[ Upstream commit 64b7871522a4cba99d092e1c849d6f9092868aaa ]
This patch addresses an issue where authentication failures were being
erroneously reported due to negative test failures in the "ccm(aes)"
selftest.
pr_debug suppress unnecessary screaming of these tests.
Signed-off-by: Shashank Gupta <shashankg@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f757f6011c92b5a01db742c39149bed9e526478f ]
The script previously assumed --file was always the first argument,
which caused issues when it appeared later. This patch updates the
parsing logic to scan all arguments to find --file, sets the config
file correctly, and resets the argument list with the remaining
commands.
It also fixes --refresh to respect --file by passing KCONFIG_CONFIG=$FN
to make oldconfig.
Signed-off-by: Seyediman Seyedarab <imandevel@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad79c278e478ca8c1a3bf8e7a0afba8f862a48a1 ]
This is only used to write a new NVM in order to upgrade the retimer
firmware. It does not make sense to expose it if upgrade is disabled.
This also makes it consistent with the router NVM upgrade.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 149dfb31615e22271d2525f078c95ea49bc4db24 ]
- Move tcp_count_delivered() earlier and split tcp_count_delivered_ce()
out of it
- Move tcp_in_ack_event() later
- While at it, remove the inline from tcp_in_ack_event() and let
the compiler to decide
Accurate ECN's heuristics does not know if there is going
to be ACE field based CE counter increase or not until after
rtx queue has been processed. Only then the number of ACKed
bytes/pkts is available. As CE or not affects presence of
FLAG_ECE, that information for tcp_in_ack_event is not yet
available in the old location of the call to tcp_in_ack_event().
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 860be250fc32de9cb24154bf21b4e36f40925707 ]
Some systems report INTx as not routed by setting pdev->irq to
IRQ_NOTCONNECTED, resulting in a -ENOTCONN error when trying to
setup eventfd signaling. Include this in the set of conditions
for which the PIN register is virtualized to zero.
Additionally consolidate vfio_pci_get_irq_count() to use this
virtualized value in reporting INTx support via ioctl and sanity
checking ioctl paths since pdev->irq is re-used when the device
is in MSI mode.
The combination of these results in both the config space of the
device and the ioctl interface behaving as if the device does not
support INTx.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20250311230623.1264283-1-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8db816c6f176321e42254badd5c1a8df8bfcfdb4 ]
In the days when SCSI-2 was emerging, some drives did claim SCSI-2 but did
not correctly implement it. The st driver first tries MODE SELECT with the
page format bit set to set the block descriptor. If not successful, the
non-page format is tried.
The test only tests the sense code and this triggers also from illegal
parameter in the parameter list. The test is limited to "old" devices and
made more strict to remove false alarms.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250311112516.5548-4-Kai.Makisara@kolumbus.fi
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b419c889c0767a5b66d0a6c566cae491f1cb0f7 ]
capable() calls refer to enabled LSMs whether to permit or deny the
request. This is relevant in connection with SELinux, where a
capability check results in a policy decision and by default a denial
message on insufficient permission is issued.
It can lead to three undesired cases:
1. A denial message is generated, even in case the operation was an
unprivileged one and thus the syscall succeeded, creating noise.
2. To avoid the noise from 1. the policy writer adds a rule to ignore
those denial messages, hiding future syscalls, where the task
performs an actual privileged operation, leading to hidden limited
functionality of that task.
3. To avoid the noise from 1. the policy writer adds a rule to permit
the task the requested capability, while it does not need it,
violating the principle of least privilege.
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250302160657.127253-2-cgoettsche@seltendoof.de
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cef721e0d53d2b64f2ba177c63a0dfdd7c0daf17 ]
Doing this allows using registers as retrieved from an mcontext to be
pushed to a process using PTRACE_SETREGS.
It is not entirely clear to me why CSGSFS was masked. Doing so creates
issues when using the mcontext as process state in seccomp and simply
copying the register appears to work perfectly fine for ptrace.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Link: https://patch.msgid.link/20250224181827.647129-2-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03d2b62208a336a3bb984b9465ef6d89a046ea22 ]
This patch bypasses multi-link errors in TCP mode, allowing dlm
to operate on the first tcp link.
