[ Upstream commit 92babc9938 ]
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Fixes: 1c28799257 ("iio: light: isl29501: Add support for the ISL29501 ToF sensor.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-9-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec90b52c07 ]
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a potential
kernel data leak, making for a less minimal fix.
Fixes: 55707294c4 ("iio: light: Add support for vishay vcnl4035")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-8-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78bcae8616 ]
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b4f167ef3 ]
Driver code call 'devm_of_pci_get_host_bridge_resources'
to get resources and properly fill 'bridge->windows' and
'bridge->dma_ranges'. After parsing the ranges and store
as resources, at the end it makes a call to pci function
'pci_add_resource_offset' to set the offset for the
memory resource. To calculate offset, resource start address
subtracts pci address of the range. MT7621 does not need
any offset for the memory resource. Moreover, setting an
offset got into 'WARN_ON' calls from pci devices driver code.
Until now memory range pci_addr was being '0x00000000' and
res->start is '0x60000000' but becase pci controller driver
was manually setting resources and adding them using pci function
'pci_add_resource' where a zero is passed as offset, things
was properly working. Since PCI_IOBASE is defined now for
ralink we don't set nothing manually anymore so we have to
properly fix PCI address for this range to make things work
and the new pci address must be set to '0x60000000'. Doing
in this way the subtract result obtain zero as offset
and pci device driver code properly works.
Fixes: d59578da2b ("staging: mt7621-dts: add dts files")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210614100617.28753-4-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e02a3b9458 ]
There is a leak in rtl8712 driver.
The problem was in non-freed adapter data if
firmware load failed.
This leak can be reproduced with this code:
https://syzkaller.appspot.com/text?tag=ReproC&x=16612f02d00000,
Autoload must fail (to not hit memory leak reported by syzkaller)
There are 2 possible ways how rtl871x_load_fw_cb() and
r871xu_dev_remove() can be called (in case of fw load error).
1st case:
r871xu_dev_remove() then rtl871x_load_fw_cb()
In this case r871xu_dev_remove() will wait for
completion and then will jump to the end, because
rtl871x_load_fw_cb() set intfdata to NULL:
if (pnetdev) {
struct _adapter *padapter = netdev_priv(pnetdev);
/* never exit with a firmware callback pending */
wait_for_completion(&padapter->rtl8712_fw_ready);
pnetdev = usb_get_intfdata(pusb_intf);
usb_set_intfdata(pusb_intf, NULL);
if (!pnetdev)
goto firmware_load_fail;
... clean up code here ...
}
2nd case:
rtl871x_load_fw_cb() then r871xu_dev_remove()
In this case pnetdev (from code snippet above) will
be zero (because rtl871x_load_fw_cb() set it to NULL)
And clean up code won't be executed again.
So, in all cases we need to free adapted data in rtl871x_load_fw_cb(),
because disconnect function cannot take care of it. And there won't be
any race conditions, because complete() call happens after setting
intfdata to NULL.
In previous patch I moved out free_netdev() from r8712_free_drv_sw()
and that's why now it's possible to free adapter data and then call
complete.
Fixes: 8c213fa591 ("staging: r8712u: Use asynchronous firmware loading")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/81e68fe0194499cc2e7692d35bc4dcf167827d8f.1623620630.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce793c0ab ]
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Found during an audit of all callers of iio_push_to_buffers_with_timestamp()
Fixes: 8fe78d5261 ("iio: vcnl4000: Add buffer support for VCNL4010/20.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-7-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d36fa106 ]
We should not dereference ->dual_link_port if it is NULL and lane bonding
is requested. For this reason move lane bonding configuration happen
inside the block where ->dual_link_port != NULL.
Fixes: 54509f5005 ("thunderbolt: Add KUnit tests for path walking")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aafe93516b ]
Every time the hub signals a reset while we (device) are hsotg->connected,
dwc2_hsotg_core_init_disconnected() is called, which in turn calls
dwc2_hs_phy_init().
GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if
hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the
default one: 0x5, corresponding to 16-bit) is always different from
hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every
time (usbcfg != usbcfg_old), which causes 2 issues:
1) The call to dwc2_core_reset() does another reset 300us after the initial
Chirp K of the first reset (which should last at least Tuch = 1ms), and
messes up the High-speed Detection Handshake: both hub and device drive
current into the D+ and D- lines at the same time.
2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always
the default one (0x5).
Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset()
fixes both issues. It is now set even when select_phy is false because the
cost of the Core Soft Reset is removed.
Fixes: 1e868545f2 ("usb: dwc2: gadget: Move gadget phy init into core phy init")
Signed-off-by: Clément Lassieur <clement@lassieur.org>
Link: https://lore.kernel.org/r/20210603155921.940651-1-clement@lassieur.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 867f8d18df ]
This patch will be the workaround to fix getting the wrong device ID on the rare chance.
It seems like something unstable when the system resumes. e.g. the bus clock
This patch tries to read the device ID to check several times.
After the test, the driver will get the correct device ID the second time.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210111092740.9128-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d460bb6c64 ]
In commit b02002cc4c ("s390/pci: Implement ioremap_wc/prot() with
MIO") we implemented both ioremap_wc() and ioremap_prot() however until
now we had not set HAVE_IOREMAP_PROT in Kconfig, do so now.
This also requires implementing pte_pgprot() as this is used in the
generic_access_phys() code enabled by CONFIG_HAVE_IOREMAP_PROT. As with
ioremap_wc() we need to take the MMIO Write Back bit index into account.
Moreover since the pgprot value returned from pte_pgprot() is to be used
for mappings into kernel address space we must make sure that it uses
appropriate kernel page table protection bits. In particular a pgprot
value originally coming from userspace could have the _PAGE_PROTECT
bit set to enable fault based dirty bit accounting which would then make
the mapping inaccessible when used in kernel address space.
Fixes: b02002cc4c ("s390/pci: Implement ioremap_wc/prot() with MIO")
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ceed9988a ]
irq_exit() is always called on async stack. Therefore select
HAVE_IRQ_EXIT_ON_IRQ_STACK and get a tiny optimization in
invoke_softirq().
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b21a503ad ]
print_iommu_info prints the EFR register and then the decoded list of
features on a separate line:
pci 0000:00:00.2: AMD-Vi: Extended features (0x206d73ef22254ade):
PPR X2APIC NX GT IA GA PC GA_vAPIC
The second line is emitted via 'pr_cont', which causes it to have a
different ('warn') loglevel compared to the previous line ('info').
Commit 9a295ff0ff attempted to rectify this by removing the newline
from the pci_info format string, but this doesn't work, as pci_info
calls implicitly append a newline anyway.
Printing the decoded features on the same line would make it quite long.
Instead, change pci_info() to pr_info() to omit PCI bus location info,
which is also shown in the preceding message. This results in:
pci 0000:00:00.2: AMD-Vi: Found IOMMU cap 0x40
AMD-Vi: Extended features (0x206d73ef22254ade): PPR X2APIC NX GT IA GA PC GA_vAPIC
AMD-Vi: Interrupt remapping enabled
Fixes: 9a295ff0ff ("iommu/amd: Print extended features in one line to fix divergent log levels")
Link: https://lore.kernel.org/lkml/alpine.LNX.2.20.13.2104112326460.11104@monopod.intra.ispras.ru
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: iommu@lists.linux-foundation.org
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20210504102220.1793-1-amonakov@ispras.ru
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce52ec5bee ]
Commit 1366a3db3d ("staging: unisys: visorbus: visorchipset_init clean
up gotos") assigns the initial value -ENODEV to the local variable 'err',
and the first several error branches will return this value after "goto
error". But commit f1f537c2e7 ("staging: unisys: visorbus: Consolidate
controlvm channel creation.") overwrites 'err' in the middle of the way.
As a result, some error branches do not successfully return the initial
value -ENODEV of 'err', but return 0.
In addition, when kzalloc() fails, -ENOMEM should be returned instead of
-ENODEV.
