[ Upstream commit 2371adeab7 ]
Add the check for the return value of the create_workqueue
in order to avoid NULL pointer dereference.
Fixes: 28ffeebbb7 ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1cdec319 ]
Thee maximum number of MCA banks is 64 (MAX_NR_BANKS), see
a0bc32b3ca ("x86/mce: Increase maximum number of banks to 64").
However, the bank_map which contains a bitfield of which banks to
initialize is of type unsigned int and that overflows when those bit
numbers are >= 32, leading to UBSAN complaining correctly:
UBSAN: shift-out-of-bounds in arch/x86/kernel/cpu/mce/amd.c:1365:38
shift exponent 32 is too large for 32-bit type 'int'
Change the bank_map to a u64 and use the proper BIT_ULL() macro when
modifying bits in there.
[ bp: Rewrite commit message. ]
Fixes: a0bc32b3ca ("x86/mce: Increase maximum number of banks to 64")
Signed-off-by: Muralidhara M K <muralimk@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230127151601.1068324-1-muralimk@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fafb7e5c0 ]
The current value for pci IO is problematic for ath10k wifi card
commonly connected to ipq8064 SoC.
The current value is probably a typo and is actually uncommon to find
1MB IO space even on a x86 arch. Also with recent changes to the pci
driver, pci1 and pci2 now fails to function as any connected device
fails any reg read/write. Reduce this to 64K as it should be more than
enough and 3 * 64K of total IO space doesn't exceed the IO_SPACE_LIMIT
hardcoded for the ARM arch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220707010943.20857-7-ansuelsmth@gmail.com
Stable-dep-of: 0b16b34e49 ("ARM: dts: qcom: ipq8064: Fix the PCI I/O port range")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0a8e35d7 ]
Following sm8150/sm8250 update sdm845 capacity-dmips-mhz and
dynamic-power-coefficient based on the measurements [1], [2].
The energy model dynamic-power-coefficient values were calculated with
DPC = µW / MHz / V^2
for each OPP, and averaged across all OPPs within each cluster for the
final coefficient. Voltages were obtained from the qcom-cpufreq-hw
driver that reads voltages from the OSM LUT programmed into the SoC.
Normalized DMIPS/MHz capacity scale values for each CPU were calculated
from CoreMarks/MHz (CoreMark iterations per second per MHz), which
serves the same purpose. For each CPU, the final capacity-dmips-mhz
value is the C/MHz value of its maximum frequency normalized to
SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system.
For more details on measurement process see the commit message for the
commit 6aabed5526 ("arm64: dts: qcom: sm8250: Add CPU capacities and
energy model").
[1] https://github.com/kdrag0n/freqbench
[2] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main
Cc: Danny Lin <danny@kdrag0n.dev>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220315141104.730235-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71b1e3ba3f ]
The current DRAM row address mapping arrays skx_{open,close}_row[]
only support ranks with sizes up to 16G. Decoding a rank address
to a DRAM row address for a 32G rank by using either one of the
above arrays by the skx_edac driver, will result in an overflow on
the array.
For a 32G rank, the most significant DRAM row address bit (the
bit17) is mapped from the bit34 of the rank address. Add this new
mapping item to both arrays to fix the overflow issue.
Fixes: 4ec656bdf4 ("EDAC, skx_edac: Add EDAC driver for Skylake")
Reported-by: Feng Xu <feng.f.xu@intel.com>
Tested-by: Feng Xu <feng.f.xu@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/all/20230211011728.71764-1-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554edc3e92 ]
According to the RZ/G Series, 2nd Generation Hardware User’s Manual
Rev. 1.11, the System CPU cores on RZ/G2E do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Fixes: 231d8908a6 ("arm64: dts: renesas: r8a774c0: Add OPPs table for cpu devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8348e18a011ded94e35919cd8e17c0be1f9acf2f.1676560856.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb76b0fae3 ]
According to the R-Car Series, 3rd Generation Hardware User’s Manual
Rev. 2.30, the System CPU cores on R-Car E3 do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Fixes: dd7188eb4e ("arm64: dts: renesas: r8a77990: Add OPPs table for cpu devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9232578d9d395d529f64db3333a371e31327f459.1676560856.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e47884f1 ]
Currently we schedule a call to output_poll_execute from
drm_kms_helper_poll_enable for 10s in future. Later we try to replace
that in drm_helper_probe_single_connector_modes with a 0s schedule with
delayed_event set.
