[ Upstream commit 040f2dbd20 ]
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e131d1ac ]
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd20 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8217f07a50 ]
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd20 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a09d2d00af ]
In pxa3xx_gcu_write, a count parameter of type size_t is passed to words of
type int. Then, copy_from_user() may cause a heap overflow because it is used
as the third argument of copy_from_user().
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c17a253870 ]
When System.map was generated, the kernel used mksysmap to filter the
kernel symbols, we need to filter "L0" symbols in LoongArch architecture.
$ cat System.map | grep L0
9000000000221540 t L0
The L0 symbol exists in System.map, but not in .tmp_System.map. When
"cmp -s System.map .tmp_System.map" will show "Inconsistent kallsyms
data" error message in link-vmlinux.sh script.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba912afbd6 ]
For irq_domain_associate() to work the virq descriptor has to be
pre-allocated in advance. Otherwise the following happens:
WARNING: CPU: 0 PID: 0 at .../kernel/irq/irqdomain.c:527 irq_domain_associate+0x298/0x2e8
error: virq128 is not allocated
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.78-... #1
...
Call Trace:
[<ffffffff801344c4>] show_stack+0x9c/0x130
[<ffffffff80769550>] dump_stack+0x90/0xd0
[<ffffffff801576d0>] __warn+0x118/0x130
[<ffffffff80157734>] warn_slowpath_fmt+0x4c/0x70
[<ffffffff801b83c0>] irq_domain_associate+0x298/0x2e8
[<ffffffff80a43bb8>] octeon_irq_init_ciu+0x4c8/0x53c
[<ffffffff80a76cbc>] of_irq_init+0x1e0/0x388
[<ffffffff80a452cc>] init_IRQ+0x4c/0xf4
[<ffffffff80a3cc00>] start_kernel+0x404/0x698
Use irq_alloc_desc_at() to avoid the above problem.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 214a9dc7d8 ]
Fix the calculation of the resend age to add a microsecond value as
microseconds, not nanoseconds.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d863036d ]
If the local processor work item for the rxrpc local endpoint gets requeued
by an event (such as an incoming packet) between it getting scheduled for
destruction and the UDP socket being closed, the rxrpc_local_destroyer()
function can get run twice. The second time it can hang because it can end
up waiting for cleanup events that will never happen.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e1e867f4 ]
The pfuze_chip::regulator_descs is an array of size
PFUZE100_MAX_REGULATOR, the pfuze_chip::pfuze_regulators
is the pointer to the real regulators of a specific device.
The number of real regulator is supposed to be less than
the PFUZE100_MAX_REGULATOR, so we should use the size of
'regulator_num * sizeof(struct pfuze_regulator)' in memcpy().
This fixes the out of bounds access bug reported by KASAN.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20220825111922.1368055-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
From: Dave Chinner <dchinner@redhat.com>
commit 7684e2c438 upstream.
When doing a direct IO that spans the current EOF, and there are
written blocks beyond EOF that extend beyond the current write, the
only metadata update that needs to be done is a file size extension.
However, we don't mark such iomaps as IOMAP_F_DIRTY to indicate that
there is IO completion metadata updates required, and hence we may
fail to correctly sync file size extensions made in IO completion
when O_DSYNC writes are being used and the hardware supports FUA.
Hence when setting IOMAP_F_DIRTY, we need to also take into account
whether the iomap spans the current EOF. If it does, then we need to
mark it dirty so that IO completion will call generic_write_sync()
to flush the inode size update to stable storage correctly.
Fixes: 3460cac1ca ("iomap: Use FUA for pure data O_DSYNC DIO writes")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: removed the ext4 part; they'll handle it separately]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandan.babu@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7500a99281 upstream.
Kernel bugzilla: 216301
When doing direct writes we need to also invalidate the mapping in case
we have a cached copy of the affected page(s) in memory or else
subsequent reads of the data might return the old/stale content
before we wrote an update to the server.
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54c3931957 ]
Currently, The arguments passing to lockdep_hardirqs_{on,off} was fixed
in CALLER_ADDR0.
The function trace_hardirqs_on_caller should have been intended to use
caller_addr to represent the address that caller wants to be traced.