Fixes: f1f537c2e7 ("staging: unisys: visorbus: Consolidate controlvm channel creation.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210528082614.9337-1-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9108109457 ]
Currently the cfam_read and cfam_write functions return the provided
number of bytes given in the count parameter and not the error return
code in variable rc, hence all failures of read/writes are being
silently ignored. Fix this by returning the error code in rc.
Addresses-Coverity: ("Unused value")
Fixes: d1dcd67825 ("fsi: Add cfam char devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Link: https://lore.kernel.org/r/20210603122812.83587-1-colin.king@canonical.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1649a5260 ]
During more massive generation of interrupts, the IRQ got stuck,
and the subdevices did not see any new interrupts. That happens
especially at wonky USB supply in combination with ADC reads.
To fix that trigger the IRQ at level low instead of falling edge.
Fixes: 0c81604516 ("mfd: rn5t618: Add IRQ support")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ce9fc5ecd ]
We set the max_active iSCSI EH works to 1, so all work is going to execute
in order by default. However, userspace can now override this in sysfs. If
max_active > 1, we can end up with the block_work on CPU1 and
iscsi_unblock_session running the unblock_work on CPU2 and the session and
target/device state will end up out of sync with each other.
This adds a flush of the block_work in iscsi_unblock_session.
Link: https://lore.kernel.org/r/20210525181821.7617-17-michael.christie@oracle.com
Fixes: 1d726aa6ef ("scsi: iscsi: Optimize work queue flush use")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d431153e7 ]
The BusLogic driver has build errors on ia64 due to a name collision (in
the #included FlashPoint.c file). Rename the struct field in struct
sccb_mgr_info from si_flags to si_mflags (manager flags) to mend the build.
This is the first problem. There are 50+ others after this one:
In file included from ../include/uapi/linux/signal.h:6,
from ../include/linux/signal_types.h:10,
from ../include/linux/sched.h:29,
from ../include/linux/hardirq.h:9,
from ../include/linux/interrupt.h:11,
from ../drivers/scsi/BusLogic.c:27:
../arch/ia64/include/uapi/asm/siginfo.h:15:27: error: expected ':', ',', ';', '}' or '__attribute__' before '.' token
15 | #define si_flags _sifields._sigfault._flags
| ^
../drivers/scsi/FlashPoint.c:43:6: note: in expansion of macro 'si_flags'
43 | u16 si_flags;
| ^~~~~~~~
In file included from ../drivers/scsi/BusLogic.c:51:
../drivers/scsi/FlashPoint.c: In function 'FlashPoint_ProbeHostAdapter':
../drivers/scsi/FlashPoint.c:1076:11: error: 'struct sccb_mgr_info' has no member named '_sifields'
1076 | pCardInfo->si_flags = 0x0000;
| ^~
../drivers/scsi/FlashPoint.c:1079:12: error: 'struct sccb_mgr_info' has no member named '_sifields'
Link: https://lore.kernel.org/r/20210529234857.6870-1-rdunlap@infradead.org
Fixes: 391e2f2560 ("[SCSI] BusLogic: Port driver to 64-bit.")
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1e1d532da ]
fwnode_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
OTOH, the successful iteration will drop reference count under the hood, no need
to do it twice.
Fixes: 242b81170f ("leds: lp50xx: Add the LP50XX family of the RGB LED driver")
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 807553f8bf ]
When requesting GPIO line the probe can be deferred.
In such case don't spam logs with an error message.
This can be achieved by switching to dev_err_probe().
Fixes: 5c1d824cda ("leds: lm3697: Introduce the lm3697 driver")
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f55db1c7fa ]
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 9a5c1c64ac ("leds: lm3692x: Change DT calls to fwnode calls")
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c5f655c44 ]
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
In the older code the same is implied with device_for_each_child_node().
Fixes: 11e1bbc116 ("leds: lm36274: Introduce the TI LM36274 LED driver")
Fixes: a448fcf19c ("leds: lm36274: don't iterate through children since there is only one")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