But as there is already a job in the queue this fails, and the immediate
job we wanted with delayed_event set doesn't occur until 10s later.
And that call acts as if connector state has changed, reprobing modes.
This has a side effect of waking up a display that has been blanked.
Make sure we cancel the old job before submitting the immediate one.
Fixes: 162b6a57ac ("drm/probe-helper: don't lose hotplug event")
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[Maxime: Switched to mod_delayed_work]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127154052.452524-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955df4f877 ]
In tpm_tis_resume() make sure that the locality has been claimed when
tpm_tis_reenable_interrupts() is called. Otherwise the writings to the
register might not have any effect.
Fixes: 45baa1d1fa ("tpm_tis: Re-enable interrupts upon (S3) resume")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a2f55d0be ]
Implement a usage counter for the (default) locality used by the TPM TIS
driver:
Request the locality from the TPM if it has not been claimed yet, otherwise
only increment the counter. Also release the locality if the counter is 0
otherwise only decrement the counter. Since in case of SPI the register
accesses are locked by means of the SPI bus mutex use a sleepable lock
(i.e. also a mutex) to ensure thread-safety of the counter which may be
accessed by both a userspace thread and the interrupt handler.
By doing this refactor the names of the amended functions to use a more
appropriate prefix.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d7aa4e46 ]
In tpm_tis_probe_single_irq() interrupt registers TPM_INT_VECTOR,
TPM_INT_STATUS and TPM_INT_ENABLE are modified to setup the interrupts.
Currently these modifications are done without holding a locality thus they
have no effect. Fix this by claiming the (default) locality before the
registers are written.
Since now tpm_tis_gen_interrupt() is called with the locality already
claimed remove locality request and release from this function.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d789ad726 ]
Both functions tpm_tis_probe_irq_single() and tpm_tis_probe_irq() may setup
the interrupts and then return with an error. This case is indicated by a
missing TPM_CHIP_FLAG_IRQ flag in chip->flags.
Currently the interrupt setup is only undone if tpm_tis_probe_irq_single()
fails. Undo the setup also if tpm_tis_probe_irq() fails.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 282657a8bd ]
In disable_interrupts() the TPM_GLOBAL_INT_ENABLE bit is unset in the
TPM_INT_ENABLE register to shut the interrupts off. However modifying the
register is only possible with a held locality. So claim the locality
before disable_interrupts() is called.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed9be0e6c8 ]
If in tpm_tis_probe_irq_single() an error occurs after the original
interrupt vector has been read, restore the interrupts before the error is
returned.
Since the caller does not check the error value, return -1 in any case that
the TPM_CHIP_FLAG_IRQ flag is not set. Since the return value of function
tpm_tis_gen_interrupt() is not longer used, make it a void function.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ce1f694eb ]
The Makefile rule responsible for building flask.h and
av_permissions.h only lists flask.h as a target which means that
av_permissions.h is only generated when flask.h needs to be
generated. This patch fixes this by adding av_permissions.h as a
target to the rule.
Fixes: 8753f6bec3 ("selinux: generate flask headers during kernel build")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcab1adeaa ]
Make the flask.h target depend on the genheaders binary instead of
classmap.h to ensure that it is rebuilt if any of the dependencies of
genheaders are changed.
Notably this fixes flask.h not being rebuilt when
initial_sid_to_string.h is modified.
Fixes: 8753f6bec3 ("selinux: generate flask headers during kernel build")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22a8be2803 ]
malloc_and_init_memory() in fill_buf isn't checking if memalign()
successfully allocated memory or not before accessing the memory.
Check the return value of memalign() and return NULL if allocating
aligned memory fails.
Fixes: a2561b12fe ("selftests/resctrl: Add built in benchmark")
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d46e04ccd4 upstream.
Always run the entire init sequence (rtl8xxxu_init_device()) for
RTL8192EU. It's what the vendor driver does too.