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c2f4ae64bb6f6d83a54d88b9ee0f369cdbb9fa8 ]
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Eric Yang <eric.yang@amd.com>
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a77749b3e21813566cea050bbb3414ae74562eba ]
When attempting to build a too long path we are currently returning
-ENOMEM, which is very odd and misleading. So update fs_path_ensure_buf()
to return -ENAMETOOLONG instead. Also, while at it, move the WARN_ON()
into the if statement's expression, as it makes it clear what is being
tested and also has the effect of adding 'unlikely' to the statement,
which allows the compiler to generate better code as this condition is
never expected to happen.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1283b8c125a83bf7a7dbe90c33d3472b6d7bf612 ]
At btrfs_reclaim_bgs_work(), we are grabbing a block group's zone unusable
bytes while not under the protection of the block group's spinlock, so
this can trigger race reports from KCSAN (or similar tools) since that
field is typically updated while holding the lock, such as at
__btrfs_add_free_space_zoned() for example.
Fix this by grabbing the zone unusable bytes while we are still in the
critical section holding the block group's spinlock, which is right above
where we are currently grabbing it.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cda76788f8b0f7de3171100e3164ec1ce702292e ]
At close_ctree() after we have ran delayed iputs either explicitly through
calling btrfs_run_delayed_iputs() or later during the call to
btrfs_commit_super() or btrfs_error_commit_super(), we assert that the
delayed iputs list is empty.
We have (another) race where this assertion might fail because we have
queued an async write into the fs_info->workers workqueue. Here's how it
happens:
1) We are submitting a data bio for an inode that is not the data
relocation inode, so we call btrfs_wq_submit_bio();
2) btrfs_wq_submit_bio() submits a work for the fs_info->workers queue
that will run run_one_async_done();
3) We enter close_ctree(), flush several work queues except
fs_info->workers, explicitly run delayed iputs with a call to
btrfs_run_delayed_iputs() and then again shortly after by calling
btrfs_commit_super() or btrfs_error_commit_super(), which also run
delayed iputs;
4) run_one_async_done() is executed in the work queue, and because there
was an IO error (bio->bi_status is not 0) it calls btrfs_bio_end_io(),
which drops the final reference on the associated ordered extent by
calling btrfs_put_ordered_extent() - and that adds a delayed iput for
the inode;
5) At close_ctree() we find that after stopping the cleaner and
transaction kthreads the delayed iputs list is not empty, failing the
following assertion:
ASSERT(list_empty(&fs_info->delayed_iputs));
Fix this by flushing the fs_info->workers workqueue before running delayed
iputs at close_ctree().
David reported this when running generic/648, which exercises IO error
paths by using the DM error table.
Reported-by: David Sterba <dsterba@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df94a342efb451deb0e32b495d1d6cd4bb3a1648 ]
[BUG]
Even after all the error fixes related the
"ASSERT(list_empty(&fs_info->delayed_iputs));" in close_ctree(), I can
still hit it reliably with my experimental 2K block size.
[CAUSE]
In my case, all the error is triggered after the fs is already in error
status.
I find the following call trace to be the cause of race:
Main thread | endio_write_workers
---------------------------------------------+---------------------------
close_ctree() |
|- btrfs_error_commit_super() |
| |- btrfs_cleanup_transaction() |
| | |- btrfs_destroy_all_ordered_extents() |
| | |- btrfs_wait_ordered_roots() |
| |- btrfs_run_delayed_iputs() |
| | btrfs_finish_ordered_io()
| | |- btrfs_put_ordered_extent()
| | |- btrfs_add_delayed_iput()
|- ASSERT(list_empty(delayed_iputs)) |
!!! Triggered !!!
The root cause is that, btrfs_wait_ordered_roots() only wait for
ordered extents to finish their IOs, not to wait for them to finish and
removed.
[FIX]
Since btrfs_error_commit_super() will flush and wait for all ordered
extents, it should be executed early, before we start flushing the
workqueues.
And since btrfs_error_commit_super() now runs early, there is no need to
run btrfs_run_delayed_iputs() inside it, so just remove the
btrfs_run_delayed_iputs() call from btrfs_error_commit_super().
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ef3cbf17d2734ca66c4ed8573be45f4e461e7ee ]
The inline function btrfs_is_testing() is hardcoded to return 0 if
CONFIG_BTRFS_FS_RUN_SANITY_TESTS is not set. Currently we're relying on
the compiler optimizing out the call to alloc_test_extent_buffer() in
btrfs_find_create_tree_block(), as it's not been defined (it's behind an
#ifdef).
