Since the Qualcomm sdhci-msm device-tree binding has been converted
to yaml format, 'make dtbs_check' reports a number of issues with
ordering of 'clocks' & 'clock-names' for sdhci nodes:
arch/arm64/boot/dts/qcom/ipq8074-hk10-c2.dtb: sdhci@7824900:
clock-names:0: 'iface' was expected
arch/arm64/boot/dts/qcom/ipq8074-hk10-c2.dtb: sdhci@7824900:
clock-names:1: 'core' was expected
arch/arm64/boot/dts/qcom/ipq8074-hk10-c2.dtb: sdhci@7824900:
clock-names:2: 'xo' was expected
Fix the same by updating the offending 'dts' files.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220514215424.1007718-5-bhupesh.sharma@linaro.org
The Light Pulse Generator describes a hardware block responsible for
displaying colors and patterns on an RGB LED (usually used for [battery]
status and notifications), and drive PWM signals for general-purpose
(ie. backlight) LEDs. The availability and usage of the individual
channels differ per board and is hence left for individual platform DTs
to configure.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
[bjorn: Dropped #address/size-cells]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220511190718.764445-3-marijn.suijten@somainline.org
The current settings refer to "blsp_spi1" function which isn't defined.
For this reason an attempt to enable blsp1_spi1 interface results in
the probe failure below:
[ 3.492900] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[ 3.502460] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[ 3.517725] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[ 3.532998] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[ 3.548277] spi_qup: probe of 78b6000.spi failed with error -22
Fix this by making the functions used in qcs404.dtsi to match the contents
of drivers/pinctrl/qcom/pinctrl-qcs404.c.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220611195713.131597-1-andrey.konovalov@linaro.org
The NVMEM bindings expect that 'bits' property holds offset and size of
region within a byte, so it applies a constraint of <0, 7> for the
offset. Using 25 as HSTX trim offset is within 4-byte QFPROM word, but
outside of the byte:
sdm630-sony-xperia-nile-discovery.dtb: qfprom@780000: hstx-trim@240:bits:0:0: 25 is greater than the maximum of 7
sdm630-sony-xperia-nile-discovery.dtb: qfprom@780000: gpu-speed-bin@41a0:bits:0:0: 21 is greater than the maximum of 7
Align the offsets to match the bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505113802.243301-6-krzysztof.kozlowski@linaro.org
Introduce the Qualcomm SA8540P automotive platform and the SA8295P ADP
development board.
The SA8540P and SC8280XP are fairly similar, so the SA8540P is built
ontop of the SC8280XP dtsi to reduce duplication. As more advanced
features are integrated this might be re-evaluated.
This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs (NSPs crashes shortly after
booting) and USB.
The SA8295P ADP contains four PM8450 PMICs, which according to their
revid are compatible with PM8150. They are defined within the ADP for
now, to avoid creating additional .dtsi files for PM8150 with just
addresses changed - and to allow using the labels from the schematics.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-6-bjorn.andersson@linaro.org
Add basic support for the SC8280XP reference device, which allows it to
boot to a shell (using EFIFB) with functional storage (UFS), USB,
keyboard, touchpad, touchscreen, backlight and remoteprocs.
The PMICs are, per socinfo, reused from other platforms. But given that
the address of the PMICs doesn't match other cases and that it's
desirable to label things according to the schematics a new dtsi file is
created to represent the reference combination of PMICs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-5-bjorn.andersson@linaro.org
The PM8916 and PMS405 PMIC GPIOs are interrupt controllers, as described
in the bindings and used by the driver. Drop the interrupts (apparently
copied from downstream tree), just like in commit 61d2ca503d ("arm64:
dts: qcom: fix pm8150 gpio interrupts"):
qcs404-evb-4000.dtb: gpio@c000: 'interrupts' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
qcs404-evb-4000.dtb: gpio@c000: 'interrupt-controller' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508135932.132378-4-krzysztof.kozlowski@linaro.org
The CAMSS DTSI device node, which came after the bindings were merged,
got the interrupts ordered differently then specified in the bindings:
sdm630-sony-xperia-nile-pioneer.dtb: camss@ca00000: interrupt-names:0: 'csid0' was expected
Reordering them to match bindings should not cause ABI issues, because
the driver relies on names, not ordering.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220509144714.144154-4-krzysztof.kozlowski@linaro.org
The CAMSS DTSI device node, which came after the bindings were merged,
got the regs ordered differently then specified in the bindings:
sdm636-sony-xperia-ganges-mermaid.dtb: camss@ca00000: reg-names:0: 'csi_clk_mux' was expected
Reordering them to match bindings should not cause ABI issues, because
the driver relies on names, not ordering.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220509144714.144154-3-krzysztof.kozlowski@linaro.org
The CAMSS DTSI device node, which came after the bindings were merged,
got the clocks ordered differently then specified in the bindings:
sdm636-sony-xperia-ganges-mermaid.dtb: camss@ca00000: reg-names:4: 'csid3' was expected
Reordering them to match bindings should not cause ABI issues, because
the driver relies on names, not ordering.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220509144714.144154-2-krzysztof.kozlowski@linaro.org
The bindings require that every pin configuration comes with 'function'
property. There is also no 'drive-strength' property but
'qcom,drive-strength':
msm8994-msft-lumia-octagon-cityman.dtb: gpios@c000: amsel-high-state: 'oneOf' conditional failed, one must be fixed:
'drive-strength' does not match any of the regexes: 'pinctrl-[0-9]+'
'bias-pull-up', 'drive-strength', 'function', 'pins' do not match any of the regexes: '(pinconf|-pins)$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-9-krzysztof.kozlowski@linaro.org