This fixes a bug where the device is unable to connect after
rebooting:
wlp3s0f3u2: send auth to ... (try 1/3)
wlp3s0f3u2: send auth to ... (try 2/3)
wlp3s0f3u2: send auth to ... (try 3/3)
wlp3s0f3u2: authentication with ... timed out
Rebooting leaves the device powered on (partially? at least the
firmware is still running), but not really in a working state.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/4eb111a9-d4c4-37d0-b376-4e202de7153c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a405c6f022 upstream.
init_resync() inits mempool and sets conf->have_replacemnt at the beginning
of sync, close_sync() frees the mempool when sync is completed.
After [1] recovery might be skipped and init_resync() is called but
close_sync() is not. null-ptr-deref occurs with r10bio->dev[i].repl_bio.
The following is one way to reproduce the issue.
1) create a array, wait for resync to complete, mddev->recovery_cp is set
to MaxSector.
2) recovery is woken and it is skipped. conf->have_replacement is set to
0 in init_resync(). close_sync() not called.
3) some io errors and rdev A is set to WantReplacement.
4) a new device is added and set to A's replacement.
5) recovery is woken, A have replacement, but conf->have_replacemnt is
0. r10bio->dev[i].repl_bio will not be alloced and null-ptr-deref
occurs.
Fix it by not calling init_resync() if recovery skipped.
[1] commit 7e83ccbecd ("md/raid10: Allow skipping recovery when clean arrays are assembled")
Fixes: 7e83ccbecd ("md/raid10: Allow skipping recovery when clean arrays are assembled")
Cc: stable@vger.kernel.org
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230222041000.3341651-3-linan666@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28a65b49eb upstream.
According to syzbot's report, mark_buffer_dirty() called from
nilfs_segctor_do_construct() outputs a warning with some patterns after
nilfs2 detects metadata corruption and degrades to read-only mode.
After such read-only degeneration, page cache data may be cleared through
nilfs_clear_dirty_page() which may also clear the uptodate flag for their
buffer heads. However, even after the degeneration, log writes are still
performed by unmount processing etc., which causes mark_buffer_dirty() to
be called for buffer heads without the "uptodate" flag and causes the
warning.
Since any writes should not be done to a read-only file system in the
first place, this fixes the warning in mark_buffer_dirty() by letting
nilfs_segctor_do_construct() abort early if in read-only mode.
This also changes the retry check of nilfs_segctor_write_out() to avoid
unnecessary log write retries if it detects -EROFS that
nilfs_segctor_do_construct() returned.
Link: https://lkml.kernel.org/r/20230427011526.13457-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+2af3bc9585be7f23f290@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=2af3bc9585be7f23f290
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e3220ba33 upstream.
Fix the argument pointer (ap) to point to real-mode memory
instead of virtual memory.
It's interesting that this issue hasn't shown up earlier, as this could
have happened with any 64-bit PDC ROM code.
I just noticed it because I suddenly faced a HPMC while trying to execute
the 64-bit STI ROM code of an Visualize-FXe graphics card for the STI
text console.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fb815b38b upstream.
When opening a ubifs tmpfile on an encrypted directory, function
fscrypt_setup_filename allocates memory for the name that is to be
stored in the directory entry, but after the name has been copied to the
directory entry inode, the memory is not freed.
When running kmemleak on it we see that it is registered as a leak. The
report below is triggered by a simple program 'tmpfile' just opening a
tmpfile:
unreferenced object 0xffff88810178f380 (size 32):
comm "tmpfile", pid 509, jiffies 4294934744 (age 1524.742s)
backtrace:
__kmem_cache_alloc_node
__kmalloc
fscrypt_setup_filename
ubifs_tmpfile
vfs_tmpfile
path_openat
Free this memory after it has been copied to the inode.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a149d5c1 upstream.
The commit 2d78aee426 ("UBI: simplify LEB write and atomic LEB change code")
adds helper function, try_write_vid_and_data(), to simplify the code, but this
helper function has bug, it will return 0 (success) when ubi_io_write_vid_hdr()
or the ubi_io_write_data() return error number (-EIO, etc), because the return
value of ubi_wl_put_peb() will overwrite the original return value.
This issue will cause unexpected data loss issue, because the caller of this
function and UBIFS willn't know the data is lost.