Add a stub version of alloc_test_extent_buffer() to avoid linker errors
on non-standard optimization levels. This problem was seen on GCC 14
with -O0 and is helps to see symbols that would be otherwise optimized
out.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Mark Harmstone <maharmstone@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 895c6721d310c036dcfebb5ab845822229fa35eb ]
Currently, the async discard machinery owns a ref to the block_group
when the block_group is queued on a discard list. However, to handle
races with discard cancellation and the discard workfn, we have a
specific logic to detect that the block_group is *currently* running in
the workfn, to protect the workfn's usage amidst cancellation.
As far as I can tell, this doesn't have any overt bugs (though
finish_discard_pass() and remove_from_discard_list() racing can have a
surprising outcome for the caller of remove_from_discard_list() in that
it is again added at the end).
But it is needlessly complicated to rely on locking and the nullity of
discard_ctl->block_group. Simplify this significantly by just taking a
refcount while we are in the workfn and unconditionally drop it in both
the remove and workfn paths, regardless of if they race.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f35233a6345f62637463ef6e0708f44ffaa583 ]
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa9473019 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20231128-i2c-qup-dvfs-v1-3-59a0e3039111@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 631ca8909fd5c62b9fda9edda93924311a78a9c4 ]
At least with CONFIG_PHYSICAL_START=0x100000, if there is < 4 MiB of
contiguous free memory available at this point, the kernel will crash
and burn because memblock_phys_alloc_range() returns 0 on failure,
which leads memblock_phys_free() to throw the first 4 MiB of physical
memory to the wolves.
At a minimum it should fail gracefully with a meaningful diagnostic,
but in fact everything seems to work fine without the weird reserve
allocation.
Signed-off-by: Philip Redkin <me@rarity.fan>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/94b3e98f-96a7-3560-1f76-349eb95ccf7f@rarity.fan
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31e75ed964582257f59156ce6a42860e1ae4cc39 ]
The SD spec version 6.0 section 6.4.1.5 requires that Vdd must be
lowered to less than 0.5V for a minimum of 1 ms when powering off a
card. Increase wait to 15 ms so that voltage has time to drain down
to 0.5V and cards can power off correctly. Issues with voltage drain
time were only observed on Apollo Lake and Bay Trail host controllers
so this fix is limited to those devices.
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250314195021.1588090-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef1d3455bbc1922f94a91ed58d3d7db440652959 ]
If a faulty CXL memory device returns a broken zero LSA size in its
memory device information (Identify Memory Device (Opcode 4000h), CXL
spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm
driver:
Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:nd_label_data_init+0x10e/0x800 [libnvdimm]
Code and flow:
1) CXL Command 4000h returns LSA size = 0
2) config_size is assigned to zero LSA size (CXL pmem driver):
drivers/cxl/pmem.c: .config_size = mds->lsa_size,
3) max_xfer is set to zero (nvdimm driver):
drivers/nvdimm/label.c: max_xfer = min_t(size_t, ndd->nsarea.max_xfer, config_size);
4) A subsequent DIV_ROUND_UP() causes a division by zero:
drivers/nvdimm/label.c: /* Make our initial read size a multiple of max_xfer size */
drivers/nvdimm/label.c: read_size = min(DIV_ROUND_UP(read_size, max_xfer) * max_xfer,
drivers/nvdimm/label.c- config_size);
Fix this by checking the config size parameter by extending an
existing check.
Signed-off-by: Robert Richter <rrichter@amd.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://patch.msgid.link/20250320112223.608320-1-rrichter@amd.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c4d5aadf5df31ea0ac025980670eee9beaf466b ]
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-3-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa42add73ce9b9e3714723d385c254b75814e335 ]
If the client should see an ENETDOWN when trying to connect to the data
server, it might still be able to talk to the metadata server through
another NIC. If so, report the error.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Jeff Layton <jlayton@kernel.org>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3e1dccba0a0833fc9a05fb838ebeb6ea4ca0e1a ]
Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
Link: https://lore.kernel.org/r/20250315201548.858189-12-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61c39d8c83e2077f33e0a2c8980a76a7f323f0ce ]
Since:
0c1d7a2c2d ("lockdep: Remove softirq accounting on PREEMPT_RT.")
