[ Upstream commit b153a0bb41 ]
The PMON_CONFIG register on ADM1272 is a 16 bit register. Writing a 8 bit
value into it clears the upper 8 bits of the register, resulting in
unexpected side effects. Fix by writing the 16 bit register value.
Also, it has been reported that temperature readings are sometimes widely
inaccurate, to the point where readings may result in device shutdown due
to errant overtemperature faults. Improve by enabling temperature sampling.
While at it, move the common code for ADM1272 and ADM1278 into a separate
function, and clarify in the error message that an attempt was made to
enable both VOUT and temperature monitoring.
Last but not least, return the error code reported by the underlying I2C
controller and not -ENODEV if updating the PMON_CONFIG register fails.
After all, this does not indicate that the chip is not present, but an
error in the communication with the chip.
Fixes: 4ff0ce227a ("hwmon: (pmbus/adm1275) Add support for ADM1272")
Fixes: 9da9c2dc57 ("hwmon: (adm1275) enable adm1272 temperature reporting")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230602213447.3557346-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f2778b1b ]
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0501fdec10 ]
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e93 ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9358de193 ]
The hfi1 user SDMA pinned-page cache will leave a stale cache entry when
the cache-entry's virtual address range is invalidated but that cache
entry is in-use by an outstanding SDMA request.
Subsequent user SDMA requests with buffers in or spanning the virtual
address range of the stale cache entry will result in packets constructed
from the wrong memory, the physical pages pointed to by the stale cache
entry.
To fix this, remove mmu_rb_node cache entries from the mmu_rb_handler
cache independent of the cache entry's refcount. Add 'struct kref
refcount' to struct mmu_rb_node and manage mmu_rb_node lifetime with
kref_get() and kref_put().
mmu_rb_node.refcount makes sdma_mmu_node.refcount redundant. Remove
'atomic_t refcount' from struct sdma_mmu_node and change sdma_mmu_node
code to use mmu_rb_node.refcount.
Move the mmu_rb_handler destructor call after a
wait-for-SDMA-request-completion call so mmu_rb_nodes that need
mmu_rb_handler's workqueue to queue themselves up for destruction from an
interrupt context may do so.
Fixes: f48ad614c1 ("IB/hfi1: Move driver out of staging")
Fixes: 00cbce5cbf ("IB/hfi1: Fix bugs with non-PAGE_SIZE-end multi-iovec user SDMA requests")
Link: https://lore.kernel.org/r/168451393605.3700681.13493776139032178861.stgit@awfm-02.cornelisnetworks.com
Reviewed-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b002760f87 ]
Commit df8fc4e934 ("kbuild: Enable -fstrict-flex-arrays=3") triggers a
warning for fortified memset():
In function 'fortify_memset_chk',
inlined from 'irdma_clr_wqes' at drivers/infiniband/hw/irdma/uk.c:103:4:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem here isthat the inner array only has four 8-byte elements, so
clearing 4096 bytes overflows that. As this structure is part of an outer
array, change the code to pass a pointer to the irdma_qp_quanta instead,
and change the size argument for readability, matching the comment above
it.
Fixes: 551c46edc7 ("RDMA/irdma: Add user/kernel shared libraries")
Link: https://lore.kernel.org/r/20230523111859.2197825-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1a78babd ]
Fix build errors in soc/fsl/qe/usb.c when QUICC_ENGINE is not set.
This happens when PPC_EP88XC is set, which selects CPM1 & CPM.
When CPM is set, USB_FSL_QE can be set without QUICC_ENGINE
being set. When USB_FSL_QE is set, QE_USB deafults to y, which
causes build errors when QUICC_ENGINE is not set. Making
QE_USB depend on QUICC_ENGINE prevents QE_USB from defaulting to y.
Fixes these build errors:
drivers/soc/fsl/qe/usb.o: in function `qe_usb_clock_set':
usb.c:(.text+0x1e): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0x2a): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0xbc): undefined reference to `qe_setbrg'
powerpc-linux-ld: usb.c:(.text+0xca): undefined reference to `cmxgcr_lock'
powerpc-linux-ld: usb.c:(.text+0xce): undefined reference to `cmxgcr_lock'
Fixes: 5e41486c40 ("powerpc/QE: add support for QE USB clocks routing")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202301101500.pillNv6R-lkp@intel.com/
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Leo Li <leoyang.li@nxp.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Nicolas Schier <nicolas@jasle.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60413129ee ]
When using the codec through the generic audio graph card, there are at
least two calls of es8316_set_dai_sysclk(), with the effect of limiting
the allowed sample rates according to the MCLK/LRCK ratios supported by
the codec:
1. During audio card setup, to set the initial MCLK - see
asoc_simple_init_dai().