Fixes: 2d78aee426 ("UBI: simplify LEB write and atomic LEB change code")
Cc: stable@vger.kernel.org
Signed-off-by: Wang YanQing <udknight@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fda08ef2 upstream.
Following process will cause a memleak for copied up znode:
dirty_cow_znode
zn = copy_znode(c, znode);
err = insert_old_idx(c, zbr->lnum, zbr->offs);
if (unlikely(err))
return ERR_PTR(err); // No one refers to zn.
Fetch a reproducer in [Link].
Function copy_znode() is split into 2 parts: resource allocation
and znode replacement, insert_old_idx() is split in similar way,
so resource cleanup could be done in error handling path without
corrupting metadata(mem & disk).
It's okay that old index inserting is put behind of add_idx_dirt(),
old index is used in layout_leb_in_gaps(), so the two processes do
not depend on each other.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216705
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Cc: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d01cb27f6 upstream.
This reverts commit 122deabfe1 (ubifs: dirty_cow_znode: Fix memleak
in error handling path).
After commit 122deabfe1 applied, if insert_old_idx() failed, old
index neither exists in TNC nor in old-index tree. Which means that
old index node could be overwritten in layout_leb_in_gaps(), then
ubifs image will be corrupted in power-cut.
Fixes: 122deabfe1 (ubifs: dirty_cow_znode: Fix memleak ... path)
Cc: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccc62b8277 upstream.
commit b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC
(de-)activation code") while refactoring guest virtual APIC
activation/de-activation code, stored information for activate/de-activate
in "struct amd_ir_data". It used 32-bit integer data type for storing the
"Guest Virtual APIC Table Root Pointer" (ga_root_ptr), though the
"ga_root_ptr" is actually a 40-bit field in IRTE (Interrupt Remapping
Table Entry).
This causes interrupts from PCIe devices to not reach the guest in the case
of PCIe passthrough with SME (Secure Memory Encryption) enabled as _SME_
bit in the "ga_root_ptr" is lost before writing it to the IRTE.
Fix it by using 64-bit data type for storing the "ga_root_ptr". While at
that also change the data type of "ga_tag" to u32 in order to match
the IOMMU spec.
Fixes: b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC (de-)activation code")
Cc: stable@vger.kernel.org # v5.4+
Reported-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Kishon Vijay Abraham I <kvijayab@amd.com>
Link: https://lore.kernel.org/r/20230405130317.9351-1-kvijayab@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c770657bd2 upstream.
Using standard mode, rare false ACK responses were appearing with
i2cdetect tool. This was happening due to NACK interrupt triggering
ISR thread before register access interrupt was ready. Removing the
NACK interrupt's ability to trigger ISR thread lets register access
ready interrupt do this instead.
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 3b2f8f82da ("i2c: omap: switch to threaded IRQ support")
Signed-off-by: Reid Tonking <reidt@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ba1199ec5 ]
KASAN report null-ptr-deref:
==================================================================
BUG: KASAN: null-ptr-deref in bdi_split_work_to_wbs+0x5c5/0x7b0
Write of size 8 at addr 0000000000000000 by task sync/943
CPU: 5 PID: 943 Comm: sync Tainted: 6.3.0-rc5-next-20230406-dirty #461
Call Trace:
<TASK>
dump_stack_lvl+0x7f/0xc0
print_report+0x2ba/0x340
kasan_report+0xc4/0x120
kasan_check_range+0x1b7/0x2e0
__kasan_check_write+0x24/0x40
bdi_split_work_to_wbs+0x5c5/0x7b0
sync_inodes_sb+0x195/0x630
sync_inodes_one_sb+0x3a/0x50
iterate_supers+0x106/0x1b0
ksys_sync+0x98/0x160
[...]