the wait context test for mutex usage within "in softirq context" fails
as it references @softirq_context:
| wait context tests |
--------------------------------------------------------------------------
| rcu | raw | spin |mutex |
--------------------------------------------------------------------------
in hardirq context: ok | ok | ok | ok |
in hardirq context (not threaded): ok | ok | ok | ok |
in softirq context: ok | ok | ok |FAILED|
As a fix, add lockdep map for BH disabled section. This fixes the
issue by letting us catch cases when local_bh_disable() gets called
with preemption disabled where local_lock doesn't get acquired.
In the case of "in softirq context" selftest, local_bh_disable() was
being called with preemption disable as it's early in the boot.
[ boqun: Move the lockdep annotations into __local_bh_*() to avoid false
positives because of unpaired local_bh_disable() reported by
Borislav Petkov and Peter Zijlstra, and make bh_lock_map
only exist for PREEMPT_RT. ]
[ mingo: Restored authorship and improved the bh_lock_map definition. ]
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250321143322.79651-1-boqun.feng@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a17f23f7c36bac3a3584aaf97d3e3e0b2790396 ]
Executing dql_reset after setting a non-zero value for limit_min can
lead to an unreasonable situation where dql->limit is less than
dql->limit_min.
For instance, after setting
/sys/class/net/eth*/queues/tx-0/byte_queue_limits/limit_min,
an ifconfig down/up operation might cause the ethernet driver to call
netdev_tx_reset_queue, which in turn invokes dql_reset.
In this case, dql->limit is reset to 0 while dql->limit_min remains
non-zero value, which is unexpected. The limit should always be
greater than or equal to limit_min.
Signed-off-by: Jing Su <jingsusu@didiglobal.com>
Link: https://patch.msgid.link/Z9qHD1s/NEuQBdgH@pilot-ThinkCentre-M930t-N000
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 214c13e380ad7636631279f426387f9c4e3c14d9 ]
If we already had a valid port number for the RPC service, then we
should not allow the rpcbind client to set it to the invalid value '0'.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf9be373b830a3e48117da5d89bb6145a575f880 ]
The autobind setting was supposed to be determined in rpc_create(),
since commit c2866763b4 ("SUNRPC: use sockaddr + size when creating
remote transport endpoints").
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0af5fb5ed3d2fd9e110c6112271f022b744a849a ]
If a containerised process is killed and causes an ENETUNREACH or
ENETDOWN error to be propagated to the state manager, then mark the
nfs_client as being dead so that we don't loop in functions that are
expecting recovery to succeed.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 781802aa5a5950f99899f13ff9d760f5db81d36d ]
Function ip_rfc1001_connect() which establish NetBIOS session for SMB
connections, currently uses smb_send() function for sending NetBIOS Session
Request packet. This function expects that the passed buffer is SMB packet
and for SMB2+ connections it mangles packet header, which breaks prepared
NetBIOS Session Request packet. Result is that this function send garbage
packet for SMB2+ connection, which SMB2+ server cannot parse. That function
is not mangling packets for SMB1 connections, so it somehow works for SMB1.
Fix this problem and instead of smb_send(), use smb_send_kvec() function
which does not mangle prepared packet, this function send them as is. Just
API of this function takes struct msghdr (kvec) instead of packet buffer.
[MS-SMB2] specification allows SMB2 protocol to use NetBIOS as a transport
protocol. NetBIOS can be used over TCP via port 139. So this is a valid
configuration, just not so common. And even recent Windows versions (e.g.
Windows Server 2022) still supports this configuration: SMB over TCP port
139, including for modern SMB2 and SMB3 dialects.
This change fixes SMB2 and SMB3 connections over TCP port 139 which
requires establishing of NetBIOS session. Tested that this change fixes
establishing of SMB2 and SMB3 connections with Windows Server 2022.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76d3ca89981354e1f85a3e0ad9ac4217d351cc72 ]
I was wondering why there's garbage at the bottom of the screen when
tile blitting is used with an odd mode like 1080, 600 or 200. Sure there's
only space for half a tile but the same area is clean when the buffer
is bitmap.
Then later I found that it's supposed to be cleaned but that's not
implemented. So I took what's in bitblit and adapted it for tileblit.