For example, lockdep log in riscv showing the last {enabled,disabled} at
__trace_hardirqs_{on,off} all the time(if called by):
[ 57.853175] hardirqs last enabled at (2519): __trace_hardirqs_on+0xc/0x14
[ 57.853848] hardirqs last disabled at (2520): __trace_hardirqs_off+0xc/0x14
After use trace_hardirqs_xx_caller, we can get more effective information:
[ 53.781428] hardirqs last enabled at (2595): restore_all+0xe/0x66
[ 53.782185] hardirqs last disabled at (2596): ret_from_exception+0xa/0x10
Link: https://lkml.kernel.org/r/20220901104515.135162-2-zouyipeng@huawei.com
Cc: stable@vger.kernel.org
Fixes: c3bc8fd637 ("tracing: Centralize preemptirq tracepoints and unify their usage")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6463d3930b ]
VPP_WRAP_OSD1_MATRIX_COEF22.Coeff22 is documented as being bits 0-12,
not 16-28.
Without this the output tends to have a pink hue, changing it results
in better color accuracy.
The vendor kernel doesn't use this register. However the code which
sets VIU2_OSD1_MATRIX_COEF22 also uses bits 0-12. There is a slightly
different style of registers for configuring some of the other matrices,
which do use bits 16-28 for this coefficient, but those have names
ending in MATRIX_COEF22_30, and this is not one of those.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Fixes: 728883948b ("drm/meson: Add G12A Support for VIU setup")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908155243.687143-1-stuart.menefy@mathembedded.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 279c12df8d ]
Commit e39d5ef678 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 345e5c8a1c ("powerpc: Add interrupt support to mpc8xxx_gpio").
Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:
[ 15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
[ 15.267168] lm90 0-004c: cannot request IRQ 49
[ 15.272708] lm90: probe of 0-004c failed with error -22
Fixes: 345e5c8a1c ("powerpc: Add interrupt support to mpc8xxx_gpio")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a9d683b48 ]
The NFSv4.0 protocol only supports open() by name. It cannot therefore
be used with open_by_handle() and friends, nor can it be re-exported by
knfsd.
Reported-by: Chuck Lever III <chuck.lever@oracle.com>
Fixes: 20fa190272 ("nfs: add export operations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f945a792f ]
Commit 78c44d910d ("drivers/of: Fix depth when unflattening devicetree")
forgot to fix up the depth check in the loop body in unflatten_dt_nodes()
which makes it possible to overflow the nps[] buffer...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Fixes: 78c44d910d ("drivers/of: Fix depth when unflattening devicetree")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/7c354554-006f-6b31-c195-cdfe4caee392@omp.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 47311db8e8 upstream.
Users may have explicitly configured their tracefs permissions; we
shouldn't overwrite those just because a second mount appeared.
Only clobber if the options were provided at mount time.
Note: the previous behavior was especially surprising in the presence of
automounted /sys/kernel/debug/tracing/.
Existing behavior:
## Pre-existing status: tracefs is 0755.
# stat -c '%A' /sys/kernel/tracing/
drwxr-xr-x
## (Re)trigger the automount.
# umount /sys/kernel/debug/tracing
# stat -c '%A' /sys/kernel/debug/tracing/.
drwx------
## Unexpected: the automount changed mode for other mount instances.
# stat -c '%A' /sys/kernel/tracing/
drwx------
New behavior (after this change):
## Pre-existing status: tracefs is 0755.
# stat -c '%A' /sys/kernel/tracing/
drwxr-xr-x
## (Re)trigger the automount.
# umount /sys/kernel/debug/tracing
# stat -c '%A' /sys/kernel/debug/tracing/.
drwxr-xr-x
## Expected: the automount does not change other mount instances.
# stat -c '%A' /sys/kernel/tracing/
drwxr-xr-x
Link: https://lkml.kernel.org/r/20220826174353.2.Iab6e5ea57963d6deca5311b27fb7226790d44406@changeid
Cc: stable@vger.kernel.org
Fixes: 4282d60689 ("tracefs: Add new tracefs file system")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a472613f5 upstream.
The soc/fsl/dpio driver will perform a soc_device_match()
to determine the optimal cache settings for a given CPU core.