==================================================================
The race that causes the above issue is as follows:
cpu1 cpu2
-------------------------|-------------------------
inode_switch_wbs
INIT_WORK(&isw->work, inode_switch_wbs_work_fn)
queue_rcu_work(isw_wq, &isw->work)
// queue_work async
inode_switch_wbs_work_fn
wb_put_many(old_wb, nr_switched)
percpu_ref_put_many
ref->data->release(ref)
cgwb_release
queue_work(cgwb_release_wq, &wb->release_work)
// queue_work async
&wb->release_work
cgwb_release_workfn
ksys_sync
iterate_supers
sync_inodes_one_sb
sync_inodes_sb
bdi_split_work_to_wbs
kmalloc(sizeof(*work), GFP_ATOMIC)
// alloc memory failed
percpu_ref_exit
ref->data = NULL
kfree(data)
wb_get(wb)
percpu_ref_get(&wb->refcnt)
percpu_ref_get_many(ref, 1)
atomic_long_add(nr, &ref->data->count)
atomic64_add(i, v)
// trigger null-ptr-deref
bdi_split_work_to_wbs() traverses &bdi->wb_list to split work into all
wbs. If the allocation of new work fails, the on-stack fallback will be
used and the reference count of the current wb is increased afterwards.
If cgroup writeback membership switches occur before getting the reference
count and the current wb is released as old_wd, then calling wb_get() or
wb_put() will trigger the null pointer dereference above.
This issue was introduced in v4.3-rc7 (see fix tag1). Both
sync_inodes_sb() and __writeback_inodes_sb_nr() calls to
bdi_split_work_to_wbs() can trigger this issue. For scenarios called via
sync_inodes_sb(), originally commit 7fc5854f8c ("writeback: synchronize
sync(2) against cgroup writeback membership switches") reduced the
possibility of the issue by adding wb_switch_rwsem, but in v5.14-rc1 (see
fix tag2) removed the "inode_io_list_del_locked(inode, old_wb)" from
inode_switch_wbs_work_fn() so that wb->state contains WB_has_dirty_io,
thus old_wb is not skipped when traversing wbs in bdi_split_work_to_wbs(),
and the issue becomes easily reproducible again.
To solve this problem, percpu_ref_exit() is called under RCU protection to
avoid race between cgwb_release_workfn() and bdi_split_work_to_wbs().
Moreover, replace wb_get() with wb_tryget() in bdi_split_work_to_wbs(),
and skip the current wb if wb_tryget() fails because the wb has already
been shutdown.
Link: https://lkml.kernel.org/r/20230410130826.1492525-1-libaokun1@huawei.com
Fixes: b817525a4a ("writeback: bdi_writeback iteration must not skip dying ones")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Hou Tao <houtao1@huawei.com>
Cc: yangerkun <yangerkun@huawei.com>
Cc: Zhang Yi <yi.zhang@huawei.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 43ec16f145 upstream.
There is a crash in relay_file_read, as the var from
point to the end of last subbuf.
The oops looks something like:
pc : __arch_copy_to_user+0x180/0x310
lr : relay_file_read+0x20c/0x2c8
Call trace:
__arch_copy_to_user+0x180/0x310
full_proxy_read+0x68/0x98
vfs_read+0xb0/0x1d0
ksys_read+0x6c/0xf0
__arm64_sys_read+0x20/0x28
el0_svc_common.constprop.3+0x84/0x108
do_el0_svc+0x74/0x90
el0_svc+0x1c/0x28
el0_sync_handler+0x88/0xb0
el0_sync+0x148/0x180
We get the condition by analyzing the vmcore:
1). The last produced byte and last consumed byte
both at the end of the last subbuf
2). A softirq calls function(e.g __blk_add_trace)
to write relay buffer occurs when an program is calling
relay_file_read_avail().
relay_file_read
relay_file_read_avail
relay_file_read_consume(buf, 0, 0);
//interrupted by softirq who will write subbuf
....
return 1;
//read_start point to the end of the last subbuf
read_start = relay_file_read_start_pos
//avail is equal to subsize
avail = relay_file_read_subbuf_avail
//from points to an invalid memory address
from = buf->start + read_start
//system is crashed
copy_to_user(buffer, from, avail)
Link: https://lkml.kernel.org/r/20230419040203.37676-1-zhang.zhengming@h3c.com
Fixes: 8d62fdebda ("relay file read: start-pos fix")
Signed-off-by: Zhang Zhengming <zhang.zhengming@h3c.com>
Reviewed-by: Zhao Lei <zhao_lei1@hoperun.com>
Reviewed-by: Zhou Kete <zhou.kete@h3c.com>
Reviewed-by: Pengcheng Yang <yangpc@wangsu.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