This implementation was tested for both the horizontal and vertical case,
and now does the same as what's done for bitmap buffers.
If anyone is interested to reproduce the problem then I could bet that'd
be on a S3 or Ark. Just set up a mode with an odd line count and make
sure that the virtual size covers the complete tile at the bottom. E.g.
for 600 lines that's 608 virtual lines for a 16 tall tile. Then the
bottom area should be cleaned.
For the right side it's more difficult as there the drivers won't let an
odd size happen, unless the code is modified. But once it reports back a
few pixel columns short then fbcon won't use the last column. With the
patch that column is now clean.
Btw. the virtual size should be rounded up by the driver for both axes
(not only the horizontal) so that it's dividable by the tile size.
That's a driver bug but correcting it is not in scope for this patch.
Implement missing margin clearing for tileblit
Signed-off-by: Zsolt Kajtar <soci@c64.rulez.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 892c788d73fe4a94337ed092cb998c49fa8ecaf4 ]
The erase colour calculation for fbcon clearing should use get_color instead
of attr_col_ec, like everything else. The latter is similar but is not correct.
For example it's missing the depth dependent remapping and doesn't care about
blanking.
The problem can be reproduced by setting up the background colour to grey
(vt.color=0x70) and having an fbcon console set to 2bpp (4 shades of gray).
Now the background attribute should be 1 (dark gray) on the console.
If the screen is scrolled when pressing enter in a shell prompt at the bottom
line then the new line is cleared using colour 7 instead of 1. That's not
something fillrect likes (at 2bbp it expect 0-3) so the result is interesting.
This patch switches to get_color with vc_video_erase_char to determine the
erase colour from attr_col_ec. That makes the latter function redundant as
no other users were left.
Use correct erase colour for clearing in fbcon
Signed-off-by: Zsolt Kajtar <soci@c64.rulez.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24fdd5074b205cfb0ef4cd0751a2d03031455929 ]
In case of error, of_parse_phandle_with_args() returns -EINVAL when the
passed index is negative, or -ENOENT when the index is for an empty
phandle. The mailbox core overwrote the error return code with a less
precise -ENODEV. Use the error returned code from
of_parse_phandle_with_args().
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196a062641fe68d9bfe0ad36b6cd7628c99ad22c ]
Binary printing functions are using printf() type of format, and compiler
is not happy about them as is:
kernel/trace/trace.c:3292:9: error: function ‘trace_vbprintk’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
kernel/trace/trace_seq.c:182:9: error: function ‘trace_seq_bprintf’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
Fix the compilation errors by adding __printf() attribute.
While at it, move existing __printf() attributes from the implementations
to the declarations. IT also fixes incorrect attribute parameters that are
used for trace_array_printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250321144822.324050-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14e41b16e8cb677bb440dca2edba8b041646c742 ]
Once a task calls exit_signals() it can no longer be signalled. So do
not allow it to do killable waits.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3ca331026a7f9700d3747eed59a67b8f828cdc ]
Once a task calls exit_signals() it can no longer be signalled. So do
not allow it to do killable waits.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e8f324bd44c1fe026b582b75213de4eccfa1163 ]
Check that the delegation is still attached after taking the spin lock
in nfs_start_delegation_return_locked().
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e94e882a6d69525c07589222cf3a6ff57ad12b5b ]
SMB negotiate retry functionality in cifs_negotiate() is currently broken
and does not work when doing socket reconnect. Caller of this function,
which is cifs_negotiate_protocol() requires that tcpStatus after successful
execution of negotiate callback stay in CifsInNegotiate. But if the
CIFSSMBNegotiate() called from cifs_negotiate() fails due to connection
issues then tcpStatus is changed as so repeated CIFSSMBNegotiate() call
does not help.
Fix this problem by moving retrying code from negotiate callback (which is
either cifs_negotiate() or smb2_negotiate()) to cifs_negotiate_protocol()
which is caller of those callbacks. This allows to properly handle and
implement correct transistions between tcpStatus states as function
cifs_negotiate_protocol() already handles it.
With this change, cifs_negotiate_protocol() now handles also -EAGAIN error
set by the RFC1002_NEGATIVE_SESSION_RESPONSE processing after reconnecting
with NetBIOS session.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
