragmentation is not only the case. The worst thing is that I can
easily create scenario, when the whole vmalloc space is exhausted by
blocks, which are not used, but already dirty and have several free pages.
Let's consider this function which execution should be pinned to one CPU:
static void exhaust_virtual_space(struct page *pages[16], int iters)
{
/* Firstly we have to map a big chunk, e.g. 16 pages.
* Then we have to occupy the remaining space with smaller
* chunks, i.e. 8 pages. At the end small hole should remain.
* So at the end of our allocation sequence block looks like
* this:
* XX big chunk
* |XXxxxxxxx-| x small chunk
* - hole, which is enough for a small chunk,
* but is not enough for a big chunk
*/
while (iters--) {
int i;
void *vaddr;
/* Map/unmap big chunk */
vaddr = vm_map_ram(pages, 16, -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, 16);
/* Map/unmap small chunks.
*
* -1 for hole, which should be left at the end of each block
* to keep it partially used, with some free space available */
for (i = 0; i < (VMAP_BBMAP_BITS - 16) / 8 - 1; i++) {
vaddr = vm_map_ram(pages, 8, -1, PAGE_KERNEL);
vm_unmap_ram(vaddr, 8);
}
}
}
On every iteration new block (1MB of vm area in my case) will be
allocated and then will be occupied, without attempt to resolve small
allocation request using previously allocated blocks in a free list.
In case of random allocation (size should be randomly taken from the
range [1..64] in 64-bit case or [1..32] in 32-bit case) situation is the
same: new blocks continue to appear if maximum possible allocation size
(32 or 64) passed to the allocator, because all remaining blocks in a
free list do not have enough free space to complete this allocation
request.
In summary if new blocks are put into the head of a free list eventually
virtual space will be exhausted.
In current patch I simply put newly allocated block to the tail of a
free list, thus reduce fragmentation, giving a chance to resolve
allocation request using older blocks with possible holes left.
Signed-off-by: Roman Pen <r.peniaev@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: David Rientjes <rientjes@google.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Christoph Lameter <cl@linux.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: Rob Jones <rob.jones@codethink.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When sending avi introduced by commit 132ad528d0,
we polling avi sending status register until avi is send, instead of delay 100ms.
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
add parameter of lcdc type for mcu to fix HDMI display abnormal when do ddr
change freq. it must update bl30 to rk3368bl30_v2.09.bin at the same time.
Signed-off-by: Tang Yun ping <typ@rock-chips.com>
If we don't add lvds_format on the display timing, the lvds_format
value may be -1, means 0xffffffff when do register write, that is
wrong and display not works.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
It is required to perform a reset tmdsclk action on one of the frame composer
registers changed. Or transport video and audio sample may mistake.
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
usage: add i2s dts property "rockchip,xfer-mode"
rockchip,xfer-mode = <0>: i2s transfer mode.
rockchip,xfer-mode = <1>: pcm transfer mode.
if not define, use i2s transfer mode default.
pcm transfer mode is usually used for bt/modem voice.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