If FSL_GUTS is not enabled, this search will fail and
the driver will not configure cache stashing for the given
DPIO, and a string of "unknown SoC" messages will appear:
fsl_mc_dpio dpio.7: unknown SoC version
fsl_mc_dpio dpio.6: unknown SoC version
fsl_mc_dpio dpio.5: unknown SoC version
Fixes: 51da14e96e ("soc: fsl: dpio: configure cache stashing destination")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220901052149.23873-2-matt@traverse.com.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e597e2aff upstream.
Some RX errors, notably when disconnecting the cable, increase the RCSR
register. Once half full (0x7fff), an interrupt flood is generated. I
measured ~3k/s interrupts even after the RX errors transfer was
stopped.
Since we don't read and clear the RCSR register, we should disable this
interrupt.
Fixes: 87461f7a58 ("net: phy: DP83822 initial driver submission")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a stable-specific patch.
I botched the stable-specific rewrite of
commit b67fbebd4c ("mmu_gather: Force tlb-flush VM_PFNMAP vmas"):
As Hugh pointed out, unmap_region() actually operates on a list of VMAs,
and the variable "vma" merely points to the first VMA in that list.
So if we want to check whether any of the VMAs we're operating on is
PFNMAP or MIXEDMAP, we have to iterate through the list and check each VMA.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3b82d26bc ]
2 keymap fixes for the Acer Aspire One AOD270 and the same hardware
rebranded as Packard Bell Dot SC:
1. The F2 key is marked with a big '?' symbol on the Packard Bell Dot SC,
this sends WMID_HOTKEY_EVENTs with a scancode of 0x27 add a mapping
for this.
2. Scancode 0x61 is KEY_SWITCHVIDEOMODE. Usually this is a duplicate
input event with the "Video Bus" input device events. But on these devices
the "Video Bus" does not send events for this key. Map 0x61 to KEY_UNKNOWN
instead of using KE_IGNORE so that udev/hwdb can override it on these devs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220829163544.5288-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 478814a558 ]
TCP_FIN_WAIT2 and TCP_LAST_ACK were not handled, the connection is closing
so we can ignore them and avoid printing the "unhandled state"
warning message.
[ 1298.852386] nvmet_tcp: queue 2 unhandled state 5
[ 1298.879112] nvmet_tcp: queue 7 unhandled state 5
[ 1298.884253] nvmet_tcp: queue 8 unhandled state 5
[ 1298.889475] nvmet_tcp: queue 9 unhandled state 5
v2: Do not call nvmet_tcp_schedule_release_queue(), just ignore
the fin_wait2 and last_ack states.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1fa076706 ]
There is a timing issue captured during ishtp client sending stress tests.
It was observed during stress tests that ISH firmware is getting out of
ordered messages. This is a rare scenario as the current set of ISH client
drivers don't send much data to firmware. But this may not be the case
going forward.
When message size is bigger than IPC MTU, ishtp splits the message into
fragments and uses serialized async method to send message fragments.
The call stack:
ishtp_cl_send_msg_ipc->ipc_tx_callback(first fregment)->
ishtp_send_msg(with callback)->write_ipc_to_queue->
write_ipc_from_queue->callback->ipc_tx_callback(next fregment)......
When an ipc write complete interrupt is received, driver also calls
write_ipc_from_queue->ipc_tx_callback in ISR to start sending of next fragment.
Through ipc_tx_callback uses spin_lock to protect message splitting, as the
serialized sending method will call back to ipc_tx_callback again, so it doesn't
put sending under spin_lock, it causes driver cannot guarantee all fragments
be sent in order.
Considering this scenario:
ipc_tx_callback just finished a fragment splitting, and not call ishtp_send_msg
yet, there is a write complete interrupt happens, then ISR->write_ipc_from_queue
->ipc_tx_callback->ishtp_send_msg->write_ipc_to_queue......
Because ISR has higher exec priority than normal thread, this causes the new
fragment be sent out before previous fragment. This disordered message causes
invalid message to firmware.
The solution is, to send fragments synchronously:
Use ishtp_write_message writing fragments into tx queue directly one by one,
instead of ishtp_send_msg only writing one fragment with completion callback.
As no completion callback be used, so change ipc_tx_callback to ipc_tx_send.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