2. Before opening a stream, to update MCLK, according to the stream
sample rate and the multiplication factor - see
asoc_simple_hw_params().
In some cases the initial MCLK might be set to a frequency that doesn't
match any of the supported ratios, e.g. 12287999 instead of 12288000,
which is only 1 Hz below the supported clock, as that is what the
hardware reports. This creates an empty list of rate constraints, which
is further passed to snd_pcm_hw_constraint_list() via
es8316_pcm_startup(), and causes the following error on the very first
access of the sound card:
$ speaker-test -D hw:Analog,0 -F S16_LE -c 2 -t wav
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
Note that all subsequent retries succeed thanks to the updated MCLK set
at point 2 above, which uses a computed frequency value instead of a
reading from the hardware registers. Normally this would have mitigated
the issue, but es8316_pcm_startup() executes before the 2nd call to
es8316_set_dai_sysclk(), hence it cannot make use of the updated
constraints.
Since es8316_pcm_hw_params() performs anyway a final validation of MCLK
against the stream sample rate and the supported MCLK/LRCK ratios, fix
the issue by ensuring that sysclk_constraints list is only set when at
least one supported sample rate is autodetected by the codec.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f07342903 ]
The following error occurs when trying to restore a previously saved
ALSA mixer state (tested on a Rock 5B board):
$ alsactl --no-ucm -f /tmp/asound.state store hw:Analog
$ alsactl --no-ucm -I -f /tmp/asound.state restore hw:Analog
alsactl: set_control:1475: Cannot write control '2:0:0:ALC Capture Target Volume:0' : Invalid argument
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
ALCLVL | dB gain
-------+--------
0000 | -16.5
0001 | -15.0
0010 | -13.5
.... | .....
0111 | -6.0
1000 | -4.5
1001 | -3.0
1010 | -1.5
.... | .....
1111 | -1.5
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cf765e598 ]
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes: e027da3427 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861bc1d288 ]
omap2 contains a hack to define tick_broadcast() on non-SMP
configurations in place of the normal SMP definition. This one
causes a warning because of a missing prototype:
arch/arm/mach-omap2/board-generic.c:44:6: error: no previous prototype for 'tick_broadcast'
Make sure to always include the header with the declaration.
Fixes: d86ad463d6 ("ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs")
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230516153109.514251-9-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419013740e ]
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
Fixes: 000bc17817 ("ARM: ep93xx: switch to GENERIC_CLOCKEVENTS")
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230516153109.514251-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24b495508 ]
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78ad ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd9e329af7 ]
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fb912e5e1 ]
DSI sink devices typically want the DSI host powered up and configured
before they are powered up. pre_enable is the place this would normally
happen, but they are called in reverse order from panel/connector towards
the encoder, which is the "wrong" order.
Add a new flag pre_enable_prev_first that any bridge can set
to swap the order of pre_enable (and post_disable) for that and the
immediately previous bridge.
Should the immediately previous bridge also set the
pre_enable_prev_first flag, the previous bridge to that will be called
before either of those which requested pre_enable_prev_first.
eg:
- Panel
- Bridge 1
- Bridge 2 pre_enable_prev_first
- Bridge 3
- Bridge 4 pre_enable_prev_first
- Bridge 5 pre_enable_prev_first
- Bridge 6
- Encoder
Would result in pre_enable's being called as Panel, Bridge 1, Bridge 3,
Bridge 2, Bridge 6, Bridge 5, Bridge 4, Encoder.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20221205173328.1395350-5-dave.stevenson@raspberrypi.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Stable-dep-of: dd9e329af7 ("drm/bridge: ti-sn65dsi83: Fix enable/disable flow to meet spec")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500f823db ]
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27654df20 ]
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1464e48d69 ]
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ffec92e70 ]
The model property should be at the top level, let's move it out
of the pinctrl node.
Fixes: d2eaf949d2 ("ARM: dts: omap3-gta04a5one: define GTA04A5 variant with OneNAND")
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7061b6af34 ]
When map() is called on a detached domain, the domain does not exist in
the device so we do not send a MAP request, but we do update the
internal mapping tree, to be replayed on the next attach. Since this
constitutes a successful iommu_map() call, return *mapped in this case
too.
Fixes: 7e62edd7a3 ("iommu/virtio: Add map/unmap_pages() callbacks implementation")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20230515113946.1017624-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
